Search Documents

By Vito J. Colangelo

The primary object of this study was to determine the effect of ferrite and its orientation upon the mechanical properties of a precipitation -hardening stainless steel with particular attention to the short-transverse properties. The investigation consisted of Jour major parts : the preliminary investigation of billet properties, the effect of forging reduction and ferrite content upon mechanical properties, the effect of notch orientation upon impact strength, and the relationship of heat composition to ferrite content. Low ductility and impact strength in the short transverse direction were found to he associated with the orientation and shape of- the ferrite plates. It was also determined that impact strength varied with notch orientation. The test values obtained with the notch perpendicular to the plane of the ferrite plate were lower than those obtained in the notch-parallel condition. The over-all investigation showed that high ferrite contents in general had a deleterious effect upon mechanical properties and that the ferrite content could he minimized by exercising rigorous control of the heat composition. A careful balance of elements, nitrogen in particular, must he maintained in order to reduce the formation of ferrite. THE precipitation-hardening stainless steels were developed to fulfill a need for high-strength corrosion-resistant alloys. In the annealed condition they are soft and ductile and possess many of the desirable characteristics of the austenitic stainless steels. In the hardened condition, the alloys exhibit the high strength and hardness of the martensitic stainless steels. The alloy under consideration in this investigation has a nominal composition as follows: C Mn Si Cr Ni Mo N 0.13 0.95 0.25 15.50 4.30 2.75 0.10 The hardening mechanism is identical to that of other hardenable steels in that it depends upon the transformation of austenite to martensite. This alloy because of its annealed structure and its ability to be hardened combines the desirable forming and corrosion properties of the austenitic grades with the high hardness and strength levels attainable with the hardenable grades. The reason for this apparent duplicity of proper- ties can be explained by considering a basic metallurgical difference between the hardenable stainless steels and those of the austenitic group. Both types are austenitic at 1800°F but, while the martensitic grades transform to martensite upon rapid cooling to room temperature, the austenitic grades remain austenitic even when cooled to temperatures below room temperature. The major difference then is in the degree of austenite stability. This stability can quantitatively be described by the Ms temperature. The Ms is defined as that temperature at which austenite begins to transform to martensite. The austenitic grades for example may be cooled to -300°F without producing significant quantities of martensite. The hardenable stainless steels on the other hand have an Ms temperature in the vicinity of 400" to 700°F. In cooling to room temperature, these alloys traverse the entire Ms-Mf range and show almost complete transformation to martensite. The semiaustenitic stainless steel, however, occupies an intermediate position with respect to its austenite stability. The analysis is so balanced that the Ills temperature lies at or slightly above room temperature. The resulting alloy retains much of its austenite at room temperature and yet responds to hardening heat treatments. Achieving this delicate balance of elements is therefore of great importance. Slight imbalances of the equivalent Cr-Ni ratios frequently result in the presence of 6 ferrite. It is the effects of this ferrit with which we are concerned, more specifically the effect of the quantity and ferrite orientation upon mechanical properties, particularly ductility. PROCEDURE A) Preliminary Investigation of Billet and Forging Properties. In order to determine the effect of ferrite on billet properties, billet stock from three heats with various ferrite contents was utilized. Tensile specimens were obtained in the transverse and longitudinal directions from this material and heat-treated as shown in Tables I and 11. Forgings were made from these same heats, the purpose being to determine what effect, if any, the ferrite might have upon the mechanical properties. These forgings were made in such a manner as to elongate the ferrite in the longitudinal and transverse directions. The method of forging was as follows. A section was cut from a 6-in.-sq billet of Heat A and flat-forged to 1-1/2 in. thick. Working was done from one direction only with no edging passes as shown

Jan 1, 1965

By D. Borman

The location of underground positions in mines has usually fallen to their survey department's. Their usual tasks include: ? installation of a high-precision peg network like the National Survey grid as beacons ? offset measurements to the sidewalls, and sometimes hangingwall and footwalls, of development tunnels and excavations ? offsetting of stoping panels for the calculation of face ? advance and the square meterage of area removed. Other departments build their observations into the plans produced by the surveyors. If more precision is required, they ask the surveyors to `elevate' their points with a theodolite. Apart from the survey peg network and `elevations' these measurements are usually planer measurements suitable for producing plans, sections and projection sheets. When the only representation medium was a sheet of paper or transparency, this was perfectly suitable. However the development of CAD models of the workings has changed all this. Full 3D representation is not properly catered for in the tool sets in current use, and needless hours are spent converting analogue-type observations into digital form. The basic survey models need to be augmented by the observations of other disciplines that are also required to locate positions underground. These include: ? the need for geologists to plott their mapping and ? borehole logs into 3D space ? the need for samplers to position their sample points accurately because the geostatistical models are biased and inaccurate ? the need for stoping width recorders to position their thickness observations to prevent errant evaluation and bonuses ? the need for rock engineers to place their mappings into 3D to build true geotechnical models to manage geotechnical stresses ? the need for production officials to receive updated face ? positions during the month so that they can manage the ? production and utilize their resources properly. This paper covers a new method of positioning profiling points to a suitable degree of accuracy. I believe the method is sufficiently simple and cheap for all to use. Historical methods Platinum and gold orebodies, especially in South Africa, are generally narrow tabular deposits. This made them suitable for depicting on a 2D medium like paper. The determination of stoping or face widths was not a problem, as the ore is removed in a single stoping process. Such 2D representations could be easily positioned using tape offsetting between survey pegs or points tied in from survey pegs. Problems of dip were handled by using 'Stope Sheets' which chose a best fit projection for the whole area depicted or by using true dip section sheets for inclined tunnels. Rolling reef and potholes were the common areas of difficulty. Most mines now model their orebody and plan the extraction in computer graphics. This means that the representation of the current workings has to change to support this trend. It now becomes a truly 3D problem. Mining officials find it inconvenient to have their actual workings in single-line depictions while their orebody is depicted with top and bottom contacts and the planned tunnels in 3D shapes. Geological models which form the basis for the resource model and planning process are often out of date, as the updating process is slow. The geological mapping has to be plotted onto sections and plans. These are then digitized into graphics by a draughtsman and checked by the geologist. Only then does the interpretation and model update take place. Potential methods to create 3D 'Actuals' Global positioning systems (GPS) Surface mines have been blessed by the advent of GPS technology. These simple-to-operate pieces of equipment and compatible software make it possible for all types of mine employees to locate themselves, and therefore to locate their observations. GPS are often inexpensive and give an acceptable degree of accuracy. Only in deep pits or close to the highwalls are observations hindered. Such technology cannot however, work underground. Ground penetrating radar (GPR) GPR is reported to be very useful for estimating the positions of potholes and faults. However it is still considered as providing an estimate, not a definite measurement. GPR is good for seeing into solid rock, not into open spaces. Inertia reading devices Experiments with inertia reading devices have been conducted on the mines. They were the forerunners of GPS for military guidance systems, and were even used for city navigation in the early 70s. They do however work best with heavy or fast-spinning gyros. Anglogold Ashanti's attempt to use them were discontinued in the mid-90s when the developers asked for an additional few million rand for a device that would weigh more than 12 kg and have a limited operational life.

Jan 1, 2006

By C. G. Dunn, J. L. Walter

Secondary recrystallization to the (110) [001] texture in high-purity silicon iron occurs if low-oxygen material is annealed in a nonoxidizing atmosphere. Any departure from these conditions results in a growth of (100) oriented grains. The nature of the matrix and secondary recrystallization structures and textures and the nature of grain boundary interactions during growth show that the low gas-metal interfacial energy of the (110) surfaces provides the driving force for growth of these grains. A type of grain growth, characterized by a driving force which derives from energy differences of {hkl} surfaces at the gas-metal interface, has been treated in recent papers.&apos;-7 Secondary recrystallization to the cube text!:: in high-purity silicon iron provides one example. The present paper also deals with a surface energy driving force but the texture that results by secondary recrystallization is not the cube texture; it is a texture in which the (110) plane is in the plane of rolling and the [001] direction is in the direction of rolling. The phenomenon described in this paper is different from the impurity (dispersed phase)-controlled secondary recrystallization process in which the (110) [001] oriented grains grow under the action of grain boundary driving forces.8-12 It is also different from tertiary recrystallization,2 which also produces the (110) [001] texture in high-purity silicon iron, since the matrix textures and grain sizes are different. Finally, it is unlike any other form of secondary recrystallization reported in the literature. The possibility of obtaining the (110) [001] texture in high-purity silicon iron became clear in a study of the effect of impurity atoms on the energy relationships of (100) and (110) surfaces. In this study Walter and Dunn6 observed the migration of (100)/(110) boundaries, i.e., boundaries between two grains, one of which has a (100) plane and the other a (110) plane, respectively, parallel to the plane of the sheet specimen. At 1200°C the (100)/(110) boundaries advanced into (100) grains in a vacuum anneal, then reversed their direction and migrated into (110) grains in a subsequent anneal in impure argon. Finally, the direction of migration reversed once again with (110) grains growing into (100) grains in a second vacuum anneal. These results were explained in terms of a change in concentration of oxygen atoms at the gas-metal interface during the anneals. Thus, oxygen atoms were added to the surface during the anneals in impure argon to the point where ?100, the specific surface energy of the (100) oriented grains, was lower than ?110, the surface energy of (110) oriented grains. In vacuum, however, the oxygen concentration at the surface was lowered to the point where ?110 < ?100. Concerning the possibility of secondary recrystallization in high-purity silicon iron with a low initial oxygen concentration, the observed effect of adsorbed oxygen atoms has indicated6 that a good vacuum anneal would favor the rapid growth of matrix grains with the (110) plane in the plane of the sheet much more than grains in the (100) orientation. The growth of only (110) oriented grains of course would depend upon y110 being less than ?hkl, where hkl refers to any plane different from (110). The present paper is concerned with the application of the above ideas to secondary recrystallization to the (110) [001] texture in high-purity silicon iron. The matrix and secondary recrystallization textures and structures are defined and discussed. Observations of growth of nuclei for secondary recrystallization and of boundary interactions are included to provide direct information on the surface energy relationships between (110) and other (hkl) surfaces. EXPERIMENTAL PROCEDURE As before, 2,4-6 high-purity iron and silicon were melted and cast in vacuum to provide an alloy containing 3 pct Si with less than 0.005 wt pct impurities. The oxygen content of the ingot was lower than in previous ingots, being approximately 3 ppm (by weight). The carbon content of this ingot may have been slightly higher than was found for previous ingots. The same rolling and annealing schedule used previously2 was followed in this study to obtain samples 0.012 in. (0.3 mm) thick. These samples were electropolished prior to annealing. After rolling and polishing, the oxygen content of the material was approximately 6 ppm; material used in the previous studies contained about twice this amount of oxygen.

Jan 1, 1961

By Fred Leighton

INTRODUCTION Dynamic (seismic or microseismic) methods of determining the stability of structures in rock are based on detecting and analyzing the characteristics of seismic energy that has originated from or traveled through the rock mass. This seismic energy can be in the form of naturally occurring rock noise energy resulting from structural adjustments within the rock or can be introduced into the structure by physical means, such as by blasting or impact. In either case, the seismic energy radiating through the rock mass can be detected using standard equipment and can be analyzed by established techniques to reveal a wide variety of information concerning the condition and stability of the rock mass through which the energy has traveled. In the following sections, the basic instrumentation required for seismic and microseismic studies is described, and some of the presently used applications of these methods are discussed to exemplify the state of the art. INSTRUMENTATION Seismic disturbances in a rock structure generate two types of seismic wave radiation, body waves and sometimes surface waves, which radiate outward in all direc¬tions from the source of the disturbance. Underground mining applications are generally concerned only with discerning the characteristics of the resulting body waves, i.e., the compressional (p-wave) and the shear (s-wave) energy. As these two forms of energy travel through the rock structure, the particles of the rock mass are caused to vibrate, and the vibration character¬istics resulting from each of the two types of wave are distinct. Some important differences are: 1) Compressional and shear waves travel at different velocities through the rock structure. 2) The frequency at which each wave causes particles to vibrate is different, and may range from about 50 to 100 000 Hz. 3) The amplitude or energy level of each wave is different, with the shear energy usually being the greatest. These differences form the basis for equipment se¬lection for individual studies and for modern data analysis techniques. The following sections describe the basic equipment necessary to detect and record seismic wave energy data and show several examples of analysis procedures and how these procedures have been used. In principle, seismic equipment is very simple. It consists of a geophone (or geophones) to detect the seismic energy vibration and convert that vibration to an electric signal, an amplification system to increase the level of that signal, and a means of monitoring and/or recording the signals detected. Fig. 1 is a block diagram of a typical system. The following sections offer a very brief discussion of system components and their individual functions. A more complete discussion is given by Blake, Leighton, and Duvall (1974). Geophones The function of the geophone is to detect the vibrations caused by the passing of the seismic wave energy and to convert that vibration into an electrical signal that displays both the amplitude and frequency characteristics of the vibration. Particle motion or vibration can be quantified and measured by measuring displacement, velocity, or acceleration of the particles. Thus, there are three types of geophones: displacement gages, velocity gages, and accelerometers. The choice of gage depends on the characteristic frequencies of the seismic energy to be monitored and the sensitivities of each type of geophone. In general, displacement gages are used for low-frequency monitoring (periods to 1.0 Hz), velocity gages for medium-frequency monitoring (1.0 to 250 Hz), and accelerometers for high-frequency monitoring (250 to 10 000+ Hz). Experience has shown that in underground studies, the choice of which gage to use lies between velocity gages and accelerometers. An easy, accurate method for selection of gage type is discussed by Blake, Leighton, and Duvall (1974). Once the type of geophone has been selected for use, it must be properly installed, and in the installation procedure the most important step is insuring that the gage is firmly attached to a competent portion of the rock structure. Poorly mounted geophones may entirely fail to recognize low-level seismic signals and will distort the information from signals they do see. Amplifiers Seismic events associated with mine structures occur over a very broad range of energy which results in a broad range of geophone output levels. In general, geophone output levels occur in the microvolt to low milli-volt range, and it is necessary to amplify these signals in order to drive recording or monitoring equipment. Because either an accelerometer or a velocity gage might be used as the geophone, the amplification system must

Jan 1, 1982

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.&apos; On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.&apos; In this paper the terms "size broadening" and "strain broadening&apos;&apos; are used in the general sense adopted by warren.&apos; In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By Forrest V. Williams

The dislocatiorl and stacking-fault structuve of epitaxial GaAs1-,PX lms been examined by chemical etching. The layers were groun in the (100) direction and etch Pils were developed on (111} planes which nad been lapped and polished on the epiLaxia1 layevs. Tile effecL of the jollolcing cariables on the quality of the epilaxial layers has been examined: doping leuel, grouth rate, and composition. High stacking-faullL densilies weve found in the GuAsi_xpx layers. These are not observed in heavily dolled epitaxial layers tzar in layers with low phosphorus compositions. The dislocatiorz density in GuAsi-x px was highest at the sub-stvate- epilaxia1 layer interface. Composilion changes introduced dislocations in the epitaxial layers. ManY semiconductor p-n junction lasers of Group TIT-Group V compounds and their alloys have been reported in the past several years. Laser action at visible wavelengths in GaAsl-x,Px was first reported by Holonyak and Bevacqua. GaAs, a direct transition semiconductor which lases, and Gap, an indirect transition semiconductor which does not lase, form a continuous series of solid solutions.2 Laser junctions can be fabricated in GaAsl-xPx crystals with phosphorus compositions up to about 40 mol pct. In addition to the production of coherent radiation in these crystals, the efficient recombination radiation of p-n junctions in this material has equally important potential in the development of low-power semiconductor lamps. To achieve a high conversion efficiency of electrical to optical energy in p-n junctions in this material, the relation of physical properties of the crystal to luminescence efficiency must be better understood. Although the electrical, optical, and device properties of GaAsl -xPx junction lasers are understandably of considerable interest, the work to date indicates that the more serious problems are the chemical and metallurgical difficulties encountered in the growth of this material.3 In addition to the problems of chemical purity, crystal imperfections, such as dislocations and stacking faults, can be expected to affect both the efficiency of the radiative recombination process and the perfection of the p-n junction.3 The last requirement, i.c., that of the perfection of the p-n junction, is a particularly troublesome one in the fabrication of laser diodes. To obtain good laser diodes, the p-n junction must be flat, which permits the radiation to be reflected from the resonant cavity boundaries. Junction planarity is extremely sensitive to the crystal perfection of the semiconductor material. Also, it is known that at high dislocation densities (-105 per sq cm) it has not been possible to build laser junctions in GaAsl-xPx . Few studies have been reported on the crystal defect structure of GaAsl-,P,. The first serious study seems to be that of Wolfe, Nuese, and Holonyak,3 who examined the dislocation structure of monocrystalline bulk (nonepitaxial) material grown by halogen vapor transport. In this paper are reported some observations on the dislocation and stacking-fault structure of GaAsl_,P, crystals grown by a vapor transport process on substrates of GaAs. EXPERIMENTAL Crystal Growth. The GaAsl-xPx crystals were grown in an open-tube flow system, using two sets of reagents. GaAs, Pr(red), and HC1 were employed in one method. The transport reaction is =950JC GaAs+HC1 = GaCl +1/4As4 +1/2H2 and the deposition reaction is 2GaAs1-xPx +GaCl3 Composition control is obtained by the flow rate of the HC1 and the vapor pressure of the P4, which is maintained in a separately controlled furnace. The second method has been described by Ruehr-wein4 and utilizes gallium, AsH3, PH3, and HC1. The same transport and deposition reactions as above are involved. Composition control is obtained solely by the flow rates of the three gases involved. All of the crystals were grown on chemically polished GaAs substrates oriented on the (100) plane. The thicknesses of the epitaxial layers were typically 100 to 300p. Revealing of Dislocations. Dislocations were re-vealed on both the( 111 ) and { l l l }b faces by chemical etching. The specimen to be examined was mounted at 54.7 deg, lapped on glass with 3-p alumina, polished on cloth with 3-p diamond paste, and, to remove work damage, chemically polished at room temperature for

Jan 1, 1968

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY&apos; and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller&apos; have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.&apos; More recently, Kraft and Albright&apos; have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.&apos;&apos; Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By H. R. Cooper, T. S. Mika

T. S. Mika (Department of Mineral Technology, University of California, Berkeley, Calif.) - Dr. Cooper&apos;s attempt to establish a correlation between process behavior and operational variables on the basis of a statistical analysis after imposing a reasonable process model is a very commendable improvement on the use of standard regression techniques. However, it must be recognized that the imposition of a model has the potential of yielding a poorer representation if its basic assumptions or mathematical formulation are invalid. It appears that at least two aspects of his treatment require some comment. First, the limitations on the kinetic law where xta represents a hypothetical terminal floatable solids concentration (cf. Bushell1), should be mentioned. Most current investigations2-9 appear to utilize the concept of a distribution of rate constants rather than a single unique value, k, to describe flotation kinetics. A distributed rate constant is certainly a more physically meaningful concept than that of a terminal concentration. The study of Jowett and safvi10 strongly indicates that xta is merely an empirical parameter, whose actual behavior does not correspond to that expected from a true terminal concentration. Rather than being a strictly mineralogical variable, as Dr. Cooper&apos;s treatment implies, it apparently represents the hydromechanical nature of the test cell as well as the flotation chemistry. The extension of batch cell kinetic results to full-scale continuous cell operation is a suspect procedure if the effect of such nonmineralogical influences on x,, remain unevaluated. There is evidence that introduction of a terminal concentration is necessitated by the inherent errors which arise in batch testing and are eliminated by continuous testing methods.&apos; Possible lack of validity of the author&apos;s use of Eq. 1 is indicated by two unexpected results of the statistical analysis of his batch data. The first is the apparent corroboration of the assumption that the rate constant, k, is independent of particle size, i.e., of changes in the size distribution of floatable material. This assumption directly contradicts numerous results 2,4,11-l8 for cases where first order kinetics prevailed and ignores the phenomenological basis for the analysis of flotation in terms of a distribution of k&apos;s. It must be recognized that, if the rate constant is size dependent, the lumped over-all k would be time dependent; Eq. 1 would then no longer be valid. Cooper&apos;s x,, is determined by batch flotation of a distribution of sizes for an arbitrary period of time. If the size dependence of k is artificially suppressed, x,, will become a function of the experimental flotation time used in its determination. Upon reviewing the rather extensive literature concerning batch flotation kinetics, there appear to be few instances where constant k and x,, adequately adsorb variations in floatability due to particle size. The second surprising result is the low values of the distribution modulus, n, determined. Contrary to Cooper&apos;s assertion, most batch grinding (ball or rod mill) products yield values of n > 0.6, which increase as the material becomes harder.&apos;&apos; It is likely that the values of n = 0.25 and n = 0.42 for Trials 1 and 2, respectively, are completely unreasonable, and even the value n = 0.54 obtained for Trial 3 is unexpectedly low. Possibly, this indicates inherent flaws in the three trial models considered, in particular the assumed particle size independence of the rate constant, k. The above does not necessitate that Eq. 1 (and the terminal concentration concept) is invalid; it could constitute a good first approximation. However, the qualitative arguments used by Dr. Cooper in its justification are somewhat frail and require verification, particularly since much of the flotation kinetics literature is in opposition. Apparently, no effort was made to test these hypotheses on the actual data; in fact, since they pertain to a single batch test time, his data cannot be utilized to evaluate the kinetics of flotation. To evolve a control algorithm on the basis of this infirm foundation seems a questionable procedure. Another difficulty in his analysis arises in consideration of the froth concentrating process. As Bushel1 &apos; notes, for Eq. 1 to be valid it is necessary that the rate of recycle from the froth be directly proportional (independent of particle size) to the rate of flotation transport from the pulp to the froth, a restrictive condition." Harris suggests that it is more realistic to assume that depletion occurs in proportion to the amount of floatable material in the pertinent froth phase volume (treating that volume as perfectly mixed).12,21,22 The physical implications of

Jan 1, 1968

By B. J. Kochanowsky

The idea of a portable crusher is not new. Many such crushers are available but they are small and designed for construction work. For many years the author has suggested, both in this country and in Europe, the building of larger portable crushers intended expressly for use in quarries or open pits. Although not applicable under all conditions, there are mining operations where a mobile crusher arrangement could be more profitable than the facilities now used. The primary use of a portable crusher, i.e., a crusher mounted on crawlers or tires, in the rock and mining industries is to reduce costs by permitting the substitution of conveyor belt haulage for truck or track haulage. The usual sequence of operations in surface mining is drilling, blasting, loading, haulage, and crushing. Haulage is normally accomplished by truck or track-mounted cars, the latter method being used for the longer distances. However, by using a portable crusher in the pit, the sequence of operations would be changed so that the crushing stage would occur before haulage (Fig. 1). Such a sequence would permit the use of conveyors to replace the more expensive truck or track haulage methods. Since most quarry and open pit operations normally require a crushing stage, the only additional costs incurred will be due to the investment required to purchase or construct a mobile arrangement for a crusher. But this factor has to be weighed against the advantages to be gained by conveyor haulage. As shown in Fig. 2, transportation of material by belt conveyor over short distances is less expensive than by truck. The inclination of the belt has no effect on belt speed; consequently, the hourly tonnage moved remains the same. Conversely, the output rate of trucks as expressed in tons or ton-miles per shift decreases proportionally to the haulage speed, which is considerably slowed by the steepness of the road (Fig. 3, left). Although maximum possible grades and maximum economic grades of haulage are greater for a belt than for a truck (over the same total lift), the longer haulage distances favor the use of trucks. Although power consumption for hauling on a grade increases for both conveyances, the rate of power consumption increases faster for trucks than for conveyor belts (Fig. 3, right). Since the output rate and related fixed costs are affected by the travel speed, total haulage costs with trucks would increase with the grade more rapidly than the similar costs of conveyor belts (Fig. 4). Travel distance, road grade, speed, size and number of pieces of equipment, efficiency of operation, and many other factors affect such haulage costs. In general terms it can be said that the shorter the distance, the steeper the grade, and the greater the output, the more advantageous the belt becomes in comparison to truck or track haulage. In addition to potential cost savings in haulage procedures, a portable crusher would allow better utilization and performance of shovels. Loading operations would not be interrupted as often by the necessity of waiting for cars or trucks. Unfortunately, the application of belts in open pits for haulage from bench sites is generally not practical under existing conditions because a belt fed directly by a mechanical shovel can be torn, damaged, or worn out quickly by the large rock fragments falling on it during loading. However, by using a mobile crusher this situation can be avoided. As shown in Fig. 1 (b), the shovel feeds rock into the crusher located behind it. The crushed material is initially transported by an extensible and/or movable belt, thence by a longer stationary conveyor to the plant where the material is subjected to further treatment by secondary crushing, screening, etc. The first-mentioned conveyor, needed to bridge the distance between the shovel and the stationary conveyor, is necessarily variable in length owing to the continuous movement of the shovel and the desire to keep the stationary belt at a safe distance from the bench during blasting operations. The remarkable part of mobile crusher operations is the extra-ordinarily high output per man-shift, the low maintenance and power requirements for haulage, and the increased output of the loading shovel. A cement quarry which has been using a portable crusher and conveyor since 1956 requires only three men to operate the shovel and crusher and to transport the crushed rock by belt from the quarry face to the screening plant. If truck haulage

Jan 1, 1961

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,&apos; if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice&apos;s system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice&apos;s retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study&apos; of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel&apos;s Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed. Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank, or at any time in batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume1,2 or a relative concentration, which will be a function of the recovery." A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the data. One of these, the initial concentration or proportion of floatable mineral, is not necessarily equal to the feed assay because of nonfloatable oversize or locked particles." The other, a rate constant, is a measure of proportionality between the rate and the pulp property on which the rate depends. The value of the rate constant will be determined by the values of all variables which control the process and will be changed by significant changes in any of them. It is, therefore, a direct measure of performance. Where recovery or grade change continuously with flotation time, the rate constant will be independent of time and will characterize the entire course of the separation. Development of Rate Equations Rate equations can be developed either by analysis of the mechanism of the process or by direct fitting of equations to recovery-time data. Sutherland&apos;s attempt by the first method&apos; suggests that the effect of particle size variation on the rate complicates the derivation of a simple equation applicable to an ore pulp. A further problem with an ore is the concentrate grade requirement, which usually involves a variable rate of froth removal. Thus the final rate for any cell may depend on the froth character and froth height, as well as on the pulp composition. This does not imply that each cell cannot reach a steady state2 in which the rate will depend ultimately on pulp composition. The second method is the fitting of rate equations consistent with the necessary boundary conditions* to experimental recovery-time curves. On the assumption that under constant operating conditions the flotation rate is proportional to the actual or relative concentration of floatable mineral in the pulp, a generalized rate equation may be expressed as follows: Rate = Kcn [I] where K is the rate constant, c is some measure of the quantity of floatable mineral in the pulp at time t, and n is a positive number. In previous rate studies, the value of n has been taken as 1, either by direct assumption," or as a result of the hypothesis that bubble-particle collision is rate determining.&apos; A first order equation results, which after integration in terms of cumulative recovery R, leads to Loge A/A-R = Kt [2] The quantity A is the maximum possible recovery with prolonged time under the conditions used. No conclusive proof for the validity of this equation in flotation has been advanced. The evidence cited in its support consists entirely in the demonstration that it appears to apply to a limited number of recovery-time curves."&apos; It will be shown subsequently that this procedure is not sufficient to establish the order of a flotation rate equation. The possibility that the equation may be of higher order therefore requires examination. If, in particular, the exponent in eq 1 is assumed to be 2, then after integration there results R = A2Kt/1 + AKt [3] with K again a rate constant and A the maximum proportion of recoverable mineral. Eq 3 may be

Jan 1, 1952

By Jack D. Webber

The successful use of oil well packers requires, in part: an understanding of the pressures which exist at the packer in various applications and an understanding of the characteristics of the various types of packers. It is with these pressures, the resultant forces, and the characteristics of packers. that this paper is primarily concerned. An oil well packer may be defined as a mechanical device for blocking the passage of fluids in an annular space. In the more usual case, the annular space is that between the tubing or drill pipe in a well and the casing, and packers which block such an annular space are broadly referred to as casing packers. In the other case. the annular space is that between the tubing or drill pipe and the walls of an open hole, and packers for blocking this space are generally called formation packers. While the hydraulics involved are essentially the same for casing and formation packers. a greater variety of conditions are encountered in the use of casing packers and only casing packers will be discussed. After a packer has been set and a pressure seal effected between tubing and casing, the packer is comparable to a piston in a cylinder. Pressures acting upon a piston result in forces which will move the piston unless some means is provided to prevent such movement. In the same manner, pressures acting upon a packer will move the packer unless there is present a sufficiently great restraining force. PACKER CLASSIFICATIONS Packers may be classified according to the pressure conditions under which they are capable of blocking the annular space between tubing and casing. Fig. 1 shows schematically two types of packers in common use. These packers are capable of blocking the annular space against the passage of fluids under a differential pressure of significant magnitude only when the pressure in the annular space above the packing element is greater than the pressure below. It may be seen that in Fig. l-a. slips with teeth which bite into the casing and prevent downward movement are provided. In Fig. 1-h. an anchor prevents downward movement. In each case, there i-only the tubing to prevent upward movement when differential pressures act to move the packers upwardly. Packers which hold only a significant differential pressure acting downwardly have been in use since the early days of the oil industry and will hereafter be referred to as conventional type packers. In many packer applications operating conditions will 1.crult in differential pressures across the packer which will at times act to move the packer upwardly, and at other times, act to move the packer downwardly. For these applications, designs are available which will block the annular space and resist movement in either direction. Fig. 2-a shows schematically a packer of this type which is designed to be run into a well and set, and removed when desired by merely pulling the tubing. It will be noted that two sets of slips are provided-— one set above the packing element to prevent upward movement, and another set below the packing element to prevent downward movement. This packer is built around a mandrel which is essentially a part of the tubing. and which is free to move longitudinally within certain limits through the set packer. Fig. 2-b shows schematically a permanent type packer which is capable of holding pressures from either direction. Here again, two sets of slips are provided to prevenl movement of the packer. This packer is designed to become virtuallv a part of the casing when set and it is made of drillable material so that it may be drilled out when its removal is desired. The seal nipple shown effects a pressure seal between the tubing and the packer. This seal nipple is a part of the the tubing, and the nipple and tubing may be withdrawn from the well without disturbing the packer. It should be noted that these figures are not representative of all available packers which are designed to hold pressures from both above and below. Packers which resist movement in either direction will hereafter be referred to as universal type packers. There is a third type of packer in general use and this type is designed to block the passage of fluids when the pressure below the packing element ii greater than that above. This type is provided with slips which prevent upward movement of the packer and is somewhat similar to a conventional type packer run upside-down. Packers designed to hold pressure only from below are made in a variety of designs and are usually owned and operated by service companies.

Jan 1, 1949

By Jack D. Webber

The successful use of oil well packers requires, in part: an understanding of the pressures which exist at the packer in various applications and an understanding of the characteristics of the various types of packers. It is with these pressures, the resultant forces, and the characteristics of packers. that this paper is primarily concerned. An oil well packer may be defined as a mechanical device for blocking the passage of fluids in an annular space. In the more usual case, the annular space is that between the tubing or drill pipe in a well and the casing, and packers which block such an annular space are broadly referred to as casing packers. In the other case. the annular space is that between the tubing or drill pipe and the walls of an open hole, and packers for blocking this space are generally called formation packers. While the hydraulics involved are essentially the same for casing and formation packers. a greater variety of conditions are encountered in the use of casing packers and only casing packers will be discussed. After a packer has been set and a pressure seal effected between tubing and casing, the packer is comparable to a piston in a cylinder. Pressures acting upon a piston result in forces which will move the piston unless some means is provided to prevent such movement. In the same manner, pressures acting upon a packer will move the packer unless there is present a sufficiently great restraining force. PACKER CLASSIFICATIONS Packers may be classified according to the pressure conditions under which they are capable of blocking the annular space between tubing and casing. Fig. 1 shows schematically two types of packers in common use. These packers are capable of blocking the annular space against the passage of fluids under a differential pressure of significant magnitude only when the pressure in the annular space above the packing element is greater than the pressure below. It may be seen that in Fig. l-a. slips with teeth which bite into the casing and prevent downward movement are provided. In Fig. 1-h. an anchor prevents downward movement. In each case, there i-only the tubing to prevent upward movement when differential pressures act to move the packers upwardly. Packers which hold only a significant differential pressure acting downwardly have been in use since the early days of the oil industry and will hereafter be referred to as conventional type packers. In many packer applications operating conditions will 1.crult in differential pressures across the packer which will at times act to move the packer upwardly, and at other times, act to move the packer downwardly. For these applications, designs are available which will block the annular space and resist movement in either direction. Fig. 2-a shows schematically a packer of this type which is designed to be run into a well and set, and removed when desired by merely pulling the tubing. It will be noted that two sets of slips are provided-— one set above the packing element to prevent upward movement, and another set below the packing element to prevent downward movement. This packer is built around a mandrel which is essentially a part of the tubing. and which is free to move longitudinally within certain limits through the set packer. Fig. 2-b shows schematically a permanent type packer which is capable of holding pressures from either direction. Here again, two sets of slips are provided to prevenl movement of the packer. This packer is designed to become virtuallv a part of the casing when set and it is made of drillable material so that it may be drilled out when its removal is desired. The seal nipple shown effects a pressure seal between the tubing and the packer. This seal nipple is a part of the the tubing, and the nipple and tubing may be withdrawn from the well without disturbing the packer. It should be noted that these figures are not representative of all available packers which are designed to hold pressures from both above and below. Packers which resist movement in either direction will hereafter be referred to as universal type packers. There is a third type of packer in general use and this type is designed to block the passage of fluids when the pressure below the packing element ii greater than that above. This type is provided with slips which prevent upward movement of the packer and is somewhat similar to a conventional type packer run upside-down. Packers designed to hold pressure only from below are made in a variety of designs and are usually owned and operated by service companies.

Jan 1, 1949

By N. J. Peberdy, C. N. Moreton, K. C. Garner

Introduction During the past decade a major objective of the process industry has been to use digital computer technology to improve plant operating efficiencies. This objective implied some form of optimization, a concept that has various interpretations depending on the view of the prospective user. For the purpose of this paper, optimization of a process plant is defined as the establishment and setting of plant operating conditions that maximize some mathematical yield function, i.e. maximum profit, minimum residue, etc. Analysis of these objectives and the available design and implementation techniques led to the conclusion that digital computer and optimization techniques are not the stumbling blocks, but rather the development and derivation of the mathematical models of the unit operations and process plants to be optimized. Such models should not only describe the optimized (steady-state) objective, but also how one steers to this state (control algorithm). Due to the multidisciplinary nature of the skills associated with the design and operation of process plants, the development of suitable models by a single discipline, such as the process control engineer, was found to be not only difficult but often impossible, due to budget and human resource limitations. To over-come these limitations, a computer aided design (CAD) tool has been developed. It aims to provide a productivity tool to the various disciplines, at the same time coordinating the technical input from each. The system described is but the starting point in an evolutionary development of a tool that, with use, is becoming more efficient and cost effective to use. Development has become an application engineering activity rather than the preserve of the computer specialist. Project phasing The development of a mathematical description of a process plant requires coordination of information from conceptual design to operation management. The activities required to build and operate a process plant are divided into four basic chronological activities or phases. These activities are often undertaken by different organizations and disciplines. As a result, continuity is often lost with the resultant loss of critical design data. The major activities are considered to be: conceptual and flowsheeting; detailing around the P & ID; building and commissioning; and plant operation. The CAD system described provides a design tool to be used for each of these activities, as well as providing continuity between the activities and the disciplines involved. The heart of the system is the dynamic simulation of the flowsheet. Each of the activities will be discussed, leading to two simple examples that demonstrate the use of the simulator. Figure 1 shows a schematic format of the various activities and the path followed by the dynamic flowsheet simulator in the life of a project. Flowsheet development The prime requirements in the design and develop¬ment of a process flowsheet are • selection of the correct unit operations to achieve the most economic (capital and operating) beneficiation of the specified reserve ; • the sizing of the unit operations to achieve the desired results, as a function of the projected feed rates etc., to handle the time related (dynamics) of the process; and • the production of a set of engineering documents showing the drawn and labeled flowsheet with an equipment list and process specification for each of the unit operations. The question may well be asked at this stage why dynamic flowsheet simulation should be considered when steady state modeling has been found to be adequate to date. With the increases encountered in the cost of capital, one often cannot afford the luxury of designing around the compounding worst case technique. Further, a more accurate design of the control surges can be achieved. No information is lost in that the steady state solution is in fact a subset of the dynamic model. In generalized state space modeling, the differential equations describing the process dynamics are illustrated in the following matrix notation: XDOT=A.X+B.U(1) Y =C.X+D.U(2) where XDOT describes the set of first order derivatives of the system state Vector, and X- is the system state Vector; A - is the system matrix operator which in the general nonlinear case is both a function of X and time ; U- is the process input vector; B - is the input mapping matrix; Y - is the set of observations; C - is the output mapping matrix which maps X - onto Y; and D- maps the input onto the observations. Thus, by time integration of the system dynamic equations, described in (1), the dynamic trajectory away from any set of initial conditions can be deter¬mined. Further, by finding the conditions at which XDOT = 0, the steady state solution can be determined.

Jan 1, 1987

By E. B. Fitch, E. C. Johnson

The operating behavior of liquid-solid cyclones is outlined, together with the nature and range of the process results obtainable, to serve as a background for engineers wishing to consider application of this new process tool. BY now most engineers are familiar with the liquid-solid or Dutch State Mines cyclone. However, it should be helpful to know exactly what it is that the equipment does and what its limits are. Without going into cyclone theory, this paper will describe the operating characteristics of Dutch State Mines cyclones. These are manufactured under license in this country and sold under the trade-marked name of DorrClone. The physical construction of the liquid-solid cyclone has been covered in many papers,&apos;-&apos; the DorrClone in particular being described in some detail by Weems. Fig. 1 shows the unit in cross-section. The feed enters at C. The coarse, heavy particles are thrown centrifugally to the periphery and make their way down the wall to the apex where their rate of discharge as underflow is controlled by an adjustable rubber apex valve. As the apex diameter is decreased the solids build up behind the valve, producing a denser underflow. Meanwhile the fine particles are swept into the upward flowing vortex stream which exits as overflow through the vortex finder, F. Flexibility to produce the specific result desired in a particular process is achieved by providing means for varying the areas of the entrance, vortex discharge, and apex discharge. The entrance area may be varied by insertion of special shims. Vortex discharge area may be changed by use of different-sized vortex finders which are interchangeable. Similarly, the different sizes of apex valves are interchangeable and in addition each apex valve is variable down to about 60 pct of its maximum diameter. A most significant primary distinction to make is that although liquid-solid cyclones have been sometimes called thickeners, they actually are classifiers, and very potent ones. They are almost never thickeners in the special sense that many metallurgical engineers understand the term. There would be no profit in quibbling over the definition of a word, but when the application of cyclones is considered, it will help to understand the difference be- tween two mechanisms, one of which will be called classification, and the other thickening. In what is called thickening the fine solid particles present in the feed hold together by surface attraction during the sedimentation process. The loose network of particles thus held together constrains all particles to settle at approximately the same rate, the larger ones dragging the smaller ones down. As a result, pulp settles with a sharp line of demarcation between solids and a relatively clear supernatant liquid. Essentially all the solids, regardless of their fineness, pass into the thickened underflow, and a clear overflow is separated. In classification, on the other hand, the interparti-cle forces are relatively insignificant as compared to the settling force on the individual particles, and are insufficient to prevent independent movement of the particles. The coarsest, heaviest particles settle most rapidly through the pulp, passing more slowly settling fines. Particles coarser than the mesh-of-separation essentially all settle into the underflow, but if the feed contains any particles finer than the mesh of separation, at least part of them will appear in the overflow. A clear supernatant or overflow can be obtained only if there are no undersize particles present in the feed. Thus it will be seen that classification is impossible under ideal thickening conditions. The finer particles are pulled down at essentially the same rate as coarser particles, and there is no separation on the basis of particle size. The surface attraction holding the particles together in a thickener is usually feeble. Whenever the sedimentation force on any particle is strong with respect to the interparticle forces, that particle can pass through the tenuous structure and settle independently. There are at least four ways of making the sedimentation force strong, with respect to the interparticle forces, and obtaining classification. First, and most obvious, the particles may be large and heavy. Thus coarse sands settle out in a beaker or Dorr thickener ahead of the rest of the thickening solids. Second, the interparticle forces may be altered by physicochemical means; i.e., it is often necessary to add dispersing agents to destroy the interparticle forces and permit classification to take place. Third, the interparticle forces may be reduced by dilution of pulp. It is well known that to obtain the most efficient separation of

Jan 1, 1954

By C. W. Thompson

Paul D. Suloff (Goodyear Tire and Rubber Co., Inc., Akron, Ohio)—I would like first to comment on problems of the conveyor belt discussed in Mr. Thompson&apos;s excellent paper, since that is what we hope we know most about. Twists in relatively wide conveyor belt unavoidably produce a lateral maldistribution of tension, raising tension at belt edges and reducing it at the center. They also produce a lateral collapsing force on the belt at the center of the twist owing to the inherent tendency of all the longitudinal elements of the belt to try to pass through a point at the twist center. Calculation of the twist geometry by the methods shown in Mr. Thompson&apos;s paper keeps these extraordinary forces within limits which the belt designer can tolerate. No reduction in belt life due to twisting need be contemplated when this geometry is maintained. There is a minor exception that belts of extreme lateral flexibility will tend to curl laterally at the center of the twist. However, any ordinary fabric construction will perform satisfactorily in this respect. These twists are always made in regions of low tension in the conveyor so that even in the edges of the twist, belt tension does not exceed the average tension found in highly stressed regions of the conveyor. Offsetting these out-of-ordinary belt stresses is the advantage that Mr. Thompson has brought out of getting the return run up out of the dirt where it can be seen. This not only makes it easier to train, but also, in the event that it is not properly trained, frees it of the normal return run edge wear hazard. It is well known that return run edge wear is a prominent cause of belt mortality underground. An interesting aspect of this two-way conveyor is that the belt may be made what is known as a Mobius Strip. A Mobius Strip is obtained by splicing a belt after turning one end of it 180" about its longitudinal axis. In other words, one end is turned upside down before splicing. A belt spliced in this fashion turns itself upside down every time it comes around, but the twist which has been put in the splicing, of course, stays at one location on the conveyor, in this case one of the twist sections at the end. Turning the belt over every revolution might have advantages in some cases. Belts could be made with equal covers and the two sides worn equally and simultaneously. In this case there would be no problem of getting belts on upside down by mistake. However, the two-way conveyor does not have to be a Mobius Strip. It can be twisted in such fashion that the same side is up on both runs. It is simply a question of which way the final 90" twist is made before joining the ends. Another interesting aspect of the two-way conveyor is the problem of operating two-way conveyors in series. Here the sequencing of starting brings up some new problems. It will be recognized, although not always at first glance, that if the starting sequence is planned for one run of the conveyor the reverse will result on the other run. With the two runs carrying bulk material in both directions a reverse sequence on one run would be intolerable. In this situation the only solution appears to be a simultaneous starting of all conveyors in the series. However, with the coal in one direction and intermittent supplies in the other it would be entirely practical to sequence the conveyors for the coal run and accept a reverse sequence on the supply run. The two-way conveyor also lends itself to new driving possibilities. First, it is quite possible to drive at the head end of each run, which of course, means a drive at each end of the two-way conveyor. Driving in this way a given belt can be extended to substantially greater lengths than a conventional conveyor with drive at one end only. In addition to this, under certain conditions the conveyor can be extended to extreme length by driving at one end and at some intermediate point on the most heavily loaded run. As a particular case, a belt carrying coal downgrade and supplies back upgrade could be extended to extreme lengths by driving at the head of the coal run and at an intermediate point of the supply run. Mr. Thompson has been a pioneer in belt conveyor transportation underground and his accomplishment here with the first two-way conveyor of any consequence is another notable addition to the art.

Jan 1, 1954

By H. P. Rassbach, E. R. Saunders

MUCH progress has been made in recent years in the theory and practice of making stainless steel. By effective utilization of oxygen for decar-burization and more suitable alloying agents, it has been possible to attain consistent production of very low-carbon stainless steel. In order to facilitate economical production of stainless steels, the Electro Metallurgical Co. has carried out an extended experimental program that has clarified some of the complex interrelations of temperature and composition under decarburizing and reducing conditions. These results&apos;-:&apos; have been founded in large part on small experimental heats, and in order to confirm their validity and significance under commercial conditions, a survey of stainless steel melting practice has been made with the cooperation of stainless steel producers. Conditions required for decarburization and associated oxidation of chromium, manganese, and iron have been fairly well established in relation to the beneficial effect of the highest practicable temperature. The recovery of chromium and manganese from highly oxidized slags by reduction with silicon has been indicated with somewhat less precision and this study has shown significant deviation in large commercial heats from the small experimental heats. In spite of an unsatisfactory degree of accuracy in estimating the conditions affecting reduction of metallic values, it has been possible to calculate a slag weight in reasonably good agreement with the results observed in large heats. While there still is much to be learned about both the qualitative and quantitative aspects of stainless steel melting, this survey has indicated the manner by which the efficiency of the production process may be measured. Oxidation Period In order to establish practices for the recovery of chromium and manganese from the slag the amounts of these metals oxidized should be known. Moreover, since reduction of oxidized chromium and manganese must necessarily be accompanied by similar reduction of iron, knowledge of the total quantity of metallics oxidized is essential. The relations between carbon, chromium, and temperature under oxidizing conditions were developed by Hilty in 1948.&apos; While it had been realized previously that retention of chromium in the metal during carbon oxidation is favored by high temperatures, the Hilty relation provided quantitative information useful for evaluating melting procedures. For example, it was shown that decarburization to moderate carbon levels can be achieved while retaining substantial amounts of chromium. However, in decarburizing to the low-carbon level necessary for producing 0.03 pct maximum carbon stainless steel, very little chromium remains in the bath at the temperatures generally employed. For this reason, Hilty, Healy, and Crafts&apos; later projected an extension of the chromium-carbon relation to the low-chromium region. Although this chromium-carbon-temperature relation defined the composition of a chromium steel bath at the end of the oxidizing period, it did not provide a direct means for estimating the total amount of metallic oxidation occurring during decarburization of a stainless steel heat. This subject was investigated by Crafts and Rassbach³ and, later, by Hilty, Healy, and Crafts" who demonstrated that metallic oxidation is a function of the chromium content of the initial furnace charge, the minimum carbon content attained, and the temperature. It was further demonstrated from data on 1-ton heats that an empirical relationship exists between the ratio of chromium plus manganese to iron in the slag (S) to the corresponding ratio of these components present in the metal bath. The following expression was derived to permit the calculation of the amount of metallics oxidized during decarburization of a given charge: W-2000 (Cr1 + Mn1)-(Cr2 + Mn2) 1 100s/s+1-(Cr3 + Mn2) where W is the pounds of chromium, manganese, and iron oxidized per ton of charge; Cr1, the percentage of chromium in the charge; Mn1, the percentage of manganese in the charge; Cr2, the percentage of chromium in the bath after oxidation; Mn2, the percentage of manganese in the bath after % Cr + % Mn oxidation; and S =%cr+ % Mn/%Fe in the slag after %Fe oxidation. In order to establish whether the slag ratios of commercial heats are consistent with those found in the experimental heats, the slag and metal analyses shown in Table I were evaluated. These data represent samples taken after the oxidation of two 1-ton and seven 15 to 25-ton heats of types 303, 304, and 304L stainless steel made in chromite, acid, and basic hearths. Fig. 1 illustrates that the results for the commercial heats correlate reasonably well with the relationship originally established for experimental 1-ton heats. It will be noted that in the range of metal composition of these heats, the slag values generally lie above the line. As was suggested by

Jan 1, 1954

By Robert F. Goss

OCAW appreciates the opportunity given to us by the sponsors of this Conference to present our position and policies on the issue of radiation hazards in mining. Our principal concern is the health impact that the mining of uranium has on our members. OCAW represents 1,500 underground uranium miners and more than 10,000 underground miners with 3,000 in the Rocky Mountain region. The U.S. Public Health Service has determined through mortality studies that the number one cause of death among uranium miners is lung cancer. It was also determined that exposure to radon daughters and mine dust correlates with the lung cancer experience of uranium miners. Data from the U.S. Mine Safety and Health Administration has also shown that not only uranium underground miners, but all underground miners, are exposed to radon daughters -- especially underground miners in the Rocky Mountain region. It is our position that any OCAW underground miner is at potential lung cancer risk. The dosages of radon daughters that our miners are exposed to are very many times the background levels of radon exposures in the communities where they live. We are also aware that cigarette smoking accelerates the onset of lung cancer; however, it has to be clear that the available scientific evidence shows that alpha radiation does initiate lung cancer and that cigarette smoke, as a recognized co-carcinogen, promotes cancer already initiated by radiation. It is true that cigarette smoke increases the risk of cancer significantly for miners exposed to radon, but nonsmoking miners have experienced lung cancer rates twice as high as the comparable members of the U.S. population. OCAW&apos;s position is that the occupational regulatory agencies should concentrate on the exposures that can be controlled; that is, occupational exposures rather than life-style exposures. Our Union has maintained a consistent posture in relation to carcinogens in the workplace -- that is, exposure to cancer-causing agents should be limited to the [lowest feasible level]. OCAW has interpreted lowest feasible level as the lower limit of detection of the collection and analytical method used to detect the carcinogen. Our posture is based on the available scientific information on carcinogenesis. We have asked the scientific community, many times, to provide us with safe levels of exposure to carcinogenic substances, including radon daughters. The answer has been: "We cannot determine levels of exposure low enough to assure that no cancer will occur." In short, there is not a "safe threshold" for any carcinogen. This statement does not come from one of the few so-called "pro-labor scientists," it comes from the National Cancer Institute and the National Institute for Occupational Safety and Health. I don&apos;t need to be a scientific sage, then, to conclude that the lowest level of exposure corresponds to the lowest risk of developing cancer. That is, then, our policy on exposure to carcinogens. It seems there has been an attempt to ignore the fact that lung cancer in uranium miners is the principal cause of death. Uranium miners are no exception from workers exposed to carcinogens. Our policy applies to them. Uranium miners should be exposed to the lowest feasible level of radon daughters and any decrease in the permissible exposure level is a decrease in their lung cancer risk. Accordingly, OCAW has petitioned the Department of Labor for a new permissible exposure limit to radon daughters in uranium mining, which lowers the current exposure standard from 4 Working Level Months (WLM) per year to 0.7 Working Level Months per year. We made our demand to the Department of Labor on April 20, 1980. We are still awaiting action from the Federal Government on our petition. OCAW is also very concerned with other important health impacts of uranium mining. We are concerned with a rate of disabling accidents and fatalities which is twice as high as the same rate in other underground mines, excluding coal. We are also concerned with the rate of respiratory disease fatalities among uranium miners which is almost four times the rate among a comparable U.S. population. We have expressed those concerns when the U.S. Senate proposed a Federal Compensation Act for uranium miners. That proposal, by Senator Dominici of New Mexico, found a quiet death in two Congressional sessions. In conclusion, our position on lung cancer induced by radon daughters is the same position we have taken with all other industrial carcinogens: The lower the exposure, the lower the risk. OCAW is demanding a drastic decrease of the permissible exposure limits. OCAW will never accept that a segment of our membership which mines uranium should take the lion&apos;s share of the risk while the uranium mining companies take all the benefits.

Jan 1, 1981

The pressure of the gas in equilibrium with sphalerite has been determined in the temperature range of 680&apos; to 825°C, using the Knudsen orifice method. A comparison of these experimental pressures with those calculated from thermal data and from other equilibrium measurements shows that the vapor above sphalerite is predominantly dissociated ZnS. Equations have been given for correctly calculating dissociation pressures using the Knudsen orifice method. It has been shown that the experimentally determined pressure is the same, whether the zinc sulphide is sphalerite or not, or a mixture of wurtzite and sphalerite. CONFLICTING points of view appear in the literature on the constitution of the vapor in equilibrium with solid zinc sulphide in the vicinity of 800°C. By comparing the dissociation pressure calculated from thermodynamic data and the vapor-pressure determination of ZnS by Veselovski,1 Lumsden2 has concluded that the vapor consists largely of dissociated ZnS. Sen Gupta,&apos; however, concludes from his spectroscopic determinations that the vapor is largely ZnS molecules. In view of the fact that the thermodynamically calculated&apos; dissociation pressure is higher than that experimentally measured by Veselovski, it seemed in order to repeat Veselovski&apos;s measurements. Experimental Procedure The method used for the determination of the pressures in this papel- is the Knudsen effusion cell. The apparatus and procedure were described in a previous paper- from this laboratory on the determination of the vapor pressure of silver. The only difference is that the Knudsen cell in this work is made from platinum and there is no external cover around the cell. The cell is an ordinary platinum crucible of 2.2 cm top diameter with a capsule cover. It was thought that platinum might stand up at these temperatures to the solid and gaseous ZnS, since it was found that the weight of the platinum cell itself did not change appreciably on heating ZnS in it at the working temperatures. To insure that reaction of the zinc sulphide with the cell was not giving&apos; a false value, a stabilized zirconia cell was employed for check runs. Fig. 1 shows the comparison, which is satisfactory. Veselovski previously had measured the vapor pressure of ZnS using a silica Knudsen effusion cell. On repeating his experiment in this laboratory, it was found that ZnS at-tacked the silica cell, giving it a marked frosty appearance. This led to the belief that Veselovski&apos;s result:; may be in error. Also, he was operating at pressures above the range ordinarily considered safe for the Knudsen method. The effusion rate was measured by weighing the cell before and after each run. The weight loss during heating to temperature and cooling down was measured and subtracted from the weight loss during the actual run. The zinc sulphide used in this investigation was from two sources: Fisher cp grade, and a sample of pure sphalerite supplied by Mr. E. A. Anderson of the New Jersey Zinc Co. Before and after the series of runs with Fisher ZnS, X-ray analysis showed that both wurtzite and sphalerite were present. However, the ratio of sphalerite to wurtzite increased. All measurements were made below the transition temperature which has been reported" to be 1020°C. The data obtained in this investigation are tabulated in Table I. The pressure was calculated by the usual Knudsen formula" on the assumption that ZnS molecules were effusing. From these data, using pure sphalerite in the platinum Knudsen cell, the vapor pressure of ZnS, in mm of Hg, as a function of temperature is given by the solid line in Fig. 1. The best straight line, as determined by the method of least squares, is given by 14405 logpzns =-14405/T +11.032. A comparison of these results with Veselovski&apos;s shows that his results are about 50 pct lower. Discussion The vapor in equilibrium with solid zinc sulphide in the temperature range of this study will consist of Zn, S2, and ZnS mol, since other species of zinc and sulphur&apos; are relatively unstable. The question to be settled is whether or not ZnS is largely dissociated. The derivation8 which follows gives the method of calculating the pressure of zinc and sulphur over solid ZnS, assuming complete dissociation, from Knudsen cell data. The free energy of the reaction 2 ZnS(solid) ? 2 Zn(gas) + S2(gas) is given by ?F?° = -RT In K = —RT In p12p2 where p1 is the zinc pressure and p is the sulphur pressure. If dissociation occurs in a closed system,

Jan 1, 1955

COUNCIL AND STANDING COMMITTEES - 1973-1974 Office Bearers: P. W. J. van Rensburg (President), Professor R. P. Plewman and Dr R. E. Robinson (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and Dr J. P. Hugo (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, G. H. Grange, Dr P. R. Jochens, J. G. Kirchner, Dr D. I. Legge, W. W. Malan, Dr M. D. G. Salamon, L. W. P. van den Bosch, D. A. Viljoen, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), E. T. Wilson (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, Professor J. de V. Lambrechts, R. C. J. Goode, Professor D. D. Howat, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing committees held 30 meetings. COMMITTEE CHAIRMEN Membership, Dr R. E. Robinson ; Metallurgical Colloquia, Dr R. E. Robinson ; Mining Colloquia, L. W. P. van den Bosch; Awards, P. W. J. van Rensburg; Excursions, P. A. von Wielligh; Dinner, G. H. Grange ; Constitution, Rules and Policy, Dr J. P. Hugo; Adjudicating, P. W. J. van Rensburg; Mines and Works, W. W. Malan; Education, Dr J. P. Hugo. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies: Members : V. C. Robinson and D. G. Maxwell Alternates : P. W. J. van Rensburg and Dr J. P. Hugo. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg Alternates : Dr J. P. Hugo and G. H. Grange. South African Council for Professional Engineers Members : R. C. J. Goode and J. K. E. Douglas Alternates: G. H. Grange and Dr R. E. Robinson. Engineers&apos; Liaison Committee (Pretoria): Member: Professor J. de V. Lambrechts Alternate : Dr J. P. Hugo. MEMBERSHIP Seventeen Fellows and Members, twenty-three Graduates, ten Associate Members, twenty-two Associates, thirty-four Students, and seven Company Affiliates were elected during the year. Eleven Fellows and four Members were admitted to retired membership. Five Fellows were elected to Honorary Life Membership. Four Members, two Graduates, and one Student were transferred to Fellows ; eleven Graduates and Students were transferred to Members ; eight Students to Graduates; and four Students to Associates. A statement of membership as at June 30th 1974 and the end of the previous year is given in the following tabulation 30th - 30th June, - June, 1973 - 1974 Honorary Life Fellows 4 - 9 Honorary Fellows 9 - 8 Life Fellows 177 - 170 Fellows 536 - 544 Members 487 - 512 Associate Members - - 10 Graduates 128 - 130 Associates 186 - 194 Students 183 - 173 Company Affiliates 64 - 70 1 774 - 1 820 OBITUARIES Your Council records with deep regret the death during the year of the following members : Dr P. N. Lategan and Dr O. A. Jackson, Honorary Life Fellows and Past Presidents; C. Airth, T. L. Blunt, J. B. Dennison, A. E. Frazer, C. L. Lamb, V. O. Reid, K. Richardson and D. G. Roberts, Life Fellows ; H. F. Allan, J. T. Beaumont, M. Eisenstein, J. C. Hall, C. F. Louw, H. H. McGregor, R. Murchison, and J. E. Williamson, Fellows; and R. B. Miles, Associate. FINANCE The annual accounts, which follow this report, reflect a healthy position and show that measures taken by Council over the last few years to boost income have been successful. A higher income was needed not only to meet rising costs but also so that the services provided by the Institute for its members could be expanded. This year&apos;s income of R55 025 showed a further increase compared with last year&apos;s figure of R48 307. Income from subscriptions was higher mainly owing to an increased number of Company Affiliates, and this is indicative of the support given by mining and metallurgical companies to the good work being done by the Institute. Further sales of publications of the symposia held over the last few years again made a useful contribution to income of R4560. The first Winter School held in 1973 yielded a surplus of R7495 after the expenses had been deducted from the income received from registration fees. The cost of administering the Institute increased by R2212 compared with the previous year. Included in this was a donation of R1000 to the A.S. & T.S. Trust Fund. The cost of publishing and printing the Journal increased by R2034, but advertising and extraneous sales of the Journal were higher, with the result that the net cost of the

Jan 10, 1974