Search Documents

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By Joseph B. Perry, G. M. Kirwan

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40º to 75 º. Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938

By H. Foster Bain

Jan 1, 1910

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By Fiona J. Stevens McFadden, Gregory J. Hardie, Mark P. Taylor, William Uru

"Over 20 million tonnes of installed aluminium smelting capacity exists worldwide, with smelter energy con.sumption in the range 14-17 kWh/kg aluminium. In terms of the reduction cell technology itself, the lowest sustained energy consumption is just below 13DC kWh/kg, or 50% energy efficient.For 15 years Comalco Aluminium Ltd. in Australia has been engaged in developing and testing reduction cells that use a refractory hard cathode, composed of a TiBif carbon composite coating over a carbon cathode. This technology has the potential to reduce energy consumption significantly while simultaneously increasing the life of the cells, which is currently limited by wear rate of the conventional carbon cathodes used throughout the worldIntroductionThe successful development of an aluminium wettable cathode technology affords the opportunity to the cell designer and smelter operator to fundamentally change the physical operating characteristics of the Hall-Heroult process. With this revolutionary capability in hand, published papers and patents have indicated that the technology may be exploited in a wide variety of ways to improve the economic performance of aluminium smelting process. Comalco has been developing refractory hard cathode technology for more than 15 years and has been exploring a number of ways that the technology may be commercially applied in a smelter operation [l]."

Jan 1, 2000

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1984 identified no mineral resources or prospects with mineral development potential in the Pit River Canyon Wilderness Study Area (WSA). Basalt suitable for aggregate and fill is in the WSA but rock of this nature is abundant in the region and closer to potential markets.

Jan 1, 1984

By R. C. Bryce

"Accident prevention has been an on-going priorty for five years. In 1987, adherence to the ILCI five-star rating loss control program was started, and a first star was awarded. Extensive training programs have been undertaken to establish standard procedures and upgrade employee skills. Due to its location, Selbaie owns and rents housing in the town of Joutel and contracts a busing service to and from the mine. Employees from other areas are lodged in dormitories and fed in the site dining room. Accounting and warehousing services are carried out in efficient fashion. Employee relations are structured to provide prompt resolution of complaints and differences. No lost time due to industrial relations differences has been encountered during the history of the mine.Safety and Loss ControlAll mines are concerned and occupied with a wide range of activities to ensure the safety of its employees. Selbaie is no exception. Programs to achieve success in safety and loss control have been implanted since the start of construction and development at Selbaie and have followed three interesting stages of evolution."

Jan 1, 1990

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association's ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off's. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By R. W. Jenkins, O. J. Neslage

The need for mechanized drilling to decrease mining costs has resulted in the development of the jumbo from column-and-bar drill carriages to hydraulically controlled jib jumbos. Resultant savings from use of improved jumbos have been high enough usually to retire the machinery investment within a year. The jib jumbo unit has been applied successfully to development and preparation programs and flat-bedded stopes, and an even wider field is forecast for its use.

Jan 1, 1950

By A T. Owen, F A. Benn, J D. Swift, D M. Labbett, A F. Grabsch

The AMIRA P266 æImproving Thickener TechnologyÆ series of projects has sought to provide a firm scientific basis for feedwell and thickener design, a requirement as pressures on water usage in the minerals industry increase. While advanced computational fluid dynamics modelling of feedwell processes has generated the most obvious and successful applications to improving the performance of operating units, such outcomes have drawn heavily on parallel studies into flocculation fundamentals. Central to this has been the development of a linear pipe reactor system that allows the kinetics of flocculated aggregate growth and rupture to be measured for thickener feeds under turbulent pipe flow conditions. This ensures much greater control of the intensity and duration of applied shear than is possible with conventional flocculation test procedures, offering insights into flocculation processes that would be otherwise hidden in time-averaged measurements.

Jan 1, 2009

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

Copper cathode and Uranium Oxide production at WMC (Olympic Dam Corporation) Pty. Ltd. involves processing leach liquors through a copper solvent extraction plant followed by a uranium solvent extraction plant. This paper discusses the processing problems, metallurgical testwork and circuit changes made due to contamination of amine in the oxime circuit and vice versa.

Jan 1, 1996

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau's surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation. The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 2010

By C. H. Mathewson

CHARACTER OF THE WORK IN HAND IN planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100° C. to 1,000° C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,1 in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper.

Jan 7, 1916

By F. N. Earll

4.1 – DEFINITIONS 4.1.1-MINERALS, ROCKS, ORES AND NONMETALLIC MINERALS F. N. EARLL A mineral is a naturally occurring inorganic element or compound. Most minerals are distinctly crystalline in habit, and many commonly occur in well-formed crystals or crystalline aggregates, but a few species are characteristically amorphous or noncrystalline. Nearly 2,000 mineral species are now recognized but, perhaps fortun¬ately, a rather large proportion are rarely encountered. Even so, the application of modern mineral-detection and identification techniques reveals the presence of surprising numbers of mineral species, even in deposits of outwardly simple mineralogy. A rock is an aggregate of grains or crystals of one or more minerals. Some rocks are essentially monomineralic. Thus, limestone consists largely of the mineral calcite, and many sandstones are dominantly quartz. Most rock varieties, however, contain a number of mineral species, and their classification or identification depends upon the minerals present, their relative abundance, and such factors as rock tex¬ture and origin. Ore is defined as an accumulation or deposit of one or more minerals that can be exploited at a profit. The profit criterion commonly is taken somewhat liberally, however, for, although always present, the specific mineral content that constitutes a viable product is transitory. The term ore, usually, but no longer consistently, is restricted to the description of mineral deposits that are of value for their metal content. Nonmetallic deposits, although similar to metallic ores in many respects, generally are valued for the minerals or compounds present, as with rock salt (halite), rather than for individual contained elements, though such minerals as elemental sulfur are of much value. 4.1.2-ROCK TYPES F. N. EARLL Rocks arc grouped tinder three broad headings: (1) igneous rocks formed by the crystallization of magma; (2) sedimentary rocks formed by surface processes of weathering and deposition; and (3) metamorphic rocks, which may have been derived from either of the foregoing, but have undergone important physical and/or chemical changes through the application of heat or pressure, or both. The three groups can he further subdivided for convenient reference. Thus, igneous rocks are described as being abyssal or plutonic if formed at great depth, hypabyssal if formed at intermediate depth, and extrusive or effusive if formed at or on the earth's surface. The sedimentary rock group is similarly subdivided into clastic sediments and chemical precipitates. The clastic sediments form by deposition of preexisting minerals that were released from their place of origin by weathering and were transported to their point of deposition as discrete grains

Jan 1, 1973

By E. Morrice

High-purity lanthanum metal was prepared by electrolysis of La003 in a LaF3-LiF-BaF2 bath at 950° C. The requisite bath temperature for the deposition of molten metal was maintained by supplying the heat as current directly to the electrodes. A current efficiency of about 60 percent was obtained. The lanthanum nodules contained carbon and oxygen as major impurities. The total impurity content was from about 0.1 to 0.2 percent.

Jan 1, 1962

By D. L. H. Forbes

The application of the cyanide process to complex sulphide ores for the extraction of the gold and silver is no longer a novelty; but, as an example showing modern teudencies in this direction, the following description of the new milling process at the Lucky-Tiger mine is offered: The extraordinary richuess of the ore in the upper workings of this mine made any thought of milling in its early days seem unnecessary. Its location in an almost inaccessible part of the rugged mountains just south of the Arizona boundary-line, and 60 miles from the town of Douglas, made the expense of bringing in machinery and sopplies a very serious consideration. But, after the property had been shipping high-grade ore on mule-back for a few years, there remained in the mine a considerable tonnage of vein-matter that mas too low in value to ship, but which it wag thought could be milled near the mine at a profit. The first milling-experiment consisted in the installation of Nissen stamps in conjunction with concentrating-tables and Frue vanners, but, as the ore from the upper workings contained most of its silver in the form of cerargyrite, this type of mill mas not successful. The proximity of the mine to the great copper-concentrating mills of Cananea and Moctezuma naturally made the influence of copper-milling ideas felt in the company's next instdlation. At considerable expense a stage-crushing concentrating-mill, with a capacity of 100 tons per day, was built. This mill was modeled along the lines of the most approved practice in copper-concentrators at that time, the main idea being that crushing by stages .in rolls was necessary in order to prevent losses from " sliming." Largely owing to the fact that, when the mill

Jan 1, 1913

By T. M. Broderick

INVESTIGATIONS into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attract-ing increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minne-sota (which spends about $80,000 annually on problems of the 'iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.1 Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was out-lined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert.

Jan 1, 1933