Search Documents

By E. G. Parker

"Sherritt's zinc pressure leaching process converts zinc sulphide concentrates directly to zinc sulphate solutions and elemental sulphur. Thus, one pressure process step replaces both the roasting and leaching operations of the conventional roast-leach route. In addition, high single-pass extractions eliminate the need for residue treatments to recover unleached zinc. Because pressure leaching produces elemental sulphur, rather than sulphur dioxide, acid plants and smoke stacks are not required, and air pollution control and work-place hygiene are greatly improved. .In 1977, Cominco Ltd. and Sherritt Gordon Mines Limited jointly operated a three-tonne-per-day pilot plant to demonstrate pressure oxidative leaching of Sullivan zinc concentrate and the subsequent separation of elemental sulphur. The process consisted of regrinding the concentrate, continuous leaching at 150°C at elevated oxygen pressures in a four compartment autoclave and the subsequent recovery of elemental sulphur, either in the molten liquid form from a decantation autoclave or as a flotation concentrate. Of the zinc contained in the concentrate, 97% was extracted in 90 minutes, and 96% of the sulphur was converted to the elemental form.Following the successful pilot campaign, Cominco began building the world's first commercial zinc pressure leaching plant. This plant, which was in operation by late 1980, will eventually treat about 25% of Cominco's planned zinc capacity of270,000 tonnes per year.This paper describes the general process principles, the results obtained from the pilot plant and the integration of the process into Cominco's operations at Trail. The application of pressure leaching to a ""grass-roots"" plant is also discussed, and compared with conventional roast-leaching."

Jan 1, 1981

The floatability of a bituminous coal in NaG solutions was evaluated using a modified Hallimond tube to delineate the role of the electrostatic interaction between bubbles and particles in determining the coal hydrophobicity. Zeta potential measurements showed that bubbles are negatively charged in the entire pH range tested, while coal particles are positively charged below pH 6.0 and negatively charged above it. Also, both sodium and chloride ions were confirmed to act as indifferent ions without any specific effects for both coal particles and bubbles. Flotation as a function of pH exhibited a maximum and minimum at low salt concentrations which is shown to be determined mainly by the coal hydrophobicity as measured by a new hydrophobic levitation technique. At high salt concentrations (above 0.1 mole/dm3), the flotation without such maximum or minimum is controlled by the electrostatic interaction between the bubble and the particle.

Jan 1, 1992

By R. H. Singleton

ThE purpose of this investigation was to determine the effect of cerium upon the nonmetallic inclusions found in cast and wrought steel containing various amounts of sulfur, oxygen, and nitrogen. Interest of the Physical Metallurgy Laboratory of the Watertown Arsenal Laboratories in this type of research was stimulated by the reports from industry that rare-earth metals imparted beneficial effects upon the mechanical properties of steel, but that the mechanism was not understood. Berry and Dorvel' found that misch metal improved the impact properties of aluminum-killed cast steels. They reported that the rare earths modified the intergranular-film type nonmetallic inclusion, present with aluminum as the sole deoxidant, to a randomly distributed globular type. Lilliequist and Mickelson2 observed the improvement of ductility and toughness of quenched and tempered cast steels through rare-earth additions. They also observed the change from angular to duplex inclusions when rare earths were present. They con-

Jan 1, 1960

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By W. A. Kracht

The McGill Bubble Size Analyzer, with the original image-capturing device (digital video camera), has a proven record for measuring bubble size distributions that are relatively narrow, such as in mechanical cells with frother. However, some problems arise when dealing with bubble size distributions characterized by a bi-modal shape and wide range of sizes such as found in some flotation columns. To measure wide bubble size distributions it is necessary to increase both the resolution to image the small bubbles and the viewing area to include the large bubbles. This can be done using a digital still camera: digital still cameras can have higher resolution than the digital video cameras currently used and with the proper lens the viewing area may be increased without resolution loss. The digital still camera approach was used to measure bubble size distributions in flotation columns at different operations in Chile. A comparison with typical bubble size distributions generated with mechanical cells is presented.

Jan 1, 2007

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

By J. A. Arias

The oxidation kinetics of pyrite and refractory gold concentrates in acidified ferrous sulfate solutions in the presence of oxygen-sulfur dioxide gas mixtures has been studied. The effect of temperature, pulp density and gas composition were determined. The optimum oxidation rate was obtained at 80°C and 2 percent sulfur dioxide in the gas mixture. The oxidation of the sulfide minerals is attributed to the presence of ferric ions, which are continuously regenerated by the gas mixture. The objective of this study is to find a new hydrometallurgical method to render sulfidic refractory gold ores amenable to cyanization.

Jan 1, 1993

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985

June was the month in which AIME was founded in the year of 1871. For some reason, February was selected as the month for the legal Annual Meeting. One can't help thinking wistfully of Annual Meetings in June but of course this is not the reality. Because the Centennial Ceremonies are taking place in February, that month has been chosen as the one in which MINING ENGINEERING, the monthly magazine of the Society of Mining Engineers, a constituent society of AIME, is publishing its Commemorative is- sue to celebrate the event. SME and ME take a proprietary air about AIME. This is mostly because AIME started as the American Institute of Mining Engineers. Metallurgy was added to the name in 1919 and Petroleum in 1956. The official abbreviation of "AIME" has been retained, however.

Jan 1, 1971

By P. A. Mascaró, N. Chacon, A. A. Cecchi

"This document shows the development of a system called the “On-line charge level determination in SAG mills” (abbreviated as Jc). The Jc variable has certainly been difficult to measure due to the relevant number of factors and variables that affect the grinding phenomena inside semi autogenous (SAG) mills. To assess the feasibility stage of the proposed system, it was necessary to carry out two tests in different sized SAG mills, 38´ × 22´ and 36´ × 15´, respectively. In each test, the system was configured with a battery of sensors of the following types: (1) strain gauge, (2) accelerometer, and (3) gyroscope. The first step involved for charge level determinations was to determine kidney foot and shoulder by means of a study of the energy-impacts on shell structures. The second step consisted of correlating the measured grinding operational variables with the actual charge levels obtained from SAG mill crash stops. This system development is extremely useful and relevant for providing approximations about mass balances inside SAG mills. It will be a suitable tool for explaining “tonnes per hour” variations and determining optimal points under various operating conditions.INTRODUCTIONThere has been a growing necessity for technologies capable of obtaining “on-line data” of the main comminution variables in order to increase throughput. Computer systems have taken an important role in providing important solutions by means of processing on-line device signals (commonly referred to as monitoring). In semi autogenous (SAG) milling, there are many examples of monitoring devices that allow the operational staff to obtain detailed information both mechanically and electronically inside a grinding circuit. In this context, a new technology has been developed to obtain “Jc total charge (%) online” in two different SAG mills called Vibro-Energy® System.As part of the analysis performed by JKsimMet® the Jb/Jc was estimated because it has an important impact on SAG mill throughput. Different scenarios were simulated and contrasted at various theoretical Jb/Jc values in a baseline circuit (Figure 1)."

Jan 1, 2016

By Mathias Jern, Ruilin Yang

A blast vibration model has been developed that simulates effects of almost all blast design parameters on the blast vibration peak particle velocity (PPV) from a production blast with multiple blastholes at a given point of interest in the rock. The velocity of detonation (VoD), initiation points, explosive types (density, VoD, energy), charge decoupling, and decking in each blasthole are simulated along with other blast design parameters. The information from signature hole blast vibration and the blast design are the input to the model. The model can be used to assess blast damage in proximity of blastholes as well as far field vibration PPV.

Jan 1, 2019

By Jeffrey S. Walker

Abandoned underground mine openings are susceptible to collapse because of the mining methods used, the character of the overburden, and the typically large, wide entries with minimal roof support. The final effect of the collapse of the underground workings is surface subsidence. To reduce the probability of subsidence, methods to backfill the mine void with various types of materials have been developed. This U.S. Bureau of Mines report describes the available technologies for subsidence abatement and discusses their operation and application. The basis of these abatement methods is the replacement of the mined material with mine waste. Backfilling of mine voids is the most common method of stabilization used to abate subsidence and protect surface structures. Hydraulic flushing and grouting, using remote methods from single or multiple boreholes, are the most often-used methods for the placement of backfill material. Other subsidence abatement techniques are available and may be more appropriate under different conditions. These other techniques include pneumatic stowing, either by in-mine or remote methods, and various point support methods that do not completely fill the mine void and are used for the protection of small areas of the land surface and surface structures.

Jan 1, 1993

By Juan Patricio Ibáñez

Separation of arsenic and copper from Cu-As-H2S04 electrolytes by electrodialysis has been investigated at room temperature. The effects of current density and pH were studied. An arsenic-free copper solution was obtained for all the tested conditions. The transport efficiency for copper ions was found to be higher than 98% after 3 hours' test. Transport of arsenic and copper through the ion exchange membranes was increased by increasing pH and current density. Solution pH was found to be a key parameter for the separation process, since it controls the speciation of the ions to be transported and the formation of unwanted precipitates which reduce the global efficiency of the electrodialysis process. The main conclusion is that electrodialysis is a promising technique to be used in separating and/or concentrating ions of interest in copper electrometallurgy.

Jan 1, 2003

By E. F. Ferrell

Gold was recovered from scrap electronic 60-40 (tin-lead) solders by drossing with aluminum or zinc at elevated temperatures. The gold, together with other metallic impurities, collected in the dross phase which could then be separated from the molten solder by skimming or filtering. Drossing upgraded the gold concentration by a factor of 10. Further upgrading was achieved by a combination of steps including an oxidation roast and either a combined cyanidation-amalgamation treatment or an aqua regia leach. The gold was then recovered in highly concentrated form from the aqua regia or cyanide solutions by cementation and from the amalgam by volatilization or dissolution of the mercury. The solder was purified by reaction with NaOH to remove dissolved aluminum or with SnCl2 to remove dissolved zinc.

Jan 1, 1976

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30km along strike, although economic resources are confined to a 7 km section in the vicinity of the Macraes township. The shear zone, which typically dips at a low angle (~20 o ) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, ælode schistsÆ and quartz-vein stockworks. Rehabilitation at the mine has focused on creating an environmentally benign site dominated by pasture to allow continuation of the traditional pre-mine farming economy. Changing regional economics, continued urbanisation and a reduction in traditional employment opportunities has seen a rethink in the long-term rehabilitation outcomes. The community has recognised that the rehabilitated site will provide the basis of a viable tourism venture and the creation of a Heritage and Art Park (working title æGolden Point ParkÆ) is the culmination of that process.

Jan 1, 2002

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993

By Sebastian Siebert

Unmanned Aerial Vehicles (UAV) as a data acquisition platform and as a measurement instrument have become attractive for many surveying applications in civil engineering. However, their performance is not well understood for these particular applications. The specific scope of the presented work is the performance evaluation of a UAV system that was built to rapidly acquire mobile 3D mapping data for large earthmoving construction sites. Details to the components of the developed system (hardware and control software) are explained. A novel program for photogrammetric flight planning and its execution for the generation of 3D point clouds from digital mobile images is explained. A performance model for estimating the position error was developed and tested in several realistic construction environments. Results to these tests are presented as they relate in particular to large excavation and earth moving construction sites. Results and experiences with the developed UAV system are in particular useful for researchers or practitioners in need for successfully adapting UAV technology for their application(s).

Aug 1, 2013

By C. G. Williams

This paper describes the planning, development and operation of the Highvale Mine to supply coal to both the existing Sundance and the approved Keephills thermal power plants of Calgary Power Ltd. Reference is also made to the company 's Whitewood Mine, which feeds the Wabamun thermal plant .

Jan 1, 1979

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004