Search Documents

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By P. Stanley Jacobsen, Hemant B. Gala, Richard E. Hucko

Coal is the nation's most abundant fossil energy resource. However, its use is limited because of the nature and amount of associated impurities, such as mineral matter, sulfur, trace elements, and moisture. The moderate-to high- sulfur content of many U.S. coals is of particular concern as current and newer, potentially more stringent, regulations require reduction in sulfur oxide emissions. Release of particulates, NOx, and other pollutants during the coal-use cycle is also of concern. The current practice of controlling sulfur oxide emissions in the major steps of the coal- use cycle is limited mainly to coal preparation by physical beneficiation and, to a smaller extent, to post-utilization cleanup (flue gas desulfurization). Approximately two-thirds of the coal from states east of the Mississippi river is physically cleaned, whereas only 15% to 20% of the operating boilers in the utility industry are equipped with scrubbers to desulfurize the flue gas (Henzel, 1988). Physical beneficiation methods can be very effective in removing mineral matter, including pyritic sulfur, from coal. These processes take advantage of the differences in physical proper- ties between coal and mineral matter to achieve the separation. In a typical physical cleaning operation, raw coal is crushed to about a 50-mm (2-inch) top size. It is then screened into coarse, intermediate, and fine sizes. Crushing the coal liberates some of the ash-forming minerals, including a portion of the sulfur that is not chemically bound to the coal. The per- centage of impurities freed from the coal matrix generally increases as the coal particle size decreases. The coarse- and intermediate-sized coals are typically subjected to a cleaning pro- cess based on differences in specific gravity between coal particles and the associated impurities. Such cleaning processes used include jigs, dense-medium baths, cyclone systems, and concentrating tables. The fine-sized (typically less than 0.5-mm) coal, if beneficiated, is typically cleaned using a froth flotation technique based on the differences in surface proper- ties between coal and its associated impurities. At fine sizes, greater cleaning potential exists because a greater portion of the impurities is released from the coal matrix. However, this potential is not fully realized owing to inefficiencies in separating fine particles using state- of-the-art flotation technology. Overall, current commercial coal preparation processes are estimated to remove up to 60% of the ash and 10% to 30% of the sulfur, depending on the coal characteristics, with product weight recoveries rang- ing from about 60% to 90% and thermal recoveries of about 85% to 98% (Versar, 1985; Science Applications International Corporation, 1987; Hoffman- Muntner Corporation, 1978). For many U.S. coals, grinding to sizes finer than those used in current coal preparation plants is required to liberate most of the physically bound impurities from the coal matrix. As noted, conventional coal-cleaning methods are not very effective at these fine sizes. Accordingly, the expanded use of domestic coal requires the development of advanced coal cleaning technologies that can provide economic performance while reducing environmental impacts. Program Goals and Objectives The overall goal of the U.S. Department of Energy (D0E)'s Coal Preparation Program is to provide the scientific and engineering knowledge base that industry can utilize to produce economically competitive and environmentally acceptable clean-coal products for introduction as market conditions warrant. The coal preparation process(es) should remove undesirable components from coal and improve its handling characteristics, thus making the product coal technically, as well as economically, viable as a competitor with petroleum-derived fuels and natural gas, and with alternative environmental control technologies. The coal preparation process must be applicable to a wide variety of bituminous and low-rank coals. The cleaning process should reduce the variability among clean-coal products from various raw coals, thus significantly increasing the range of potential end uses for each raw coal. To the extent that deeply cleaned coal products have greatly reduced levels of

Jan 1, 1988

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By L. O. Storey

The McDermitt mine was found as a separate mercury ore-bearing occurrence approximately 305 m (1000 ft) northeasterly and in a different geologic setting from the old Cordero mine, which had been the district's major producer. The following briefly describes the discovery of the new deposit and the Placer Amex lnc. involvement. The Cordero mining property was under lease by Sierra Mineral Management from the owner Fred H. Lenway in February 1971, when the property was brought to the attention of Placer Amex Inc. (known at that time as American Exploration and Mining Co.) by Richard F. Hewlett of Sierra Mineral Management. The property was first examined by Amex geologists in the spring of 1971, who reported favorably on the project. During that year, Sierra Minerals Management had retained Dr. Larry Walters as a consultant. He proceeded to drill test mercury soils anomalies which he had found northeast of the old Cordero mine in an area overlain by recent alluvium and gravel. An area known as the D area was subsequently blocked out and ascribed a tonnage of about 18 1 kt (200,000 st) which occurs in the vicinity of the eastern edge of the currently defined McDermitt ore body. This mineralization was found in flat lying mercury-bearing lakebeds, unlike the steep structurally controlled ore which was mined in the old Cordero mine. It became apparent to Placer Amex that since the chances of much more extensive ore were good in such a geologic environment, additional exploration was warranted. A joint venture was formed in October 1972 by American Exploration and Mining Co. and Sierra Mineral Management to further explore the Cordero property. The project exploration was fully funded and managed by Amex. Sampling began by Placer Amex in the D area where an open trench had exposed the lakebed ore. Visible cinnabar could not account for the high-grade mercury assays taken from the trench, and an unknown mercury mineral was suspected. Subsequent work established the presence of a chlorine-bearing mercury sulfide which may have enriched the lakebeds as a secondary supergene mineral. Early identification of the mercury-bearing mineral corderoite (Hg3Cl2S,) aided in the geologic concepts for the ore occurrence and was helpful in exploring for the expansion of the D area. Corderoite was found occurring with cinnabar in the lakebeds, and in places it is a major contributor. Specimens of the unique ore were given to Dr. Eugene E. Foord and Dr. Pieter Berendsen at Stanford University, who subsequently identified the chemical and crystallographic makeup of the new mineral and described it for the first time as a naturally occurring substance. Metallurgical work on mercury recovery from the newly described mineral was carried out by the Placer Development Ltd. laboratories in Vancouver, and an acceptable recovery system was worked out together with a planned mill design. Step out drilling from the D area by Placer Amex Inc. encountered extensive flat lying lakebed ore. The McDermitt ore body, as subsequently defined by drilling, was found to contain 2.7 Mt (3 million st) of open pittable ore, containing approximately 5 kg/t (10 lb per st) Hg. The ore body gently dips to the north and is found lying mainly in claybeds just above an opalite breccia blanket which overlies the earlier volcanics. Some ore is also found in the opalite breccia. The mine and mill were constructed under an operating joint venture with Placer Amex Inc. and Sterling Mineral Ventures, and production began in June 1975 at the rate of 20,000 flasks per year. The mine is currently in progress.

Jan 1, 1985

By M. R. Tek, F. F. Craig, J. O. Wilkes, C. S. Goddin

The waterflood performance of a water-wet, stratified system with crossflow is computed by a finite difference procedure. The effects of five dimensionless parameters on tile oil displacement efficiency, water saturation con-tour.7 and crossflow rates are evaluated in the absence of gravity forces. Crossflow due to viscous and capillary forces is shown to exert a significant effect on oil recovery in a field-scale model of a two-layered. water-wet sandstone reservoir. The crossflow is at a maximum in the vicinity of the front advancing in the more permeable layer. Under favorable mobility ratio conditions, the comparted oil recovery with crossflow always is interrnerliate between that predicted for a uniform reservoir and that for a layered reservoir with no crossflow. INTRODUCTION The important erects of reservoir heterogeneity on waterflood performance are commanding increased attention in the technical literature. Much of this attention is centered on two categories of layered reservoirs: those in which layers are non-communicating and those in which crossflow of fluids occurs between the layers. In the first category, the reservoir is assumed to consist of discrete layers, each uniform within itself and differing from the others only in such properties as thickness, porosity and absolute permeability. The performance within each layer is calculated by one-dimensional flow theory, and the performance of the total reservoir is obtained by summing individual layer performances. Capillary and gravity effects usually are not considered. Representative publications dealing with thi5 type of reservoir are those of Stiles,' Dykstra and Parsons,' Hiatt,3 Warren and Cosgrove' and Higgins and Leighton." Prediction of performance for reservoirs in the second category is considerably more difficult since viscous, capillary and gravitational forces all play important roles in causing crossflow between layers. A number of authors have investigated the simpler problem of two-dimensional displacement flow in a stratified system with a mobility ratio of unity and negligible capillary and gravity effects.'; Others have considered two-dimensional, non-steady-state flow of a single, slightly compressible fluid in a stratified reservoir. A limited number of laboratory oil displacement tests in layered models with crossflow have been reported. Miscible floods (with resultant zero capillary forces) in layered five-spot models were conducted by Dyes and Braun," who studied the effect of mobility ratio with zero gravity forces, and by Craig et al. 12 who studied the effect of gravity forces at constant mobility ratio. Waterfloods in layered five-spot models (with cross-tlow due to capillary, viscous and gravity forces) were conducted by Gaucher and Lindley,"' who showed the effect of gravity forces in causing underrunning of the injected water and by Carpenter, Bail and Bobek, 14 who demonstrated the reliability of Rapoport's" dimension-less parameters for scaling layered systems. Waterfloods in rectangular layered models were conducted by Richardson and Perkins."' who investigated the effect of velocity at constant mobility ratio and with zero gravity forces, and by Hutchinson," who studied the effects of varying mobility, layer permeability and layer thickness ratios. The differential equations which rigorously describe waterflooding in a heterogenous porous medium are non-linear and do not facilitate analytical solution. By using finite difference approximations it is possible to obtain a solution to any desired degree of accuracy. Such a solution, using an alternating direction implicit procedure (ADJP), is described by Douglas, Peaceman and Rachford.18 In the present study, a computer program using ADJP explores systematically the effects of important parameters on waterflood performance of a two-dimensional, two-layered, field-scale model of a water-wet sandstone system. Particular attention is given to evaluation of the water saturation contours and crossflow rates at the interface between layers to gain improved understanding of the crossflow mechanism. PROCEDURE BASIC: FLOW EQUATIONS The basic flow equations for two-dimensional, two-phase, immiscible, incon~pressible flow in a porous medium are:

Jan 1, 1967

By D. S. Rowley, F. C. Appl

Assuming that rock behavior, during cutting with a single diamond, may be approximated by that of a rigid, Coulomb, plastic material, a theory of single diamond cutting action has been developed. Using this theory, the stresses on the diamond cutting surface and the components of the cutting force have been determined. Theoretical results agree reasonably well with available experimental data. The theory of cutting of single diamonds may be used as the basis for subsequent study of the perfonnance of surface set diamond drill bits and other surface set diamond cutting tools. INTRODUCTION For more than twenty years, surface set diamond bits have been used successfully in the mining and petroleum industries to drill and core rock formations that range from medium hard to the hardest known formations. Most extremely hard rock formations cannot be economically drilled or cored by any other means. In view of the growing use and importance of surface set diamond drill bits, it is reasonable to study the way in which these tools cut, and the factors that influence wear of the diamonds. Such knowledge will contribute to better bit design and will improve operating procedures. To analyze the cutting performance of these tools it is appropriate to consider the way in which an individual diamond cuts. Once this is established, the over-all performance of the bits can be determined by considering the total effect of the individual diamonds. In recent years there has been a growing interest in rock mechanics and there now exist several publications dealing with the deformation and failure of rocks. Notable experimental work has been reported by Bredthauer,1 Handin and Hager,2, 3 and Gnirk and Cheatham.4 An extensive collection of data pertaining to rock properties at low confining pressures has been given by Wuerker.5 Cheatham and Gnirk have recently presented an excellent review of the state of knowledge regarding analytical and experimental rock deformation and failure.6 Generally rocks are extremely weak in uniaxial tension, and weak or only moderately strong in uniaxial compression. Both tensile failure and compressive failure are generally brittle in nature. This means that there is little or no deformation or "flow" of the material before shear or tensile fracture occurs. Thus, until fracture occurs, rock behaves very nearly like an elastic material in uniaxial stress. Significant changes in behavior of rock occur under conditions of triaxial compressive stress. There is generally a marked increase in compressive strength and in ductility. It has been demonstrated that the failure becomes plastic (in a macroscopic sense) at sufficiently high values of confining pressure. Sharp wedge chisel indentation studies conducted by Gnirk and Cheatham indicate that many rocks behave in a plastic manner at relatively low triaxial compressive stress states.4 If "failure" under triaxial compressive conditions is considered to be either complete rupture or macroscopic plastic flow, then the general failure characteristics of a rock can be reasonably well represented by the commonly known Mohr envelope. This certainly is not a perfect failure criterion (since the effect of the intermediate principal stress is neglected) but it has been found to be adequate for most engineering purposes. Mohr envelopes usually are constructed graphically using experimental triaxial test data. For purposes of analysis it is convenient to represent the envelope in equation form. Among the several approximate forms appearing in the literature, a parabolic form is suggested by Cheatham,7 and an exponential form is suggested by Paone and Tandanand.8 The exponential form has been adopted for this study, and based on published data, appropriate parameters have been established for 19 rock types. A typical plot of the data compared with the approximate envelope, and a summary of the rock properties and

Jan 1, 1969

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn's temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By J. S. Kirkaldy, D. H. Weichert, G. R. Purdy

Two-phase diffusion couples have been used to simulate the growth of proeutectoid ferrite in ternary Fe-C-Mn austenites. It has been shown, theoretically and expermentally, that the results fall into two classes: a high-super saturation class in which the major role of manganese additions is to influence the boundary conditions for carbon diffusion; and a low-supersaturation class in which the partition of manganese is required. In the latter case, a drastic inhibition of the reaction rate is to be expected. As an aid to the kinetic analysis, a portion of the iron-rich comer of the Fe-C-Mn constitution diagvam has been determined. The conclusions drawn from this work have a direct bearing on the kinetics of the grain boundary ferrite precipitation reaction and thus yield insight into the manner in which alloying elements can influence the rate of austenite-decomposition reactions. THE role of alloying elements in the austenite-decomposition reactions has provoked considerable interest, since it is apparent that an understanding of this phenomenon will yield insight into the harden-ability problem. In the present investigation, attention is focused upon the proeutectoid-ferrite transformation in the system Fe-C-Mn, and upon the manner in which manganese additions affect the growth rate of ferrite. When hypoeutectoid austenite is supersaturated, the ferrite first formed usually exhibits two distinct types of morphology. At low super saturations, grain boundary layers grow into the austenite grains with an approximately planar interface, and usually possess at least one incoherent phase boundary. At high supersaturations, Widmanstiitten plates appear, which bear an orientation relationship' to the parent austenite. In this case, there is a chance of partial lattice matching along the sides of the plates and an attendant semicoherent interface structure. Purdy and Kirkaldy2 have used a two-phase binary Fe-C diffusion couple to demonstrate that carbon volume diffusion controls the incoherent reaction, while Rouze and rube,' using thermionic-emission microscopy, have shown that the thickening of Widmanstatten ferrite plates is appreciably slower than expected for carbon-diffusion control. This suggests that the plates are bounded by partially coherent, low-mobility interfaces. The redistribution of alloying elements during transformation has been the object of studies by Aaronson4 and owmman,5 who have shown that no alloy partition occurs during ferrite precipitation in the systems Fe-C-Cr and Fe-C-Mo, respectively. More recently, Aaronson et al.6 have shown that some manganese partition occurs at low super-saturations in the system Fe-C-Mn, but that no partition occurs at higher super saturations. Pickle-simer et al.7 observed that no manganese partition occurred during the early stages of the pearlite transformation in a manganese steel, and concluded that volume diffusion of the alloying element is not the rate-deter mining factor. The diffusion coefficients pertinent to this investigation have been measured by Wells, Batz, and Mehl8 (carbon in austenite), R. P. smith9 (carbon in ferrite), Wells and Mehl 10 (manganese in austenite), and Kirkaldy and Purdy11 (diffusion of carbon on a manganese gradient in austenite). Kurdjumov 12 has shown that the diffusivity of substitutional elements in ternary austenites up-quenched from martensite may be greatly enhanced, due, apparently, to the presence of a persistent defect structure. The recent work of Krauss 19 showing high densities of tangled dislocations in reversed Fe-Ni martensite is in agreement with this conception. THEORETICAL Diffusion in ternary or higher-order systems may be described with the aid of Onsager's extenbion of Fick's first law,14 in which the flux of each of the n components is assumed to be a linear function of all concentration gradients:

Jan 1, 1964

By C. C. Martin, M. C. Fuerstenau, R. B. Bhappu

Experiments revealed that quartz could not be floated in conductivity water at any pH with a long-chained sulfonate as collector. Various cations, Fe+++, Al+++, Pb++, Mn++, Mg++, Ca++, are shown to function as activators when the pH is such that the cation hydrolyzes. As the solubility product of the various cation-sulfonates was exceeded at the concentrations involved, precipitated cation-hydroxy-sulfonates, e.g. Fe (RSO3)2OH must be functioning as the collector in these systems. A number of interesting and important phenomena were revealed during a study of the response of beryl to sulfonate flotation.' Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH 3.0, about three ppm Fe+++ increased recovery of leached beryl from about 60 pct to 100 pct, whereas about four ppm Ca+ + reduced the recovery from 60 pct to 2 pct. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper Sulfonate Flotation of Beryl,' even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation-sulfonates are precipitated immediately in solution. That is, blueish-white clouds were noted to form after given additions of salts to known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe(RCO3)2OH and that bonding to the surface occurs through the hydrogen of the hy-droxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems in the presence of various cations at various values of pH. EXPERIMENTAL MATERIALS AND METHOD Sodium alkyl aryl sulfonate was chosen as the collector for the experimental work. The reagent, sup plied as a courtesy sample by the Shell Chemical Co., has the following physical properties: Physical form Solid — Finely ground Sulfonate content, pct wt 95 to 97 Molecular Weight 450 to 470 Number of carbon atoms in hydrocarbon chain 25 to 30 Melting Point, OF 250 to 260 Solubility Soluble in water with gel formation at concentrations higher than 25 pct by weight sulfonate This particular reagent was chosen because of its high active sulfonate content, long-chain length, and solid form. With the exception of the frother and sulfonate, all other chemicals were of reagent grade quality. Conductivity water was used in the experimental work. This water, made by passing distilled water through an ion exchange column, had an average measured conductivity of one micromho. Experiments were conducted at room temperature in a small glass flotation cell with the following procedure: 1) A redetermined amount of water and salt solution (e.g. CaC12 . 2H2O) were combined and the pH adjusted to a given value. 2) A given amount of sulfonate was added so that final solution volume was 130 cc. 3) One drop of Dow 250 frother was added. 4) Five g of quartz were added and the system conditioned for five minutes. 5) The pH of the system was measured (termed flotation pH).

Jan 1, 1963

By W. A. Riggs

In a single year the total transportation cost equals nearly 30 pct of the value of mineral commodities, the largest single cost from the deposit to consumer. The magnitude of this economic factor calls for more complete understanding of cost and operational problems between producer and carrier than now exists. Details are given of the costs of providing transportation as well as freight rates for selling transportation. In 1958, transportation of mineral commodities in the United States required 600 billion ton-miles to move 1 3/4 billion tons of products of mines comprising solid fuels, crude oil, industrial minerals and rocks, and ores. Possibly 17 pct was handled by more than one mode of transport, since combinations of several modes of transport may, at times, achieve better service/cost results than any single mode. Total transportation cost of nearly $5 billion equaled roughly 30 pct of the value of the mineral commodities, the largest single cost from the mineral deposit to the consumer. The tremendous magnitude of this transportation undertaking demands much more complete understanding than now exists between mineral producers and carriers about the economic and operational problems of each other. A substantial portion of the daily work of the writer is spent in trying to act as a combination interpreter and catalyst between potential shippers and carriers, hoping to direct both to points of mutual understanding and advantage. For the purpose of this paper, it is necessary to ask mining people to accept some terminology and to try to appreciate the mental approach of the freight rate making people of the carriers. This paper will consider costs of providing transportation as well as freight rates for selling transportation—although these are fields of limited certainty. There are no accurate statistical breakdowns for all modes of transport and types of carriers indicating commodities, volume of traffic, distances, costs, and rates. Much information is available for railroads, and some for the regulated portions of air, motor, pipeline, and water transportation. Unregulated carriers, handling about half of the transportation of products of mines, are not required to report, and very little is known of their activities. Figures used herein are national in scope, unless otherwise indicated, and have generally been derived from Interstate Commerce Commission reports and files. Tonnage figures have been reduced to net tons of 2000 lb. The very generalized comparison of average mileage freight rate levels for various modes of transport provided by Fig. 1 affords advantageous perspective for the entire field of transportation costs. Dashed guide lines show cents per ton-mile, and dotted guide lines show percentage of first class railroad freight rate. While costs of other than railroad transportation more nearly follow constant cents per ton-mile functions, costs of railroad transportation show characteristic taper, or decrease in cents per-ton mile with increasing length of haul. This fundamental difference in cost is due largely to the fact that railroads and pipelines provide their own fully taxed roadway facilities while highway, waterway, and air carriers use government-provided tax-free roadway at no cost other than fuel, license, and certain excise taxes. Thus railroad and pipeline transportation might be said to carry heavy threshold costs in addition to those transportation costs which are directly variable with ton miles of transportation produced. The original basis of railroad freight rate structures lies in the classification of all articles of commerce into railroad class ralings ranging from 7 to 40 pct of first class (100 pct) rate level, dependent on value, hazard, loading characteristics, service requirements, and whether carload or less than carload. Classification tables and mileage-based (but arbitrarily grouped), rate scales are published as tariffs subject to approval by regulatory bodies. Used together, these determine class rates in cents per 100 lb between points in the U. S. Where local commercial or operating conditions render it advantageous for carriers to depart from

Jan 1, 1961

By D. C. Jillson

WORK in recent years1-' has indicated a complexity of the processes of deformation of metal crystals not previously appreciated and not fully accounted for by any hypothesis so far advanced. Furthermore, the nature and mechanism of formation of nuclei of recrystallization have not been determined precisely. The deformation of single crystals of zinc has been studied frequently, but the purity of the zinc and the perfection of the specimens sometimes have been given little consideration. Methods have been developed recently that readily yield zinc single-crystal specimens of high quality.5 In the present work, such specimens were deformed in various ways under various conditions, and deformed specimens were annealed to obtain information regarding recovery, recrystallization, and grain growth. The paper attempts to correlate and evaluate previous data, as well as to present new data, in order to determine areas in which more detailed work might be done most profitably. Tests at temperatures from the freezing point (419.46°C) to room temperature revealed glide only on basal planes in a close-packed direction (100)*, as reported by Mark, Polanyi, and Schmid6 and others. Markings probably similar to those observed by Kolesnikov7 and Boas and Schmid8 were noted in specimens stretched at elevated temperatures, but it seemed clear that these were not caused by prismatic or pyramidal slip (see second paragraph of section on Phenomena Involving Bending of the Basal Plane). Twinning Twinning on the octahedral plane of a face-centered cubic metal has been pictured as a process of simple homogeneous shearing along that plane in a [112] direction. It was recognized by Mathewson and Phillipsv and others""" that the (102) twinning of zinc required a somewhat more complex mechanism and might be considered as a homogeneous shearing of (102) planes in a [211] direction plus slight adjustments of atoms to positions of greater stability or lower energy, or as a single movement of each of the atoms in the same sense into the final positions. Gough and Cox" modified Mathewson's mechanism to obtain a more stable lattice configuration, but it is not clear that they succeeded, and their mechanism requires movement of some of the atoms in a sense opposite to that of the overall twinning movement. They also suggested that twinning may occur as a result of previous basal slip. This conclusion was based on the observation that twinning caused by alternating torsion was clearest and most profuse at positions for maximum basal slip rather than for maximum stress on (102) planes in the close-packed direction (not the twinning direction), and no mechanism was described. It might be wondered whether resolution of stresses on the twinning plane in the twinning direction would have afforded a simpler explanation. If twinning is essentially a simple homogeneous shearing along the twinning plane, it would seem that twins should grow by a smooth, continuous mechanism, and, indeed, that a simple reversal of stresses should reverse the shearing and de-twin the crystal. Cylindrical tablets 1/8 to 1/4 in. thick were cleaved from singlle-crystal specimens and were squeezed, perpendicular to a second-order prism plane, to give a tensile stress perpendicular to a first-order prism plane. A "click" was heard and a thin, needle-like twin appeared on the basal cleavage face. If squeezing was continued smoothly, the twin, viewed at magnifications up to X500, grew smoothly and quietly (fig. 1). X-ray examination verified that the twinning was of the (102) type. Rotating the compression axis 90" to reverse the stress then caused a smooth, continuous shrinkage and ultimate disappearance of the twin (fig. 2). The squeezing also caused a rumpling of the basal

Jan 1, 1951

By J. Weyer

"A lot of incorrect, dangerous and misleading statements about the effect of CO2 on the human body can still be found in the internet, the media and in books. It is a fact that already low concentrations can lead to critical reactions, higher concentrations cause a narcosis. The real effect is not a lack of oxygen but an inner suffocation. The breathing reflex is decreased and the transport of oxygen in the blood is reduced due to a low pH value of the blood. Furthermore a reduced oxygen content in the air can also lead to the failure of diesel engines. MOTIVE Different gases can appear in active mines as well in abandoned mines, adits and caves. The most dangerous gases are CO, NO/NO2, H2S, SO2, CH4 and CO2. Although the general danger arising from these gases is mostly known some aspects are underestimated. Furthermore misleading or wrong statements exist about the detection and the effect of gases on the human body. This is especially true for CO2. In the last years a couple of accidents happened with a great number of injured persons and unfortunately also some fatalities. As a result wrong information and comments about the effect of CO2 have been published in the media. A huge unexpected CO2 outburst in a potash mine showed again some additional problems and limits for rescue troops. ORIGIN OF CO2 AND MISLEADING STATEMENTS ABOUT THE EFFECT ON THE HUMAN BODYCarbon dioxide can appear as free gas in the earth crust. It is especially known in significant concentrations in some potash deposits, in hard coal mines and some caves. Furthermore it can be formed due to complete oxidation of carbon. It can appear in technical processes. It is also used for or in technical processes, as fire extinguishing agent, as cooling agent, it is contained (added) in sparkling water or other soft drinks and it is formed by fermentation processes. Up to today a lot of wrong information about the effect of CO2 on the human body is published or is still in the mind of many people and unfortunately even in the mind of members or leaders of rescue troops. On August 16th 2008 a faulty CO2 extinguishing installation in the city of Mönchengladbach/Germany caused the injury of 107 people and the evacuation of further 150 people /1/. People on the streets became unconsciousness and felt down. Fortunately all could be rescued due to the immediate rescue operation of local fire fighters. Furthermore the CO2 concentration on the ground was diminished by help of a helicopter. What could have happen with the engine will be discussed later. After 6 days a second similar accident took place /2/. In the news members of the rescue teams explained that CO2 leads to suffocation due to a lack of oxygen. This is wrong! Also cave explorers often say that a burning candle can detect a low oxygen and/or high Carbon dioxide content in the air. This is also wrong and deadly dangerous! Similar statements we find nowadays in the internet /3, 4 and many other/. In a forum “science and mathematics > chemistry” several people say that winegrowers go with a candle into the vine-cellar to detect CO2 /5/. Again: this can be deadly! Another dangerous statement is that CO2 in higher concentrations leads to headaches so people should leave such areas. A last example found in the literature is that at 3 % the breathing volume is doubled and at a concentration of 20 % one can felt some warmth on the skin. Both is not wrong but can lead to false conclusions. /6/"

Jan 1, 2015

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube's rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir' interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir's principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-' with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By C. H. Li, R. J. Stokes, T. L. Johnston

The phenomenon of solid-solution strengthening has previously been studied in a number of binary alloy systems.1-8 There has been, however, very little information published concerning the strengthening effects of specific solutes in magnesium alloys. Schmid and his coworkers9,10 investigated the behavior of aluminum and zinc in binary and ternary magnesium-alloy single crystals, but this work was done before high-purity materials were readily available. Workers at the Dow Chemical companyH reported increases in the critical resolved shear stress upon alloying magnesium single crystals with zinc and indium. Recently, Hardie and parkins* investigated the extent of hardening produced by the addition of various solutes to poly crystalline magnesium. The present work was undertaken to provide data on the strengthening effects of a number of solutes in high-purity magnesium, for the purpose of supplying further experimental information which might be useful in describing a general mechanism for solid-solution strengthening. To simplify interpretation of the results, the mode of deformation was limited to basal slip, through the use of single crystals. EXPERIMENTAL PROCEDURE Magnesium and magnesium binary-alloy single crystals containing indium, cadmium, thallium, aluminum, and zinc were prepared in the form of l/2-in.-diam rods, approximately 8 in. long, using a modified Bridgman technique in which the crystals were slowly cooled from the melt in a steep temperature gradient, in an atmosphere of helium. It was found that a solid-liquid interface travel speed of about 0.7 in. per hr consistently produced single crystals. The poly crystalline starting materials for the preparation of single crystals consisted of 1/2-in.-diam extruded rods, prealloyed to the desired composition. The unalloyed magnesium and magnesium-indium extrusions were furnished by the Dow Chemical Co. The other alloys were prepared at the Rensselaer Polytechnic Institute Metallurgical Laboratories. Some preliminary studies of the strengthening effect of indium were conducted at room temperature using a constant rate of tensile loading of 1040 g per min. Stress was applied to the crystals by means of a simple 5:l lever arm. The lever was loaded by a constant rate of flow of shot into a receptacle suspended from the long arm of the lever. Plastic flow was detected by an electrical resistance strain gage cemented to the surface of the crystal normal to the minor axis of the predicted glide ellipse. The crystals were acid machined to produce tensile specimens with a reduced section between the grip ends, with an additional step in the center of the reduced section to compensate approximately for the slip-retarding effect of the strain gage. The balance of the single crystals were extended in an Instron tensile tester. This machine employs a synchronously driven screw and automatically records applied load as a function of cross-head separation. It became unnecessary therefore, to employ a strain gage to detect deformation or to acid machine a reduced section. Preparation for testing reduced merely to chemical cleaning of the surface, thus minimizing the amount of handling and probability of accidental damage to the crystals. The rate of elongation employed in all the tests was 0.002 in. per min, corresponding to a strain rate of approximately 0.0004 per min. EXPERIMENTAL RESULTS The investigation confirmed the finding of many workers that the yield strength of hexagonal metal crystals is strongly orientation-dependent. This is illustrated in Fig. 1, in which o, the tensile stress required to produce gross plastic flow in eleven unalloyed magnesium crystals stressed at a constant rate of loading is plotted as a function of sin X, cos Ao where X, is the angle between the

Jan 1, 1960

By James M. Barker, Richard O. Y. Breese

The recognition of perlite as a distinct volcanic glass, and of the arcuate fractures that often characterize these natural glasses, dates back at least to the late 19th century and perhaps into the 18th century (Howell, 1974). Some authors suggest that recognition of perlite dates considerably further into antiquity, perhaps to the 3rd century BC (Caley and Richards, 1956). Most recent definitions identify perlite by the presence of vit¬reous, pearly luster and by the presence of characteristic concentric or arcuate perlitic fractures. As discussed more fully below, arcuate fractures in perlite need not be megascopic. The textures of perlite which commonly occur in deposits range from dense to highly vesiculated to pumice-like. Thus, the classical definition of perlite is descriptively restrictive compared to the natural range of textures and neglects to address the issues of genetic origin and geologic occurrence. In spite of the petrological usage of the term perlite, the in¬troduction of expanded perlite aggregate into industrial markets caused the term to be applied as well to the lightweight, cellular aggregate that is produced through the rapid thermal expansion of milled perlite ore. Perlite is distinguished petrologically from other natural glasses by a silicic or rhyolitic composition by the presence of 2 to 5 wt% total chemical water held within the glass structure and often by the presence of pearly luster and onionskin-like perlitic fractures. Worldwide, occurrences are associated with Tertiary through early to middle Quaternary volcanics and with the glassy portions of silicic domes and flows, with vitric tephra, with the glassy chill margins of dikes and sills, and with the glassy portions of welded ash flow tuffs. Less commonly, perlite is reported in association with the glassy portions of volcanic plugs and lacco¬liths. The perlite carapaces that partially or fully comprise extru¬sive domes and flows are often thick and areally extensive, and thus provide commercially attractive targets for low cost open pit mining. Perlite tuffs and tephras are also important commercial sources. Mining costs are minimized by open pit quarrying and by either bulldozer ripping or blasting. Crushing and sizing facilities are generally close to the pits. Due to the low weight and large volume of expanded perlite, unexpanded perlite that has been crushed and sized is usually shipped nationwide directly to local markets where it is expanded and processed for distribution to end users. The vast majority of international trade is in unexpanded perlite. In the United States, the evolution of the expanded perlite industry can be traced to the late 1930s and early 1940s when expanded perlite aggregate was introduced into gypsum plaster and concrete markets as a substitute for vermiculite (Schundler, Jr., oral communication, 1991) and was promoted for use in a much broader spectrum of products (Howell, 1974). By the early 1950s, end user markets were well established and small expanders were numerous east of the Mississippi River. Today, mining and expan¬sion is undertaken throughout the world. Worldwide production of perlite is dominated by the former Soviet republics, the United States, and Greece. Total worldwide production of processed perlite during 1990 is estimated at roughly 1 778 000 tons (Davis, 1991). The physical properties of expanded perlite that give this prod¬uct unique commercial value include: low bulk density, chemical inertness, high insulating ability, nonflammability and fire resis¬tance, and its ability to retain water. These and other physical properties give expanded perlite value in such uses as: lightweight acoustical and thermal insulating aggregate; component in plaster, insulating cements and lightweight concrete; loose fill insulation; as aggregate in horticultural applications; and in milled form as filter aid. In the United States and Europe, the largest end use is within building construction products.

Jan 1, 1994

By C. D. Stahl, R. Sandrea

This investigation was made to evaluate the comparative effects of the viscosity and the phase behavior of the buffer fluid in the composite solvent displacement of Bradford crude from waterflooded sandstone cores. Buffer slugs of propane, naphtha and other refined hydrocarbons exbihiting increasingly favorable viscosity ratios and decreasing solubility relationships, respectively, with Bradford crude, were used in long Berea sandstone cores. The secondary slug was isopropyl alcohol. The results indicate that higher oil recoveries are obtained for increasingly favorable phase relationships even when these are accompanied by unfavorable viscosity ratios within the range studied. Moreover, when propane is used as a buffer slug with an adverse viscosity ratio of 36, it gives higher oil recoveries than at a similar size slug of an any1 alcohol having a viscosity ratio of 1.09. The investigation was extended to the study of the effect of flooding rate on oil recovery. Residual Bradford crude was displaced from a 6-ft Berea sandstone core at rates varying from 0.3 to 30 ft/ day. The results show that as flooding rates were increased above or decreased below a minimum range of 1 to 2 ft /day, displacement efficiency increased considerably. INTRODUCTION In recent years, the alcohol slug process as a means of tertiary recovery has been the subject of many investigations. Gatlin and Slobod showed the advantages of the combination solvent slugs over the previous single-slug process.1 The combination slugs require less total slug material to obtain similar oil recoveries. The basic combination process involves injecting a primary or buffer solvent which is preferentially oleophilic, followed in turn by a water-driven slug of isopropyl alcohol. This procedure ensures that the buffer slug, which is miscible only with the reservoir oil, displaces and replaces the oil and is in turn displaced, together with the water, by the isopropyl alcohol slug miscible with both fluids. Likewise, for those reservoir oils that show some degree of phase incompatibility with isopropyl alcohol, as does Bradford crude, a proper buffer solvent can artificially make the alcohol process technically feasible. From an economic standpoint, propane or LPG would be the most appropriate primary solvent to be used in the field; however, Taber, et a12 have indicated that the alcohol process becomes highly inefficient in the displacement of light hydrocarbons because of the entrapment of these hydrocarbons during the stabilized bank formation. Moreover, since materials such as propane have such low viscosities, adverse viscosity ratios with most reservoir oils would be penerated, thereby possibly further reducing the efficiency of the buffer solvent. This paper presents the results of an experimental study of the comparative effects of viscosity ratio and phase relationships on the displacement efficiency of Bradford crude by means of dual solvents. The work was extended to include the effect of flooding rate on oil recovery. Rates within the range of field and laboratory values were used. EXPERIMENTAL PROCEDURE APPARATUS The porous media used in this study consisted of two 10-ft and one 6-ft Berea sandstone cores, 3-in. in diameter. These were cast in galvanized steel pipe of 31/2-in. ID and the annulus was filled with Armstrong cement. The 10-ft cores were assembled by connecting two 5-ft units, which were joined together by 8-in. steel flanges fitted to the pipe. Intimate contact between the two sections was obtained by inserting a thin disk of the same sandstone between the core faces. The outlet and inlet ends of the cores were covered with threaded pipe caps. The injected fluid was gravity fed to two variable-rate positive-displacement pumps. The fluids were filtered before entering the core and the effluent was collected in an automatic fraction collector and

Jan 1, 1966