Search Documents

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By Samuel L. Hoyt

This paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use. The samples used were 5 to 6 mils thick and about 1 in. square. They were placed between iron blocks and set in the hot zone of a nichrome furnace which had been brought to the desired temperature Time was taken from the moment the samples reached the furnace

Jan 1, 1929

By R. G. Davies

Isothermal annealing of quenched Fe3Al reveals that the superlattice forms by the nucleation and growth of ordered domains. The activation energy for isothermal ordering and initial domain growth is -29 keal per mole, which is thought to he the activation energy for vacancy migration. Domain growth, in the absence of excess vacancies, has an activation energy of -100 keal per mole. A maximum in the hardness is observed when the structure consists Of ordered domains, -35-4 in size, growing into a short-range ordered matrix and, also as a function of degree of order, S, with an infinite domain size at S = 0.4 to 0.5. It is proposed that both maxima are due to a transition from deformation by unit dislocations to deformation by superdislocntions. FE-AL alloys containing more than -23 at. pet Al, when quenched from above the critical temperature for the Fe3A1 type of order, always contain the maximum possible amount of FeAl (B2) type of order' (see Fig. 1). Thus when the Fe3A1 superlattice forms, in a 25 at, pet A1 alloy, it does so from an imperfect FeAl structure. The formation of the Fe3Al superlattice has been the subject of several recent X-ray,1, 2 electrical-resistivity,3"6 and dilatometric3 investigations. McQueen and Kuczynski3 concluded that the isotherma1 ordering of Fe3Al, after quenching from 800°C (T,, the critical temperature for order, is 55O°C), takes place by the nucleation and growth of ordered domains. However, Feder and Cahn4 found that the isothermal ordering was complex but more like a homogeneous nucleation process than a nucleation and growth process. Lawley and Cahn2 reported that the degree of order is a continuous function of temperature which is a characteristic of a homogeneous nucleation process. Thus, the evidence is conflicting as to the nature of the Fe3Al ordering reaction. Lipson7 was the first to suggest that ordered domains should exist in the Fe3A1 structure since, as

Jan 1, 1964

By George Wendell

THE fact that a symposium on pyrometry is being held under the auspices of the American Institute of Mining and Metallurgical Engineers may very properly be taken as a recognition of the importance of temperature measurements and control in production and in the industries, and of the need for instruction in pyrometry in our schools of engineering. Though there may be general agreement as to the need of some instruction along this line, there will undoubtedly be divergence of opinion as to the amount of time that can be allowed to such instruction, as well as to its character. Those who have given little attention to the complexity of high-temperature measurements will be apt to think that a few simple experiments are all that is required. They fail to distinguish between the artisan, who merely has to learn how to use any piece of apparatus that is installed, and the technically trained man, who must be prepared to assume the responsibility for the supervision and maintenance of the pyrometric equipment, for the calibration of the instruments, and for the solution of any temperature problems that arise. In approaching this subject two questions present themselves: What should be the character of the instruction in pyrometry in an engineering school, and what can be expected of the students who have had this instruction? In brief, it may be said that the aims of a course in pyrometry should be to give: (1) A thorough grounding in the fundamental principles of thermoelectric, resistance, radiation, and optical pyrometry, and of liquid and gas thermometry; (2) practical instruction in the calibration of pyrometers; (3) acquaintance with the errors that are likely to arise and the precautions that must be observed in practice; (4) information regarding the limitations of the various classes of instruments, their relative reliability, and the accuracy attainable with them at different temperatures; (5) acquaintance with the commercial instruments on the market, their construction and relative merits; (6) a knowledge of the chief sources of information relating to the measurement of high and low temperatures. To sum up, the aim should be to turn out resourceful young men familiar with the leading instruments on the

Jan 9, 1919

By John T. Crawford

Much has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of — 48-mesh material. The percentage of this —48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The tonnage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reasonable cleaning job down to and including +l00 mesh, by far the greater majority stop at or short of the + 48-mesh size. Much of the literature on coal flotation passes by the fred pulp density and size by merely stating that the feed varies from 20 to 30 per cent solids and that the size range is from — 1/4 in. or — 1/8 in. to 0. Small wonder then that some operators with entirely different conditions, and not knowing the machine capacity, throw up their hands in despair when flotation is mentioned. Too much parallel is drawn between flotation methods as applied to ores and as applied to coal, to the detriment of the latter. In the flotation of metalliferous ores the feed pulp density ranges from 20 to 30 per cent solids, depending upon the amount of mineral to be floated and upon the size analysis. Thus where 2 to 5 per cent of the

Jan 1, 1936

By John T. Crawford

Much has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of — 48-mesh material. The percentage of this —48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The tonnage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reasonable cleaning job down to and including +l00 mesh, by far the greater majority stop at or short of the + 48-mesh size. Much of the literature on coal flotation passes by the fred pulp density and size by merely stating that the feed varies from 20 to 30 per cent solids and that the size range is from — 1/4 in. or — 1/8 in. to 0. Small wonder then that some operators with entirely different conditions, and not knowing the machine capacity, throw up their hands in despair when flotation is mentioned. Too much parallel is drawn between flotation methods as applied to ores and as applied to coal, to the detriment of the latter. In the flotation of metalliferous ores the feed pulp density ranges from 20 to 30 per cent solids, depending upon the amount of mineral to be floated and upon the size analysis. Thus where 2 to 5 per cent of the

Jan 1, 1936

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By A. D. Shuloyakov, G. A. Finkelstein, V. I. Kurets, A. K. Vedin

"In disintegrating solid ores with mineral values disseminated in them, one of the principal tasks is to selectively separate valuable mineral particles from the matrix in which they reside, striving at the same time to keep their natural shape and size as intact as possible.The conventional mechanical disintegration methods do not meet this most important requirement in full. The other major objective here is to reduce electric power consumption during the fragmentation stage, since up to 65 per cent of the total power consumption at concentrators processing ores of non-ferrous, ferrous, rare, and precious metals is spent on disintegration steps.Numerous experiments conducted on dozens of ore types (tin, tungsten, and many others, as well as on rock containing diamonds, rubies, emeralds, etc.) have invariably demonstrated by far superior integrity of mineral values as compared with that obtained by mechanical as well as other types of disintegration.However, the process remains as power-intensive as ever which is due to the imperfect nature of the electro-technical devices that convert the network electric current into high-voltage electric impulses responsible for the disintegration process.The maximum capacity attained in disintegrating the hardest materials from 40 mm to 2 mm size in a single operating chamber with four high-voltage electrodes does not exceed 1.0-1.5 t/h. Attempts at increasing the number of electrodes and the capacity of the operating chamber have failed so far because of high overall dimensions and mass of the electrical part of the installation supplying the chamber with pulsating current, as well as of the commutation requirements. At the same time, a number of overseas operations have reported a significant breakthrough in their attempts to reduce dozens of times the overall dimensions and mass of the discharge impulse generating installation (EIS), which enables us to contemplate to increase the capacity of the EIS at least ten times in the nearest future. Yet, even with the currently achieved capacity of the EIS, these installations have found wide use in geological surveying, precious and semi-precious stones production, in grinding super hard materials, etc., since they provide spectacular selectivity of disintegration and thus the integrity of valuable mineral crystals."

Jan 1, 2003

By S. H. Davis

THE pyrites used in making sulfuric acid in the United States have been largely imported from Spain and Canada, the Spanish imports amounting to nearly 1,000,000 tons per annum in the pre-war period. The greatly increased use of sulfuric acid and the cutting off of these Spanish imports, incident to war conditions, brought about a threatened shortage of sulfur supplies during the war period. The bituminous-coal mines of certain districts have, for many years, furnished a small tonnage of pyrite in the form of coal brasses. A mechanical concentrator at Danville, Ill., for a number of years, has been treating hand-picked lump pyrite and coal from the picking belt and from the mines and a small plant near Gillespie, Ill., for a few months has been recovering pyrite from washery refuse. Many mines throughout Illinois, Indiana, Western Kentucky, Ohio, and Pennsylvania have shipped an occasional car of the hand-cleaned lump pyrite. Only a very small percentage of the available pyrite has been recovered in this way, however, as usually the miners throw such lumps into the gob with slate and other impurities. It has been estimated that the western Indiana coal field could furnish more than 100,000 tons of pyrite per annum. The present production is very small. The possibility of furnishing the domestic trade with pyrites recovered as a byproduct from coal-mining operations appears attractive but there are certain features difficult to overcome. Pyrite, to be used in acid making, must meet with certain requirements as to size and purity. Lump ore for grate burners should be under 3 in. (7.6 cm.) and over 1 in. (2.5 cm.) in diameter. Fines for use in mecnanical roasters should be under quarter mesh. The material should be high in sulfur, free from arsenic and phosphorus, and as low in carbon as possible. The pyrite obtained from coal can be made to meet all the above requirements, but it is difficult to remove all the carbon. The pyrite in coal occurs as bands and nodules of varying thickness and size and of comparative purity, but mixed with this is more or less web sulfur. The web sulfur carries with it admixed coal, which may make the concen-

Jan 8, 1919

By P. Barnes

It may he of interest, and perhaps of inzportance, to the members of the Institute that specific mention should be made in detail of the great value of this method of copying or photographing all kinds of tracings." Several samples are laid upon the table which may serve as illustrations of the results obtained. Some of these show slight imperfections, depending upon the character of the tracing, and upon the length of the exposure to the light, but it may be clearly seen that even a faint copy would be quite available for actual use. The process is believed to be of French origin, and has been used for many years. Special attention seems to have been directed to it recently, and its great value to engineers appears likely to be fully recognized. The manipulations required are of the simplest possible kind, and are entirely within the skill and comprehension of any office boy who can be trusted to copy a letter in an ordinary press. These particulars may be summarized somewhat thus: 1. Provide a flat board as large as the tracing which is to be copied. 2. Lay on this hoard two or three thicknesses of common blanket, or its equivalent, to give a slightly yielding backing for the paper. 3. Lay on the blanket the prepared paper with the sensitive side uppermost. 4. Lay on this paper the tracing, smoothing it out as perfectly as possible so as to insure a perfect contact with the paper. 5. Lay on the tracing a plate of clear glass, which should be heavy enough to press the tracing close down upon the paper. Ordinary plate-glass of 3/8" thickness is quite sufficient. 6. Expose the whole to a clear sunlight, by pushing it out on a shelf from an ordinary window, or in any other convenient way, for six to ten minutes. If a clear skylight only can be had, the exposure must be continued for thirty or forty-five minutes, and under a cloudy sky, sixty to ninety minutes may be needed.

Jan 1, 1879

By Wilhelm Rohn

When a metal solidifies, gas, initially present in solution, may be concentrated at the grain boundaries, leading to brittleness, or it may form solid compounds which, if localized at the grain boundaries, impair the properties. On the other hand, the solid compounds formed sometimes distribute themselves more or less uniformly, and hence may be relatively harmless. If metallic oxides are heated under a partial oxygen pressure less than that corresponding to the dissociation pressure of the oxide in solution in the melt, they will decompose and oxygen will tend to be eliminated from the melt. This paper presents data on the partial oxygen pressures of copper and nickel oxides over a wide range of temperatures; it also presents data regarding the amount and nature of the gases evolved in the vacuum melting of a 3500-kg. charge of nickel-chromium alloy and gives test values indicating the improvement in impact values ascribed to vacuum melting. The results of commercial experience with a 4-ton vacuum melting and casting furnace indicate that this method entails an increase in cost of about 10 cents per pound of ingot over orthodox practice, which may be justified for special products and may be lowered if hot metal is charged into the vacuum furnace. DISCUSSION (Howard Scott presiding) J. H. ScafF, New York, N. Y. (written discussion).—In the section of Dr. Rohn's paper describing the effect of melting -metals in vacuo, he says, "In this way plain copper, nickel and iron may be easily purified. For example, vacuum-melted copper does not contain any oxygen and for this reason it is never sensitive to hydrogen embrittlement." This statement is contrary to the results of our experiments at the Bell Telephone Laboratories on the effect of vacuum melting on the properties of copper. Several 150-gram samples of tough-pitch copper were melted in a vacuum of the order of 1 X 10-5 to 1 X 10-6 mm. Hg for 2 hr. Portions of the ingots obtained were swaged to 0.100 in., then drawn to wire 0.050 in. in diameter for physical and

Jan 1, 1933

By George Stone

THE stack gases from regenerative furnaces are very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300° C. (572° F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450°. The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the .boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 10, 1913

By N. B. Wittman

Among the objects of interest which the members of the Institute are invited to examine in connection with this meeting is the Brown segmental wire-gun, which will be seen in process of construction at the works of the Pennsylvania Diamond Drill and Manufacturing Company, at Birdsboro. This is a 5-inch breech-loading (highpower) rifle, 19 feet long, constructed upon the system of Mr. J. H. Brown, an inventor of recognized genius in many branches of mechanical industry, and under the engineering direction of Lieutenant G. N. Whistler, Fifth U. S. Artillery. The system consists essentially of the subdivision of the inner core or tube of the gun, which takes up the initial compression, into longitudinal segments of such size that a higher physical condition and degree of special elasticity may be set up therein than it is possible to produce in the larger masses of metal heretofore used for the tube of the modern high-power cannon. The process consists in winding layers of square steel wire, subjected to a constant tension of 130,000 pounds per square inch, around these segments, which, when so held together, form the tube of the gun. A lining-tube may or may not be used. The steel segments used in the gun now under construction are 18 feet 4 inches long, and 3 inches thick at the breech, from which they taper to 0.8 inches at the muzzle. The physical condition of the segments has been determined by test-pieces, cut from each end of each segment, which show the following characteristics: Tensile strength, 165,000 pounds per square inch. Elastic limit, 105,000 pounds per square inch. Elongation at rupture, 14 per cent. in 2 inches. They are of crucible chrome steel, made by the Carpenter Steel Works, at Reading, Pa. The wire which holds them together has 0.005 square inches sectional area and is wound under a constant tension of 650 pounds on each strand, equivalent to 130,000 pounds per square inch. The winding has been done by a machine designed

Jan 1, 1893

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

1. Book reviews Phosphate rock, a bibliography of world resources. London, Mining Journal Books Limited, 1984. £10 (surface mail), £12.25 (airmail). Reviewer: P.Le. Grubb Ok Tedi, by William S. Pintz. London, Mining Journal Books Limited, 1984. 206 pp. £19 (surface mail), £22.25 (airmail). Reviewer: R.P. Plewman 2. Publications of the Canadian Mineral Policy Sector Lime by D.H. Stonehouse. 5 pp. Phosphates by G.S. Barry. 9 pp. Statistical summary of the mineral industry in Canada. 77 tables. Talc by M. Prud'homme. 6 pp. Zirconium by M.A. Boucher. 6 pp. Cement by D.H. Stonehouse. 13 pp. Gypsum and anhydrite by D.H. Stonehouse. 7 pp. Regional review by T.M. Buch. 12pp. SaltbyG.S. Barry. 7pp. Silicon, ferrosilicon and silicon carbide by D.G. Law-West. 6pp. SulphurbyB.W. Boyd. 9pp. Mineral Report 31. Canadian Minerals Yearbook 1981. Available from the above address at $40.75 per copy. 3. Mintek reports Report M18D The recovery of pyrite and gold from acid-leach residues from the Merriespruit Gold Mine. (First issued Feb. 1982; reissued Mar. 1984). Report M2OD The separation of ore from Cooke into high- and lowgrade fractions. (First issued Feb. 1982; reissued Mar. 1984). Report M33D Explanatory tests on the reduction of the sulphur content of sponge iron. (First issued Apr. 1982; reissued Mar. 1984). Report M43D Beneficiation tests on andalusite-bearing shales from a farm near Thabazimbi. (First issued Aug. 1982; reissuedMar. 1984). Report M129 The determination of tin, niobium, and tantalum in pegmatite by X-ray-fluorescence spectrometry. ReportM131 The determination of copper and nickel in iron- and chromium-bearing materials by a pressed-powder technique and X-ray-fluorescence spectrometry. Report M135 The installation of a 100 kV A plasma furnace at Mintek. The selection and installation of a 100 kV A a.c. plasma Report M136 The determination of gold in activated charcoal by use of a loose-powder technique and X-ray-fluorescence spectrometry. Report M140 The effect of physical and chemical factors on the corrosivity of a synthetic mine water.

Jan 1, 1984

By Ralph Nichols

The mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are the Pittsburg Idaho Co., Ltd.; the Latest Out Mining & Smelting Co., Ltd.; and the Oilmore Mining Co., Ltd. Besides the above propertiea, there are a number of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course and a dip to the west of from 40' to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine. Character of Ore. The ores of the district are oxidized, carrying an excess of iron over the silica (insoluble matter). The vein filling is a mixture of limonite and hematite, which is replaced by shoots of lead-silver ores. The lead minerals consist of carbonate of lead principally, but with small quantities of sulphide, sulphate, and other lead minerals.

Jan 1, 1914

By J. A. Solomon, H. E. Shafer

As a result of the great demand for metallic aluminum and the scarcity of domestic bauxite, numerous processes have been proposed and developed to extract the oxide of this metal (Al2o3) from clays, shales, and other low-grade raw materials.1-4 An exploratory study was made to extract alumina with sulfuric acid from relatively impure coal-associated draw-slate and to establish an optimum calcination temperature for maximum recovery. Draw-slate is the term used to describe the hard, slaty material directly overlying many coal seams and may range from a few inches to a few feet in thickness. Alumina content of these draw-slates may range from as low as 15% to over 35%. Although the following results are limited in scope, some of the data should prove beneficial for further work. Coal-associated clay, shale, and gob heretofore have been considered nuisance products; any successful alumina extraction process would greatly enhance the worth of these almost limitless resources. This research demonstrated that an optimum calcination temperature for alumina extraction could be established for a coal-associated draw-slate and that this temperature was lower than those suggested in previous work with unspecified clay types. It should be noted that slightly higher acid concentrations and somewhat finer particle sizes were used in this series of tests as compared to previous work. EXPERIMENTAL WORK Essentially, alumina extraction proceeded in four steps: 1) grinding, 2) calcining, 3) acid leaching, and 4) precipitating of aluminum sulfate. An initial series of reference tests to determine the optimum temperature of solubility for alumina was run using relatively pure kaolin. Kaolin forming clays are hydrous aluminum silicates of the approximate composition 2H2O A12O3 2SiO and kaolinite is the mineral that predominates in most kaolins. 5 The kaolin was ground to -30 mesh and subsequently calcined at temperatures ranging from 100°C to 700°C. Each sample was calcined for 1 hr in a muffle furnace and in turn subjected to sulfuric-acid leaching (H2SO4, 9 molar) for a 2-hr period. The filtrates were analyzed for the amount of dissolved alumina recovered.637 Also, each sample of leached or barren residue was

Jan 1, 1968

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

AT THE beginning of February the British Government announced acceptance of the American terms for funding the war debt, the main features-being as follows: Interest rate of 3 per cent. for the first 10 years and then 3 ½ per cent. up to the final extinguishment of the debt at the end of 62 years. The interest from the time since the loans were made to the actual beginning of the funding arrangement to be recomputed at 4 1/4 per cent. instead of the 5 per cent. rate now in effect. Congress ratified the contract respecting the British debt. The ship subsidy bill was relegated to the rear, which is indeed an end to the project. The natural consequence of this will be a liquidation of the Govern-ment's shipping business. The joint committee on the reorganization of Govern-ment departments made its report to the President. In general this seems to offer a well-considered plan for the coordination of Government service. The pro-posals respecting the bureaus that are particularly associated with the mining industry may be subject to criticism. According to the committee's plan, the Geological Survey remains in the Department of the Interior, but the Bureau of Mines and the compilation of the statistics of mineral production are transferred to the Department of Commerce. The Lausanne conference among the European powers came to an end early in February, without any treaty having been signed, owing to the refusal of the Turks to accept the ultimatum of the Allies. Theoreti-cally this left conditions in a state-of war between the Allies and Turkey. However, no actual movements have resulted. The French and Belgians continued to hold the Ruhr district of Westphalia, extending their lines and administration of the region. The Germans adhered to the policy of passive resistance. In the Parliament of Great Britain the French and Belgian policy was plainly declared to be unwise and dangerous. French and Belgian industries, moreover, were troubled by strikes among their own coal miners for higher wages. The Poles and Lithuanians engaged in border war-fare;. the civil war in Ireland continued. The rest of the world was quiet insofar as military operations are concerned.

Jan 2, 1923

By H. A. Wentworth

The Huff electrostatic plant of the United States Smelting CO., operated in conjunction with its wet concentrator at Midvale, Utah, was the second plant of substantial size installed using the Huff process, and the first plant to be put in operation on the so-called Western complex ores. , In spite of the machinery being of early design and consequently embracing many of the mechanical weaknesses incident to a pioneer plant the mill has operated steadily and uniformly since the summer of 1909, about five years now, without any material change other than some rearrangement of the machinery for better handling of the sizes. The ore, at present coming almost entirely from the company's mines in Bingham, is of practically the same composition as that upon which the plant was first put in operation. The crude ore, consisting of the sulphides of copper, lead, zinc, and iron, and containing small amounts of gold and silver, is brought by train and delivered to the hoppers of the wet concentrator, where by jig and table treatment, there are produced a shipping lead concentrate, a tailing, and a middling product, the latter being conveyed in push cars to the adjoining electrostatic mill. The crude ore delivered to the wet concentrator contains from 6 to 9.5 per cent. zinc. At times the plant is used also for the treatment of custom ores from the Bingham district and elsewhere, and at such times the results of the plant vary according to the material in use, but as by far the larger portion of the product is that from the company's own mines, the results given below are fairly indicative of the general work obtained. The diagram, Fig. 1, illustrates graphically the flow of the ore through the electrostatic mill. The middling coming from the wet mill, containing from 15 to 18 per cent. moisture, is hoisted while on the cars by an elevator, and delivered from the top of the elevator to a hopper over the drier. The drier first installed was of too low capacity to take care of the moisture present in the tonnage to which the mill was later

Jan 1, 1915