Search Documents

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

By Wenliang Cao, Jidong Li, Mingjie Zhang, Yiyong Wang

In CaC12-CaF 2 System, we studied the electrode process and discharge mechanism of preparation of Al-Ca alloys by fused salt electrolysis with CaO as raw material. The change of back electromotive force after adding CaO was measured by continuous pulse oscillograph method and the discharge process mechanism was also investigated by cyclic voltammetry. The finial results indicate that back electromotive force decreases by 0.6V after CaO of 1 % is added and there was a peak of oxidation current ahead of the potential at which the negative chlorine ions precipitated. According to thermodynamic calculation, it was determined that current peak was caused by the CO2 produced by 0 2 - ionic discharge due to CaO addition.

Jan 1, 2014

By D. R. Douslin

This report describes an inclined-piston pressure gage that operates from a zero-pressure datum level. The gage is adaptable to accurate vapor-pressure measurements in the low and intermediate pressure range, 0.01 to 40 mm (mercury). Residual friction in the oil-lubricated piston-cylinder combination is eliminated by a unique oscillatory method that is free of end thrust on the piston and allows the full sensitivity of the gage to be realized. The axial component of the weight-to-area ratio of the piston is determined by measuring the angle of inclination with a goniometer that can be read to 1 sec. Accuracy of the gage proper is estimated to range from 0.001 to 0.012 mm from lower to upper pressure limits. Its highest practical sensitivity is about 0.0005 mm. As a test, the vapor pressures of ice and water were measured in the range -30° to +20° C.

Jan 1, 1963

By Robert Glass Cleland

FROM the time of its organization down to 1917, a period of more than eighty years, Phelps, Dodge & Co. was seldom involved in what could be called a major labor difficulty. Behind this remarkable record lay both a philosophy and its practical application. The philosophy was an attitude toward society called the Golden Rule. That philosophy had been a living principle in the lives of the founders of the company, Anson Phelps, Daniel James, and William E. Dodge. Their successors, William E. Dodge, Jr., and Daniel Willis James, accepted the same philosophy. Dr. James Douglas governed his life by it. All of these men and their families had given tangible expression to that conviction in benefactions of great magnitude and variety-churches, hospitals, educational institutions, libraries, missionary undertakings, and other organizations for human betterment, such as the Young Men's and Young Women's Christian Associations, and the development of model communities about their mills and factories. According to the best standards of their generation, they had sought to improve the condition of labor,

Jan 1, 1952

By Philippe V. Scheers

Polycrystalline gold, glassy carbon and gold-activated glassy carbon electrodes were compared for the production of hydrogen peroxide by the cathodic reduction of dissolved oxygen. Gold was deposited on glassy carbon by sputtering with a sputter coater and by electrodeposition from a diluted KAuCl4 solution using short potential steps. The sputtered gold particles were not adherent enough, but there were no adhesion problems with the electrodeposited gold particles. The gold coverage of the glassy carbon surface could be varied by applying a different number of potential steps. The overpotential for the electroreduction of oxygen to hydrogen peroxide decreases with increasing gold coverage of the glassy carbon surface, and for gold coverages exceeding about 16 %, the overpotential is close to that observed on polycrystalline gold.

Oct 1, 2003

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

By Thomas T., Read

IN this survey of the progressive development (of education for the mineral industries throughout the United States, the review of .the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. Philadelphia Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1852, when the Pennsylvania, Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1856-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941

By Charles E. Mauk

In 1970, recognizing the great need for an economical, high capacity chemical oxidation process for wastewater treatment, Houston Research began a fundamental study of the available technology, Included was waste characterization; oxidation chemistry for molecular oxygen, ozone and catalyst initiators; kinetics of reaction; gas-liquid contacting methods; and optimization of staged reactors for mixed wastes. Although ozone is the most powerful oxidizer available, the literature contains contradictory reports of its speed and effectiveness. It is now felt to be most likely that many of these early investigations were limited by the ineffectual transfer of ozone from the gas phase into the liquid, and so the investigators were really observing the effects of mass transfer and erroneously trying to interpret the results as if they were chemical reaction data. HR's work considered the cost and effectiveness of gas-liquid contacting in a packed tower, gas sparged contactor, ejector with hold-up tank, and a completely mixed, sparged contactor. The sparged, mixed contactor was found to be most effective and least expensive, and a later investigation settled on the reactor configuration shown in Figure 1 because of its effectiveness of mass transfer and because it lends itself to direct scale-up techniques using laboratory data to design larger reactors.

Jan 1, 1975

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of withstanding explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

Jan 1, 2003

By S. A. Matthes

This Bureau of Mines report describes a system for the dissolution of metal and mineral samples using a microwave heat source. Samples and an acid mixture are placed in sealed polycarbonate vessels. The vessel contents are heated using microwaves, digested for 2 min, and quickly cooled. After the solution is brought to a final volume, the vessel contents are heated an additional 2 min in the microwave oven. Using this method, a slag, a feldspar, and a Ni-Cu alloy were dissolved and analyzed by atomic absorption spectroscopy. Values obtained for Na, K, Cu, Ni, Si, Mg, Mn, Ca, Al, and Fe agreed with certified values and had an average relative standard deviation of 1 pct. This system results in a significant savings in time and expense over traditional methods of sample dissolution, and is ideal for preparing solutions for analysis by atomic absorption, plasma optical emission, or X-ray spectroscopy.

Jan 1, 1983

By Albert L. Toenges

Alaska requires an adequate fuel supply for its development, and has large potential coal reserves ranging from lignite to subbituminous and anthracite. Coal production in the Territory now is less than the requirements. In 1947, production was 361,000 tons, divided about equally between bituminous coal from the Matanuska field and subbituminous coal from the Nenana field. There is need for development of modern mechanized mines, which should produce the required output with a minimum of workers. These mines should not be thought of in the light of large potential capacity, as in the States. However, these new mines should be developed by modern methods, which should result in lower costs than at present. Because of the diverse physical conditions in the coal fields, intensive investigation by diamond drilling is necessary to properly plan the development and equipment of mine sites at minimum cost. The Bureau of Mines is doing this now in the Wishbone Hill area of the Matanuska field. All coal land in Alaska is government-owned and subject to the Coal Leasing Act.

Jan 1, 1949

By Liangying Wen, Zhehan Liao, Jian Xu, Chenguang Bai, Chengfeng Sun, Kaihui Ma, Yang Xu

The difference on particle density causes mass and size segregation in the blast furnace throat, causing poor permeability in radial and circumferential direction. Understanding the effect of density difference on particle spatial-temporal distribution helps stabilize smooth operation and improve energy ef ficiency of blast furnace iron-making process. Based on discrete element method simulation, the influence of density difference on particle segregation behaviors is quantitatively characterized by the proposed method when the binary-sized particles are charged from parallel-type hopper of blast furnace. The results show that increasing the 4 mm particle density aggravates the mass segregation in circumferential and radial direction, and the maximum standard deviation of each ring reaches as great as 0.415. For size segregation, the difference on average mass fraction of small particle between center and edge ring decreases from 0.373 to 0.301. When increasing the 6 mm particle density, the similar particle segregation behaviors could be obtained.

Mar 1, 2018

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to supply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their usefu1 life; however, the partial redesign

Jan 1, 1951

By D. Adiguzel

In this research, providing the sustainability of production quality was aimed for a quarry which is located in Istanbul western part of Turkey and producing concrete aggregates with different types of rock. First, research field was divided in 3 different areas in accordance with the geological differences and parameters that control their product quality, limit values of standards and effect levels were determined. Concrete aggregate conformity tests which are stated in international standards were applied on samples which were taken from these 3 different areas and physical, geometric and chemical properties of each rock type were revealed. The properties of the 3 different types of rock which were produced in the quary were determined and the binary blends were composed. Blending studies were conducted with linear programming technique. In the linear programming model, the cost of aggregate production was aimed to be minimal. The limit values that meet literature and national standards for usability of aggregates in concrete were defined as constraints in the linear programming model and evaluated with objective functions, thus the most suitable aggregate blends were composed. In conclusion, to provide the sustainability of product quality, the most appropriate product blends were composed for the research field and the usability of this model for those quarries were revealed.

Aug 1, 2013

By J. A. Folinsbee

Placer Dome Canada owns and operates the Campbell Mine at Balmertown, in the Northwestern corner of the Province of Ontario, Canada. The mine operates at 1500 stpd and produces in excess of 300,000 oz of gold annually. Recent changes to the gravity concentration circuit have resulted in a 10-15 % increase in gravity recovery. The circuit changes responsible for these improvements will be the focus of this paper.

Jan 1, 1997

By Ulrich Maidl

The use of EPB shields in the so-called mixed face conditions has set new demands to man and machine in EPB shield tunneling. EPB shields were initially conceived to drive in the pressurized closed mode in soft ground, whereas hard rock TBMs were designed to work in the unpressurized open mode. The present use of EPB shields in hard rock and mixed face conditions requires the combination of both technologies by finding best compromise solutions. This paper deals firstly with the geotechnical and mechanical interactions between machine and ground. Further on the critical points such as tool wear and tool replacement are exposed, together with a proposal of best solutions.

Jan 1, 2003

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By J. P. BONARDI, William F. Boericke

BOULDER COUNTY, Colorado, ranked during the war years and until the end of 1918 as one of the foremost tungsten-producing districts of the world. In 1919 production fell off drastically, due to heavy importations of foreign ores from China, Burma and South America. So large were the imports that even after the enactment of a protective tariff in 1922 of 45c. per lb. on tungsten metal, equivalent to $7.14 per unit (201b.) of tungstic acid? (WO,), the stocks of metal in this country were extensive enough to supply the demands of industry, and prevent general resumption of mining by domestic producers. Even today there are only two producers in the Boulder district though at one time as many as twenty separate companies were in operation. About the same ratio holds for other tungsten-producing districts in the country, including California and Nevada. Total consumption of tungsten concentrate in terms of 60 per cent WO2 in the United States amounted to approximately 3790 tons in 1928, according to Frank L. Hess.' Of this amount, domestic mines contributed 1290 tons, and the rest, 2500 tons, was imported. Yet in 1917, with tungsten concentrate selling at $20 per unit, the Boulder district alone produced 2707 tons, indicating the effect of enhanced ore price upon production. It is believed by American tungsten miners that, given a sufficiently high tariff, all the demands of industry can be met by domestic production without placing a prohibitive burden on consumers. For instance, in steel manufacturing the percentage of tungsten entering into the manufacture is so small that, ?regardless of cost, it can constitute but a small fraction of the cost of steel to the buyer.

Jan 1, 1929