Search Documents

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949

By J. E. Stukel, J. Cocubinsky

A CONSIDERABLE amount of information is available on the equilibrium distribution of manganese between slag and metal under oxidizing conditions. These data have increased our knowledge of the manganese reactions in the open hearth, ladle, and ingot mold. In contrast, there is a paucity of data on the slag-metal distribution of manganese under reducing conditions. The purpose of the present investigation was to study the equilibrium distribution of manganese between blast-furnace type slags and iron saturated with carbon. Experimental Method Furnace: The induction furnace used for the experiments is shown in Fig. 1. A 1 in. pipe, attached to the transite cover, was fitted with a window through which the charge could be observed. Material could be introduced into the furnace through a tee and plug without removing the cover. A graph-it cylinder (3 in. ID and 10'/2 in. long), centered within the induction coil, was used as a heating element. During a test, a zircon plug kept the top of the furnace from becoming too hot from heat radiation. At the bottom, a graphite block on the vertical center line of the furnace and extending 1 1/2 in. into the coil, was used as a support for the graphite crucibles containing the melt. The graphite crucibles, machined from regular carbon electrode stock, had a 2% in. OD with 3/16 in. walls and were 5% in. long. The fumes present in the furnace during the early part of a run made optical readings uncertain. A noble metal thermocouple was, therefore, adopted to measure the temperatures. The arrangement used, shown in Fig. 1, allowed the silmanite protection tube to be replaced with a minimum effort. The thermocouple was calibrated against a standard Pt-Pt-Rh thermocouple in a fused quartz protection tube. The latter was inserted in the molten iron by removing the glass window on the cover. The lower couple was found to be very sensitive to temperature changes. To insure accurate temperature readings, the graphite crucibles were made to fit tightly against the silmanite protection tube. Further, to avoid contamination of the thermocouple by carbon, the silmanite tube was changed and the calibration procedure was repeated at frequent intervals. By using this temperature measuring technique, the furnace was easily held within *1O°C of the desired temperature. Because of the small free space in the furnace, no attempt was made to control the atmosphere. It

Jan 1, 1955

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By Thomas Clagett

THE Pocahontas coal field comprises the area in Tazewell County, Va., and Mercer and McDowell Counties, W. Va., in which Nos. 3 and 4 Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305m.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now, about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, io which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks off bone, each from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 25 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficiently well defined to exert an influence on the mining is rare. Overlying strata are slates, shales, and sandstones, the sandstones predominating, extending from .30 to 1000 ft. above No. 3 seam. The strata directly above the. draw slate of No. 3 seam, or "black rash" of No., 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the

Jan 5, 1922

By William L. Fink, Kent R. Van Horn

Zinc is one of the effective elements introduced to enhance the strength of aluminum. This strengthening is principally attributable to the high solid solubility of zinc in aluminum and the pronounced variation of solubility with temperature. Consequently an accurate determination of the solid solubility curve is desirable. The solid solubility relations have been studied by numerous investigators. Shepherd1 first established the existence of a solid solution region at the aluminum end of the diagram (-v phase) by specific volume and microscopic determinations. Bauer and Voge12 published a constitutional diagram which showed the limits of solid solubility as determined by thermal and microscopic methods. Hanson and Gayler3 presented the aluminum-zinc diagram which is now most generally accepted (Fig. 1). Chill-cast samples were given thermal treatments designed to obtain equilibrium conditions, quenched, and microscopically examined. The solubility was placed between 15 to 20 per cent at 60" C., 20 to 22 per cent at 140" C. and 36 to 38 per cent at 270" C. Sander and Meissner decidedly modified the limits of the -y phase field of Hanson and Gayler's diagram by using similar methods on chill-cast specimens annealed for a shorter period of time. Tanabe,s utilizing dynamic hard-ness, electrical conductivity and dilatometric measurements of specimens at temperature, obtained values comparable to Hanson and Gayler's at room temperature, but appreciably lower at higher temperatures. Nishimura6 concluded from age-hardening results of aluminum-zinc alloy chill castings, which had been quenched from 400" to 500" C., that the solubility of zinc in aluminum at room temperature is less than 5 * Metallurgical Division, Aluminum Research Laboratories. 1 E. S. Shepherd: Aluminum-Zinc Alloys, Jnl, phys. Chem. (1905) 9, 504. 2 0. Bauer and 0. Vogel: Aluminum-Zinc Alloys, Int. Jn1. Melallog. (1916) 8, 101. 3 D. Hanson and M. V. L. Gayler: A Further Study of the Alloys of Aluminum and Zinc. Jnl. Inst. Met. (1922) 27, 267. 4 W. Sander and K. L. Meissner: ZII~ Kenntnis der Konstitution der Aluminium-Zinklegierungen. Ztsch. f. Metallkunde (1922) 14, 385. 4 T. Tanabe: Studies in the Aluminum-Zinc System, Jnl. Inst. Met. (1924) 32, 415 6 H. Nishimura: On the Age-Hardening of Aluminum-Rich Al-Zn Alloys. Mem. Kyoto Imp. Univ. (1924) 3, 133.

Jan 1, 1932

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

By A. H. Duane, A. E. Miller

The high-temperature allotropy of some heavy rare-earth metals and their alloying behavior with magnesium in the 0 to 50 at. pct Mg region was studied by thermal, microscopic, and X-ray methods. Examination of a hcc phase retained upon quenching alloys of different magnesium content confirmed the existence of a bcc high-temperature allotrope in pure gadolinium, terbium, dysprosium, holmium, erbium, thulium, and lutetium. The lattice constants of the pure metals were determined from a Vegard's Law extrapolation and .found to be 4.05, 4.02, 3.98, 3.96, 3.94, 3.92, and 3.90 + 0.02 A, respectively. In all of the systems studied, the high-temperature bcc phase decomposed eutec-toidally, when slowly cooled, into a hexagonal rare earth-Mg solid solution and a simple-cubic peritec-tic AB-type compound. In 1956, Spedding et al.' observed high-temperature resistivity anomalies in the light rare-earth metals and made several unsuccessful attempts to retain the high-temperature form of these materials at room temperature by quenching the pure metals from temperatures near their melting points. High-temperature X-ray techniques were used by Spedding et a1.' in 1959, to investigate the high-temperature allotropy of the rare-earth metals. This study showed that lanthanum, cerium, praseodymium, neodymium, ytterbium, and possibly gadolinium are bcc at temperatures near their melting points. Discontinuous changes in resistivity at elevated temperatures were also observed for pure gadolinium, terbium, dysprosium, holmium, and lutetium, thus indicating the possible existence of a high-temperature crystalline transformation in these metals. However, due to experimental difficulties encountered in the high-temperature X-ray analysis of these metals, their allotropic form was not identified. Spedding et a~.~ in 1960 observed that yttrium displayed a continuous solid solubility with lanthanum at elevated temperatures, thus showing the high-temperature structure of yttrium to be the same as that of lanthanum, i.e., bcc. Similarly, the high-temperature alloying behavior of gadolinium with yttrium showed gadolinium to be bcc at elevated temperatures. The bcc nature of the high-temperature form of yttrium was again recognized in 1960 by Eash and carlson4 in their study of the alloying behavior of yttrium with thorium. Gibson and Carlson, in a similar study of the alloying behavior of yttrium with magnesium, found that by quenching Y-Mg alloys from within the 0-solid solution region, Fig. l, they were able to retain the allotropic form of yttrium. It was the present authors' intention to use this method to show the existence of a bcc high-temperature form of the heavy rare-earth metals gadolinium, terbium, dysprosium, holmium, erbium, thulium, and lutetium. Simultaneous with the present work, Beaudry and Daane' have shown the bcc nature of the high-temperature form of scandium. EXPERIMENTAL PROCEDURES Materials. The rare-earth metals used in this study were prepared by the calcium reduction of the fluoride and were further purified by vacuum distillation. The magnesium was obtained from the New England Lime Co. and was also purified by distillation prior to its use in the preparation of the rare earth-Mg alloys. The results of chemical and spec-

Jan 1, 1964

By P. W. Bridgman

FLOW and fracture are admittedly complicated phenomena of which we are yet only partially masters. There is not even universal agreement as to the details of the language best adapted merely to describe the phenomena, to say nothing of any theory. Certain points of view, however, are widely held, and there are certain general expectations as to what sort of procedures will prove permissible. A complete description of any situation involving fracture would demand a complete history of all the variables in the control of the experimenter. The experimenter endeavors so to choose his independent variables that they are adequate to determine completely the situation in the sense that when an experiment is repeated on the same initial material and with the independent variables running through the same sequence, all the other measurable properties of the system will also run through the same course. It is, I think, the universal conviction that when we are dealing with phenomena of flow and fracture, the most important of the necessary variables are the external forces acting on the various parts of the body; when the force history repeats, with certain obvious restrictions such as that temperature must be constant and non- mechanical forces, such as magnetic field, must be small enough to be ineffective, then the history of all measurable properties will repeat; in particular the alteration of geometrical shape due to flow will run through the same course, and when fracture comes, the character of the fracture will be reproduced. Complete mastery of merely the descriptive aspects of flow and fracture would demand the ability to predict the entire course of flow and complete characterization of the final fracture for every possible combination of forces, varying in time in all possible ways, when applied to bodies of all possible shapes. This full situation is obviously of prohibitive complexity. The first stage in reduction to manage- able simplicity is to resolve the total situation into the sum of contributions made by small elements. Our thesis is that if each of the elements is adequately characterized, the behavior of the whole system is fixed. The element is usually taken of a simple geometrical shape, suggested by the mathematics best adapted to the particular situation. The forces acting across the faces of the elements are ultimately determined by the forces acting across the free faces of the whole system. The detailed process of finding the precise forces on the faces of all the elements in terms of the external forces involves the use of a special mathematical invention, the stress, a constructional quantity consisting of six components. The stress at any point in the body is determined by both the external force system and by the physical properties of the body at all points; quite different stresses prevail at the interior of bodies of the same shape under the same external forces in the elastic and plastic ranges. The forces on the faces of any element are, however, uniquely determined by the stress system at the element. Our fundamental thesis

Jan 1, 1944

By Howard N. Evanenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. AVERAGE RECOVERY The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered-it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal-is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1946

By P. Beardmore, A. H. Holtzman, M. B. Bever

Specimens of the alloy CU3AU in the ordered and disordered states were subjected to explosive loading at shock pressures in the range from 160 to 475 kbars. The resulting changes in the resistivity, stored energy, microhardness, and microstructure were determined. By comparing the effects of explosive loading on ordered and disordered specimens a separation of structura1 and configurational changes has been made. In the pressure range from 290 to 370 kbars, representing a small increment of strain, the degree of long-range order in the ordered alloy decreased sharply. This change is attributed to the generation of shear stresses in excess of the theoretical shear strength of the alloy. Disordered CU3AU under explosive loading behaves in a manner considered to be characteristic of fee solid-solution alloys generally. The response of metals to high-velocity deformation and, in particular, to explosive loading has attracted much interest in recent years.' In general, metals are substantially strengthened by the passage of shock waves although the permanent strains are small. Explosive loading induces this strengthening by causing the metal to undergo rapidly a transient strain in a narrow region, first in the shock front and then in the rarefaction wave, which releases the pressure. The transient strain is given by e = 4/3 In V/Vo, where Vo and v are the specific volumes in the uncompressed and compressed states.2 The process produces many defects, which account for the strengthening. For the investigation reported here, an ordered alloy was chosen because it was expected to give sensitive indications of the near-neighbor effects produced by shock waves. The ordered alloy CU3AU was of special interest because of past work on the effects of conventional deformation on this alloy.314 The disordered alloy was included as a standard for comparison and as an alloy typical of a solid solution containing short-range order. The effects of explosive loading were followed by measurements of the resistivity, stored energy, and microhardness, and by metallographic examination. EXPERIMENTAL PROCEDURES Preparation of Specimens. Part of an ingot of the alloy Cu3Au prepared previously4 was cold-rolled with several intermediate anneals in vacuum to a final thickness of 0.042 in. Specimens of dimensions 2.0 by 1.0 by 0.042 in. were machined from this strip. After a recrystallization treatment of 1 hr at 565oC, half of the specimens were disordered by heating in evacuated Pyrex capsules for 1 hr at 460°C and quenching into water. Although they contained short-range order, they will be referred to as 'disordered" to indicate the absence of long-range order. The rest of the specimens were cooled slowly from 380°C to induce long-range order. The grain size of the ordered and disordered specimens was 0.012 mm. Explosive Loading. This was carried out at the Eastern Laboratory, Explosives Department, E. I. du Pont de Nemours & Co., by a driver-plate procedure described elsewhere.2 Two ordered specimens were stacked alongside two disordered speci-

Jan 1, 1964

This book has employed miners' narratives to illustrate basic concepts about the escape process. One of the most powerful means by which people make sense of their experiences is through the telling and internalization of stories [Bruner 1990]. By couching one's own and others' motives and actions in terms of a coherent narrative, a person is able to learn from mistakes and plan future behaviors that may help ensure survival. A growing body of research suggests that decision-making skills used to deal with emergency situations can be taught and assessed by simulations based on narratives from the real world [Bransford et al. 1986; Brecke 1982; Brener 1984; Connolly et al. 1989; Halff et al. 1986; Jones and Keith 1983; Lacefield and Cole 1986]. Such techniques have been used to address the decision-making of medical personnel, civil and military flight crews, and even people involved in broader life events such as political and military situations [Babbott and Halter 1983; Dugdale et al. 1982; Farrand et al. 1982; Gilbert 1975; McGuire 1985; McGuire et al. 1976; Flathers et al. 1982; Giffin and Rockwell 1984; Jensen 1982; Janis and Mann 1987]. Given the validity of this method of study and the promise it holds for helping people improve the quality of their responses to nonroutine occurrences, it is perhaps surprising that there have been no studies of emergency decision-making among blue-collar workers prior to those conducted by the present authors and their colleagues. The purpose of this chapter is to describe underground coal miners' decision-making performance on a table-top simulation whose problem structure is derived from interviews with a group of eight miners who escaped from the 5 Left section at Brownfield Mine. The exercise was constructed by a panel of domain experts (mine safety and rescue personnel) with the assistance of an educational psychologist. The simulation includes actual predicaments with wise and unwise decision alternatives that, in the opinion of these domain experts, are characteristic of such escapes. Results reported in this chapter are the scores of a sample of experienced mine workers who completed the simulation. Because the exercise is a series of objective performance tasks coupled with detailed and immediate feedback, this simulation can be used to teach and refresh critical escape skills, as well as to provide data concerning the proficiency of miners at the time of exercise administration.

Jan 1, 2000

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By H. L. Gilbert, H. A. Johansen, R. G. Nelson

High purity electrolytic chromium plate has been hydrogen-reduced and arc-melted under inert atmosphere to give sound ingots. These ingots may be hot forged to break the as-cast structure and then worked at 500°C to finished form. An intermediate and final high temperature anneal gives best ductility and grain refinement. HE increasing interest in refractory metals for I use in high temperature gas turbines, jets, and rockets has led to great efforts in exploiting the fifth and sixth groups of transition elements. Much of the interest has centered upon production of metals that can be worked and fabricated by normal means to produce various engine parts or components having the high temperature characteristics of oxidation resistance and high creep strength required for such uses. If these pure elements do not exhibit all of the desired characteristics, it may be possible to obtain a high purity alloy that will. Since, in all cases, development of these transition elements has depended to a large extent upon removal of oxygen and nitrogen as a means for producing ductile metal, the hypothesis has been accepted that oxygen is the normal embrittling material in a high grade electrolytic chromium metal. Various methods have been employed in an effort to remove this oxygen by direct or indirect attack.' Many workers have endeavored to produce pure chromium through reduction of the oxide by carbon or active metals, while others have recommended fusion electrolysis of chromium salts or reduction of these salts by active metals, such as sodium or calcium. Hydrogen reduction of the oxide or chloride and thermal dissociation of the iodide have been reported to give high purity metal. Experimental Work The U. S. Bureau of Mines, Northwest Electro-development Laboratory, has systematically re-examined the more promising methods and developed two which produce metal having ductility at temperatures lower than heretofore described. It has been found' that oxide-free chromium chlorides in a NaCl-KCl carrier salt may be mag- nesium-reduced and the byproduct salts distilled off in vacuo to give a high purity chromium sponge. Fusion analysis conducted under the supervision of W. W. Horton of Knolls Atomic Power Laboratory showed the oxygen and nitrogen both to be below 10 parts per million on a selected sample. A small amount of carbon is carried over in the final metal from the chlorination and reduction steps which are carried out in graphite crucibles. This trace of carbon is not detrimental to hot ductility. A more practical method for producing ductile metal is through hydrogen reduction of high purity electrolytic chromium. Normal electrolytic chromium will, if "developed" for a few minutes at 1100°C in high vacuum, be found by the method of Adcock:; to contain about 1 pct chromium sesquioxide (Cr2O3). This small amount of oxygen may be effectively reduced by hydrogen.2, 4 The method employed was to crush electrolytic chromium plate in a gyratory crusher to pass 60-mesh; finer crushing appears to offer no advantage. A nitric acid leach removed the iron picked up during crushing. The leached powder was rinsed until neutral with distilled water and vacuum-dried.

Jan 1, 1954

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .&apos; Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation&apos;s three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation&apos;s high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California&apos;s current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California&apos;s portion of the talc-

Jan 1, 1951

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .&apos; Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation&apos;s three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation&apos;s high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California&apos;s current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California&apos;s portion of the talc-

Jan 1, 1951

By R. M. Brick, J. T. Richards

Tests have been conducted to determine the mechanical properties of several beryllium copper alloys down to liquid air temperatures. The materials investigated include beryllium copper, beryl-lium-cobalt-copper, and beryllium-zinc-copper in the wrought and cast conditions. As a means of evaluation, the influence of cold work and age hardening treatment upon subzero behavior has been observed. The effects of temperature upon both elastic and plastic deformation are also considered. THE low temperature mechanical properties of beryllium copper are of current interest in view of the increasing number of subzero applications. At extremely low temperatures, beryllium copper components are employed in temperature control and gas liquefaction equipment. At more moderate temperatures, such as those encountered in arctic regions, these alloys find use in a wide range of civilian and military applications. Although several previous subzero investigations have included beryllium copper,&apos;-&apos; none have been complete with respect to test temperatures or materials employed. As indicated in Table I, the alloy: used by Colbeck and MacGillivray,1 Walle,2 and Kostenets&apos; were nonstandard and were not representative of present commercial practice. In addition, Kostenets4 did not test age hardened specimens, while the temperature in the other investigations", "-&apos; were not carried below —100°F. These tests, however, indicate that beryllium copper offers interesting possibilities in subzero atmospheres, since the increase in strength with decreasing temperature is not accompanied by a reduction in ductility or impact resistance. As a means of checking and extending this earlier work at subzero temperatures, an investigation was undertaken at the University of Pennsylvania. In addition to testing the standard 2 pct beryllium copper, other alloys were also considered in wrought and cast forms. Charpy impact and tension tests were included with particular emphasis on the elastic characteristics, since beryllium copper is frequently selected for its spring qualities. Nominal test temperatures were +80°, —75", —200°, and —300°F. Test Materials Wrought beryllium copper, beryllium-cobalt-copper, and beryllium-zinc-copper specimens were machined from 0.560 in. diameter rod. These alloys were tested in the solution treated, cold drawn, or age hardened conditions. In the case of solution treated beryllium copper, some specimens were aged (3 hr at 600°F) for maximum hardness and others were overaged (1 1/2 hr at 750°F) to determine the effect of heat treatment. The compositions and average room temperature properties of these wrought alloys are presented in Table 11. The casting alloy versions of beryllium copper and beryllium-cobalt-copper were prepared as sand-cast cylinders, roughly 3/4 in. diameter x 6 in. long. Test specimens were machined from these cylinders. Conditions tested included as cast as well as solution treated and age hardened. Table 111 lists compositional and room temperature property data for the cast alloys. Test Methods Tension tests were conducted on specimens having a 0.25 in. diameter reduced section over a 1 in. gage length. To insure axiality, specimens were loaded by means of hardened chains. The yield strength at 0.2 pct offset was obtained from autographically recorded stress-strain curves resulting from a spe-

Jan 1, 1955

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947