Search Documents

By Robert W. Thomas

During the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of interruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publications a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, therefore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.' From the scarcity of articles on the subject, it would seem that the concreting of haulage drifts is still far from being considered general

Jan 1, 1937

By Kongfang Feng, Fei Ruan, Zhiyu Liu, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jixu Wang, Jinyin Xie

"Mixing phenomena in smelting reduction furnaces with asymmetric side blowing were studied in this paper. Mixing phenomena in a smelting reduction furnace was represented as the mixing time by electrical conductivity measurements. Experiments were performed in a water model under various operating conditions to determine the effects of horizontal angle, radial angle, inserting depth, flow rate of the upper and the lower side nozzle, the included angle between the upper side nozzle, and the lower side nozzle on mixing phenomena in smelting reduction furnace. Comparing mixing time and mixing phenomena, the optimal conditions were obtained for an asymmetric side blowing process.IntroductionIn recent years, many countries have put forward development strategies for saving resources and environment-friendly, the development of various industries had to face its influence for resources and the environment .As we all know, the steel industry is a pillar industry of the global economy, in which ironmaking is an important part of it. In the modern ironmaking process, the blast furnace is regarded as the most important equipment and tool. But with the increasing scarcity of metallurgical coke resources and considering the environmental impact of such processes, metallurgists proposed the concept of smelting reduction. Smelting reduction processes to produce hot metal from iron ore and coal were being developed as a possible alternative to the traditional blast furnace. At present, a number of smelting reduction processes had been developed all over the world, they were mainly included COREX, HISMELT, FINEX, DIOS, etc."

Jan 1, 2012

By G. Ostberg

OXYGEN has frequently been considered responsible for phenomena in the metallurgy of cast iron which are not sufficiently explained by the presence of other elements. Oxygen and oxides have been regarded as critical factors, particularly for the solidification process, and specifically in the formation of graphite. However, the evidence for an influence of oxygen has mostly only been indirect or qualitative. Furthermore, quantitative data on the oxygen content of cast iron presented in the literature have often been less conclusive as being apparently determined with insufficient regard for the difficulties associated with the sampling and analysis. These problems, experimental and theoretical, have been studied in this investigation. An attempt is made to bring the views on the soluble amount of oxygen in cast iron on a level with the present understanding of the thermodynamics of these types of alloys. Although there are no experimental data on the complete multicomponent cast-iron alloys some conclusions have been drawn from investigations on simpler systems. The order of magnitude of the solubility of oxygen in cast iron is considered in the first part of the paper. The second part deals with the oxygen content actually present under practical conditions. First the possible sources of errors in sampling and analyzing methods are examined. Finally some observations on the oxygen and oxide content of malleable iron during the production process are made. THERMODYNAMICS OF OXYGEN SOLUBILITY When cast iron is saturated with oxygen the saturation phase is essentially carbon monoxide or silicon dioxide depending upon the composition of the iron, the temperature, and the rates of formation of the oxides.* The latter occurs accordiw to the O + C = CO, Kc0 - a COa J 20 + Si = SiO2, Activities are used here instead of weight pct concentrations, since activities are believed to show more sensitively the effects of the interaction of all the alloying elements. Calculations involving activities are, however, seriously hampered by lack of experimental data on the interactions between the components encountered in the multi component cast-iron system Fe-O-C-Si-Mn-P-S- and so on. In order to make an estimate of the oxygen solubility reason-

Jan 1, 1959

By W. B. Price

AT the New York meeting of the American Institute of Mining-and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."§ The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. PROTUBERANCES ON ADMIRALTY BRASS In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig.. 1a) and upon analysis was found to contain 66.66 percent. copper, 4.02 per cent. tin and .03 . per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and .01 per cent. lead. A sample of the shaggy-rough protuberances at the -very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had -revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation."

Jan 10, 1926

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By E. Yalçin, A. Ünal

In transitional mineralization, the sill of the underlying variogram is relatively easily estimated, but the estimation of the nugget effect may be more difficult. This study aims to determine for massive copper deposits just how sensitive the estimations of ore reserve, economic copper content, total net value, and ultimate pit limits are to the errors of estimation in the nugget effect of the spherical variogram model. A massive copper deposit which has a log-normal distribution and a spherical variogram was simulated on a rectangular grid using the turning bands method. By using the three dimensional random kriging method, the mean block grades were estimated at four different sampling densities. The ultimate pit-limits were determined by using the two-dimensional dynamic programming algorithm. To calculate the estimation errors, the values obtained by using the actual nugget effect and structured component values were deducted from the estimations obtained using the incorrect nugget effect and structured component values. For isotropic massive copper deposits, it was found that the ratio of the nugget effect to the structured component of the spherical variogram has no significant effect on either the block grades estimated by the kriging method or on the ultimate pit limits.

Jan 1, 1992

By P. Cowx

The carbothermic reduction of zinc oxide rich Electric Arc Furnace baghouse dust in the Tetronics transferred arc plasma furnace to produce a non-toxic slag and a metallic zinc product is described. In particular, the operation of the zinc splash condenser coupled to the plasma furnace is examined and the effect of process variables on zinc recovery is discussed.

Jan 1, 1990

By AIME AIME

IT is unlikely that any oil field has ever threatened the future course of the oil industry as does Kettleman today. It seems that nature has striven to outdo herself in combining in this field every possible factor conducive to a tremendous production of the petroleum product in greatest demand-gasoline. This field already has 13,700 acres of proved land and an oil zone of known thickness of 1400 ft. It has wells yielding several thousand barrels of oil of virtually motor fuel grade, together with millions of cubic feet of gas at almost unheard of pressures. The field would have been the. answer to an oil man's prayer in times of under-supply, but now it is the oil man's nightmare, for drilled in -the manner of most other fields and without regard to available markets for oil and gas, the greatest physical and economic losses in the his¬tory of the oil industry will result.

Jan 1, 1930

Contents

Jan 1, 1985

By E. V. Manlapig

"Some researchers postulate that the floatability of a particle in the streams of an industrial flotation circuit is a function of only its size and liberation properties. They do not discount the importance of reagent or surface contamination on particle floatability but assume that the reagent coverage or surface contamination of the particle surfaces is essentially uniform for particles of similar size and mineralogical properties when subjected to a particular chemical regime.In this paper, samples collected from batch tests performed on different streams of the Red Dog lead cleaning circuit have been characterised with respect to their size, mineral association and mineral surface exposure. An analysis of this data set indicates that particle recovery rate is significantly affected by mineralogical properties - in particular the degree of valuable mineral surface exposure.However, through the use of a nodal analysis technique developed by the authors, it can be concluded that particles with the same size and mineral composition do not all float with the same rate, but with a distribution of rates. The characteristics of this floatability distribution do not change during the flotation process. It is suspected that the particles within a size mineralogical class in this study have varying degrees of surface oxidation and that this results in varying particle flotation rates. Thus basing particle floatability on size and mineralogical effects, alone, in a flotation model is not always valid."

Jan 1, 2003

By K. Adham

Iron chloride pyrohydrolysis (ICP) is used as an efficient way to fix iron as an oxide, for sale as a by-product or for safe disposal. Iron chloride is reacted with water at elevated temperatures to yield iron oxide and hydrogen chloride. Both the steel industry and synthetic rutile producers make extensive use of ICP. Two technologies are available for ICP: fluidized bed (FB) and spray roaster (SR). Both technologies are energy intensive. Here, fluid beds and spray roasters are compared with respect to their fuel and electrical energy consumptions. Roaster size and oxide product characteristics are also considered. Process models are prepared, using the METSIM® software, and specific energy consumptions are compared. The results will help the industry decide which technology best suits its goals and at what energy cost.

Jan 1, 2006

By Michel David

"The usual complaint of mines is that grade does not match exploration expectations. Quite often, more tons are mined than expected but at a lower grade. This can be seen as dilution. Geostatistics can help predict which dilution can be expected both in terms of grade and tonnage for different mining methods.The usual vocabulary of geostatistics speaks of block distribution; block variance, size effect, information effect, all terms which say very little to the practitioner. In f act, all this can be rephrased in terms of dilution .In this paper, the following is presented - an example which shows how reserves change with the size of selection units and number of samples taken, and tables which show the dilution that are bound to happen when dealing with the commonly encountered log-normal distribution. Finally, the paper shows how grade tonnage computations should be made in the case of an arbitrary distribution. IntroductionGeostatistics progresses more and more rapidly if one judge s by the number and quality of papers published in Mathematical Geology or at APCOM meetings. More and more case studies describing successful applications are published (David et al., 1986)(Kwa and Mousset-Jones, 1987). It is estimated that more than 270/0 of the gold mines around the world use geostatistics. There is still, however, a lot of resistance from the remaining 73%. Geostatistics has more formulae and equations than it needs to reach year 2000. We will be well into the third millenium before all the models available now are actually used. The progress may come in the form of finding better ways to present known statistical results and getting away from the jargon of geostatisticians. One example may be in trying to explain how we can answer the most common plea of the mining industry: production grade is not what was expected in the feasibility study."

Jan 1, 1988

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By W. A. Forbes

PAGE Introductory............357 ReasoNs for Gas Cleaning.........358 First Methods of Separation of Dust.......359 Amount of Dust Produced by the Blast Furnaces of the United States Steel Corporation During 1912.....359 Dust Content in Blast-Furnace Gas.......360 Primary Cleaning. Dry Cleaning: General Remarks..........360 Braasert- Witting Whirler........362 Brassert Modifications of Brassert-Witting Whirler....363 Dyblie Whirler..........363 Remarks on Efficiency of Dry Cleaning......366 Wet Cleaning: Zschocke System..........367 Duquesne Tower..........367 Bian Gas Washer..........369 Final Cleaning. Wet Cleaning: Theisen Gas Washer.........371 Theisen Disintegrator Gas Washer.......372 Schwerz-Bayer Disintegrator Gas Washer..... 374 Fowler & Medley Vertical Gas Washer......376 Feld Gas Washer..........377 Reco Centrifugal Gas Washer........379 Sepulchre Gas Washer.........381 Dry Cleaning: Halberger-Beth Gas-Cleaning System......382 Smith.Bagley Gas-Cleaning System,......384 Howard Dust Separator.........387 Possible Separation of Dust by Electrical Precipitation ... 389 KapnOGraph............389 Methods of Determining DUst in Gas.......389 Advantages of Clean Gas.........393 Introductory. During the early stages of blast-furnace practice. the gas formed in the furnaces by the combustion of the coke used in smelting the ores was allowed to escape into the atmosphere. The light furnished

Jan 1, 1914

By Z. M. Zavodni, C. D. Broadbent

"Major rock slides in open-pit mines are rare, but they can develop in spite of sophisticated slope engineering design practice. Experience has shown that, except under high seismic load conditions, the serious slope instability condition is almost always accompanied by the gradual development of one or more tension cracks behind the slope crest, allowing for time-displacement monitoring. Continuous surface displacement measurements with attendant prompt analyses are usually adequate for the prediction of slope behaviour.This paper describes efforts that have been made to quantify parameters associated with slide movement, and compares the displacement records of several large-scale open-pit porphyry copper mine slope failures. Two principal failure stages are recognized in the typical slope failure leading to total collapse: (a) REGRESSIVE STAGE, during which the failure will re-stabilize if some disturbance external to the rock and structure is removed; and (b) PROGRESSIVE STAGE. during which the failure will gradually displace at an accelerating rate to the point of total collapse unless active control measures are taken. Over-all displacement records in both failure stages are apparently of simple exponential form. with a definite break occurring at the onset-of-failure point.Certain common empirical relationships are suggested for the large-scale slope failures analyzed in this study. Based on plots of displacement rate vs time prior to collapse, a semi quantitative empirical relationship is presented for failure collapse prediction. The comparison of historical slide displacement records furnishes the operating engineer with practical guidelines to estimate the characteristics of future large-scale slope failures."

Jan 1, 1980

By E. J. Horwood

The varying physical character and large extent of the Broken Hill lode necesarily involve the employment of a variety of underground methods. The lode had its origin in an extensive fault plane traversing metamorphosed schists conformably, as a rule, with their beds of stratification. The underground waters carrying minerals in solution deposited their contents in the original cavities formed by the faulting action, and in the enlargements of these cavities due to dynamic forces brought to bear on the rocks, more especially on the hanging-wall side of the fault. This deposition was supplemented by metasomatic replacement of a portion of the original rock contents by the argentiferous sulphides of lead and zinc which form the staple products of the district. Although the orebody is practically continuous throughout the mines, its width varies greatly, ranging from a few feet to about 350 ft. The widest portions occur in conjunction with huge folds in the inclosing country rock, almost exclusively on the hanging-wall side. The ore in these folds pitches to the south in the southern half of the field, and to the north in the northern half; there are, however, undulations in these ore channels evidently due to compression of the rocks in the direction of the channels. In the earlier days, before the orebodies had been opened up, vertical cross-sections across these bulges in the hanging wall gave the lode the appearance of the "saddle formation," so well exemplified at Bendigo in Victoria; but subsequent development of the ore channels has long since proved that the formations in the two districts are entirely different. The depth reached by the zone of complete oxidation of the sulphides varies from about 259 to 550 ft, from the original outcrop, while partial oxidation extends in places below the 1,000-ft. level. The result of oxidizing influences has been the production of ore of every grade of cohesive-ness, from that of dry sand to that of hard compact rock. The methods of mining followed in this field, and even in individual mines, are varied in accordance with the character of the ore. The general practice of the field is to sink vertical shafts, generally on the foot-

Jan 1, 1916

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed: The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation. This paper is an update of that which the authors prepared for the Infacon X ferro-alloys conference.

Jan 1, 2004

By AIME AIME

WAR undoubtedly accelerates metallurgical progress, although its most obvious effect is a tremendous waste of materials. The necessity for restrictions in normal uses of metals results in a search for substitutes or for enhanced properties that will make a limited supply last longer. An insatiable demand for more metal to be produced more quickly favors trial of new processes, new metallurgical tools, and new methods of fabrication. Greatest advance is made, of course, in practical physical and process metallurgy. Theoretical or fundamental research necessarily must take a secondary position, and is so regarded in this review. It is not that developments in theoretical physical metallurgy are lacking entirely, but, following the same trend noted in other countries as they entered war activities, attention in the U.S.A. has been shifted strongly to those developments having an immediate practical application.

Jan 1, 1943

By Robert B. Parsons

"It is easy to throw darts at government - and government often deserves to be a target. This month, Tax Notes examines tax legislation from a different angle, and sees some bright spots.The following article is based on a paper presented by the author at the International Gold Symposium in Rio de Janeiro in August 1989Introduction""No man's life, liberty, or property are safe while the Legislature is in session.”With one federal government, ten provincial governments, and two territorial governments all claiming to have constitutional rights to tax and otherwise regulate Canada's mining industry, and with each of these thirteen governments pursuing their respective rights with some vigor, government involvement in one way or another is an accepted way of life in the industry. While one's initial reaction to government involvement in an industry might be one of scepticism or fear, generally speaking the federal, provincial, and territorial governments in Canada tend to be pro-mining. They recognize the importance of the mining industry to Canada, especially in terms of job creation and exports. It is not surprising, then, to find that an array of valuable fiscal incentives are available to the industry through federal and provincial legislation.This paper summarizes the principal incentives that are inherent in Canada's tax legislation, as well as the Canadian Exploration Incentive Program. Although it is beyond the scope of this paper to deal with all of the incentives that are available, it is noted that various forms of federal or provincial assistance are also available outside of specific legislation, through negotiation with government departments. This latter type of assistance is generally directed toward helping with the cost of infrastructure such as roads or hydro lines, or Jess often toward loan guarantees or similar financing assistance."

Jan 1, 1990

By K. M. Rolls, R. M. Rose, H. B. Shukovsky

Studies of the phase structure, critical current density, and resistive critical magnetic field of a 45 pct Nb-55 pct Zr superconducting alloy after final-size heat treatments are reported in this paper. A combination of optical metallography, X-ray diffraction, and electrical-resistivity measurements were used to determine the phase structure. Superconductivity measurements, made with heat-treated wires, are correlated with microstructure. Although no quantitative relationship between microstructure and critical current density is found, it is shown that SINCE Kunzler1 as well as Berlincourt, Hake, and Leslie2 first described the high-field, high-current-density superconductivity of Nb-Zr alloys, it has be- the critical current density is highest when the microstructure is finely divided by fibering, coring, precipitation, or fine-scale phase dispersions. The resistive critical field is very sensitive to the compositions of the phases present. Since the alloy investigated here is near the maximum resistive critical field for the Nb-Zr system, any phase decomposition results in a lower H,. Elimination of the effects of cold work lowers H, also. A possible interpretation of the latter in terms of internal surface superconductivity is suggested. come apparent that the resistive critical field and the current-carrying capacity of such alloys are, in large measure, dependent on composition and processing. The resistive critical magnetic field (Hr) for low current densities has been found to increase progressively with zirconium content until a flat maximum is reached between 50 and 65 pet Zr.3 For any single composition, a characteristic maximum value of H, is attained by heavily cold-drawn wire.4 critical current density (J,) depends not only upon cold work but also, apparently, upon microstructure. Heat treatments of cold-worked wires generally

Jan 1, 1965