Search Documents

By W. Yang, R. Rajasingam, K. Mohanarangam

"Copper Electrowinning (EW) is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. The process setups up a complex flow pattern within the cell as it is subjected to varying density gradients due to the deposition process along with oxygen bubble driven flow. It is a necessity to understand and quantify the flow behaviour within these cells in order to maintain the production of highest grade copper. In fact, the oxygen bubbles originating from the process is responsible for the generation of acid mist which is a designated as a carcinogen a major health hazard around EW tank houses. Hydrodynamic assessment of the process has so far been restricted to simple mass balances and some limited numerical modelling. All the models are based on assumed boundary conditions which has not so far been verified by any real-time physical measurement. This apparent gap has led to models which could not be directly used to track process changes or troubleshoot problems in EW tank houses. In order to address this gap, CSIRO has established a full size (width and height) transparent cell capable of simulating plant operating conditions (across the range currently used). With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables (current density, flow rate, temperature, etc.) independently and their effect of bubble size, bubble velocity, gas hold-up as well as acid mist generation and its size. In order to address safety concerns in tank houses around acid mist early results outlining the factors contributing to its generation as well as the effect of various barriers to mitigate acid mist is outlined below.INTRODUCTIONA significant part of today’s copper production is through hydrometallurgical route which predominantly involves leaching, Solvent eXtraction (SX) followed by ElectroWinning (EW). Producing copper using this approach have shown to be environmentally friendly (Dresher, 2001) compared to the traditional smelting process. EW is the final step in the production of LME grade copper using the hydrometallurgy route. The electro-chemical process involves the use of a lead anode (Pb-Sn-Ca) and a stainless steel cathode to produce copper sheets using the copper rich electrolyte from the SX process and with the applications of direct current to the electrodes. This electro-chemical reaction results in the deposition of copper ions on the cathode with oxygen released from the anode as a by-product. Hydrodynamically, the oxygen bubbles create a bubble driven flow within the EW tanks with the surrounding electrolyte. A direct result of this could be seen from the quality of the copper deposited on the cathode. Most of the copper plates produced from the traditional tank houses have a rough texture at its bottom one-third while the top two-thirds have a smooth finish with a finer grain structure."

Jan 1, 2016

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

By Kevin Peacocke

The future of Gravity ? Primary mineral recovery ? Enhancement of existing process efficiency ? Pre-Concentration ? Alternative? or ?New? production

Jan 1, 2006

By J Ranford, A Harris, K Laughton

The Angas Zinc Mine (Angas) is a poly-metallic, underground mine in the Adelaide Hills that has been developed through arguably one of the most volatile financial time periods in living memory. From boom times during the commencement of the project, the global financial crisis (GFC) through the stabilisation of the operating period and then a subdued capital market for the period where mine life extension was targeted, the financial environment has always presented a different set of challenges. Indeed even the Underground Operators’ Conferences that have been held across the span of the project allude to these changes: ‘Boom and Beyond’, Launceston (2008); ‘Safe, Innovative and Sustainable’, Canberra (2011) and ‘Managing the Margin’ in Adelaide (2014).Angas gives a rare opportunity to see the entire life-of-mine of a project and its economic performance within a relatively short time frame. Angas, owned and operated by Terramin Australia Ltd (Terramin), will have undergone resource estimation drill out, feasibility study, permitting, commissioning, operating and completion and rehabilitation all within a period of approximately ten years. A number of sensitivities of the project were tested, particularly in the bankable feasibility study (BFS) stage and the aim of this paper is to identify the factors that impacted the operations profitability the most, whether they were identified preproduction or not. The key sensitivities assessed in the BFS were typical of similar studies, including operating costs, metal recoveries, capital costs, zinc prices, lead prices and exchange rates. The manner in which these sensitivities presented themselves in real life were not as anticipated and modelled in the feasibility study and were also heavily impacted by technical challenges.CITATION:Harris, A, Laughton, K and Ranford, J, 2014. Feasibility to mine completion – the real impacts on project economics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 99–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Jiann-Yang Hwang

A study on microwave assisted chalcocite leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick mineral slurries (50-100 g/l). The leaching media is a mixed solution of CuCL2 and NaCL The investigation included the effect of leaching temperature, quantities of the minerals per unit slurry volume as well as the initial concentration of cupric ions were investigated. The results were discussed and compared with that using conventional leaching method.

Jan 1, 2003

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By Oliver Bowles

[In an endeavor to promote greater efficiency in the lime industry, the United States Bureau of Mines is preparing a series of preliminary reports dealing with particular problems of the industry. Through the circulation of these reports, it is hoped that sufficient interest may develop among lime-plant operators to prompt them to discuss with the bureau their our experiences with these problems. By such an interchange of ideas, it is believed that conclusion may be reached which will be of practical benefit to try entire industry. The first report, "Stripping problems it Limestone quarries of the Shenondoah Valley", Serial No. 2401, was issued during October, 1922. This report t is the second of the series. It is hoped that may operators will contribute additions to the information now at hand.]

Jan 1, 1922

By Owen W. Terry

During the summer of 1943 the Bureau of Mines conducted an investigation and program of churn drilling on the McIlhon and adjoining Pearson land in the Mineral Point district of Iowa County, Wis. Sixteen holes, aggregating 1,570 feet .of bore, were completed. The work was undertaken as part of a general investigation of the zinc-and lead-producing area of southwestern Wisconsin at a time when great effort was being made to increase the production of Metals important to the war program. The Bureau's drilling program supplemented a previous drilling pro-gram conducted by the Vinegar Hill Zinc Co., and demonstrated the presence of a strongly mineralized zone at relatively shallow depths.

Jan 1, 1948

By Henry M. Howe

Jan 1, 1908

Column flotation cells continue to gain acceptance in the coal industry for the treatment of high-ash streams containing clay slimes. Unfortunately, some industrial installations have failed to meet expectations due to improper scale-up, incorrect operation and poor ancillary circuit design. To overcome these problems, case studies have been conducted to fully define the capabilities of column cells for coal applications. These data have been used to develop generic engineering guidelines for column circuit design and operation. An economic analysis has also been conducted to illustrate the importance of key capital cost considerations. These analyses indicate that column cells are significantly more expensive than conventional machines, although this difference can be greatly reduced through the installation of very large-diameter columns.

Jan 1, 1999

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By T. F. Baily

During the period of the war, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted. at Canton, Ohio, in

Jan 1, 1930

By Jiang Fan, Wang Haigang

"The three-dimensional complex multiphase turbulent flow in U-beam separators was simulated using the Reynolds stress equation models (RSM). To account for the effect of the stochastic characteristic of the instantaneous gas velocity on the particles, the improved Lagrangian stochastic model based on the Reynolds stress model for gas phase was adopted, which attributed to the successful prediction of the turbulence anisotropy and particle crossing trajectories effects. The interaction between the particles was also considered using the HardSphere model. To treat the particle-wall collision, the influence of the roughness of the wall on the motion of the solid particles was taken into consideration by imposing random collision angles. The result from this study not only shows the dynamic characteristics of the multiphase flow- in the separators, but also gives the relationship among the efficiency, structure and pressure losses of the separator.IntroductionCirculating fluidized bed (CFB) combustion is one of the most promising clean coal techniques. A main feature of CFB boilers is the un-delayed recycle of solid, coal and sorbant particulate, in an external loop. Separator, which is required to separate the solid particle from the flue-gas leaving the reactor of CFB, plays an importance role in the external solids recycle loop. It affects the combustion of CFB system greatly. Presently cyclone is the most commonly used as separators for CFB system and other chemical industrial processes. It provides high level of separation for CFB system for fine particles. However it suffers from some inherent disadvantages. It's volume and size is huge. Moreover, it is difficult to design and install when the CFB workload rises. The application of U-beam separators instead of hot cyclone separators in CFB boilers has many advantages. Publications indicate proposals or successful use of Ubeam separators in Swedenr11, USA 21, Russia r3land China [4]• But it is not possible to find results in the literature of detailed investigations of this new. type of separators or recommendations on the choice and calculation of an optimal design. For this reason, numerical simulation for the three-dimensional gas-particle two-phase flows with several rows of vertical U-beam elements, local in the chess order and blocking a way of outgoing from a CFB boilers dusted gases was carried out in this study."

Jan 1, 2004

By P. L. Woolf

Oil was successfully injected into the tuyeres of the Bureau of Mines experimental blast furnace. Determinations were made for the minimum oil addition necessary to permit the maximum available blast temperature of 2,250° F. and the maximum oil rates at blast temperatures of 1,900°, 2,000°, and 2,100° F. From these tests, the upper and lower levels of high-temperature heat input, which limit the smoothly operating furnace, were established. Substantial coke saving was realized with maximum oil injection. Oil-to-coke replacement ratios have been calculated for various conditions, and oil is compared with natural gas and moisture in somewhat general terms. A study of the effect of variations in slag volume and basicity on the sulfur content of the metal at high sulfur loads was made.

Jan 1, 1963

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received little study on the part of wire mills, particularly those that have commenced operations in the last few years. Two Types of Defects One type of defect is generally known in this country as "check marks;" in Europe it is termed "crowfeet" (Fig. 1). This defect occurs in the surface of the copper wire, in the form of V&apos;s, which are always

Jan 1, 1930

By X. W. Lv

The intelligent recognizing and processing system for sinter ore mineragraphy make a great convenience of recognition and measurement. Specially, it?s critical important for a successful intelligent system to extract the minerals? feature accurately and sufficiently. Reflection index, as the crucial feature of mineral, is calculated by the theoretical calculating model of index based on the principle of imaging color models. In gray histogram of minerals? micrograph, the peaks? positions represent the information about mineral categories and contents. The relationships of different minerals? peak-positions in curve of gray histogram were got by using the peak-find model of gray histogram and calculating model of reflection index. These two models which can be regard as the method of feature extraction for minerals? photomicrograph also lay a good foundation for the artificial intelligent system of recognition and processing in sinter ore.

Jan 1, 2014

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By J. E. Klein

Bench scale tests using a stack of ten whole SAES St909 pellets, 6 grams, to crack methane have been completed with pure methane feed. Test conditions ranged from 600 to 800°C at 101 kPa (760 ton) with a methane feed rate of ten sccm. Methane reformation tests, test where hydrogen was passed through a St909 bed after cracking methane, were performed to determine if and how much methane can be generated under "reformation" conditions. Phase structure determinations of St909, composed of a ZrMnFe alloy with aluminum used as a pellet binder, after methane cracking were complicated by the number of materials that can be formed by the elements in the St909 and the carbon from methane cracking. It was determined that the aluminum not only alloys with the Zr, Mn, and Fe in the St909 alloy, but also forms aluminum transition metal carbides in addition to ZrC as the carbon content and the temperature of the St909 increases. Some A14C3 was also found in some pellets. Passing hydrogen over St909 pellets after methane cracking formed methane at various rates in the temperature range of 600 to 800°C. Temperatures of 800°C gave the best methane cracking performance and efficiencies decreased rapidly with temperature.

Jan 1, 2002