Search Documents

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li, Donald A. Bruce

"In-situ wet grab sampling and post-installation coring of soil-cement structures are typically carried out for Quality Control (QC) and Quality Assurance (QA) of deep mixing (DM) schemes. Wet grab sampling and testing is used to provide data to indicate that performance requirements are being met during production, in advance of coring, which typically occurs at 28 days or later, following installation. While unconfined compressive strength (UCS) tests from wet grab samples provide good production indicators, industry practice often requires that acceptance criteria of soil-cement structures be based on UCS results from representative core samples.This paper outlines the approach adopted for field sampling and QA/QC testing carried out in highly variable subsurface conditions at a site located in northern British Columbia (BC), focusing on postinstallation soil-cement coring and strength testing for an extensive deep mixing scheme. A discussion on suitable methods of coring soil-cement structures and appropriate selection of samples for testing that are representative of the in-situ soil-cement structures is provided. This paper also discusses the selection strategy adopted for verification of strength and modulus parameters used for design, providing spatial and time coverage, as well as the acceptance criteria implemented, and provides comparisons with published industry recommendations.BACKGROUNDAn extensive deep mixing ground improvement scheme was completed for the development of a Liquefied Natural Gas (LNG) Facility to be located in Bish Cove, BC, Canada. The deep mixing scheme was implemented to treat very weak native deposits in-situ to support two mechanically stabilized earth (MSE) walls up to 20 m (66 ft) high, and their associated bulk earthworks. Within the DM area, the subsurface conditions were highly variable, ranging from deep (up to 21 m (69 ft) thick) deposits of very soft to soft clayey silt to silty clay, overlying layers of dense to very dense gravelly sand to sand and gravel, to compact deposits of silty sand (up to 15 m (49 ft) thick), overlying dense sand and gravel. Bedrock was encountered beneath the granular deposits and generally comprised granodiorite with occasional andesite dykes."

Jan 1, 2015

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By Walter R. Storms, Jerry W. FAUST

This paper, which describes mining methods and costs at the Kearney zinc-lead mine, is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices, methods, and costs in varicus mining districts of the United States. The Kearney mine, which is owned by the New Mexico Consolidated Mining Co., a subsidiary of the Peru Mining Co. (Illinois Zinc), is situated a few miles southeast of the town of Hanover, in the northwest corner of sec. 27, T. 17 S., R. 12 W., in the Central Mining District, Grant County, N. Mex. (Figs. 1 and 2.) This report presents a brief history of the district, describes the geology, and outlines methods of prospecting and exploration, including eampling and estimation of tonnages and values. Development and mining methods are explained, and transportation, ventilation, drainage, safety measures, and organizatich are described. The wage scale and mining costs comprise the concluding sections of the report.

Jun 1, 1949

By Hsin H. Huang

Equilibrium calculational software programs can be effectively utilized to model the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation on extraction and recovery processes. Illustrative examples using the calculational program ST ABCAL for the creation of diagrams such as EwpH, activity or concentration-pH, and activity or concentration-EH are presented to demonstrate the fundamental characteristics of real hydrometallurgical mercury dissolution and recovery processes. An industrial application will include leaching of mercury from K 106 mercury sulfide waste and solution purification by iron cementation.

Jan 1, 2003

By R. L. Hopkins

The work described was performed to determine whether sulfur compounds of the thienothiophene class occur in crude oil. The presence or absence of various classes of sulfur compounds in crude oils is of interest and value to petroleum science. The Bureau of Mines, for the first time, identified hydro-carbon products of desulfurization that point directly to the identity of two individual thienothiophenes, namely 3-methylthieno[2,3-b]thiophene and 2-meth-ylthieno[3,2-b]thiophene, in Wasson, Texas, crude oil. These identifications, described in detail, were accomplished using microdesulfurization, mass spectrometry, and gas-liquid chromatography.

Jan 1, 1966

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By R Castedo, P Segarra, L M. López, J A. Sanchidrián, A P. Santos

The cylinder test allows us to determine the expansion of a copper cylinder by the detonation of an explosive charge inside. This test, originally designed for military explosives, has been adapted for industrial explosives with non-ideal behaviour. From data obtained with this test and known physical relationships, an analytical procedure has been developed to calculate the Jones-Wilkins-Lee (JWL) equation of state parameters for five ammonium nitrate/fuel oil (ANFO) and six emulsion-type explosives. A new radial wall expansion function is proposed considering a non-zero initial velocity with the consequent positive Gurney energy at unit relative volume. A set of equations is established to determine the JWL parameters, three of them obtained at the Chapman-Jouguet (CJ) point and the other three at different relative volumes. These equations, along with some constraints to ensure a physically sound solution, are solved for the JWL parameters by a non-linear least squares scheme. A 2D Lagrangian axisymmetric finite elements (FE) numerical model is developed for each tested explosive to validate the analytical results, in terms of expansion histories, with good agreement. This confirms that the set of conditions, constraints on the parameters and least squares calculation used constitute a robust methodology that fully captures the physics of the detonation products expansion involved in the cylinder test.CITATION:Castedo, R, Sanchidrián, J A, López, L M, Segarra, P and Santos, A P, 2015. Jones-Wilkins-Lee parameters for civil explosives, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Reliable predictions of the long-term water quality and water level fluctuations in a final void are vital if mine operators propose to decommission final voids in open cut mining operations. The catchments feeding final voids typically comprise a large proportion of coal placed or re-shaped spoil piles. Spoil piles from open cut coal mining operations have distinctive hydrological characteristics, which result in unique run-off behaviour. There is a need to understand the nature of spoil hydrology processes in order to predict the long-term hydrological behaviour and water quality responses of such systems. Preliminary estimates indicate that it may take 20 or more years for a void to flood. It is impractical for mine owners and operators to wait until long-term hydrological and water quality conditions have been established in a void, before reaching agreement with regulators about mine closure conditions. Reliable simulation of the long-term water quality and water level fluctuations in a void are therefore. The adoption of an agreed modelling approach and sharing of results from field data programs could result in the establishment of a database that could be used, with regulatory approval, for assigning parameter values, without the need for a specific data collection program for every individual void. Industry and regulators should agree on the model adopted for predicting post-closure behaviour of spoil/void systems. This will require reliable, robust methods for field data collection. This paper describes the field monitoring, data collection, model preparation and simulations undertaken over a three year period for Australian Coal Association Research Projects (ACARP) Project C7007. It presents the findings of that research, and provides comment on aspects of the project that were undertaken well and on aspects that could have been done better. Limited data is presented in this paper due to confidentiality arrangements with the relevant mine sites.

Jan 1, 2003

By B. E. Davis

A fundamental study of the mechanisms involved in the conditioning of coarse Florida phosphate has led to some interesting discoveries. Studies by the Bureau of Mines have shown that conditioning time and mixing intensity greatly affect the grades and recoveries of the phosphate minerals and quartz in the rougher concentrate. In particular, as the conditioning time or mixing intensity increased, the phosphate recovery remained constant while the amount of quartz floated decreased. This phenomenon is contrary to conventional wisdom and could lead to a more efficient coarse flotation circuit.

Jan 1, 1993

By P Hollings, J Holliday

Porphyry copper, gold and molybdenum deposits form in subduction-related settings in association with calc-alkalic or alkalic magmatism. Hydrothermal alteration assemblages are zoned, with potassic cores and propylitic haloes overlain by extensive domains of clay alteration and silicification (lithocaps). Copper sulfides, gold and molybdenite typically occur in veins or hydrothermal breccias, and less significantly as wall rock replacements. Epithermal deposits may form above or to the side of porphyry systems, and may be juxtaposed into the core of a porphyry deposit if rapid uplift and exhumation occur through the life of the magmatic-hydrothermal system. Volcanichydrothermal breccia pipes (ædiatremesÆ) commonly form late in the life of a porphyry system. They may contain clasts of porphyry-style mineralisation, and can host significant epithermal gold resources. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By V. J. Sikora, T. S. Hutchinson

This paper presents a method for making a water-rlrive ana1gsis without prior knowledge of aquifer geometry and uniformity using a standard desk calculator. Although it is necessary to know the initial oil in place to use this method, this is a minor limitation to the scope of (he method since in most reservoirs it is possible to obtain reasonably accurate volumetric oil-in-place estimates. An equation is developed which relates pressure at the water-oil contact to the water influx rate as a function of time by a factor called the resistance function. The resistance function introduces the composite effect of the aquifer geometry and flow resistance disrribution. It is pointed out that the characteristic shape of this function makes it possible to start with on approximation of the function and successively improve the approximation until the correct resistance function curve is obtained. In this fashion water-drive estimates can be made without the limitation of assuming simplifed aquifer shapes and flow distributions. This is the novel feature of this development. Methods are given for extrapolating the final curve to calculate future aquifer behavior. Equations are developed for adjusting the pressures and water influx rates where it appears that possible errors in these quantities make it difficult or impossible to obtain a useuble resistance function curve without this adjustment. Application of the pressure build-up analysis techiiique to estimate. some of the aquifer properties is also presented INTRODUCTION A great many oil pools are the result of oil accumulation in some type of trap in an otherwise large and continuous porous stratum. The void space of this stratum outside of the oil pool itself is filled with water or brine. In analyzing performance of the oil pool surrounded by this water aquifer, it is quite necessary. in most cases, to include behavior of the water. When the pressure at any point in a fluid system is lowered, such as by opening a well in an oil sand, fluids in the immediate neighborhood of this point will begin flowing towards this lower pressure sink. As pressure in this area drops due to flow towards the sink, fluids from farther out will start to flow towards the lower pressure. As more and more fluid is removed from the system, the distance from the sink or well within which flow is occurring will continually increase; that is, thc region of disturbance will grow. If some rigid boundary such as a fault is reached by the disturbance, this area will cease to grow; but if some movable boundary is reached, such as a water-oil contact, the area will grow on out into the water, although rate of growth may and almost always does change. The relation between amount of pressure drop and amount of fluid flowing at any point and at any time in an aquifer depends on such factors as compressibility and viscosity of the fluids, the porosity and permeability of the rock, geometry of the whole system and withdrawal rate or pressure drop. With these factors known, it is theoretically possible to calculate the pressure-flow behavior of the system, However, in practice true solutions to the problem are next to impossible due to complexity of reservoir systems. A number of approximate methods of solution have been developed based on various simplifying assumptions. One frequent assumption is that the water-oil contact can be located and equations defining oil reservoir and aquifer solved separately by assigning values to various parameters so as to match past pressure and production history. Usually the properties of the aquifer are not known, since few, if any, wells are drilled through the aquifer; but the water influx and the pressure at the reservoir boundary are known over some time. If it can now be assumed that the aquifer is circular, pie-shaped, or linear, and that it has uniform properties, it is possible to fit a theoretical dimensionless curve to the past aquifer performance history and therefore calculate future water drive. These theoretical curves are available in the literature,1,2,3 Of course, the assumption of uniform aquifer properties is almost always somewhat in error. Fortunately, however, moderate variations from the average have little effect on behavior of the system; and, hence, the best fit of a theoretical curve is frequently satisfactory. In other cases variations in aquifer properties and geometry are large enough that none of the available theoretical curves will give an acceptable fit of the data. In these cases, methods of fitting the data with various electrical analyzers have been developed.1,2' It is the purpose of this paper to present an approach

By Albert G. Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed.. Today, 'however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. DRILL TOOLS Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brinell hardness

Jan 1, 1935

By Jochen Petersen, Caroline Muzawazi

The technical feasibility of ammonia leaching of PGM bearing Platreef flotation concentrates was investigated as an alternative method for the recovery of base metals prior to precious metal recovery. The composition of the concentrates includes 2.02% Cu and 3.17% Ni, and the major base metal minerals are chalcopyrite and pentlandite. Optimal leaching conditions were initially established in shake flask experiments to be a solution containing 4 M NH4OH, 4 M (NH4)2CO3 and a pH range between 9 and 10. These were used as base case conditions in column and batch stirred tank reactor tests, where the effects of total ammonia concentration and operating temperature were explored further. At optimal conditions nearly 100% Cu and Ni extraction were obtained in the batch stirred tank reactor, and 95% Cu and 60% Ni extraction was obtained in columns. The activation energy for chalcopyrite and pentlandite was 36 kJ/mol and 16 kJ/mol, respectively, in both reactors, indicating different reaction pathways for the two minerals. Gas-liquid mass transfer appears to be the limiting reaction step in columns much more than in tanks, and the degree of ammonia loss to air is significant. This initial test work indicates the feasibility of using ammonia leaching for this and similar materials as an alternative route to conventional smelting and refining prior to PGM recovery, but a number of technical challenges still need to be overcome.

Jan 1, 2014

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Gary L. Seider, Dana A. Wesolek, Fred C. Schmednecht

"A new condominium project, The Atelier, developed by Pickus Companies located at the corner of Bryn Mawr and Sheridan in Chicago, IL required an earth retention system to protect the surrounding roads, alley, and existing neighboring apartment bui lding during its construction. Slurry Systems, Inc. (SSI) and Ground Engineering Consultants, Inc. designed the earth retention system using cantilevered sheet piling for three of the four sides: two sides bordering major streets and one side bordering an alley. For the fourth side, which borders an existing occupied brick building, a combination of sheet pil ing and AB. CHANCE® helical screw piers were used. SSI was actively involved in the review process of its earth retention system with the City of Chicago and quickly learned that there was no specific code for hel ical piers/anchors. (It appears that this is the case with most metropolitan cities throughout the United States). Consequently, the approval of underpinning for this project became the critical path, as much testing, calculations, meetings, and other details were required prior to its approval.SSI and AB. CHANCE® recognized that this process for underpinning approval must be seen by other contractors/suppliers who wish to use helical piers/anchors in the City of Chicago. Consequently, this project served as an opportunity to work with the City of Chicago and the City's Building Code Committee in furthering the development of the Helical Piers/Anchors Code, Section 1814. INTRODUCTION - HELICAL PIERSDefinition. A helical pier or anchor consists of one or more helix-shaped steel bearing plate(s) attached to a central steel stem (solid bar or pipe), which is installed by rotating or ""torquing"" into the ground. Each helix is attached near the tip, is circular in plan , and is formed into a screw thread with a defined pitch. Helical piers/anchors are pre-fabricated and can derive their load-carrying capacity through both end bearing and skin friction. The helical piers/anchors can be augmented with grout."

Jan 1, 2005

By Bert Taylor

"The Mining concessions of Quemont Mining Corporation, Limited, are located at 48°16'N latitude, 79°00'W longitude, in Rouyn township, northwestern Quebec. Six hundred and forty acres in area, they lie directly north of, and contiguous to, the Horne mine of Noranda Mines Limited. The north arm of Osisko Lake covers a large area of the southern part of the property. The orebodies lie below the Jake with one body extending through to the bedrock surface.The property was staked in 1922, and was originally known as the Murray Claims. The group attracted interest from numerous exploration companies because of the proximity of the Noranda orebodies.The United Verde Extension Company, of Arizona, optioned the claims in 1926. They sank a shaft to a depth of 235 feet, at a short distance from the Noranda boundary. From a level established at a depth of 215 feet they completed 3000 feet of exploratory driving from which 6000 feet of diamond drilling was done. Only a small body of siliceous gold ore was found before they dropped their ·option.In 1928, The Mining Corporation of Canada purchased a 90 per cent interest in the property. An operating company, later named Quemont Mining Corporation, was formed. An electrical survey was carried out on a portion of the property, followed by deepening of the shaft to 922 feet. Levels were established at 500 and 900 feet, and 4,800 feet of driving and more than 3000 feet of diamond drilling were carried out from them.Geological knowledge at that time recognized that a major break, the Horne Creek fault, lay not far inside the south boundary. Striking north 80 degrees east, the fault dipped south at 85 degrees. The rock on the north side of the fault was massive rhyolite; to the south, meta-diabase and a little rhyolite. A left-handed movement was indicated by a 600-foot offset on a north striking diabase dyke. The small body of siliceous gold ore, referred to previously, was confined to the 215 level."

Jan 1, 1949

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By M. Misra

The prediction and assessment of the reactivity of acid mine tailings has been a subject of numerous studies. The conventional approaches such as sulfur content, pH, net acid generating capacity and conductivity are used for assessing reactivity of the tailings. In this paper a new non-invasive Impedance Spectroscopy (IS) technique is used for the determination of reactivity and acid mine potential of tailings. This technique is also used to establish the long term stability and leaching propensity of the tailings agglomerated with alkaline binders.

Jan 1, 1994

By G. Cartaud, F. Osmond

We have already devoted two previous memoirs to this question. In the firstL we collated and discussed the existing literature on the subject; in the second: we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allo-tropic states of iron—a, stable below A2; , stable between A2 and A3; and , stable above A3—all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, and did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier mas even led to think from some of our results that r-iron could very well be a rhom-bohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Jan 1, 1907

By H. OSBORG

THE patent literature of alloys for the last two decades or so indicates that the number of liatents referring to smaller and smaller percentages of essential alloying constituents is on the increase, whereas the number of patents relating to considerable percentages of alloying additions becomes smaller. The claims regarding physical properties indicate consistently higher and more rigid values and show the possibility of modifying the physical properties by only slight changes in the percentage of minor constituents or by applying different methods - of treatment. Alloys of the same base have been made suitable for a number of different applications by intelligently and rigid- ly controlling their composition, melting, casting, working, and heat-treatments. Other trends indicated in the development of modern alloys are higher corrosion resistance, higher fatigue limits, and "stability" in volume.

Jan 1, 1937