Search Documents

By R. R. Klimpel

Introduction The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and in the development of coal gasification/liquefaction processes that require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high-density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology (Klimpel, 1982,1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variation in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: 1) slowing down of breakage rates, 2) the occasional acceleration of breakage of some sizes, and 3) conditions where chemical additives will increase rates of breakage. In brief, these conditions were analyzed using two different criteria: a) the net production rate of material less than some specified size (e.g. kg/min of minus 325 mesh) in a standard batch laboratory mill test as a function of controlled changes in grinding conditions, and b) the use of the one-size-fraction feed method, which consists of following the disappearance of this largest size over grinding time in a batch laboratory mill to arrive at well-known specific rates of breakage (Austin et al., 1984). Detailed references to the methodology used as well as the conclusions are available (Klimpel, 1982, 1982/83) and will not be repeated here. The purpose of this paper is to further demonstrate several additional characteristics of dense coal-water slurry grinding that were shown in a simplified sense in the earlier publications of the author but which have clearly demonstrated themselves as being very important in the industrial simulation and scale-up of such coal-water grinding systems. In particular, this includes the clear and unambiguous demonstration of how the simultaneous acceleration of breakage of some size fractions and slowing down of the breakage of other size fractions is occurring as a function of changes in coal-water slurry density. In the earlier publications (e.g. Klimpel, 1982), it was shown by specially designed experiments that the addition of fine material and/or the use of a chemical thickening agent accelerated the specific rates of breakage of coals of coarser size fractions using the one-size-fraction method. There were also numerous examples given of non first-order breakage (the slowing down of coal breakage rates) using also the one-size-fraction method due to the presence of excessive amounts of fines which corresponded to the development of a rheological yield value. The problem with the simulation and scale-up of any laboratory and/or pilot-scale mill data to an industrial scale using the mechanistic modelling approach involving specific rates of breakage and breakage distribution parameters (e.g. Austin et al., 1984) is the number of assumptions involved in translating the smaller mill breakage parameters to the predicted larger mill breakage parameters. It is apparent, at least to this author, that to accurately simulate and predict larger scale equipment performance from smaller scale data (given that the larger scale data performance is known and hence predictions can be thoroughly checked) requires a better knowledge of breakage parameters than is currently available. More specifically, it was felt that one of the chief problems was the inability of the one-size-fraction method of determining breakage parameters to sufficiently represent the actual magnitude and sometimes even the directions of. the complicated interactions involved with slurry density changes in coal-water slurry grinding. Thus, a special set of experiments was conducted in a somewhat larger batch ball mill (0.457 m diam x 0.610 m length) than the 0.203-m-diam mill used in the original rheology characterization paper (Klimpel, 1982) so as to minimize any unusual effects due to wall-ball interactions (2.54-cm-diam balls used in both mills). More importantly, the measurements of specific rates of breakage were done using a proprietary tracer method on a portion of a given size fraction, which was then remixed into a natural feed size distribution before grinding. The experimental procedure and analysis of subsequent data was done in exactly the same manner as the radioactive tracer technique on coals as originally developed by Gardner (1962). The advantage of such an approach is that it makes no assumptions such as the independence of the specific rate of breakage of any size on the absolute sizes and amounts of other sizes present (both larger and smaller) in the mix of natural feed material. It will be shown that the measured rates of breakage using the direct tracer technique and the one-size fraction method on the same coal are indeed different. In fact, an accurate assessment of what is happening to the rates of breakage as a function of changing slurry density can only he made by measuring particle breakage under grinding conditions approximating the size distributions actually being produced in practice. Experiment procedures and results The pilot mill used was 44 cm diam x 60 cm long with a volume of 91,250 cm3 and was fitted with six 0.5-in. lifter bars.

Jan 1, 1992

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

HIGH-GRADE manganese ore, from which manganese is obtained commercially, is not found in large quantities in any major steel-producing nation in the free world. The U. S. is a "have not" nation with respect to deposits of directly mineable high-grade manganese ore. Known resources of 48 pct Mn or better grade ore amount to less than 200,000 tons. In 1950 the U. S. steel industry consumed 1.8 million short tons of metallurgical grade manganese ore that contained about 800,000 tons of manganese. About 16 pct of the manganese content was lost in processing, so that about 650,000 tons, or 13 pounds per ton of steel actually entered into steel production. Under present practices use expands directly with steel output, and by 1975 the demand in both the U. S. and the rest of the free world is expected to be roughly 60 pet greater than in 1950. In peacetime about 80 pet of manganese consumption goes into steel production; high-manganese steel, dry cells, and chemicals account for the remainder. The manganese supply problem centers around high-grade ore for ferromanganese production. Use of ores containing less than 35 pet Mn sharply increase the costs of making ferromanganese. Use of ferro-manganese of grade below 70 pet in turn requires changes in steelmaking that increase steel cost. Under normal conditions the present small domestic production cannot be expected to increase. Major resources in the U. S. consist of 12 low-grade deposits. The cost of mining and treating these ores to extract a product as good as that yielded by imported ores is at least twice and in some cases more than four times the 1951 price of foreign ores delivered to the U. S. However, as long as trade relations and overseas shipping are not interrupted, deposits in India, Africa, and Brazil can meet steadily increasing demand at approximately present costs. Cost considerations indicate that the U. S. should continue to rely upon overseas sources for its peace-time supply, and that this situation is satisfactory. But, this does not take into account the question of how the U. S. will be able to meet its needs in war. Position of the Rest of the Free World In 1950, free world steel producers outside the United States, with a steel output of 70 million ingot tons, consumed about 1.3 million tons of metallurgical-grade ore. Their manganese ore demand, expected to increase directly with steel production, will by 1975 be about 2.3 million tons. Russia possesses over half the known manganese ore reserves of the world and is producing twice the tonnage of any other country. It supplied more than a third of the U. S. manganese requirements up to 1938 and again in 1948, but by 1950 Soviet manganese exports to the free world had virtually ceased. The free world's supply of manganese now comes mainly from India and Africa. Somewhat over 10 pet of U. S. imports came from Brazil and Cuba. Security Considerations In the event of war the U. S. might be substantially cut off from 90 pet of present sources. Reduction in manganese specifications might cut consumption by over 10 pet without seriously affecting steel quality. By elimination of losses in the production of ferromanganese savings as high as 10 pet might be possible. But, wartime manganese requirements cannot be met through conservation alone. To meet possible future emergencies the U. S. should continue its comprehensive security program for manganese, including stockpiling and research on the economic use of low-grade ore, domestic ores, the recovery of manganese from slag and the reduction of manganese requirements in steel production. If this work, including additional pilot plant operation is pursued vigorously, it should be possible in an emergency to get an adequate supply of manganese from domestic sources. The national stockpile then can be looked upon as a source of supply during the period of at least 2 years required to reach full-scale production from low-grade resources. Ferromanganese Smelting In comparison with smelting of pig iron, ferro-manganese smelting is a very wasteful process. Under present ferromanganese blast-furnace smelting practice, about 8 pet of the manganese in the furnace charge is lost to the slag, and roughly the same amount is lost to the stack gases; the total loss approaches 15 pct. Present practice is a compromise between excessive slag loss and excessive stack loss. In fact, it may be seriously questioned whether conventional blast furnace design is suitable for manganese smelting. U. S. Resources The known manganese deposits of the U. S. contain a total of 3500 million long tons of raw material and 75 million long tons of metallic manganese. More than 98 pct of this contained metal is in 12 large low-grade deposits of which the most important are those at Chamberlain, S. Dak; Cuyuna, Minn.; Aroostook County, Maine; and Artillery Peak, Ariz. Reserves of high-grade ore (48 pct Mn) amount to less than 200,000 tons. About 20 million tons of ore average over 15 pct Mn, and when grade is decreased to 10 pct Mn reserves amount to about 100 million long tons. If cut-off grade is decreased to 5 pet Mn, resources amount to 800 million long tons. Many of these low-grade ores may be beneficiated by flotation or other concentration methods. Pyrometallurgical Methods For smelting ferromanganese, it is essential to have an ore containing at least 50 pct manganese, with an Mn:Fe ratio of about 8:1. Direct smelting of 20 pct Mn concentrates is not promising. The only method that offers any promise involves two-step smelting.

Jan 1, 1952

By Robert J. Hite, James P. Searls, Sherilyn C. Williams-Stroud

Potash is a generic term that includes potassium chloride, potassium magnesium sulfate, potassium sulfate, potassium nitrate, and sodium-potassium nitrate mixtures. In the ceramics industry, potash is also used to refer to potassium oxide. Potash, primarily in the form of potassium carbonate, was the first industrial mineral produced in the United States, and the first US patent issued was for an apparatus and process developed in 1790 for its production (Paynter, 1990). Prior to the 1860s, potash was primarily sold as an impure form of potassium carbonate produced by burning hard- wood trees and leaching the potassium salts from the ashes. The major early uses of potash include soap and glass making, dyeing fabrics, baking, and saltpeter for gunpowder. In 1859, the development of a purification process to remove the sodium and magnesium chlorides was developed for the carnallite found at Stassfurt, Germany, and mined potash became available. With the appearance of mined potash and the earlier (1840) discovery in Germany by Justus von Liebig that potash was a nutrient for crops, potash started to be used for high valued crops such as cotton and vegetables. The German potash companies quickly developed a manufacturing process for producing potassium sulfate for tobacco fertilization. German potash supplied nearly all American needs until the embargo of the First World War when imports from Germany were interrupted (Bateman, 1918). With the discovery of potash deposits in New Mexico in 1931, the United States became self-sufficient in potash. In 1962, the United States began importing potash from Canada, and two years later domestic apparent consumption began to exceed domestic production. Along with nitrogen and phosphorus, potassium is one of the three essential plant nutrients, the "K" of NPK terminology. As a result, 95% of potash production is used as plant fertilizer. In all plants, inadequate potassium diminishes growth, causes increased disease, stalk and stem breakage, and susceptibility to other stress conditions. Plants take up large quantities of potassium from the soil, and potash fertilization replaces this loss so that each new crop can be grown with the same vigor and productivity as the previous year's crop. The potassium depletion of the soil from growing repeated cotton and tobacco crops is well known in the history of southern agriculture in America. George Washington was known to have studied alternative crops that could be grown on soil that had been depleted by repeated tobacco crops. Most of the remaining 5% of potash consumption is by the chemical industry, as potassium hydroxide to produce soaps and detergents, glass and ceramic products, dyes, explosives, alkaline batteries, and medicines. Potash as chemical is used in oil field drilling mud, the aluminum recycling industry, and the electroplating industry. Additional minor uses for potassium chloride include water softener regeneration, sidewalk deicing, and salt substitution for human consumption. Potash is used in the food industry as potassium phosphate, and in production of glass products as potassium carbonate or nitrate. GEOLOGY Potassium is the seventh most abundant element in the earth's crust and the sixth most abundant element in seawater. It is found in silicate minerals of igneous, metamorphic, and sedimentary rocks and is also a major constituent of many surface and subsurface brines. The majority of world potash resources are found in subsurface bedded salt deposits which yield high grade, large tonnage ore bodies and are amenable to low cost mining and beneficiation. Because of the relatively high solubility of potassium minerals, potash from salt deposits is ideal for use as fertilizers. Some potash production is from evaporation of naturally occurring brines, but the vast majority of current domestic and international production is from bedded salt deposits. Sylvite, carnallite, kainite, and langbeinite are some of the more important potassium minerals (Table 1). Sylvinite, a mixture of KC1 and NaCl is the highest grade potash ore. Carnallite can be considered a potash ore when removal of magnesium chloride is included in the beneficiation, but it can also be considered a contaminant when mining for sylvite. Potassium sulfate and potassium nitrate are typically manufactured products. Potassium sulfate is produced from mined minerals through conversion processes in Italy, Germany, and Carlsbad, NM, and from brines in southern California and at the Great Salt Lake in Utah. Natural deposits of potassium nitrate occur only in small amounts in Chile. The majority of potash-bearing bedded salt deposits are believed to have originated from the evaporation of seawater or mixtures of seawater and other brines in restricted marine basins (Schmalz, 1969). The reflux depositional model for evaporite deposition was first described in the literature in 1888 by Ochsenius. A shallow bar, or sill, across the mouth of a basin lets in a restricted flow of seawater which evaporates into a salt-precipitating brine (Fig. 1). The density of the brine at the distal end increases with increased salinity, sinks to the bottom, and sets up a reflux current of higher density brine back toward the ocean. The sill, which restricts the inflow of seawater, allows inhibited flow of evaporation-concentrated brines back to the ocean. The least soluble salts are precipitated nearer the sill, and the most soluble components come out of solution in the deeper parts of the basin. The result is a lateral facies change in a tabular-shaped deposit that is due to the salinity gradients in the brine (Fig. 2A). The asymmetrical facies distribution of the Paradox Formation (Middle Pennsylvanian) Utah (Hite, 1970), the Prairie Formation (Middle Devonian) in Saskatchewan (Holter, 1972), and the Salado Formation (Upper Permian) in New Mexico (Lowenstein, 1988), might prompt explanation by such a model. Other deposits, such as the Salina Formation (Upper Silurian) in Michigan (Matthews and Egleson, 1974), show a facies distribution that could be described as a bull's eye pattern. Although some small subbasins of high grade sylvite are found near the margins, the potash is generally located in a central part of the basin surrounded by successively less soluble facies (Fig. 2B). The sparse

Jan 1, 1994

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By Douglas Ashmead

In his paper Mr. Braley makes no mention of the bacteriological aspects of the problem. It is now quite well established that certain bacteria play a major role in formation of acid mine waters, and it is a simple matter in the laboratory to show that under sterile conditions the rate of acid production from a pyrites suspension is only about one quarter of that obtained from a similar suspension inoculated with drainage from a mine producing an acidic pit water. Under sterile conditions the oxidation is due to direct chemical action and, from the evidence just given and from much other evidence, this increase under nonsterile conditions is due to certain bacteria. Experiments recently completed, and shortly to be published, have shown that this bacteriological oxidation can be prevented by the maintenance of pH conditions above 4. It was found that to raise this pH above 4 at the beginning of the experiments was not sufficient but that, due to the continuing chemical oxidation, alkali had to be added daily to maintain the pH conditions above 4. The amount of alkali added, however, over a fixed period, was only about one quarter of the alkaline equivalent of the acid produced when pH conditions were not controlled over an equal period. The opinion expressed by Mr. Braley that sodium hydroxide has little or no effect on the rate of oxidation of pyrites is not substantiated by the above experiments. The writer does not claim that these results show a practical solution to the problems, especially in abandoned workings, but feels that the application of an alkaline coating, such as lime wash, to exposed accessible workings might be well worth trying. S. A. Braley (author's reply)—In 1919 Powell and Parrl suggested that bacteria, or some catalytic agent, hastened the oxidation of pyritic or marcastic sulfur in coal. Carpenter and Herndon (1933)' attributed the action of Thiobacillus thiooxidans. Colmer and Hinkle (1947)3 observed an organism similar to T. thiooxidans and another organism that oxidized iron. Leathen and Braley 9rst discovered this organism in 1947 in a sample of water from the overflow of the Bradenville mine (Westmoreland County, Pennsylvania). They characterized the organism in 1954" and gave it the name Ferrobacillus ferrooxidans. Although Temple and Colmer (1951)' had suggested the name Thiobacillus ferrooxidans, since they claimed it oxidized both ferrous iron and thiosulfate, we have found that pure cultures of the organism do not oxidize thiosulfate, hence the name F. ferrooxidans. In 1955 Ashmead7 isolated an organism, similar to the one called Thiobacillus ferrooxidans by Temple and Hinkle, from acid mine water in Scotland. It is probable that this organism was F. ferrooxidans. In 1954 Bryner, Beck, Davis, and Wilsonh reported microorganisms in effluents from copper mine refuse. These organisms appeared to be similar but were not in pure culture. In view of this history of bacterial investigation of acid mine water and our own ten years of experience, we do not agree with Mr. Ashmead that bacteria play a major role in acid formation. We do not find that any of these bacteria will directly oxidize pyritic material. They do, however, augment the chemical formation of sulfuric acid by atmospheric oxidation. In two papers in 1953% eathen, Braley, and McIntyre discuss the role of bacteria in acid formation and postulate the mechanism through which they operate. Mr. Ashmead in his discussion of my paper has assumed that this work was carried on in the presence of acid mine water in which bacteria would be present. This was not the case. Strictly sterile conditions were not maintained, but the organisms present in mine drainages were definitely absent in these experiments. We believe that we have demonstrated that alkalis do not inhibit the chemical oxidation of pyritic material. This is also indicated by Mr. Ashmead's discussion in which he says that alkali must be added daily due to the continuing chemical oxidation. It is interesting to note that Mr. Ashmead finds that maintenance of pH above 4.00 decreases the activity of the bacteria. We have found also that a decrease in pH below 2.8 also inhibits its activity. Table XIII of published data'" illustrates the decrease in activity with increased acidity, although pH values are not given. These values are in comparison with uninoculated controls and show the marked increase in acidity up to 22 weeks but a decline at 29 weeks, at which time the experiment was terminated. It is probable that after a longer period only chemical oxidation would have continued. From our studiesv we have postulated that the iron oxidizing bacterium (Ferrobacillus ferrooxidans) oxidizes the ferrous iron, resulting from chemical oxidation, to ferric iron. The ferric iron then aids the atmospheric oxidation of the sulfuritic material and is itself reduced to ferrous iron, which in turn acts as food for the autotrophic bacteria. Study of the physiologic properties of F. ferrooxidans shows that its preferred pH is about 3.00 and its activity decreases with variation in either direction. It is extremely inactive above pH 4.00 and below 2.5. This inactivity above 4.00 is indicated by Mr. Ashmead's observations. These properties of F. ferrooxidans then correlate perfectly with our hypothesis. Ferrous iron is oxidized very slowly by atmospheric oxygen in highly acid sohtion and since the bacteria become inactive, acid is formed only by atmospheric oxidation. At a pH of 4.00 or above iron is more readily oxidized by atmospheric oxygen, but the bacterial activity is decreased. However, with a pH above 4.00 the ferric iron is removed from the field of activity since its soluble sulfate hy-drolyzes and precipitates the iron as ferric hydroxide or a basic sulfate. As we have shown in the paper under discussion, the alkali does not inhibit the chemical oxidation, and thus the acid formation continues. This

Jan 1, 1957

By Milton R. Pickus, Earl R. Parker

THE modern theories of creep¹-4 in general have been based upon the concept of generation and migration of dislocations, with the generation process normally assumed to be rate controlling. The theories are generally deficient in that they fail to take into account many factors that are known to influence creep. The influence of the state of the surface of the test specimen has been almost completely overlooked; yet the present report shows that the nature of the surface may, in certain cases, govern the creep characteristics of a specimen. In the period since Taylor" applied the concept of dislocations to a study of metals, a school of thought has developed that closely relates the plastic deformation of metals to the generation and migration of dislocations through the crystal lattice. It might be expected that the thermal energy required for the generation of a dislocation would be different from that for migration of the dislocation through the lattice. Furthermore, the activation energy for generation would be expected to vary for different parts of the solid metal. It has been predicted that dislocations would be generated most easily at external surfaces, but could also be activated at certain internal surfaces such as grain or phase boundaries. Within the body of the metal a range of values for the activation energy might be expected because of different degrees of disorder at such regions as grain boundaries, impurities, and second-phase particles. The particular value of the activation energy that was rate determining could then depend on the specific conditions of a test. If, for example, the surface atoms were by some means constrained, the generation of dislocations in the body of the metal might become the important factor. On the other hand, other conditions may favor generation at the surface. It is possible then that the creep behavior may not be completely determined by the inherent properties of the metal. Even the environment in which a test is carried out could have a significant effect. In fact it is conceivable that in order to obtain the maximum creep resistance from a given alloy, the surface atoms must be so constrained that the activation energy for generating dislocations on the surface is at least equal to that required for generation in the body of the metal. On the basis of such considerations, and in view of the limited number of publications discussing this subject, it seemed that an investigation of the influence of the state of the surface on creep might yield information of both theoretical and engineering interest. Experiments on single crystals, demonstrating a variation in the mechanical properties due to alterations in the surface layer, have been reported by several investigators.6-13 he results of these experiments have been briefly summarized;14 consequently, the earlier work will not be reviewed here. As an example of these findings the observations of Cottrell and Gibbons may be cited. They reported the critical shear stress of a lightly oxidized cadmium single crystal is greater by a factor of 2½ than a specimen with a clean surface. Materials and Methods Single crystals M in. in diam and 8 in. long were prepared from Horse Head Special zinc, melted under an atmosphere of helium in a large pyrex test tube, and drawn up into a long ½ in. diam pyrex tube by means of a vacuum pump. The cast zinc rods thus produced were cut into convenient lengths and sealed in evacuated pyrex tubes. Single crystals were grown by gradual solidification of the remelted rods. Cleaving the ends of the single crystal specimens chilled by liquid nitrogen proved a simple method for determining orientations from the exposed basal plane from the markings left on the cleaved surface that gave the slip directions with sufficient accuracy for the experimental work. The specimens chosen for the experiments were those having the angle between the basal plane and the specimen axis within the range of 15" to 65". Since zinc single crystals are quite delicate, it was necessary to devise an appropriate method of gripping the specimens in order to suspend them in the furnace and apply the load. Stainless steel collars were prepared having an inside taper, the smaller end of the taper being of such a size that the specimen could just pass through freely. The tapered hole did not extend the full length of the collar; a sufficient thickness of metal remained so that a hook could be attached to provide a means of applying the load and suspending the specimen. One of the collars was slipped over the upper end of a specimen which was supported vertically in a steel jig. The collar was then heated electrically until the end of the crystal melted and filled the collar with molten zinc. At this point the application of heat was discontinued, whereupon the molten zinc quickly solidified, due to the chilling effect of the jig. The specimen was then inverted and the second collar applied in a similar manner. The jig served several purposes: limiting the length of specimen that was melted, providing excellent alignment of the collars with respect to the specimen axis, and protecting the specimen from mechanical damage. Once the specimen was suspended in the furnace and loaded, it was desired to accomplish the surface treatment with a minimum of disturbance of the specimen. Around the specimen was a long pyrex tube, the upper portion of which was approximately 1 in. in diam, and in it was a copper coil of such a diameter to fit snugly against the tube. A specimen, approximately ½ in. in diam and 4 in. long, was suspended by means of a stainless steel rod so that it hung within the copper coil. The lower portion of the glass tube was approximately ¼ in. in diarn, and passing through it was a 5/32 in. diam stainless steel rod which hung from the lower specimen collar. This portion of the glass tube and the stainless steel rod extended through the bottom of the furnace. A T-connector, with suitable packing, was attached to the lower end of the stainless rod to provide a water-

Jan 1, 1952

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By V. C. Allen

THE Tri-State Zinc, Inc., Galena, Ill., was confronted with the problem of securing ore from a deposit because the hoisting shaft was several thousand feet from the mill. The orebody is several thousand feet long, averaging 200 ft in width and 60 ft in height and opened up by vertical shafts some 300 ft deep. Mining is by the room-and-pillar method. During the initial operation the ore was loaded by conventional electric 1/2-yd boom-and-dipper shovels and hauled to the shaft by 8-ton diesel trucks. This underground ore loading and hauling was well adapted to the conditions and productive of low costs per ton. However, with the mill situated as mentioned, a triple handling of all broken rock was necessary: l—from the stope to the shaft by truck, 2—up the shaft by skip br can into the surface hopper, and 3—by truck from the surface hopper to the crushing plant at the mill. In addition to the repeated handling, serious troubles were encountered during the winter because of freezing in the shaft hopper. Consideration was given to either moving the mill to the new orebody or to the construction of a second mill. The presence of other orebodies to be mined at a later date made the first alternative impractical while the capital outlay for a second mill, when the present plant of approximately 850 tons per day was deemed sufficiently large for the total reserves, made the second alternative also unwise. It was decided to retain the mill in the originals location and continue to move the ore to it. The idea of driving an inclined adit from the surface to the bottom of the orebody suitable for truck haulage and big enough to allow the passage of all mechanical equipment was conceived. Among the apparent advantages of such an incline were: 1— Direct haulage from the stope to the mill without rehandling. 2—Elimination of virtually all grizzlies. Trucking from underground to the mill would do away with all hoppers, chutes, gates, and skips and make the maximum rock size dependent solely on the size of the shovel dipper at the mine and the crusher opening at the mill. 3—Less secondary blasting would be needed. 4—Ease of transporting equipment and supplies underground. Shovels and trucks could be taken through the incline intact. 5—Equipment could be brought to the surface for repairs and servicing without loss of time. The same advantages of ease in moving would be present in the handling of men, steel, powder, and supplies. 6—There would be far less difficulty in increasing the amount of tonnage that could be moved by truck up an incline than would be found in attempting to increase the capacity of a shaft. 7—All the broken ore in the stopes would serve as bin capacity, as it would take the breakdown of all of the loading and hauling equipment to have the same effect as a delay in shaft hoisting. 8—All danger of men being trapped in the mine as a result of shaft fire or power stoppage would be eliminated. 9— Virtually all trouble from severe winter conditions would be eliminated by the direct haul underground to the mill. The decision was made to proceed with the driving of an inclined adit. The topography of the surface between the orebody and the mill was such that it was possible to locate the portal at a point 170 ft above the mine floor and 1800 ft horizontally from the central point of the orebody to the south and 2500 ft from the mill to the north. A grade of 10 pct was found to be optimum for continuous truck haulage when the various factors of speed, safety, and truck maintenance were all considered. The incline as driven was consequently 1700 ft long on 10 pct grade and 12 ft high by 17 ft wide in cross section. The tunnel-driving equipment was chosen so that it could be used in mining after the completion of the tunnel. Drilling was done with a jumbo with two Joy jibs mounting 3-in. drills, loading with an Allis-Chalmers diesel-powered, front-end loader of approximately 11/4-yd capacity, and hauling by Koehring Dumptor trucks of 8-ton capacity, diesel-powered. The width of the tunnel allowed the end loader and Dumptor to be placed abreast. Since the Dumptors can be driven either forward or backward with equal facility, loading was accomplished without turning around either machine throughout the loading operation. The crew in addition to the tunnel foreman was comprised of three men per shift at the start and in the later work, four men. Each crew could perform any part of the working cycle. If the drilling was completed and the round blasted in the middle of a shift, the same men would proceed with the loading and hauling. Since the mine already had been drained to the bottom levels, no water was encountered. At the halfway point the tunnel was widened for approximately 100 ft to permit trucks to pass. The total cost of the tunnel excluding the capital outlay for equipment, which was all continued in use in the subsequent mine operation, was $60,363.00 or $35.50 per ft. The tunnel was completed at the end of June, 1949 and has been in continuous use since that time. In the five months from July to November inclusive, 106,049 tons have been transported to the mill or an average of 835 tons per day. No unforeseen disadvantages have been encountered and the advantages which had been predicated before the adit's construction have been more than realized. As previously mentioned, the deposit is worked by the room-and-pillar system with occasional faces up to 125 ft high. Except in driving development drifts when diesel-powered, front-end loaders such as were used in the tunnel are employed, all shoveling is done by Yz-yd boom-dipper type shovels electrically driven. These units need a width of 25 ft and a height of 14 ft in which to operate. All hauling is by diesel trucks, mainly Koehring Dump-tors. Roads are maintained with caterpillar tractors and a road grader. The tonnage output from the

Jan 1, 1952

National Minerals Advisory Council A meeting of the National Minerals Advisory Council on August 3rd in Washington, D. C., indicated the vitally important part that the mining industry is to play in the mobilization program. Director James Boyd of the Bureau of Mines told the Council that the Department of the Interior would review the recommendations of all the Council's commodity committees with regard for mobilization planning in the light of the changed international picture. The Council was requested to reactivate its commodity committees and have them gather all available data on supplies, their sources and availability and present and potential production of the minerals and metals represented on each committee. Data on labor, machinery, transportation, automotive and stationary equipment, power, fuel, lumber, water supply are a few of the important items called for in the reports, which are to be presented at a meeting of the Council on September 1 at Salt Lake City. The material in the reports will become the basis for discussing metal and mineral requirements at that time. Discussion at the meeting bared several $64 questions, probably the most important of which are the following: 1. Which of the war-essential metals and minerals and in what quantities can we reasonably expect to get them from abroad under threat of submarines? 2. How are we going to meet the manpower problem posed by (a) migration of labor from mining to manufacturing since the end of World War II and (b) the draft and the calling up of reservists? Opinion was expressed by industry spokesman at the meeting that the function of complying with mobilization requirements be left to those in the industry itself; that is, those having the "know how." This view contended that any administrating governmental agency should be kept as small and streamlined as possible. There was general sentiment against the reactivation of the wartime Premium Price Plan or other bonus plans as a stimulus to production. The thought was emphasized that what was needed was a change in the basic conditions which have fostered the decline in domestic mining activity in the postwar years. One such condition, long overdue for correction, is the tax structure as it applies to mining enterprises. Many quarters both in industry and in government favor tax relief along the lines suggested in the six tax recommendations by the Council to the Secretary of the Interior last December. The Council adopted a resolution expressing a feeling that the following tax recommendations are still feasible and desirable and will accomplish as much toward increasing exploration for new deposits (thereby subsequently increasing production) as will government loans for exploration: (1) Losses from unprofitable ventures should be allowed corporations, partnerships, or individuals as ordinary deduction against current income. (2) Development costs after discovery should be recognized as operating expenses. (3) Allowance for depletion should be made to the stockholder as well as to the corporation. (4) Income should not be taxed without full allowance for losses of loss years. (5) Adequate allowances for percentage depletion should be made. A discussion of the manpower problem led to the Council's acceptance of a resolution advising that "military authorities should proceed with caution in depriving the mining and metallurgical industry of its manpower." The resolution strongly urged that no personnel "directly engaged in exploration, development, production or supervision (of strategic and critical materials) should be drafted for the armed forces, at least until the anticipated demands upon these producers are clarified." Stockpiles The Munitions Board's "Stockpile Report to the Congress" of July 23, 1950 revealed: (1) The total estimated value of the stockpile objective is $4,051,714,510 at the close of fiscal year 1950. (2) The total value of the stockpile on hand, at the close of fiscal 1950 was $1,556,154,352 or 38.4 pct of the total stockpile objective. An additional $494,948,060 was on order, making a total of 50.6 pct on hand plus the amount on order. (3) Materials obtained for the stockpile by the ECA from January to June 1950 amounted to $13,112,085, while development projects by ECA during this period involved the expenditure of $9,322,000, mainly with counterpart funds. Shortly after the start of the Korean conflict it was felt that Congress ould appropriate greatly increased sums for the purchase of materials for the stockpile. This stimulus to the program may increase the dollar earnings of those European nations that are present or potential contractors in our stockpiling program. Such a development would mean that these nations could add to their gold reserves, thereby stabilizing their respective economies and hastening recovery. This seems to be the picture for the next six months anyway. The "bug" appears when it is realized that the increased threat of total world war actually may retard recovery in Europe as nations on the continent may feel inclined to devote more of their resources to defense programs. Industries Essential to Defense The Department of Commerce in response to a request by the Department of Defense issued on August 3, 1950 a "Tentative List of Essential Activities" as a "guide for calling up for active duty members of the civilian components of the Armed Forces." The list includes the following: Primary Metal Industries. Included herein are establishments engaged in the smelting and refining of ferrous and nonferrous metals from ore, pig, or scrap. Metal Mining. This category includes establishments primarily engaged in mining, developing mines or exploring for metallic minerals (ores). This group includes all ore dressing and beneficiating operations. Anthracite Mining, Bituminous Coal and Lignite Mining, Crude Petroleum and Natural Gas Extraction, Mining and Quarrying of Nonmetallic Minerals, Except Fuels. Challenge to the Mining Industry The source of our country's great strength lies in its capacity to produce. In times of stress such things as national morale and manpower are all-important but without a capable industrial machine we would be helpless. That machine must be fed with minerals and metals in order to generate and maintain momentum sufficient to insure success. Consequences of the lack of adequate supplies of essential metals and minerals to increase and sustain our industrial power are not pleasant to contemplate. It is absolutely imperative that we put forth Herculean effort to guarantee ample supplies of such essential materials as copper, lead, zinc, manganese, antimony, mercury, tungsten, tin, chromite, nickel, cobalt, iron ore and rubber. The mining industry faces a challenge more serious than ever existed before in the history of our country. The industry must be equal to the task.

Jan 9, 1950

By R. D. Currie

The practicability and dependability of two permissible methane-indicat- in detectors recently developed were proved conclusively by extensive tests in the return airways of all mines operating in the anthracite region in most of which samples and readings were taken with one or the other of the two in- dicating detectors. These detectors roved dependable and accurate within practical limits, and their general use should be encouraged as an aid to bet ter ventilation, more accurate control of air currents, and greater safety in mines.

Feb 1, 1936

By D. Harrington

In general, mining is carried on underground, that is, in confined places where it is difficult to obtain adequate lighting and frequently in rock strata requiring much care to prevent caving. Moreover, explosives must be used in mining with the numerous hazards associated with them, and some mines give off explosive or irrespirable gases; also, ma- chinery must be used, usually under conditions much more hazardous than on the surface. These and many other considerations cause mining to be probably the most hazardous occupation in which large numbers of our fellow countrymen are employed. Prevention of accidents in the mining industry is far more complicated than in surface industrial work, even of the more hazardous types, because the different elements that enter into possible accident occurrence are ascertained more readily above ground and suitable action can be taken against them; moreover, errors in connection with prevention of accidents in surface industrial work usually affect only one or, possibly, a few persons, while in zines one human error may readily cause an explosion or other untoward occurrence resulting in the death of scores or even hundreds of persons. This difficulty in the prevention of accidents in and around mines is well-known, and most countries and States have regulations to guard the safety and, to a much smaller extent, the health of workers in mining and allied industries. In general, the State laws and regu- lations regarding the welfare of mine workers are merely a skeletonized outline of some more or less fundamental minimum requirements and are far too general to do much more than suggest some procedure which may or may not be safe or healthful. Most of them are grotesquely out-of-date as applied to present-day conditions, and none of them is adequate to protect life, limb, health, or property. Unquestionably, there is great need for a closer correlation of the laws and regulations of the various States with regard to safety in the mining and allied industries, and while mining conditions vary far too much for a standardized mine safety law applicable to all of the States, on the other hand there are numerous standard and fairly fundamental safety pro- visions which apply to all mines and which should be embodied in the mining codes of all States. Undoubtedly, these standardized safety requirements would be opposed by a consider- able part of the industry, but the ultimate effect would be beneficial to the owners, work- ers, and the general public. For many years progressive mining companies in the United States have not been satisfied to operate only within the meager safety requirements of the State laws or regulations and have adopted additional and far more effective safety procedure of their own, although com- plying also with the State laws and regulations. As a result of this forward-locking policy, zany of these companies have made astonishing progress in the reduction of accidents.

Dec 1, 1935

By M. J. Ankeny, J. J. Forbes

Several sets of questions and answers on the fundamentals of first aid to the injured, based on the Manual of First-Aid Instruction of the United States Bureau of Mines, are now in use in various parts of the United States. Persons experienced in first-aid instruction believe that a standardized set of questions and answers will assist materially in preparing men for examin- ations conducted by the Bureau for first-aid certificates. Inquiries as to whether a set of standardized questions and answers is available have been made frequently by those training men for the Bureau of Mines examination for certificates. It is believed that the following list of 171 questions and answers com- piled directly from the manual will be useful to company officials and em- ployees who are engaged in cooperative first-aid training to qualify for Bureau of Mines certificates. The list may also be used by field men of the Bureau in training instructors preparatory to a cooperative training campaign and in examining classes or individuals for first-aid certificates. The page references in parentheses refer to pages in the Manual of First-Aid Instruction.

Oct 1, 1935

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By John P. McDonnell

This U.S. Bureau of Mines report describes the results from an in-mine investigation of an alternative longwall gate road design. The coal mine operator modified the pillar layout (reversed the location of the big and small pillars) in a portion of a three-entry longwall gate road area. The modified pillar layout was an attempt to reduce stress and, subsequently, stress-related ground control problems (cutter roof and dynamic floor heave events) in the tailgate region during "second-panel" mining. The results from borehole pressure cells installed in the modified gate road area showed that the ground pressures in the panel edge and adjacent small pillar were significantly reduced during second-panel mining compared with ground pressures experienced in the typical pillar layout gate road areas. The reduced stress levels around the tailgate entry adjacent to the second panel, as compared with the tailgate stress levels with the typical pillar arrangement, contributed to improved tailgate ground conditions in the test pillar zone.

Jan 1, 2010

By B. Pesic

Northwest Alloys, a wholly owned subsidiary of Alcoa, produces magnesium from dolomite by reduction with ferro silicon and aluminum. This process produces alkaline by-products in quantities that allow their consideration for use as commercial by-products. Two such products are dicalcium silicate slag, Di-Cal, and magnesium oxide condensate, MgO. The alkaline properties of these materials offer acid neutralizing capability comparable to the traditionally used lime, therefore, warranting a study for their use in applications where the neutralization of acidic waters or process solutions is required, such as treatment of mine waters. In this ongoing study, three mine waters (Bunker Hill Mine, Berkeley Pit, and Blackbird Mine) were selected for treatment with Di-Cal and MgO. Lime was used as the background control. The solid precipitates were subsequently contacted with pure water at four different pH conditions for stability testing of prepared metal precipitates (expanded TCLP). It was found that neutralization with Di-Cal results in precipitates which are of equivalent to superior stability than those from lime treatment.

Jan 1, 1999

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are in northern Saskatchewan, 11 km west-northwest of the Rabbit Lake mine. Their average grade is 1.8% UJ0 8 and they contain 6,350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende.Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest mineralizing fluids were aqueous and at temperatures of about 200°C. Ar39/ Ar40 laser age determination of illite indicates mineralization began about 1300 m.y, ago and that significant hydrothermal alteration ceased about 1170 m.y. ago though Pb/U data suggest the deposits continued to evolve into the Mesozoic.The deposits are interpreted as the result of oxidizing ground water stripping uranium and other metals from either the Athabasca sandstone, especially the heavy mineral layers, or from the regolith, and precipitating these when encountering a warm reduced fluid emanating from the basement."

Jan 1, 1984

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA USBM PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT USBM USBM USBM THIS PROGRAM CALCULATES PRESSURE LOSSES USING THE USBM METHOD GIVEN USBM IN USBH IC 7809 BY MCELROY AND KINGERY.1957. THE MAJOR DIFFERENCE USBM BETWEEN THIS PROGRAM AND THE CITED REFERENCE IS THE TREATMENT OF AIR USBM

Jan 1, 1977

By J. W. JOYCE

The Geophysical section of the United States Bureau of Mines has received many inquiries regarding the application of geophysical methods to the location of small, buried metallic objects. The object of this paper is fourfold: (1) To sketch as briefly and non- technically as possible the principles underlying the operation of several elec- trical geophysical methods of prospecting applicable to the finding of small, buried metallic objects; (2) to point out the possibilities and limitations of these methods; (3) to present, whenever possible, data showing actual results obtained from their use; and (4) to enumerate and describe methods that lack scientific background or foundation.

Oct 1, 1935