Search Documents

By A. O. P. Casbarian

An analytical method is developed to determine the variation of the ultimate lateral resistance of a plate in a cohesionless soil with depth. This analysis is based on a modification of Rankine's classical earth pressure theory and the theory of plasticity as applied to soils. The ultimate resistance is defined as the product of the effective stress at the midpoint of the plate, the area of the plate and a dimensionless variable termed the ultimate resistance factor. This variable has been plotted us the depth ratio: i.e., the ratio of of the depth of embedment us the height of the plate. The resistance of a plate may then be calculated using the values af the ultimate resistance factor from the chart provided or the equation may be programmed for use in an analysis of anchor systems in cohesionless soils. It is emphasized that the analysis is semitheoretical. The theory has been compared with experimental results reported in the literature and results indicate general agreement. Actual field tests are necessary to further verify this theory. INTRODUCTION With the exploration for oil offshore in waters all over the world, it is of importance to determine the behavior of the various soils in relation to their ultimate resistance to deformation. Examples of such problems are the holding capacity of anchors and the lateral resistance of piles. Very little information is available in the published literature on the design and performance of anchors, in either cohesive or cohesionless soils. The analysis developed in this report is the first step in obtaining a solution for the determination of anchor holding capacity in a cohesionless material. DISCUSSION The theory used in the analysis is based on the ultimate strength of the soil and is the maximum resistance developed by the plate against further movement. In such a state the elastic deformations are disregarded in comparison with the plastic deformations. Hence, the plate can be considered as completely rigid. The theory of plasticity determines the three unknown stresses at any point by means of two equilibrium conditions for a small earth element in combination with the failure condition. However, the exact solutions can only be carried out in a few simple cases such as, for example, when the rupture or failure lines are straight (Rankine theory) or with spiral and straight rupture lines (Prandtl theory).l Kiitter 2 derived a single equation expressing the variation of the stress in any given rupture line. To utilize this equation, it is necessary to know the stress in the rupture line at a certain point. Unfortunately, this is difficult to obtain unless the rupture line intersects the free surface at a certain angle or when the earth is cohesion-less and unloaded. A method to overcome this is to consider only the boundary conditions at both ends of a rupture line without investigating the equilibrium of the earth above the rupture line. This assumes that the rupture lines meet the surface at statically correct angles, so that boundary stresses may be determined. As Kiitter's equation furnished a relation between these stresses, the unit earth pressure may be calculated at the point where the rupture line meets the wall. Another way in which Kotter's equation may be applied is in investigating the equilibrium of a soil mass above a rupture line. This method assumes that the failure or rupture line is known and that the boundary stresses in the rupture line at the ground surface can be determined. In this case it is possible to determine the earth pressure from the equations of equilibrium.

Jan 1, 1967

By W. T. Cardwell

Physically absurd, triple-valued saturations appear in the straight-forward solution of the Buckley-Leverell equations for the displacement of oil by water or gas. From an engineering viewpoint, the triple value causen no difficulty. It is well known how it may be compensnted in order to obtain physically meaningful, numerical results. From a scientific viewpoint, the question still arises: What did the triple value mean? This paper explains how and why the triple value arose in non-capillary Buckley-Leverett theory. The discussion should serve as a background for the understanding and use of the modern method of characteristics in di.~pkzc(>ment theory. INTRODUCTION Displacement theory was introduced to petroleum technologists in 1 941 by Buckley and Leverett.' Their first equation, which they wrote down without derivation, was equivalent to the following: ?s/?t= - qr/F ?f/?r (1) where S = saturation of displacing fluid (a fraction) r = time q,. = total volumetric velocity of both the displacing phase and the phase being displaced (usually, but not necessarily, assumed to be a constant) F = porosity (a fraction) f - fraction of the total volumetric velocity that is the volumetric velocity of the displacing phase (assumed to he a function of S only x = distance. Buckley and Leverett called Eq. I "a material balance equation". Actually it is derived from both a continuity equation, or material balance equation, and Darcy's law. Buckley and Leverett jumped from their Eq. 1 immediately to their Eq. 2, which was the equivalent of the following: (?x/?t)x = qr/F df/ds = qr/F f'(s) (2) The jump from Eq. 1 to Eq. 2 involves apparently simple mathematics, but in that apparently simple mathematics lies a subtle point that is part of the key to the meaning of the triple value to be discussed here. Eq. 2 may be readily interpreted as saying that a point of constant saturation (on a saturation-vs-dis-tance curve) moves with a constant velocity that is proportional to the total volumetric rate, inversely proportional to the porosity, and is otherwise a function of the saturation itself. So that if one knows the derivativc with respect to saturation of the fractional flow function, f(S), for each saturation, one knows the velocity of each point of the moving saturation-vs-distance curve. The function f(S) can he determined experimentally and its derivative f'(S) can be calculated. It turns out that the experimentally derived f'(S) is not a monotonic function of S, but instead it has a definite maximum and declines away at both high and low saturations. This in turn means, in accordance with Eq. 2, that on a moving saturation-vs-distance curve, ccrtain intermediate saturations will travel faster than the saturations either higher or lower. The result is indicated in Fig. 1. In Fig. 1, the abscissas represent distances along a column of porous medium, which column is assumed to be uniform in cross-section perpendicular to the ab-scissal direction. The ordinates represent fractions of pore space occupied by the displacing phase, which may be either water or gas. It is assumed that the saturation is uniform over all planes perpendicular to the abscissal direction. The saturation is a function only of time and one space variable. Time variation of the saturation is represented by change in shape of a curve such as curve AGJ, which represents the initial saturation-vs-

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.' Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"INTRODUCTION The design, development, fabrication, and test of cryogenic breathing apparatus is part of a much larger effort funded by the National Institute for Occupational Safety and Health (NIOSH) and managed through a Space Act Agreement with the National Aeronautics and Space Administration (NASA) at the Kennedy Space Center (KSC) in Florida. This effort is designed to create cryogenically based life support equipment that is responsive to the needs of miners as required by the Miner Act of 2006. Our goal was to design and build a liquid air based self-contained breathing apparatus (SCBA) that lasted 2 hours and would be used for the egress of miners during a mining accident and be refillable while worn. Therefore, the current report describes tests of an Advanced Cryogenic Breathing Apparatus (termed the ACryoBA) designed to provide miners egressing an emergency situation with a two-hour open-circuit SCBA. The ACryoBA utilizes low pressure cryogenic liquid air instead of high pressure compressed air commonly used in most commercially available SCBA. The ACryoBA can also be self-filled from strategically placed Cryogenic Air Supply and Fill Stations (CryoASFS) initially, and thereafter on the egress route approximately every 1 hour and 30 minutes with a 30 minute air reserve. The ACryoBA evolved originally from a one hour Liquid Air Pack (LAP) developed in the 1980’s for Space Shuttle Rescue forces allowing for longer duration and cool air (Figure 1). It was used successfully for many years, through the end of the Space Shuttle Program. The first attempt at a mine egress pack was the Cryogenic Breathing Apparatus (Figure 2). It was to have a low profile, two hours of breathing, attitude independence, and a simple rapid refill while in use. The CryoBA met the two hour criteria, but with difficulty due to excessive heat leakage caused by the dual 4 liter Dewar design. Much of the stored air was lost as it vaporized faster than it could be used. However, the pack was successful in demonstrating both attitude independence and a simple rapid refill capability. The ACryoBA project was designed to continue the progression and address the deficiencies in the CryoBA. The ACryoBA pack was designed to last 2 hours. It minimizes the heat leakage with a single Dewar and thereby requires less liquid air. The single Dewar design also minimizes weight, making it much more manageable by the user (Figure 3). The ACryoBA complies with 42 CFR part 84 NIOSH certification test requirements. One critical requirement for the ACryoBA is operation in positions other than vertical for periods up to 1/4 (i.e. 30 minutes) of the rated service life of 2 hours; this was accomplished by use of new technology called the “attitude independent pickup” which is abbreviated “AIP.” The AIP, developed by BCS Life Support LLC (patent #8,899,226), has a tube going from the top flange down through the center of the Dewar. At the end it has a flexible bellows and a weighted end. Due to the flexible nature of the bellows, the pickup at the end is free to rotate and follow the liquid level around within +/- 90o of vertical."

Jan 1, 2016

By J. C. Rengel

Why and how the nuclear industry entered the electric power generation business is discussed in terms that nuclear energy was an undoubtedly additional energy resource and that it had promise of becoming a virtually inexhaustible generating power if breeder reactors could be devised. The growth of nuclear power, its total generation capacity, are related to the need of increasing energy requirements. The use of atomic energy for power generation will grow if it can compete economically with other fuels. The rate of growth, the time scale and direction of technical development is dependent on ore supplies. It is predicted that by 1980, 50% of all new power installations will be nuclear stations. INTRODUCTION Ten years ago, the nuclear industry was virtually unborn, the Atomic Energy Act of 1954 had just been signed, and peaceful applications of atomic power was little more than a phrase. Serious discussion of the practical application of nuclear energy to electric utility installations in the West was highly unlikely. The questions: Why and how did the nuclear industry enter the electric power generation business at all?; What is the predicted growth of nuclear power?; What technological changes do we predict?; How will the above changes affect the utilities? will in part be answered by this paper. WHY NUCLEAR POWER? The only justification for the West as for any other section of the country for atomic power is economics. Whatever energy source will provide the lowest generation cost will prevail; the only electric utilities which have shown an interest in nuclear power are those to whom it means lower generation costs. It is true that the Government sponsored the development of this technology long before there was any evidence of better economics; but a Government must take a very long-range view and it is the only type of organization that can afford to look more than twenty or thirty years into the future. The Government looked at projections such as shown in Fig. 1, which shows various rates of energy consumption, and matched these against estimates of fossil fuel resources. This showed that we will exhaust our low-cost fossil fuel supplies within 75 to 100 years and our total known fuel supplies within 150 to 200 years. The decision to invest in nuclear energy rested, therefore, on two arguments: a) It was undoubtedly an additional energy resource; and b) It has promise of becoming a virtually inex-haustable resource if breeder reactors could be devised if, while generating power, the reactors would produce more fissile materials than they consumed. This decision produced an unexpected bonus: nuclear power became competitive with fossil power much earlier than had been expected and, as shown in Fig. 2, forced the coal industry to take a hard look at its own position. I believe that the drop of coal prices shown here is the direct result of the entry of nuclear power into the energy supply business. At this point, it ought to be explained why and under what conditions nuclear power can be cheaper than fossil power. Fossil fuel cost to the utility is composed of two factors: a) Mining; and b) Transportation. As a result, the cost of fossil fuel to the utilities varies from 126, 106 Btu to 306, 106 Btu and higher. Nuclear energy is highly concentrated and the transportation factor becomes insignificant. Today the cost of nuclear fuel to the utility ranges between 156

Jan 1, 1967

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By C. J. Ramsburg

THE construction and operation of by-product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. CARBONIZATION PROCESS Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 950°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe. This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about I 7 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over 2000°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 1/2 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,' Zr-Si,' and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies' and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.' Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,' was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By R. J. Schaefer, M. E. Glicksman

Direct, in situ observation of metallic alloys during solidification reveals that in some systems crystal multiplication occurs by means of a dendrite remelt-ing process, without the necessity of independent nu-cleation events. The solidification is observed on optically clean surfaces of supercooled molten alloys. In one system (Sn-3 wt pct Bi) , a fine-grained equi-axed structure is produced by the complete disintegration, via remelting, of transient initial dendrites. In contrast, several other metallic systems show little or no evidence of remelting activity. The behavior of these metallic systems is consistent with that expected on the basis of published observations of dendrite remelting in transparent organic alloy systems. It is concluded that dendrite remelting is an important crystal multiplication process in some metallic alloys, but is velatively unimportant in some other alloys. The detachment of dendrite branches from the primary stem by a remelting process has been observed by Jackson, Hunt, Uhlmann, and seward1 during the solidification of some transparent organic alloy systems. The branches released by this remelting process can drift free of the primary stem and serve as seeds for the formation of numerous independent crystals. This proliferation of new crystals does not require repeated independent nucleation events, but only modification of the initial solidification structure. The mechanism of dendrite remelting, as described by Jackson et a1.1 and by Tiller and O''Hara,2 is dependent on the transport of both heat and solute and is, therefore, expected to operate only in alloys, and not in pure substances. It was found in the transparent organic alloy systems that remelting occurred primarily in the constricted regions near the base of dendrite branches, where the branches had grown through the solute-rich liquid layer surrounding the primary dendrite stem. It was suggested that impure solid had formed in these constricted regions at a relatively low temperature and had later become unstable as further solidification of purer material raised the temperature. Jackson et al. proposed that the equiaxed zone of metal alloy castings originates from a similar remelting process, and they demonstrated the operation of this mechanism in "ingots" poured from saturated salt solutions. Although these substances were especially selected to show solidification behavior similar to that of metals,3 the remelting mechanism has, until now, been subject to the objection that its operation has not been directly observed in a metallic system. Considering the fact that thermal properties such as diffusivity may differ by as much as two or three orders of magnitude between metals and organic compounds, this objection was considered to be possibly serious. A method has now been developed by which it is possible to make direct optical observations of metals during solidification. This method has revealed transient solidification processes which would not be detected by metallographic examination of totally solidified specimens. In particular, a grain-refinement process in a metallic alloy has been observed to be a direct consequence of the total disintegration of an initial dendritic structure. The influence of an initial, transient solidification structure on the final solidification structure is demonstrated here for the first time in a metallic system. I) EXPERIMENTAL The technique of using a transparent flux to maintain an optically clean metal surface during solidification has been described by us elsewhere.* The

Jan 1, 1968

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

By S. A. Spachner

An analysis of the powder patterns of the omega transition phase in three binary titanium alloys containing 8 pct Cr, 13 pet Mo, and 15 pet V, respectively, showed that all could be indexed on an orthorhombic unit cell. The unit-cell dimensions were all quite similar. There is evidence for the occurrence of more than one transition phase in Ti-Cr and Ti-V alloys. FOLLOWING the discovery of a new brittle phase in certain titanium-chromium alloys by Frost, Parris, Hirsch, Doig, and Schwartz,' named ? by these investigators, much interest has developed concerning the identification of alloy systems in which this phase exists, kinetics of the transformation in such systems, and the crystal structure of the ? phases appearing. Omega has been found in alloys of titanium-manganese, titanium-molybdenum, titanium-iron,' and titanium-vanadium.' In the present work, a study was made of the powder patterns of the ? phase occurring in alloys of Ti-8Cr, Ti-13Mo and Ti-15V in an effort to obtain a basis of comparison for ? phases appearing in these different alloys. Comparison of Alloys for ?-Phases Two hundred mesh powders of Ti-8Cr, Ti-13Mo and Ti-15V were prepared. A portion of powder sufficient for three x-ray powder specimens was placed in a Vycor tube, evacuated to less than 0.1 µ pressure, filled with argon, and sealed. The tubes were then heated to 900°C, held at this temperature for 30 min, and water-quenched. Following this transformation to the ß phase, the specimens were quenched in lead or solder pots, held at the desired temperature for varying lengths of time and water-quenched. The heat-treatments used and the phases identified are listed in Table I. The intermediate water quench was used in lieu of direct downquenching from 900°C to the bath temperature desired to circumvent the possibility of transformation of the powder specimen from ß to (ß + a) while it was being moved from the homog-enization furnace to the lead bath. To check the possibility that upquenching to the bath temperature might bring into play a different mechanism than downquenching to this temperature, resistivity measurements were compared on Ti-8Cr rod specimens which were transformed isothermally at 400°C by downquenching from the solution-treatment temperature and those which were transformed at 400" C by upquenching ß specimens from room temperature. The results are shown in Fig. 1. No difference in transformation mechanism was noted. It soon became apparent that sufficiently detailed Debye-Scherrer photograms of the ? phase in the alloys which were to be used could not be obtained by the use of copper radiation. Although satisfactory photograms of ß and ß + a phases were obtained with this radiation, the ? phase appeared to exhibit mild fluorescence, making interplanar spacing computation virtually impossible. Molybdenum radiation appeared to offer promise in cutting down this fluorescent effect, the mass absorption of titanium for molybdenum radiation being 23.7 in contrast to 204 for copper radiation. The reduction in the accuracy in determining the location of the photo-gram lines caused by the shorter wave length of molybdenum characteristic radiation did not appear to be a significant factor. Utilizing a camera of 57.3 mm radius, best results were obtained for exposure times ranging between 30 and 40 hr. Tube potential

Jan 1, 1959

By I. Tamura, J. O. Brittain, T. Mura

Plain carbon steel in the cold worked or marten-sitic conditions has an internal friction peak at about 250 oC at a frequency of I cps. The influence of substitutional alloying elements on this peak was examined experimentally. The alloys were vacuum melted Co-, Cr-, Mo-, Ni-, and Si-iron (about 3 pct alloying elements), and carburized Si-iron. The internal friction of the alloys in the temperature range 30o to 500 OC was determined by means of a torsion pendulum. The 250 oC peak of the cold-worked alloys was lower in height than that observed in plain C-iron and steel. Carburized Si-iron in the quenched condition had a peak which occurred at a slightly lower temperature than in quenched plain C-steel, but the height of the peak was substantially greater than that found for the same alloy in the cold-worked condition. The activation energy of this peak for martensitic Si-steel was about 35 kcal per mol. ANNEALED a iron has two internal friction peaks due to nitrogen and carbon at 20o and 40o C respectively, at a frequency of 1 cps. If a iron is cold worked, these diffusion peaks become smaller and a new peak appears at about 250o C. The activation energy for the 250o C peak is in the range of 32 to 44 kcal per mol and has an average value of 38 kcal per mo1. It has been experimentally verified that both interstitial solute atoms and dislocations are necessary for the 250o C peak. 3 Wert has also shown that an incubation period precedes the appearance of the 250 C peak.4 With regard to quenched martensitic steel, Ke et al.596 observed two peaks at around 130o and 250o C. They conjectured that the 250o C peak in martensite was due to the same mechanism as the 250°C peak in cold worked a iron, and the 130°C peak was due to the nature of tempered martensite. They did not report the activation energy for these peaks. Chernikova7 found only one peak at about 200° C in tempered martensite. In a previous paperS we reported an activation energy of approximately 40 kcal per mol for the 250° C peak in plain carbon martensitic steels. Ichiyama8 found the activation energy to be about 36 kcal per mol for the 250° C internal friction peak in steels in the martensitic condition. The present authors proposed a theory for the 250°C peak for cold worked and quenched iron and steel.= The theory for the peak is based upon the addition of a strain-energy term to the free energy for the formation of a carbide precipitate due to the presence of a disclocation. The model employed for the relaxation process consists of the growth and solution of a carbide precipitate of critical size as a consequence of an oscillating dislocation. In this report, the influence of substitutional alloy ing elements on the 250° C peak is examined and the experimental results are discussed in terms of our theory for the peak. Most of the experimental work on the alloy steels was confined to the Fe-Si-C alloys.

Jan 1, 1962

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By John R. Caldon

INTRODUCTION Leasing has become a major industry in many countries because of the advantages it affords. Whilst the accounting, legal and tax treatment of leasing varies from country to country, there is far more similarity than difference. The general approach to the subject is largely the same. This paper looks to the basic financial considerations in the decision to lease or buy. TYPES OF LEASES Before embarking upon the subject, it would seem appropriate to define a "lease". A lease may be defined as: "an agreement granting one party the right to use, for a specified period of time, property owned by another party in return for a series of payments of rental by the user to the owner''. Ownership, of course, generally entitles the owner to unrestricted use of the asset over its useful life in contrast to a lease which gives the lessee use over a limited period. The distinction between the status of owner and a lessee often is fairly small. In this case we are dealing with what is generally termed a "finance lease". A finance lease is one which substantially transfers the risks and benefits of ownership from the legal owner to the lessee. For example, a finance lease would exist where the lessee enters into a lease of an asset for most of its useful life and has an option to buy the asset at the end of the lease for a price which takes cognisance of the rentals already paid. Where a lease does not substantially transfer the benefits and risks of ownership to the lessee, i.e. those benefits and risks remain with the owner and lessor, the lease is termed an "operating lease" and is an agreement for the renting and usage by the lessee of an asset owned by the lessor for a limited period. An example of an operating lease might be where a tenant leases a building for a defined period say 6 years with the rent and occupancy subject to renegotiation at the end of the lease term. The economic consequences of the distinction between a finance and an operating lease is very important. With a finance lease, the lessee has a de facto economic interest in the asset and the alternative to a finance lease is some form of purchase; with an operating lease, the lessee does not have a basic economic interest in the asset and consequently a comparison with a purchase option involves far more than simply a funding comparison. Some of the principal differences between finance and operating leases can be summarised as follows: (a) finance leases: -the risks and benefits of ownership are substantially transferred to the lessee; -the lessor normally recovers his investment during the term of the lease; -the lessor in entering into the transaction is relying more on the creditworthiness of the lessee than the underlying value of the asset; - the lease is either non-cancellable or a large penalty will apply for unilateral cancellation by the lessee; (b) operating leases -the risks and benefits of ownership remain essentially with the lessor; -the lease rental income would not normally cover the recovery of the lessor's investment; -the lessor evaluates his risk in terms of the underlying value of the assets;

Jan 1, 1985

By A. R. Gregory, M. R. J. Wyllie

The literature reveals that scant attention has been paid to the systematic experimental determination of the formation factors of unconsolidated porous media. No experiments appear to have been made on the effect of increasing cementation on the formation factor of an initially unconsolidated porous medium. Measurements have accordingly been made of formation factors as a function of porosity for aggregates of spheres in the porobity range 12-56 per cent and of cubes, cylinders, discs and triangular prisms in the porosity range 30-45 per cent. The results are examined in the light of the theoretical equations of Clerk Maxwell. Fricke and Slawinski. Aggregates of unconsolidated spheres and beach sands have been artificially cemented with silica and the formation factor-porosity relationships determined. A theory is outlined which seeks to explain the results obtained and which postulates that formation factor and porosity data for consolidated sandatones may be used to determine the original porosity of the unconsolidated sands from which the consolidated sandstones were derived. It follows also that for consolidated sandstones F' = C where F is formation factor, fractional porosity and C and k are constants. INTRODUCTION All schemes of electric log interpretation implicitly or explicitly require the use of formation resistivity factors or? as they are now generally called. formation factors. 'The originator both of the concept of formation factor and of the use of formation factor data in electric log interpretation was Archie.' More recently it has been suggested that formation factors are of value in describing fluid flow in porous media. A full discussion of this problem together with adequate reference.: has been given by Wyllie and Spangler.' In spite of the theoretical and practical importance of the subject, there appear to be remarkably few basic formation factor data in the petroleum literature. A wider search reveals that this situation is nut confined to the literature of the to industry. at various times over the last century, attempts have been made to compute the theoretical relationship between the formation factor and porosity of simple systems of unconsolidated particle.. However. the formulae derived are not all identical and the experimental evidence adduced in support of each i; not wholly convincitng. Most of the experimental work has been carried out on system. of unconsolidated spheres, although some attention has been given to systems of spheroids and cylinder. Other simple shapes have received neither theoretical nor experimental investigation. The writers feel that a better understanding of the formation factors of complex systems of practical importance requires a firm foundation of reliable experimental data applicable to simple systems. Accordingly, they have reviewed the relevant literature and have determined experimentally the relationship between the formation factor and porosity of unconsolidated aggregates of particles of regular geometrical shapes. Some experiments have also been carried out to investigate the effect of cementation on the formation factor-porosity relationship. PREVIOUS WORK Although the term formation factor was not used. the relationship between the resistivity of a solution containing dielectric solids and the resistivity of a similar solution not containing solids is an old and important problem. The formation factor of a system of dispersed spheres as a function of porosity was considered by Clerk Maxwell. Maxwell arrived theoretically at the following expression: where F is formation factor and fractional porosity. Lord Rayleigh' also examined the problem of the formation factor of systems of spheres and cylinders and concluded that for spheres Clerk Maxwell'.; expression gave a value of F whirl]. at low porosities particularly, was too small. However,

Jan 1, 1953

By T. E. Schmieman, J. E. Miller, M. L. Rizzone

Both centrifugal and reciprocating-type pumps have been widely used in the transport of slurries. Although with some limitations, centrifugal pumps may be used, especially for short-haul systems, however, for the long pipelines the reciprocating pumps are better suited. A state-of-the-art review is presented in which a discussion of applications is made and some of the problems associated with meeting the proper design conditions for satisfactory service are discussed. Several developments underway give considerable promise of better pumps in the future, although the current level of development provides for an economical means to move slurries. The movement of liquids in pipelines necessarily occasions the use of pumps. The petroleum industry is familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well, the circulating fluid utilized to remove drill cuttings is called drilling mud. This substance is usually a fairly sophisticated material designed to develop certain characteristics desirable in the drilling process. The cuttings are suspended in a moving column of this fluid and brought to the surface. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits; however, it is impractical to remove the cuttings completely and as a result they are pumped through the mud pumps back into the circulating stream. Over the years, mud pumps have been improved so that rather long life can be obtained from liquid end parts subject to the attritional effects of the abrasive-laden fluid. It is from this background that reciprocating-type slurry pumps have been developed. Centrifugal Pumps Centrifugal pumps have also been used to transport solids, where low heads are required, typically up to 200 ft or so, and for short hauls. The centrifugal pump is a hydrokinetic device wherein the increase in velocity of a fluid stream is converted to head, and to achieve high heads a large change in velocity is necessary. Abrasive laden fluids cause wear on impellers and casings as a result of erosion by the fluid and the suspended particles. Centrifugal pumps, therefore, can only be used where the internal velocity of flow is rela- tively low. The advantage of centrifugal pumps is their high capacity at relatively low capital cost and usually relatively small space requirement. One of the disadvantages of the centrifugal pump when used in slurry pipelining can be seen in its typical pressure-volume performance relationship, which tends to work against the application (see Fig. I). If an increase in pressure (head) is occasioned by flow restrictions in the pipeline, say by the dropping out of solids, a desirable characteristic of a slurry pump would be that it develop increased pressure to overcome the restriction. The centrifugal pump provides the increased pressure only at the expense of considerably reduced volume which then results in a lower flow velocity. With the reduced flow rate, adequate velocity to hold the material in suspension and keep it flowing in the line might not be achieved. If centrifugal pumps are considerd for the movement of solids in a long line, a series of pumps must be staged in order to provide the necessary motivating force. A large number of pumps in the line would be required, since each of the pumps could provide only a small pressure increment. An equal number of standby pumps

Jan 1, 1971

By M. Mills, M. W. Clegg

This Paper Presents an approximate analytical solution to the problem of the pressure distributions arising from the production of a compressible liquid in a partially penetrating well. The limits of validity of the approximation are discussed and it is shown that the basic approximation is the same as that used in previous numerical of the problem. The variation in pressure at the production well with time for different penetration ratios is investigated and is shown to agree with previous work. The solutiOns are used to assess the effects of partial penetration at large distances from the well and at the wellbore itself. In the latter case the effects of anisotropy are also studied for constant, but unequal, horizontal and vertical permeabilities. It is 'uggested that measurements of the Pressure drawdown below the producing interval in a well should give some indication of a thickness-vertical permeability product for the formation; this would chmacterize the effectiveness of the formation below the producing interval. INTRODUCTION In many oil and gas reservoirs the producing wells are completed as partially penetrating wells; that is, only a portion of the pay zone is perforated. This may be done for a variety of reasons, but the most common one is to prevent or delay the intrusion of unwanted fluids into the wellbore. This paper studies the effects of partial penetration on the pressure distribution resulting from the production of a compressible liquid at a constant rate. To simplify the mathematical analysis the case of a single well located in an infinite reservoir of constant thickness is considered, and it is assumed that this well is perforated over an interval adjacent to the upper (or lower) impermeable boundary of the formation. A well producing from an arbitrary interval within the bulk of the formation could be treated in a similar way, but this action would merely add to the complexities of the solution and contribute little to the appreciation of the over-all effects of partial penetration. In a recently published paper by Odeh,10 the more general problem of producing from an arbitrary interval within the pay zone was studied for the quasi-steady state flow of a compressible liquid, This is the case in which there is a a potential at the outer boundary and a constant flux across the same boundary. This contrasts with the problem studied here, which is concerned with the nonsteady-state behavior in an infinite reservoir. The exact solution of the partial penetration problem presents great analytical problems because the boundary conditions that solutions of the partial differential equations must satisfy are mixed; i.e., on one of the boundaries the pressure is specified on one portion and the flux on the other. This difficulty occurs at the wellbore, for the flux over the nonproductive section of the well is zero, and the potential over the perforated interval must be constant. In the case of constant rate production from the well, this uniform potential is time dependent and unknown, and the additional condition that where hl is the thickness of the perforated interval, must also b'e satisfied. This problem may be overcome in the case of constant rate production by making the assumption that the flux into the well is uniform over the entire perforated interval, so that on the wellbore the flux is specified over the total formation thickness. This approximation naturally leads to an error in the solution since the potential (pressure) will not

Jan 1, 1970

By John G. Simmons

A tutorial account of the tunnel effect between metal electrodes separated by a thin insulating film is presented. Energy diagrams of metal-insulator -metal sandwiches are briefly discussed, and the isothermal and thermal J-V characteristics for symmetric and asymmetric tunnel junctions are derived from a generalized expression. Experimental data from tunnel junctions are presented, and it is shown how, correlation between theory and experiment permits a determination of some of the oxide properties. Finally, the barrier heights in AT-Al2O3-A1 junctions determined by various inr3estigators are discussed. The object of this paper is to give a tutorial account of the electric-tunnel effect between metal electrodes separated by a thin insulating film and to illustrate its utility in the study of metal-oxide interfaces. This paper will emphasize the theoretical aspects of the electric-tunnel effect: however, a brief account of the more recent experimental work will be presented. A more comprehensive experimental study of the tunnel effect will be presented in the following paper by Drs. Pollack and Morris, see p. 497. We will open with a discussion of the energy diagrams for metal-insulator-metal junctions and what we mean by the electric-tunnel effect. Following this is an account of the theoretical studies of Sommerfeld and Bethe, and Holm, and the recently reported calculations on symmetric and asymmetric junctions using the generalized formula. The theoretical presentation is concluded with calculations on the temperature dependence of the tunnel J-V characteristic. In the experimental section, it is shown how barrier heights and thicknesses are determined by comparing the experimental data with the theory. Finally, the results of various investigators on the determination of the barrier heights in Al-Al2O,-A1 systems are discussed. I) POTENTIAL BARRIERS BETWEEN CLOSELY SPACED ELECTRODES Since it is necessary to supply energy to a metal in order to observe electron emission from its surface, it is evident that the potential energy of an electron within a metal is lower than that of an electron at rest outside the metal. It follows, then, that the electron must undergo a change in potential as it crosses the metal-vacuum interface. In the Sommerfeld1 free-electron theory of metals it is assumed that the free electrons, the electrons responsible for the electrical characteristics of metals, move in a constant potential environment in the metal, and are contained within the metal by a potential barrier at the metal-vacuum interface. It will be evident that the idea of a constant potential environment is a very idealized model, since the potential energy of an electron is influenced by all of the atoms and the other electrons within the metal; however, its use is justified by the many excellent results it gives.2 Fig. l (a) is the energy diagram of the model envisaged by Sommerfeld; the metal is represented by a potential-energy well of depth V,; the vacuum level represents the energy of an electron at rest outside the metal. At 0°K the electrons, which exist in pairs in discrete energy levels, fill up the well to an energy ?, the Fermi level. The distance, Vo - ?, from the Fermi level to the vacuum level is known as the work function of the metal, and represents the minimum energy required to free electrons from the interior of the metal at 0°K.

Jan 1, 1965