Search Documents

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By Hollis R. G, Tuppurainen J. M I

Improved control of non-ferrous sintering operations requires the on-line measurement of sinter quality. No on-line measure of sinter quality is currently available, however, previous work has shown that the raw mix chemistry and peak sintering temperature determine the mineral phases formed and hence the resulting Blast Furnace behaviour. Control of these factors should therefore lead to improved quality control. In this paper, the development of a simplified heat and mass balance model of the Sinter Plant at Mt Isa is described. The model used available plant data to calculate raw mix composition and a simplified reaction scheme to predict sinter composition. The extent of reaction is inferred from the flue gas analyses. Off-line testing of a dynamic version demonstrated that actual plant performance could be predicted with reasonable accuracy.

Jan 1, 1989

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

By Jamie Girard Dwyer, Edward McHugh, Stanley Miller, Jeffrey Whyatt

This user's guide covers the operation of a suite of three computer programs-Bplane, Bstepp, and Bwedge. These programs can be used to evaluate the potential for plane shear, step-path, and wedge failures along the crest of a slope bench. Such failures reduce the width of a catch bench and may compromise the bench's ability to catch rolling or sliding material before it reaches miners working below. The Bplane and Bwedge programs address sliding of blocks defined by continuous planar joints. The Bstepp program examines sliding of blocks defined by more complex failure surfaces that include steeply dipping cross joints and may even include breaks across small bridges of intact rock. The programs are applicable to jointed rock masses where the joints are small relative to the overall slope and form a number of sets with uniform statistical characteristics within a slope sector. The theoretical basis, application, and operation of these programs are described.

Jan 3, 2007

By J. Loubser

The concept of caring is in most cases confused with material needs and not psychological needs. By giving employees a job, most managers think that employees should be grateful and return the favour by being loyal, productive and working safely. Other managers hold the view that employees can be lucky to have a job. To show and demonstrate that management are caring for the safety of the workforce requires involvement, dedication and commitment. Obtaining the trust and respect of the workforce should be the main thrust of any organization because within trust and respect lie the secret of optimal safety performance. In the last 70 years, all the fatalities and serious injuries that occurred in the mining industry can be traced back to one thing, non-caring. The same safety non-compliances are still observed, reported and planned against as 70 years ago, and strange as it may sound, the same injuries occur the same way. The question could be asked: Does the mining industry need more risk assessments? More codes of conduct? More engineering. Or does the mining industry need more caring?

Jan 1, 2010

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By Kazusuke Sato, Takahiro Uno, Koji Hoshino

"A novel Ni coating technique of Ni(OH)2 powders was developed to improve the positive-electrode performance· of the Ni-MH batteries. It was found out that Ni(OH)2 powder was reduced by N2H4 without any catalysts in an alkaline - solution at high temperatures. In result of observation of pH and potential changes in the solution during the reaction, it was found that the reduced species was HNio2- ion dissociated from Ni(OH)2 in the alkaline solution. The molar fraction of reduced Ni of the Ni(OH)2 was increased in proportion to the amount of added N2H4. At the small Ni fraction, a porous Ni layer was formed on the surface of Ni(OH)2 powder. Open cell tests were carried out with the paste type electrodes made of either the Ni coated Ni(OH)2 powder or non-coat powder, and cell performances were compared. In result, it was found that the Ni coating technique is effective on improvement in the utilization of Ni(OH); as a positive-electrode active material under high current densities.IntroductionNi-MH rechargeable battery is generally used for the power source of portable machines and electric vehicles because of its good performance at high energy density and. long term cyclical life as well as cleanness and good safety. Cell component materials have been improved respectively, and as concerns ·the positive-electrode reducing 'the internal resistance is a principal problem to improve the discharging performance at higher current densities.In recent years, improved Ni(OH)2 powders coated with conductive materials as NI. or CoOOH have been developed for the· positive-electrode active materials in order to· reduce the internal resistance of the electrode1)· 2) The Ni coated Ni(OH)2, however, is costly because it is fabricated by .the -non-electrode plate technique which needs a expensive precious ·metal catalyst as PdC12We found that Ni(OH)2 powder was reduced by N2H4 without any cryatalysts in an alkaline solution at high temperatures. After the treatment, Ni(OH)2 powder become gray color like Ni powder from light-green color; and. turned into a magnetic. In this study, the mechanism of the -reducing reaction was investigated to apply the reactions .to a novel Ni coating technique of Ni(OH)2 powders, · and the performance of the Ni coated Ni(OH)2 powder obtained by the reducing process was evaluated as an -positive-electrode active material of Ni-MH batteries."

Jan 1, 2000

By Holger Witthaus

The conditions of great mining depth and multi-seam¬longwalling require a special method of rockbolting, It can be described as a control loop which is based on the elements of planning, drivage and measurement. Different planning elements such as the results of the observation of physical models, numerical programmes for calculation of stress-distribution and support success, lab and underground support testing and the knowledge of strata behaviour underground including geotechnical classification are used to get best results. The increasing geotechnical information collected during drivage of roadways are used to estimate and minimise the risks of support-overload. The repeated plan/acutal comparison during the use of roadway and continuously monitoring of support and roadways provided the opportunity of optimising support design during the process of drivage and if necessary in front and after of the longwall face.

Jan 1, 2000

Longhole stope overbreak has always been a source of unwanted cost within the underground mining industry, and efforts to control it using various rock reinforcement systems have long been a rock engineering challenge. At the Pasminco Mining Broken Hill Operations trials have been carried out using an innovative cable bolt reinforcement system known as Rib-Roc. The system, based loosely on the Swedish Rib-in-Roc concept, utilises zones or ribs of heavily reinforced rock in the troublesome hangingwall and back areas of longhole stoping. The trials were carried out under a strict qualitative and quantitative scientific stope measurement program utilising rock mechanics instrumentation. Not only did the trial demonstrate the success of the system but data obtained was useful in implementing the system virtually as standard practice throughout the operation.

Jan 1, 1995

By D. A. Riva

"The Line Creek Project is located in southeastern British Columbia, approximately 25 kilometres north of Sparwood. The design is to produce a total of2.7 million tonnes of coal annually. This is made up of1.4million tonnes of thermal coal and 1.3 million tonnes of metallurgical coal.Construction commenced in the spring of 1980 and mining operations began in July 1981. The thermal processing plant, maintenance and dry facilities, as well as extensive road and bridge construction, were completed in early 1982. A collective agreement was signed with the International Union of Operating Engineers, Local 115, in June 1981.The first unit train left Line Creek on February 18, 1982 with a load of thermal coal bound for the Ssangyong Corporation in Southern Korea. It was the start of a ten-year contract to supply 350,000 tonnes annually to fire their cement kilns. Additional contracts for 750,000 tonnes will fuel the boilers of Korea Electric Company's San Chon Po and Go-Jeong power stations. Metallurgical coal shipments are scheduled to leave the Roberts Bank port in Vancouver in April 1983.Tracking an introductory presentation given at the 1981 CIM Annual General Meeting in Calgary, this paper highlights the salient developments by which ""The Line Creek Project"" has progressed during the past year to the"" Line Creek Operation"". Line Creek has com e on stream as scheduled and will meet all contractual commitments pertaining to timing, volumes and quality for thermal coal. The first train load left the plant in mid-February, and the first boat load to Korea departed Roberts Bank in mid-April. Metallurgical coal deliveries will commence in April 1983."

Jan 1, 1982

By John C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1994

By McHenry Mosier

Although local conditions at each mining property affect the percentage of increase in drilling speed for a given reduction in gage of bit, the results of drilling tests conducted at the Mount Weather testing adit show such a large advantage in favor of the smaller gages that they should be indicative of the possibilities at most mines. GENERAL DISCUSSION Although it is common knowledge among miners that drilling speed increases with reduction in gage of bit, the large amount o this increase is not so universally realized, A recent Bureau of Mines4/ survey of drilling practices in 28 metal mines showed that the maximum gage of starters is 3 inches and that at 50 percent of the mines starters are 2-1/4 inches or larger, Because this size appears too large for conditions at most mines where abrasion is moderate and where powder distribution permits, the use of smaller bits presents a favorable opportunity for reducing drilling costs.

Jan 1, 1939

By Kourosh Shahriar, Kazem Oraee, Ezzeddin Bakhtavar

"In this paper, a relationship between dependant parameters and the crown pillar thickness is first introduced. This relationship defines geotechnical problems caused by thin pillars and economic considerations created by pillars that are thicker than the optimum size. For this purpose, a dimensional analysis as an effective physico-mathematical tool was used. This technique restructures the original dimensional variables of a problem into a set of dimensionless products using the constraints imposed upon them by their dimensions. A model is hence introduced that calculates the optimum pillar thickness. The relationship introduced here and the method applied can be used by mining engineers in all situations where a combined open-pit and block caving method is deemed to be the most appropriate mining method.INTRODUCTIONMany deposits can be mined entirely with the open-pit method; others must be worked underground from the very beginning. In addition, there are the near-surface deposits with considerable vertical extent. Although they are initially exploited by the open pit method, there is often a ""transition depth"" where decision has to be made about changing to underground methods.Some of the biggest open-pit mines worldwide will reach their final pit limits in the next 10 to 15 years. Furthermore, there are many mines planning to change from open-pit to underground mining due to increasing extraction depths and environmental requirements. In this way, it is likely that block and/or panel caving will enable the operations to continue achieving a high production rate at low costs as an underground method (Bakhtavar et al., 2009).In these cases, it is often necessary to consider a crown pillar beneath the transition depth (open-pit floor) before starting an underground caving stope method (Figure 1).There are generally two kinds of crown pillar: a ""surface crown pillar"" and ""crown pillar between open-pit and underground mining."" In general, they both play the similar role in mining. Since the primary purpose of a surface crown pillar is to protect surface land users, the mine, and those working in it from inflows of water, soil, and rock; it is vital that the surface crown pillars remain stable throughout their life. When a crown pillar could potentially remain between open-pit and underground mining it is specially proposed to prevent water entering from the open-pit floor into the stope, as well as to reduce open-pit wall and floor caving."

Jan 1, 2010

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By T. E. Gray

This report describes the preparation characteristics of the more significant coal beds in Washington County, Pa. It is one of a series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. More than 15 million tons of coal was produced in Washington County in 1956; 89.8 percent was cleaned mechanically in 10 cleaning plants. The Bureau of Mines has estimated that 2,280 million tons of recoverable coal remained in beds 28 inches thick or more as of January 1, 1954.

Jan 1, 1959

By P. J. Poirier, J. A. Meech, H. Raabe

"An Expert System has been implemented to assist operators in applying knowledge about froth conditions in the control of the flotation circuit at Highland Valley Copper. For some time, the personnel at Highland Valley Copper have recognized that froth type is a useful indicator of good operating conditions. However, the operating strategy based on froth type recognition is an ad-hoc skill in which different operators use a variety of terms, features and procedures to identify and solve problems. The first phase of this project developed an on-line consultative system to advise and tutor so that the diffuse expertise could be rationalized and consolidated into a standardized format.The second phase has brought this knowledge into a real-time environment to advise the operators on the floor in identifying froth types and troubleshooting corrective action. This paper describes the steps taken to acquire the knowledge, to design the required system features and to implement the real-time version of this system.INTRODUCTIONThe use of expert systems in the mineral industry has been gaining popularity in recent years. Minnova Inc, Les Mines Selbaie, Wabush Mines, Potash Corporation of Saskatchewan are just a few examples of Canadian mining companies that use expert systems to monitor or control their plants. Applications in the field of flotation include Brenda Mines (Edwards, 1992), Mt Isa Mines Ltd (Lacouture et al, 1991), Outokumpu (Karhu, 1989) and Kidd Creek (Burrows et al., 1989).Expert systems are defined as ""computer systems that apply reasoning methodologies on knowledge in a specific domain in order to render advice or recommendations much like a human expert"" (Turban, 1988). The main areas of application are diagnosis, training, process monitoring and control, and design. There are basically two main types of expert systems: Consultative systems, which are off-line applications in diagnosis and design, and on-line realtime systems, used for supervisory process control and real-time advising."

Jan 1, 1993

By James W. Malcolmson

This paper treats of the history and development of the Sierra Mojada mines in the north of Mexico, the character and extent of the ore-deposits, and the methods of mining the ore. The growth of the smelting industry in Mexico in recent years is, to a large degree, due directly to the output of the lead-bearing ores from the Sierra Mojada mines, and at the present time (1901) new smelters are being built, looking to this district for their supply of lead-ores. These mines are located in the southern part of the State of Coahuila, in the Republic of Mexico, in latitude 27 24' N. and longitude 103O 43' W. of Greenwich. The last account of the Sierra Mojada published in our transactions was contributed by Mr. Richard E. Chism, in October, 1886.* Since that time some 3,000,000 tons of ore have been extracted from the mines, and much additional information has been developed regarding the mineral deposits. Since 1886, the Mexican Northern railroad, 78 miles in length, has been built from Escalon, connecting the camp with the Mexican Central railway, a trunk-line from El Paso, Texas, to Mexico City. The distances by rail from Sierra Mojada to the principal smelting-centers are as follows : To Torreon, Coahuila, Mex., 179 miles; to Monterey, Nuevo Leon, Mex., 422 miles; to El Paso, Tex., U. S., 494 miles; to Aguas Calientes, A. C., Mex., 522 miles; to San Luis Potosi, 8. L. P., Mex., 644 miles; to Pueblo, Colorado, U. S., 1158 miles; to Argentine, Kans., U. S.,

Jan 1, 1902