Search Documents

By M. Cohen

THERE seems to be a natural urge for the human mind to wonder about the beginning of things. When an explosion occurs, we immediately inquire "what set it off?" If a person contracts a disease, we are likely to ask "how did it happen?" On a much loftier plane, when we reflect about the universe, there is the inevitable question "what, or rather Who, started it all?" In principle, these varied queries have at least one attribute in common: they are attempts, whether earnest or casual, to search out the origin of events in nature. Accordingly, they involve not only scientific, but philosophical and even re1igious matters of deep concern. It is evident that, in a broad sense, the phenomenon of nucleation is enmeshed in this enticing concept of "the beginning", but we must extract the scientific component of the problem for our present purposes. Nucleation, as in the case of phase transformations, is best regarded from the standpoint of kinetics. There are then two main steps, which may come in either order: (a) Experimentally, one attempts to measure the frequency with which transformation centers spring into existence; and (b) theoretically, one seeks a model that will account for this observed birth-rate. Temperature, composition, strain, and prior history are some of the important variables that must be considered both experimentally and theoretically when dealing with nucleation in the solid state. Such interaction of theory and observation is an integral part of science in general, but it is particularly significant in the nucleation problem because the very beginning of a phenomenon invariably occurs on too localized a scale in both space and time to be detected with available techniques. Thus, there is little hope of making direct measurements on the nucleus during its birth or to ascertain the exact nature of the process; one can only infer the details of nucleation from the model whose predicted behavior seems to harmonize best with the measured rate of nucleation and its dependence on known parameters. In the field of solid-state nucleation, both theory and experiment call for much ingenuity, but somehow the conceptual schemes have spawned faster than they can be tested by observation. This is not to say that there are many basically new ideas in modern nucleation theory; rather, as we shall see, it is because the required fine-scale measurements are of immense technical difficulty. Quite likely, some of the nucleation models existent today have survived only because of the latitude permitted by meager data. There is great need to bring theory and experiment into better balance in this important area of physical metallurgy. Although one can

Jan 1, 1959

By L. Bloch

Most mine safety initiatives in South Africa are doomed to limited success because of one simple fact: they are a-historical and un-cultural and do not deal with the serious ?legacy issues? that still negatively impact on safety, production, and relationships. We in the SA mining industry continually use imported, foreign safety concepts and systems that will not work fully in a South African context. ?The 4th Wave: Culture-Based Behavioural Safety?, as developed by Lance Bloch, an international award-winning clinical psychologist with 12 years? experience in the mining industry - focused mostly on Platinum - is making waves. He has been very successful in creating people-centred, empowered, high-performance safety cultures wherever he has worked. Not only does the 4th Wave transform the corporate culture of a mine, improving safety and production and building an environment of Ubuntu, but it also uses people?s cultures as a means of winning hearts and minds in the battle for safe production. Powerful relationships are built through engagement at all levels, leading to all being focused on the best needs of the company and its constituents as a whole. The programmes are no less than nation-building - something most necessary in the industry, with the pressures from community, unions, the DMR, and politicians. This presentation will describe and discuss the 4th Wave as an advance on previous safety technology and programmes, as particularly relevant to platinum mining in South Africa today.

Jan 1, 2012

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By C. D. Woodward

THE Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt. direct current for the haulage systems. Pole lines convey the power from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points .underground. All power is purchased on a maximum-demand basis, therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only eliminates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done, by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. leading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant.

Jan 2, 1922

By R. G. L. McCready, R. O. van Everdingen, M. Kalin, R. van Everdingen

"This paper is based on data generated between October, 1986 and October, 1989, during the implementation of an Ecological Engineering close-out for a zinc mine in Northern Ontario, where 690000 tonnes of tailings contain 41.1% pyrite and 4.1% pyrrhotite. The objective was to determine rates of sulphide oxidation and iron precipitation in the tailings. Those rates are relevant for the assessment of the long-term effectiveness of biological systems employed in the removal of heavy metals from contaminated drainage issuing from tailings.Data were collected on the topography and stratigraphy of the tailings basin, subsurface temperatures and groundwater levels, and chemical analyses were made of water samples collected from a number of piezometers. The thickness of unsaturated tailings varied widely between individual piezometer locations; annual maxima ranged from 0.67 m to 3.55 m, and annual minima from 0 to 2.68 m. Sulphate concentrations ranged from 36 mg/L to 20180 mg/L; iron concentrations from 0.36 mg/L to 9938 mg/L; and zinc concentrations from 0.33 mg/L to 1123 mg/L.The geochemistry of the piezometer samples suggests that some of the initial Fe content, resulting from metal sulphide oxidation, is subsequently precipitated in the tailings pile and, possibly, in the underlying unconsolidated sediments, probably in the form of iron-hydroxide and Na-jarosite. Other metals such as Zn may be co-precipitated with Fe. The discharge of a portion of these metals to the environment would be delayed by this process. Some of the initial sulphate may also be lost from solution, probably by precipitation of gypsum; approximate saturation degrees for gypsum ranged from -3.27 to +0.47. The precipitated minerals will somewhat decrease the porosity and permeability of the tailings.Sulphide-oxidation rates, calculated using the analytical results and the estimated amount of annual recharge at the tailings site, average 0.0057 mol/kg/yr. Calculated iron-precipitation rates average 0.000386 mol/kg/yr. It is concluded that the characteristics of seepage from mining wastes may change with time, reflecting the solubilization of precipitated secondary minerals."

Jan 1, 1992

The Bureau of Mines evaluated short-delay coal mine detonators manu-factured by three domestic companies for electrostatic sensitivity, strength, and no-fire current level. Electrostatic sensitivity was studied in pin-to-pin and pin-to-case modes employing lO-kV potential. Strength of detonation was measured in the Bureau's underwater test fa-cility. No-fire current was measured using a constant-current power supply unit. Test procedures and experimental data are included.

Jan 1, 1985

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

By K. A. Moxham

The ARM 1100 was described in a paper presented at the 6th International Symposium on Mine Mechanization and Automation in September 2001. It started operation underground at Rowland Shaft in early 2002. This paper covers the results of those trials that resulted in more than 1 100square metres of UG2 being mined.

Jan 1, 2004

By B. C. Jena

In a chromite smelting process for the production of high-carbon ferrochromium, the slag composition profoundly affects operating conditions and the economic performance of the process. For a Canadian chromite concentrate, optimum slag composition and operating temperature were determined by process simulation with a computer model, which is based on parameters, such as the minimisation of slag volume, liquidus temperature, electrical energy consumption and chromium losses. Chromium recoveries are identified for slag compositions spanning wide concentration ranges within the quaternary system MgO-AI2O3- SiO2-CaO. The simulated data are compared with the experimental results.

Jan 1, 1994

By C Reed

Titaniferous magnetite deposits are a significant source of vanadium for use in high strength steel alloying and other chemical applications. The mineralogy of the deposits varies markedly and the ore characteristics strongly influence the process route selected and the metallurgical outcomes. Characterisation of the ores reveals the presence of magnetite, ilmenite and other minerals such as spinel hematite and goethite with variable degrees of weathering along with weathered products of host rock. The standard processing route is to crush, grind and magnetically recover a concentrate for salt roasting to produce a soluble vanadate. Ore beneficiation is practised to generate an iron based mineral concentrate containing much of the vanadium with low silica levels of two per cent. Typical processing problems encountered are fine liberation size, over grinding of the magnetite and variable response to magnetic separation resulting from the weathering profile. Beneficiation options are restricted, and generally focused on producing a combined iron and titanium rich concentrate containing vanadium due to the fact that ilmenite and magnetite and their products of weathering are magnetic and have similar specific gravities making their separation difficult. The ilmenite usually contains low levels of vanadium making its separation highly desirable from the iron mineralisation containing higher levels of vanadium. Salt roasting of vanadium ores followed by water leaching has been the standard processing route for many years. The cost of suitable sodium salts, availability of capital and increasing energy costs and energy availability are critical factors in determining the viability of aspiring vanadium producers. To date, only Windimurra has acquired full capital funding, secured energy and sodium salt supplies at suitable cost that enable the construction of the project. Low overall recoveries of vanadium to concentrate roasting at up to 1200¦C are critical cost issues. In this paper, factors influencing the recovery of vanadium are reviewed and emerging processing trends explored. The important features of the processing of titaniferous magnetites have been condensed from the literature, published works, company websites, our own work and personal communication.

Jan 1, 2008

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of gas-solid reactions with special attention given to the hydrogen reduction oj dense spheres of hematite. This reduction process must pvoceed through a sequence of transport and chemical .reaction steps acting in series. Under typical experimental conditions, none oj the individual transport and reaction resistances may be neglected in the development of a physically significant model. A linear vate of thickening oj the product layer, usually taken as evidence of interface-controlled .reuction, may be observed even though transport resistances play a dominant role in the over-all kinetics. The temperature and pressure dependencies of all terms have been carefully evaluated in order to .make fill use oj arailable expe-inzental data in evaluation oj the model. FOR obvious technological reasons, the kinetics of reduction of iron oxides has become the subject of intensive experimental and theoretical investigation during recent years. Continuing efforts to construct mathematical models to describe the kinetics of reaction between a gas stream and a granular bed of solid particles have demonstrated the necessity of a thorough understanding of the reaction kinetics of a single particle within the system as a prerequisite to the construction of physically significant models of complex, reacting systems. This paper presents a critical examination of the transport and chemical-reaction processes involved in single-particle oxide reduction and develops the mathematical expressions necessary to evaluate their importance. Comparison of theoretical predictions with experimental results contributes important new understanding of the complex nature of this process. The reduction process has been studied under a wide range of experimental variables, and it is not surprising that apparent conflicts in observation and interpretation appear in the literature. The interested reader is referred to the reviews of Themelis and auvin"? and Manning and philbrook3 for a description of much of this work. The course of reaction commonly has been followed by measuring the oxygen weight loss from the particle as a function of time. A number of authors have suc- cessfully correlated their data in terms of a model which assumes that the reduction process is controlled by the rate of reaction at a single, sharply defined, advancing interface. According to this model, the interface will advance linearly with time. A mathematical model for gaseous reduction in a packed bed developed by the present authors in an earlier paper4 recognized that reduction must proceed through the series hematite (Fe203), magnetite (Fe30,), wiistite (Fe,O), and finally metallic iron. The reduction scheme permitted a stepwise topochemical reduction of the individual particles to metal or to the lowest oxide thermodynamically possible for the local gas composition in the bed. The limiting situations of theoretically dense and very porous oxide structures were considered. On the basis of available experimental evidence, the simplifying assumption was made in each case that all product layers would thicken linearly with time. A generalized single-particle model has now been developed to determine the significance of transport resistances in the product layers and in the gas film surrounding the particle. The analysis shows that the interplay of transport and chemical resistances is such that an apparently linearly advancing interface may be observed despite the fact that the reaction may be under significant transport control. Attention thus far has been focused on the development of a model for the topochemical behavior of dense spheres of hematite in atmospheres capable of reducing them completely to metal. The formation of successive product layers of iron, Fe,O, and Fe304 is assumed to follow the mechanism originally described by dstrijm.' All oxygen removal from the core occurs at the iron/Fe,O interface, intermediate oxide layers being propagated by sol id-state diffusion without change in the oxygen density of the core. Since fractional reduction is operationally defined in terms of oxygen weight loss, the kinetics of the over-all reduction of FeZ03 to iron is properly studied in terms of the gas-solid reaction occurring at the iron-wiistite interface. The fractional reduction of a partially reduced oxide sphere is given by: here refers to the radial position of the iron/Fe,O interface. This model is not universally applicable because, as explained in the earlier paper,4 a consideration of porous particles or of dense particles in atmospheres not capable of reducing wiistite must allow for the possibility of gaseous reduction at interfaces other than the one between iron and Fe,O. However, evidence that certain hematite specimens actually do follow the dense-pellet mechanism developed here is provided by the data of cewan' and of Bogdandy and

Jan 1, 1967

By Natasa Mitevska

The statistical analysis of the slag composition influence on copper losses to discard slag in the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Yugoslavia) is presented in this paper. The model for the slag basicity calculation is determined, and connected to the copper distribution coefficients between the matte and slag phase. The influence of all components on the slag structure is also illustrated.

Jan 1, 2003

By Antonio Luraschi

The constituents iron, oxygen, silica and cop- per are of principal interest in slags utilized in pyrornetallurgical processes for producing copper. Accordingly, phase relationships in the.Cu-Fe-0-SiO2 system are important when one considers the physico- chemical behavior of slags. These phase relation- ships for the quaternary and constituent ternary systems are developed from available information. Isothermal composition and composition-oxygen potential diagrams, and oxygen potential-temperature diagrams are utilized to describe the' important relationships.

Jan 1, 1976

By Edgar A. Scholz

The purpose of this paper is to make a comparative cost analysis of domestic and foreign exploration projects which developed into mines during the 1960-1974 time period. A total of 18 mining companies, American and Canadian, were approached to solicit cost data on domestic and foreign exploration projects which developed into mines. Only 20 percent of the companies to which questionnaires were sent made data available. Several companies answered negatively, informing us that they would have difficulty in attempting to sort our costs. Some companies were usable to release cost details. It is comforting, however, to realize that some of the non-contributing companies expressed eagerness to hear the findings of this paper. Inasmuch as the data available on exploration expenditures is, in some cases, somewhat uncertain and that no two mining companies follow the same system of cost allocations, the results obtained in this analysis should he interpreted as trends of a general character.

Jan 1, 1976

By M. Potesser

In the past, different furnace types have been developed for use within the copper industry, with two common anode furnace designs typically used in copper smelting plants worldwide: the tiltable reverberatory furnace (KPO) generally used for the secondary copper industry and the cylindrical or drum type anode furnace (TRO) for handling a liquid blister charge generated in primary copper production. The disadvantage of the KPO is its design related to the longer refining period, because of the low bath depth, however it provides good conditions in the melting period due to its large bath surface. On the other hand, small amounts of scrap charged into the TRO increase the melting and dissolution period, but it provides good conditions for the refining period. The newly-developed elliptical furnace concept (TRE) offers the advantages of each of these furnace types. The special design allows melting of the scrap more efficiently than in the KPO and refining the liquid copper more efficiently than the TRO. This paper shows a metallurgical comparison of the three furnace types in regard to the melting period by heat technological considerations (optimized arch design) and of the refining period done by CFD with concentration on current, recirculation and dwell time of the gas in the melt. The paper outlines the possibilities for a reduction of the tap-to-tap time and energy consumption as well as for an increase of the production capacity, which can be achieved by applying the TRE instead of the conventional furnace designs.

Jan 1, 2007

By K Timtner

As shown in former publications there are problems in load sharing of backstops in multiple drives of conveyors. Therefore, detailed calculation methods and design recommendations are required. In this paper various designs of load sharing methods are described and a dynamic torque calculation method will be presented. With this method the loadsharing properties for low and high speed backstops are calculated and compared. These properties depend on the spring characteristic of the drive train between backstop and load. Furthermore, the properties depend on the method of torquearm support and shock absorber configuration. Remarkable differences for external and internal backstops are shown

Jan 1, 1998

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

By C. Trepka-Bloch

Silver-copper-zinc mineralization is confined to metasomatically altered late Paleozoic and Cretaceous sediments consisting predominantly of limestone, siltstone and sandstone units. Mineralized alteration halos are spatially and presumably also genetically related to the emplacement of a Cretaceous quartz monzonite stock. Several generations of ore formation and alteration took place. Distribution of skarn and ore was influenced by intrusive contacts, calcareous horizons and by relatively less permeable rock units which served as barriers. Most of the ore bodies form conformable near horizontal mantos but some follow steeply dipping monzonite dikes. Structurally controlled alteration pipes connect the mantos locally. The deposit is strongly affected by mineralized fault and breccia zones.

Jan 1, 1986

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006