Search Documents

Novel techniques were developed to obtain samples from and make measurements in the shaft of the flash furnace at the Kalgoorlie Nickel Smelter. The data obtained was used to validate mathematical models of the burners and the reaction shaft. Particle, gas and wall temperatures were measured along with the oxygen potential of the molten particles. Collected particles were characterised by sizing, chemical analysis and optical microscopy. The region of the shaft immediately beneath the burner where the rate of change was most rapid received special attention.

Jan 1, 1993

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By P. Mottahed, E. K. S. Passaris, J. Q. Ran

"The jointed roof of underground mine openings in stratified rock can be analyzed in terms of a voussoir beam. Because of the essential indeterminacy of the structure, previous attempts of theoretically solving the equilibrium equation have been unsuccessful. Numericalanalysisby the finite element method taking the geometrical and joint non-linearity into consideration combined with the experimental method has been adopted to study the performance isopara of the voussoir beam. Deformation and failure mechanism is analyzed in relation to the failure modes. Equations are proposed to estimate the elastic buckling strength and the crushing strength of the voussoir beam and to verify the failure mode of shear sliding. For application of the mechanism of the voussoir beam in mining operations, methods are described to predict the stability of a jointed roof and to design the dimensions of mining openings.IntroductionThe roof stability of an underground mine opening has direct effects on the selection of support methods, opening dimensions and, more importantly, on the safety of mining personnel. The prediction of the roof stability can be of importance in the design of a mining method and in mining operations. The jointed roof of mine openings in stratified rock can be stable under transverse load depending on the roof geometry and properties of the roof material and joints. The stability of this type of roof can be analyzed in terms of a voussoir beam which was introduced by Evans (1941) to study the strength of underground strata. Brady and Brown (1985) analyzed the voussoir beam and suggested that the mechanism of the voussoir beam could be used in the design of underground mine openings in stratified rock instead of the traditional continuous beam theory."

Jan 1, 1993

By Robert J-M Ethier

"Sequential blasting has been introduced at Mines Gaspe to reduce the harmful effects associated with the instantaneously primed blasting method. Three stages of modifications had been tried to improve this method: trials of a rectangular pattern instead of the square one, trials of lengthened hole collars at the perimeter of the blast and trials of increased inter-row delay intervals from 35 to 50 ms. Results showed that improvements to the instantaneously primed blasting method were limited by the probability of increasing the number of bootlegs.Doing these modifications allowed the definition of a general approach to improvements before the sequential blasting method was introduced. This general approach included: planning of the mining sequence, following up on the drilling, loading and tying-in of each blast, compiling and evaluating blast results, comparing results from one bench to the other and moving along with one change at a time. This approach has permitted the successful introduction of the sequential blasting method in two steps: trials of blast by rows of delayed holes and trials of hole-by-hole blasts. The optimum result has been analyzed by high-speed camera and by computer blast simulations, The actual optimum sequential blast is obtained with a CORDLINE priming system using period 15, permitted in a large drilling pattern, with an intersequences delay interval of 230 ms and an inner-sequences delay interval of 50 ms.While these modifications were being introduced, a careful study of the drilling and blasting costs was made, which showed a sharp reduction of drilling cost per tonne. Even though there was an increased use of packaged slurry the blasting cost per tonne also dropped. The reduction in cost per tonne was explained by the fact that the average energy factor was maintained while the blasting pattern was expanded.The sequential blasting method, successfully introduced at Mines Gaspe, permits blasts of better quality, reduces the drilling requirements by more than 30% and helps to achieve improved productivity while minimizing costs."

Jan 1, 1984

By D. M. Ward, J. H. Ahrens

"The Fond-du-Lac uranium deposit was delineated primarily by percussion drilling and a small program of diamond drilling. Drillcore samples from three diamond drill holes as well as digitized gamma logs from percussion and diamond drill holes were utilized to define and implement an algorithm for the conversion of gamma-log data to equivalent-grade data. The procedures and detailed analysis for the provision of assay data for uranium reserve estimation are documented.IntroductionThe Fond-du-Lac uranium deposit is on the south shore of Lake Athabasca, approximately 2 km southeast o f Fond-du-Lac , northern Saskatchewan. It is on the northern rim o f the Athabasca sandstone basin.A train of mineralized glacial erratics was discovered in 1967 by Farnok, Limited by means of a helicopter-borne radiometric survey. In 1969, a program of diamond drilling by Famok was successful in locating in-situ mineralization in the Athabasca sandstone at the apex of the mineralized boulder train. Since 1974, exploration and development work have been performed under a joint-venture agreement between Eldorado Nuclear Limited and Famok Limited, with Eldorado acting as operator.From the discovery drill hole to the development of the gamma-log to equivalent-grade con version algorithm, the deposit had been tested by a total of 222 drill holes, 210 of which were percussion holes and 12 of which were diamond drill holes. The holes are generally vertical and collared at 10-metre centres on fences spaced 20 metres apart. The deposit is approximately 390 metres long, 10 to 40 metres wide and up to 45 metres deep, and is generally confined to the Athabasca sandstone. Uranium occurs as pitchblende, coffinite and uraniferou s goethite."

Jan 1, 1983

By L. Harris

El presente trabajo describe el proceso, organización, costo de proyecto e inicios de operaciones de la minera Yanacocha, ubicada al norte de la ciudad de Cajamarca. Su principal producto es el cobre. Dada la ocurrencia de óxidos que se inicia en la superficie y extiende a poca profundidad, se utiliza el tajo abierto como el método más adecuado para la extracción de mineral. Asimismo el estudio describe el plan de minado, equipamiento, descripción del proceso y el estudio de impacto ambiental para la protección del medio ambiente en Yanacocha.

Nov 24, 1993

By M. M. Hajdasinki

A project's rates of return (RORs)1, be it the internal rates return (IRRs) or one of the many IRR surrogates, frequently needs to be approximated. The success and efficiency an ROR- approximation procedure depend on the quality the approximation-initiating parameters, such as bounds or seed values (guesses). The existing approximation procedures commonly use bounds and guesses suggested by intuition rather than supported by mathematical considerations. This paper presents three mathematically founded ROR-bounding and eleven ROR-guessing approaches and examines their suitability by using examples of typical project cash-flowpatterns (CFPs). The calculated bounds and guesses not only improve the approximation efficiency, but also allow the process of the ROR discovery to be automated, thereby making it more convenient and reliable.

Jan 1, 1999

By S. D. Maksimovic

The Bureau of Mines identified and evaluated major sources of quartz dust during overburden drilling at a surface coal mine, The relative contribution of each source to the total dust hazard was estimated, using personal gravimetric and instantaneous dust-sampling devices. No attempt was made to determine actual dust generation rates. The major sources of dust at the drill rig during dry drilling opera-tions were the collector dump, drill shroud leakage, and drill stem seal leakage, These sources contributed 90 pct of the respirable dust and 89 pet of the respirable quartz dust generated during drilling, The collector dump cycle (21.6 pct of total drilling time) accounted for 38 pct of the respirable dust and 41 pct of the respirable quartz dust, with peak dust concentrations reaching 68 mg/m3. Shroud and drill stem leakage contributed 28 and 24 pct of the respirable dust and 32 and 16 pct of the respirable quartz dust, respectively. A dragline and second drill rig contributed the remaining 10 pct of dust and 11 pct of quartz dust. Gravimetric dust samples collected inside the drill cab and outside, near the cab door, averaged 1.65 and 1.43 mg/m3, respectively, with 6 pct respirable quartz.

Jan 1, 1985

Where vertical or near vertical faces are required in open excavations in soils and rocks, some form of stabilization of the 'cut is often necessary. Stressed anchors either alone or in combination with steel, timber or concrete-lagging are often an economical and versatile means of providing support. Stressed anchors are also-a very economical means of anchoring a wide range of structures such as dams, cranes, transmission towers, retaining walls, spillway aprons, bridge piers; and - stacks. The anchors need not be stressed always on installation.other than to proof load them. A number of examples illustrate some of-the more practical aspects of.the design and construction techniques used. No new methods of design or construction are involved, but merely some consolidation of the engineering design, soil and rock mechanics,thinking applied to the stressed anchor tech- nique.

Jan 1, 1971

By R. J. Blackwell, J. R. Rayne, W. M. Terry

This paper presents results of an experimental investigation of factors that control the efficiency with which oil is displaced from porous media by a miscible fluid. The study was made to elucidate the relevant processes both on microscopic level (within individual or between neighboring pore spaces) and on macroscopic level (within a large sand body). Mixing of miscible fluids on the microscopic level was studied in sand-packed tubes. It was found that molecular diffusion is the dominant dispersion mechanism for reservoir conditions of rate, length and pore sizes. Macroscopic channeling was studied for various mobility ratios in reservoir mode1s scaled to relate viscous, gravitational, and diffusional forces. The formation of channels was due to viscous firzgering, gravity segregation and variations in permeability. With adverse mobility ratios, it was found for reservoirs of realistic widths that diffusion will not be effective in preventing the formation and growth of fingers, even in homogeneous sands. At sufficiently low rates channeling was eliminated by gravity segregation in tilted reservoirs. The dependence of recovery on mobility ratio, length-to-width ratio, flow rate and angle of dip is presented. INTRODUCTION Oil recovery by solvent flooding is finding increasing application in the field. While the process promises high recoveries from the region swept by solvent, under adverse conditions only a small fraction of the reservoir volume may be swept at the time solvent breaks through to the producing well. Further, the high cost of the solvent encourages its use only as a bank whose size must be kept at a minimum. Thus, two important questions arise: (1) what fraction of the reservoir can be swept, practically, by solvent? and (2) what is the minimum size solvent bank that can be used to carry out the displacement? The answers to these questions require knowledge of both macroscopic channeling processes and microscopic mixing processes. The studies described here were carried out to gain this knowledge. Microscopic mechanisms which cause mixing will be discussed first, because an understanding of these mechanisms is necessary for proper interpretation of the experimental work on channeling described later. INVESTIGATION OF MICROSCOPIC DISPLACEMENT PHENOMENA FOR MISCIBLE FLUIDS The questions to be resolved concerning microscopic displacement behavior are: (1) how much mixing occurs between oil and solvent in the direction of flow? and (2) does the solvent completely flush the oil from the pore spaces in the region invaded by solvent? The classic work of Sir Geoffrey Taylor' and its extension by Aris2 have shown that it is possible from theory to describe the amount of mixing in single straight capillaries when solvent displaces a fluid of equal viscosity and equal density. Aris showed that the lengths of the mixing zones, 81, corresponding to the 10 per cent and 90 per cent concentration levels of the solvent can be calculated from the formula, 81 = 3.62 \/Kt, .........(1) where 8l is the length of the mixing zone, cm; t is the time, sec; and K is the effective dispersion coefficient, cm2/sec, given by K/D = 1 + (1/48) (au/D)2......(2) where a is the radius of the capillary, cm; D is the molecular diffusivity, cm2/sec; u is the average velocity

By Henry Brehaut

"It is difficult to know how much environmental information is absorbed by those in a position to put it to use. The following information may seem like ""old stuff"" to those whose companies are taking steps to improve their environmental performance. This paper is directed in particular to those people who are interested in determining what further changes are required to make improvements as concerned environment citizens.IntroductionUntil recently, the author was comfortable with the fact that none of the operations for which he was responsible had any environmental charges against them. It was not until one of his operations was charged with non-compliance that the author discovered due diligence as a way to avoid a second charge, and when an unfortunate spill occurred at another operation, the meaning of risk prevention was learned. Knowledge was gained step by step to the point where finally environmental information is being heeded, rather than waiting to learn from sad experience. With the appreciation of what it takes to do a good environmental job, comes an understanding of the challenge that lies ahead, and the fact that there is a lot to learn.At a recent environmental gathering, comments from the participants varied considerably. Some just didn't understand why government was being so unreasonable, while at the other end of the spectrum one individual whose company was well along the path to becoming a good environmental citizen remarked that it was all very basic. What was immediately understandable to one went right over the heads of others, indicating the different stages that have been attained in the acceptance of environmental responsibilities."

Jan 1, 1991

By Sven Reutzel

Investigations show that Co-based melts embedded by glass flux in a crucible can be under- cooled nearly as strong as samples processed containerlessly by electromagnetic levitation. This allows to measure magnetic susceptibility on undercooled melts while combining the use of a Faraday-balance and undercooling technique. The magnetic susceptibility of Co and Co-based alloys (such as Co-Pd and Co-Cu) is investigated as a function of temperature from superheated to undercooled state. This is done by measuring the change of magnetic force F, on a sample in a constant magnetic field Bo and an additional gradient field by means of a Faraday-balance. When liquid Co-based alloys are undercooled the magnetisation steeply rises if temperature approaches the Curie temperature. The magnetisation is measured for some Co-based alloys in liquid state as a function of alloy system and its concentration. The results show that the magnetic susceptibility of the liquid undercooled samples follows a Curie-Weiss behaviour, from which Curie temperature and magnetic moments for the liquid state are inferred.

Jan 1, 2002

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By Reno Sales

THE present-day application of geological knowledge to mine opera-tions owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contem-plated. And finally, out of this situation there developed the inde-pendent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1934

By AIME AIME

FOUR separate groups of conveyors are installed in the Morenci Reduction Works as follows: (1) Ore-handling conveyors from the primary crushing plant to the coarse ore bin, from the coarse-ore bin to the secondary crushing plant, and from the secondary crushing plant to the ore bin in the concentrator plant. (2) Conveyors in the mill section of the concentrator plant. (3) Conveyors handling concentrate from the filter plant to the bedding plant, and from this plant to the smelter. (4) Conveyors handling flux and custom ore in the smelter crushing plant and to the bin at the bedding plant.

Jan 1, 1942

By Kal V. S. Sastry

Conventional iron ore balling circuits exhibit undesirable surging behavior which is known to result from uncontrolled occurrence of the mechanisms of nucleation, coalescence and layering. This study was undertaken to investigate the mechanism of pellet growth by layering. Several laboratory experiments have been carried out to delineate the effect of feed moisture content and feed quantity. This paper presents an analysis of the experimental results and a simple model to describe the layering process.

Jan 1, 1993

By MINE SAFETY BOARD

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions . In recent years these questions have tended to increase with the use of mechanical appliances . Twenty- five years ago electricity had hardly been used in mines . To - day there is practically no other means of transmitting energy employed in American mines , except in metal mines where compressed air is used for drilling and small portable hoists . In coal mines there has been a great increase in mechanization and a tendency to concentrate the mining operation , which has resulted in attendant difficulties of ventilation and intensified the danger of coal - dust in bituminous and subbituminous mines . The answers to the questions which arise are not always obvious , as is shown by the fact that even able , experienced men differ in their opinions of the best way to overcome a particular mining hazard . The difficulty of solving the problems is also demonstrated by the varying provisions in mine safety rules , both in official regulations and in the rules of those mining companies who are endeavoring to do more than follow the letter of the law . Such differences of opinion on the best way of meeting a difficult situation are often found within the same mining organization , and so it has been in the Bureau of Mines .

Nov 1, 1929

By Michael D. Fenton

Bauxite resources were primarily in Africa, Asia, Oceania, and South America. Only five countries combined, Australia, Brazil, Guinea, India, and Jamaica, contained most of the total world reserves available for extraction under current economic conditions and accounted for nearly 80 % of world production of bauxite. World bauxite and alumina production declined and prices for smelter-grade alumina remained below the $200/mt level during 1993 because of growing aluminum inventories on international markets and declining worldwide demand. The United States imported bauxite primarily from Australia, Brazil, Guinea, and Jamaica. U.S. alumina plant capacity remained essentially unchanged throughout 1993, but apparent capacity utilization decreased by the close of 1993. Chromium Most of the world's known resources and reserves of chromite are located in India, Kazakhstan, South Africa, and Zimbabwe. India, Kazakhstan, and South Africa accounted for 73 % of world production of chromite. The two largest producers of chromite, Kazakhstan and South Africa, were in the process of major economic and political change during 1993. South Africa's production and exports of chromite continued to fall during 1993, because of weak international demand and a flood of cheap metal from the former U.S.S.R. and China into world markets. Despite a significant increase in production, South Africa's ferrochrome producers continued to operate below capacity in 1993. Prior o the dissolution of the U.S.S.R., Kazakhstan was a major internal supplier of chromite ore to the U.S.S.R. consumer, but subsequent decline in demand led to a downward trend of chromite production in Kazakhstan and increasing exports to Europe during 1992 and 1993. The United States consumed, about 10% of world chromite ore production in various forms of imported materials. The United States imported nearly one-half of its required chromium contained in chromite ore and chromium ferroalloys and metal from South Africa; the remainder was from the minor producers Turkey, Yugoslavia, Zimbabwe, and others.

Jan 1, 1995

By D. Cummins

This Information Circular presents a brief history of the lead-acid battery and describes ways to prevent serious injury from battery explosions when servicing and charging lead-acid batteries, particularly in the surface mining industry. The Mining Safety and Health Administration (MSHA), U.S. Consumer Product Safety Commission, battery manufacturers, and the mining industry have all contributed information as well as recommendations for injury-free handling for this report.

Jan 1, 1980