Search Documents

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By J. J. Geraghty

U.S. Bureau of Mines researchers investigated the development of an innovative transport system for underground coal mining. A one-half commercial-scale bench model was constructed. Novel magnetic levitation (mag-lev) technology was developed. Frictionless and contact-free transport of a prototype materials container and payload has been demonstrated.

Jan 1, 2010

By A. Wahab Khair

"This paper deals with the description of the capabilities of a unique rotary coal cutting simulator which has been designed and fabricated at West Virginia University. It operates under the simulated mining conditions with in-situ stresses (horizontal and vertical stresses) being applied to a coal block of 18 in. x 15 in . x 6 in located in a suitably designed confining chamber. Cutting drum rotation can be varied from 1 to 40 rpm with the capability of stopping the drum after a predetermined number of rotations. Tests can be performed with four different bit angles, 15, 30, 45 and 60 degrees . A maximum of seven bits could be used in seven different orbits. Various cutting depths up to a maximum of 4 in. is possible.Monitoring devices constitute, Linear Variable Differential Transformers (LVDTs), pressure transducers, cascade Impactors, flow meters, flow controls and drum cutting speed. LVDTs are used to monitor the displacement of the coal block as well as the depth of cut. Pressure transducers are used to monitor the changes in pressure, both due to the thrust and due, to the intermittent cutting nature of the rotary cutting. Flow controls will be used to run the drum at a set rpm between 1 and 40 and to provide a different rate of advance. All the above mentioned devices can be operated and monitored by a fully automated control system. Six-stage cascade impactors are used to determine the mass distribution of dust along the rotation path of the drum. The fracture size, shape and Intensity can be studied by optical microscopy and the dust entrainment by using high speed photography.This equipment will basically be used to study the fracture mechanism in coal, associated with operating and in-situ parameters and further relate It to dust generation and entrainment In underground coal mines."

Jan 1, 1988

By Daniel W. H. Su

The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate post-mining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects.

Jan 1, 1986

By C. W. Volek, J. E. Chappelear

The injection of a hot liquid into initially cool porous media, saturated with the same liquid and surrounded by two impermeable but heat conducting media (cap and base rock), has been studied both experimentally and theoretically. The temperature dependence of the viscosity was included in the theoretical model, but it was assumed that the specilic heats and densities of the various materials were independent of the temperature. Solutions to the theoretical model were approximated by numerical methods. Both theoretical and experimental results indicate that center-line temperatures are significantly higher than boundary temperatures. Comparison of experimental and theoretical results with a cold/hot viscosity ratio 01 19:1 were in reasonable agreement. Theoretical calculations show that the effect of the temperature dependence of viscosity was very significant at ratios of 100:l to 1000:1, which are typical of those that occur when injecting hot water to flood heavy oil reservoirs. INTRODUCTION We consider the problem of prediction of fluid flow and temperature distribution in an initially cold-fluid-filled reservoir on the injection of the same hot liquid by the use of mathematical and physical models. The results reported are for a two-dimensional rectangular section of the reservoir, as shown in Fig. 1. The injection and withdrawal faces are assumed to be equipotentials for fluid flow. The ultimate purpose of such models would be to predict hot-water injection performance. However, we note that in the work presented here, one of the most significant aspects of the problem — the instabilities resulting from two-phase, water and oil flow — is not included. We will not give a historical review, but refer instead to the paper of Spillette and Nielsen,1 which contains a rather complete bibliography and critical discussion. The physical problem is exactly the same as Spillette and Nielsen, except for certain simplifications in our assumptions. The mathematical details are somewhat different, and we will present the details of our method here. The mass flow equation, which is elliptic in character, is handled by successive overrelaxation. The heat flow equation, which is parabolic in character, is handled by a straightforward explicit approximation. Some difficulty arose in the over-all heat balance due to small errors in the solution of the mass flow equation, and we feel that a different formulation of the heat flow equation would be desirable for future work. In addition to the mathematical solutions for the temperature distributions in a porous medium due to the injection of hot liquids, experimental data are presented to check the validity of these solutions. A schematic diagram of the model is shown in Fig. 2. Certain qualitative physical conclusions were obtained from our numerical and experimental results. These are: 1. Assuming high (infinite) conductivity normal to the bedding plane in the reservoir is a poor approximation, and may lead to overestimates of the total heat losses (to cap and base rock) of as much as 50 percent. 2. More heat is retained in the reservoir (per unit of heat injected) for higher viscosity changes. 3. Any particular temperature isotherm moves more rapidly along the center line for higher viscosity changes. Consequently, the approximation of temperature independent viscosity is not suitable for obtaining quantitatively correct results. MATHEMATICAL MODEL Our mathematical model is that of a reservoir of thickness 2h. The problem is idealized from that of a linear hot-water drive, and we imagine that the input face is sufficiently far away from the injection wells that the stream lines enter it normally. Similarly the production wells are far enough from the outflow face that the flow lines leave it normally. The reservoir and surrounding cap and base rock

Jan 1, 1970

Silver-lead ores are widely distributed through- out the Mount Lofty and Flinders Ranges, but none of the deposits is large. Historically the Glen Osmond Mines are the most significant as the site of the first metalliferous mining in Australia, but Talisker was one of the three largest producers of silver-lead in a state whose mining history is dom- inated by copper. The mine is located in a magnificent natural setting on Talisker Conservation Park, near Cape Jervis, southwest of Adelaide (Figure 1). It is exempt from the operations of the Mining Act and listed on the Register of State Heritage Items. The mine and associated township of Silverton were dominated by Cornish influences during the period of principal activity between 1862 and 1872. Silverton, located on a ridge overlooking the mine, grew to a population of about 300 at its peak in 1870 and the area was very much another 'little Cornwall'.

Jan 1, 1987

By Edwards A. B

Yampi Sound is a small channel in the Buccaneer Archapelago (latitude 16° 10' S.; longitude 123° 40' E.), on the northern coast of Western Australia (Fig. 1), about 90 miles north of Derby, and 200 miles north-east of Broome.The iron ore deposits of Yampi Sound occur on an approximately S.E.-N.W. trending belt of islands which form the northern boundary of the Sound (Fig. 2). From east to west they are Koolan Island, Tarrant Island, Usborne Island, Cockatoo Island, Irvine Island, Kathleen Island, Flora Island, and Bathurst Island. To the south of the Sound lie Margaret Island, which is separated from the mainland by a channel only 60 ft. wide, Dorothy Island, and Gibbings Island. Some of the channels between the...

Jan 1, 1938

By Bauer, Alan

In considering blasting it is necessary to consider the drilling and explosives since one is generally concerned with the total cost of muck of a certain size in the pit or through the crusher. To get a current idea of the drilling situation in open pit mines plotted in Fig. 1 are the drilling costs per ton of material vs. hole diameter for rotary drill holes in large limestone, iron ore and taconite operations. The exception is the 2-in. diam hole which was drilled with a percussion drill in limestone.

Jan 1, 1968

By H Beucher

The uranium grade in roll front deposits is the result of successive processes that can be summarised in two steps. First a sedimentary phase, which gives the deposit support, then an oxidation-reduction phenomenon, which leads to the uranium deposit itself. In order to simulate such a deposit, it is important to mimic these different phases. The final aim of such a study is to localise the uranium itself and to reproduce the internal heterogeneity of the orebody in order to simulate the recovery process. The idea in this paper is not to reproduce a genetic approach but to consider the final image of the deposit. Three approaches are proposed. The first one consists of simulating the facies of the sedimentary deposit. The second approach reproduces the distribution of facies resulting from oxidation phenomenon (reduced or oxidised facies). The third approach consists of simulating the mineralisation at the interface of reduced and oxidised areas using the definition of a new data set determined by the grade values. At the end of each approach, the uranium grade could be simulated facies by facies according to the corresponding distribution characteristics. The plurigaussian method dedicated to random set simulations is well-suited for the facies simulations of deposits resulting from several sedimentary processes whether correlated or not. In this paper, the benefit of this method is demonstrated in an actual case study.

Jan 1, 2006

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982

By J. J. Gilvarry, B. H. Bergstorm

The first part of this paper describes a new approach to the problem of energy relationships in fracture and comminution. The basic theoretical method used (as contrasted to previous empirical or semi-empirical approaches) is an attempt to verify or disprove the hypothesis of von Rittinger, In the second part of the paper, theoretical conclusions for the three headings of single fracture, plural fracture, and comminution are tested. Agreement between theory and experimental results is demonstrated. The classical hypotheses on the energy relationship in brittle fracture are those of von Rittinger-that the energy required is proportional to the new surface formed— and the alternative one of Kick.' Over the years, repeated attempts have been made to discriminate experimentally between the two assumptions, or to replace both of them, as has been done by Bond? However, no semblance of agreement seems to exist among different investigators. This paper is the first in a series essaying a new approach to the entire problem of energy relationships in fracture and comminution. The purpose of this program of research is to verify (or disprove) the hypothesis of von Rittinger. In contrast to previous empirical or semi-empirical approaches to the problem, the basic method adopted is theoretical. The prime aim is to determine the distribution function for fragment size theoretically and to verify the predicted distribution experimentally. This approach should make possible determination of the total surface of the particles by integration over the corresponding distribution function; one may hope that this direct procedure will yield more definitive results than use of gas adsorption or other methods. The surface area so obtained can then be compared with experimental energies, as obtained by Bergstrom, Sollenberger, and Mitchell,4 for example. It is convenient to distinguish between single fratture, plural fracture, and comminution. Single fracture of a brittle solid is defined as fracture by an external stress system which is removed instantly and permanently when fracture is initiated. Plural fracture consists of single fracture of the original specimen, followed by a sequence of only a few secondary fractures; comminution differs in that the sequence of secondary fractures consists of a large number of repetitive steps. For single fracture, Gilvarrys has given a rigorous derivation of the proper distribution function for fragment size, based on a closely defined physical model and deduced strictly by the laws of probability. Gilvarry and Bergstrome have compared the predictions of the theory with experiment, and have found excellent agreement. The prior work of Gilvarry and of Gilvarry and Bergstrom considers only single and plural fracture. The purpose of the present paper is to extend the discussion to the case of comminution. For prefatory purposes, the theory of Gilvarry for single fracture will be outlined. The considerations will then be applied to the cases of plural fracture and comminution. SINGLE FRACTURE The derivation is based on the Poisson law.7 For Points distributed with mean density y over a domain, this law states that the probability p(t)dt of one point lying in the range t to t + dt with none in the interval 0 to Ms p(t)dt = ye-yt dt. For this distribution to be valid, it is necessary and sufficient that the points be distributed at random, individually and collectively in the sense of ~~~.7 The former qualification requires that the position of One Point be independent of another, and the latter implies that the probability of a region containing a

Jan 1, 1961

By J. L. Bruce

After six years of war-enforced idleness, Cyprus copper mines are operating again. This relatively long shutdown seems infinitesimal when compared with something like seventeen hundred years of inactivity that followed the important operations of the ancient Romans, and continued until the twentieth century. The historical records of the ancient operators are scarce but full of interest to those who realize that Cyprus copper production was important more than two thousand years ago. This paper, however, will give only a brief review of the ancient history and the evidence of ancient mining which have been quite fully covered in other publications.1-6 The purpose of this paper is to give a general sketch of the Cyprus Mines Corporation's enterprise in the Island of Cyprus, with special emphasis on those conditions and practices which are unusual. The picture is not intended to be complete, and many interesting details will be omitted. Some of these may be described in subsequent papers covering departmental practices. The principal operations of Cyprus Mines Corp. are in Cyprus, where it has leasehold concessions from the Cyprus Government covering about 50 square miles. It holds additional areas under "Prospecting Permits." The consideration for the concessions is a royalty on production, coupled with minimum annual rentals. Cyprus is a British Colony in the Eastern end of the Mediterranean with an area of about 3000 square miles and a population of about 400,000, of which 65 pct may be classed as Greeks on the basis of language, religious training, and traditions. About 25 pct are Moslems, principally of Turkish extraction. Prevailing languages are Greek and Turkish. A large proportion of the supervisory and administrative staff and practically all of the skilled and unskilled craftsmen and laborers are drawn from the native population. The "overseas" staff constitutes not more than 2 pct of the employees. The majority of these are from the United Kingdom, the British Dominions and Colonies. About one-third are from the United States of America. The topography of the Island is rugged, with mountains and foothills covering more than two-thirds of the area. Between the Kyrenea range rising to 3000-ft elevation, along the north coast, and the Troodos range (maximum elevation 6400 ft) occupying the southwest half of the Island, lies a cultivated rolling plain, the "Mesaoria," dry in summer and watered only by the winter rains and by scanty irrigation from small mountain streams and wells in the spring and summer. Climate and natural vegetation are characteristic of semi-arid conditions. The "urban" population, about one-fourth of the total, lives in the five port towns, Famagusta, Larnaca, Limassol, Paphos and Kyrenia, and in the capitol Nicosia, near the center of the Island. The suburban population lives almost entirely in villages or small towns, with very few people residing in isolated country homes.

Jan 1, 1949

By G. S. Hume

Activity in geological exploration and drilling continued in Canada in 1945 at about the same rate as in the previous year, but with disappointing results as far as new production is .concerned. Both in the foothills and on the Plains of Alberta, however, there are wildcat wells that have either given encouraging shows or some production, which are very important in relation to future developments. The normal decline of Turner Valley, the largest producing field in Canada, has continued, and this decrease has not been offset by new discoveries. In addition, the closing of the Canol pipe line on March 31, 1945, isolated the Norman Wells field in the Mackenzie River valley, and the outlet at present. is confined to supplying the relatively small local requirements. This

Jan 1, 1946

BASIC open-hearth slags have no obviously unique features when compared with slags from other metallurgical operations. Open-hearth slags form and exist at temperatures ranging from 2500 to 3100 F (1370 to 1700 C). In the course of an open-hearth heat, the liquid slag changes slowly and continuously in chemical analysis-the changes reflecting changes in temperature, changes in metal analysis, solution of charged materials, solution of feed additions, and solution of refractories. Through- out the process, the slag performs specific primary functions that are responsible for a large measure of the technical and economic importance of basic open-hearth steelmaking. It is intended in this chapter to present the chemical reactions by which the primary functions of basic open-hearth slags are carried out, to describe the physical and chemical principles governing the extent to which these reactions proceed and can be regulated, and finally to indicate the limitations imposed on other features of the process by the fulfillment of the primary functions. Basic open-hearth slags perform three primary functions. First and foremost, the slag provides a means of removing phosphorus from the liquid metal. The ability to remove phosphorus is largely responsible for the widespread use of the basic open- hearth process. Second, the slag serves as a controlling factor in transferring the oxygen required for the other oxidizing reactions. Third, the slag provides a means of eliminating some sulfur from the open-hearth bath. While the extent of sulfur removal is not comparable to that of phosphorus, the ability to remove some sulfur contributes much to the value of the process. The effectiveness with which the slag fulfills its functions varies with temperature and composition. Since operating temperatures are fixed largely by the specified nature of the product and the equipment, the speed and extent to which the functions of the slag are carried out depend largely on its composition. The necessity for regulating slag composition to accomplish the re-

Jan 1, 1951

The mine manager is one of the oldest jobs in the world. Over many centuries the fundamentals of how this job was approached did not change much. However since the later part of the 1980s there has been a dramatic shift in the expectations and role of the mine manager as the pressures of globalisation and consolidation have increased the size of companies and the production levels of mining operations. The changes have been dramatic, with demanding requirements on mine managers to continually improve the skill levels of people, to apply and develop rapidly changing technologies and to consider far broader business issues that need to be managed in a truly globally connected world. This paper will attempt to outline some of the issues, the complexity surrounding them and some of the approaches that have been made to manage them. There is not a single correct answer or approach, but there are many key success factors that have led to some amazing levels of performance being achieved as we go deeper, broader and literally move mountains to meet the customerÆs needs for today and tomorrow. This contrasts with many mining operations in developing countries that still have a traditional approach to how they mine. Society is the river of life that continually flows and changes the environment that surrounds it. The pressures from the customers and world growth, shape and force alterations to be made in an industry that has to live with the far greater primal and uncompromising forces of the earth we mine. This has led to some paradigm shifts in how we accept what we manage. TodayÆs mine manager must manage a far broader range of issues, than just how do we get tonnage out of the mine and product out of the ore. These include but are not limited to technical, commercial, product quality and end use understanding, employee and community issues, environmental and the ever increasing complexities of sustainable development. Organisations will have to look at how they structure their management of the business to manage functions to meet the complexity of different stakeholders needs û the business, the employees, the customer and the broader community within an environment that is becoming more attuned to the harm impacts to the world in which we operate. The attraction and retention of skilled people that contribute to the value and worth of the corporation, will become critical to sustain a companyÆs growth. One of the fundamental elements of successfully doing this will always be the skills of the mine manager and his/her extended team with the continued development and support that they will need to meet these demands.

Jan 1, 2006

By Louis Tellier

SIDBEC commenced detailed planning of major capital expenditures to install integrated steelmaking facilities in 1969. Today, less than IO years later, SIDBEC and its subsidiaries have completed major mining, concentrating, pelletizing, direct reduction ? electric furnace steelmaking and continuous casting plants. The total cost of these projects was almost 1 billion dollars. The philosophy behind the project planning and the evolution of management control are explained. These extensive projects were undertaken during a period of exceptional inflation and a disturbed labour climate, but were nevertheless completed with only modest overruns, with good control of timetables and with exceptionally good start-up performance. Project planning, relations with consulting engineers, introduction of new technology, purchasing and field management and cost control are discussed.

Jan 1, 1979

By P. Thapliyal

The petroleum refining industry generates over a million tons of spent catalyst per year, containing valuable metals. Currently, these materials are recycled to smelting furnaces, but the fundamental mechanisms controlling the recovery processes are poorly understood. Furthermore, submerged injection of finely divided materials is potentially a means to obtain high recoveries of pay metals. In this study, a catalyst containing 10% Ni and 1% Co was injected into 45 kg heats of matte. A copper matte was chosen so that the nickel and cobalt recoveries were measurable. It was found that the recovery ranged from 40 to 700Al, increasing with catalyst feed rate, decreasing with catalyst particle size and decreasing with the oxygen content of the carrier gas. A mathematical model was developed to account for the results, and to permit extrapolation to nickel mattes. The industrial implications are discussed.

Jan 1, 1996

By C. S. Crocker

The Centennial orebody was discovered and named in 1970, Manitoba's centennial year. It is relatively small, about 2 million tons. Strike length varies from 400 to 600 feet and widths from 10 to 60 feet; dip is 75 degrees. Low grade and metal prices demanded low-cost mining, and the mine was developed for conventional sublevel stoping. As the ore lay entirely under a large lake, ground movement had to be avoided and the stopes were to be filled hydraulically. Late in 1973, vertical crater retreat mining was introduced at Inco Limited, Sudbury, to recover pillars between filled stopes. It proved satisfactory and the results were publicized by CIL, who developed the technique. The method seemed to offer some advantages and one stope at Centennial Mine was selected to be mined by VCR while production was maintained from blasthole stopes. The trial stope was safe and showed lower development costs, reduced drilling time, a favourable powder factor and good fragmentation. VCR mining is now an accepted method at HBM&S Co., Ltd., and its use is being extended.

Jan 1, 1979

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By I. E. Odom

A study was made of the physical and chemical nature of silica minerals found as natural impurities in bentonites and montmorillonitic Fuller&apos;s earth clay products as well as in <10 micron dust from eight processing plants. The results show that the silica minerals present in these clay materials are totally encapsulated or encased in clay. No "free" silica minerals could be observed in SEM images of either granular or powder products or in dust samples collected for MSHA crystalline silica analysis. Silica minerals, such as quartz, are identifiable by SEM and EDS analysis only after removing the clay coatings by vigorous washing. After washing it can be observed that all crystalline quartz grains also have diagenetic overgrowths of what is probably opaline silica. The clay and opaline silica encapsulation of quartz plus the strongly hydro scopic nature of montmorillonite are believed to be responsible for there not being a single confirmed case of silicosis among workers in the subject plants after more than 65 years of production.

Jan 1, 1996