Search Documents

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900

A broad zone of intra-plate volcanism occurs for some 3000 km along the E. Australian coastal regions, extending from far northern Queensland southwards to Tasmania, westwards to western Victoria, and into southeastern South Australia. The age range, taken over the whole region, extends from Eocene to Holocene. Wellman & McDougall (1974) recognised the occurrence of three distinct types of volcanic occurrences: (a) Lava field provinces, dominantly basaltic and commonly strongly undersaturated, but of variable size. Large lava fields are especially exemplified by the younger provinces in northern Queensland (e.g. Nulla, McBride), and western Victoria. (b) Central volcano provinces, in which a reasonably well defined volcanic edifice is discernable. Such provinces are built of mildly undersaturated to saturated mafic lavas, but are also characterised by felsic volcanism (and often substantial mafic and felsic intrusive phases). Examples are the Springsure-Minerva Hills province, the Tweed and Focal Peak Shields (southeastern Queensland to northeastern N.S.W.), and the Nandewars, Warrumbungles, and Canobolas volcanic centres (N.S.W.). (c) A single leucitite province in N.S.W. Wellman and McDougall (1974) were able to show that the central volcano provinces exhibit a remarkably regular southward age migration pattern, the calculated migration rate being 66 + 5 mm yr , and these authors interpreted this in terms of the northward passage of the Australian plate across a fixed 'hotspot' within the upper mantle. The leucitite province also fits this migration pattern. The lava field provinces apparently exhibit more erratic regional age distribution patterns, but Sutherland (1981) has interpreted the data in terms of a multiple 'hotspot' model. It is noted, however, that the youngest areas of volcanism (Pleistocene 1. Department of Geology and Mineralogy, University of Queensland, St. Lucia, Brisbane, Queensland

Jan 1, 1987

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

The fraction of liquid phase in sintered ore can be the most important factor to determine the sinter quality and yield in sintering process. The generation ability of liquid phase for mixture of iron ore powders is determined by basicity, roasting time, roasting temperature and chemical composition of iron ores. Five different iron ores were selected in this study and the dried powders of iron ore and CaO reagent (<200 mesh) were homogeneously mixed together at their required proportions, then 15g of the mixture was pressed under a pressure of 20MPa to make a cylindrical sample with a diameter of 20mm. The sintering temperature in this study was kept at 1280℃, the gas phase is air, the holding time was varied with its three levels of 5min,10min and 15min. After that, the sample was cooled under room temperature in the air, and the cooled sample was analyzed by using zeiss optical microscope. The mineral phase compositions were quantitatively determined with an open source image processing software, Image J whicn can calculate the fraction of liquid phase. Besides, the study on how to estimate the sintering behavior of the raw materials in different conditions by the theoretical calculation is of vital importance, and the development of this will greatly improve the sintering production. Factsage will be used to calculate the liquid phases formulation during the sintering. Comparing the experimental results and the theoretical calculation shows that the mass of liquid phase increases with increasing basicity during the sintering, besides, the mass of calcium ferrite increases with increasing basicity. The generation ability of liquid phase of iron ores can be predicted through the experiment verification.

Jan 1, 2015

By Tracy Brettmann

The Highway 146 Bridge Expansion Project across the Clear Creek Channel in Houston, Texas was designed on driven precast concrete piles. However, during construction, the piles along one side of the bridge along the main channel encountered obstructions and couldn’t be installed. These obstructions turned out to be the remnants of a previous bridge foundation at this location, which was unknown to the designers since that bridge had been demolished 40 years ago. Those old foundations were massive 20 ft by 40 ft (6 m by 12 m) pile caps 11 ft (3.3 m) thick supported on precast concrete piles 37 to 55 ft (11 to 17 m) long. The foundation re-design for these locations involved installing a single 78 inch (2 m) diameter drilled shaft up to 125 ft (38 m) long to replace the originally planned driven pile supported pile cap. The drilled shafts would need to be installed within very tight tolerances since they were supporting a single bridge column directly above it. In addition to drilling through the obstructions, this work would need to be completed from barges in 30 ft (9 m) of water capable of dealing with both the current and tides affecting this area. The shafts were installed using a multi-step process. The first step involved coring a larger diameter 100 inch (2.5 m) hole through the reinforced concrete pile cap and removing the concrete inside. This was followed by the installation of a 72 ft (22 m) long permanent casing to and removing the soil and existing precast piles inside. Finally, the drilled shaft excavations were advanced to the completion depths (uncased) using bentonite slurry as the support fluid.

May 1, 2022

By E Mutaz, M Bahaaddini, D J. Williams, M Serati

The contribution of the mining industry to the global economy has reached (and gone beyond) $1,800 billion in recent years that necessitates (more than before) the need to ensure workability, viability, health, and safety of mine sites and workers to meet the ever-increasing global demand for mineral resources. Amongst the many challenges facing the excavation industries, rockburst and spalling failures in deep mines in hard and brittle rock formations are yet happening that are still deemed as unsolved problems. During unconfined compressive testing of brittle rocks, microcracks initiate at approximately 0.3–0.5 of the peak strength (which is commonly known as the Crack Initiation stress level) mainly in the direction of the major principal stress, then grow unstably and coalesce to form macro fractures at approximately 0.7–0.8 of the peak load at a so-called Crack Damage stress threshold. From a stress-strain perspective, the crack damage stress threshold () is associated with the reversal point of the volumetric strain, which is also proved to be strongly affected by the intermediate principal stress. This paper extends the previous studies on the impact of true triaxial loading conditions on the CD stress level in high porosity rocks, and introduce a new Crack Mode-Changing Stress (CMCS) defined as the minimum principal stress required to change rock fracturing from splitting to a sliding failure mode. A large number of experiments on sandstone specimens were carried out at different true triaxial loading conditions and the effect of principal stresses on the CI and CD as well as CMCS were studied. The results show that not only the intermediate principal stress, but also the minor principal stress can significantly affect the CD and CMCS thresholds.

Apr 26, 2022

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By Chris Normand, Paul Volpe, Eric Wey, Howard Perko, Burt Ogilvie, Patrick Murray

"A refinery expansion project for Marathon Petroleum Company in Southern Louisiana required existing medium to large pipe racks to be expanded for additional capacity. Foundation modifications were necessary in order to add levels to the existing pipe racks. New piles were added and existing pile cap foundations were expanded. Several different pile types were considered. Custom designed large diameter helical piles were chosen, because they can be installed quickly with low overhead restrictions, produce minimal soil spoils, and are cost effective. The load capacity required for piles was higher than typical, off-the-shelf helical piles. In particular, the lateral load capacity demand was high due to wind loads of a hurricane prone region. Methods used to design and size helical piles are summarized including capacity to torque ratio estimation for composite helical piles. Pile load testing was performed in order to confirm design capacities of the helical piles under axial and lateral loading. Measured axial and lateral deflections compared well with predicted values. This case history evaluates the effectiveness of modern helical pile design methods within the context of a real and practical example.INTRODUCTIONAs the capacity of modern installation equipment increases, large-diameter helical piles are being used to support higher loads in more diverse applications. Currently, large-diameter high-capacity helical piles are used for electrical power transmission, power generation, high-rise buildings, bridges, and industrial applications. This case study regards a 2.5-mile pipe rack modification project within an existing refinery. One of the many challenges for engineering and construction of refinery revamp projects is determining how to effectively expand the capacity of existing foundations for additional equipment, piping, and other facilities. Custom designed large-diameter helical piles provided an effective solution to the challenges faced when expanding the capacity of existing pipe racks."

Jan 1, 2017

By R Forster

Direct ship iron ore (DSO) operations at Extension Hill in Western Australia’s Midwest region have commenced, with fi rst product railed to the port of Geraldton in July 2011. Reserves are 14.8 million tonnes (Mt) of haematite-goethite ore overlying an Archaean BIF-hosted larger magnetite deposit which Mount Gibson Iron Limited (MGI) sold to other parties in 2006.Some unique geological aspects of the deposit shape DSO mining and processing operations. Owner-operator selective mining, blending, crushing and screening on site will produce three million tonnes per year (Mt/a) of Lump and Fines product to be trucked 86 km to Perenjori, railed 232 km to Geraldton, and loaded aboard Panamax-sized ships through the dedicated iron ore shiploader at the Geraldton Port Authority’s Berth 5 facility.The statutory approvals process for this project formally began in 2004, dominating delays in a predevelopment phase which extended over a longer period than the likely life of DSO operations. The lack of transparency, uncertainties and costs inherent in state government processes have influenced decisions made by MGI while assessing other development opportunities in Western Australia. Potential for additional Reserves exists at Extension Hill, however MGI’s ability to extend the mine life will hinge on statutory approval to explore for and evaluate other DSO resources on surrounding granted mining leases.The nature of the resource and use of existing infrastructure for product transport have enabled MGI to keep operating costs and capital intensity of this project relatively low. A tenacious development approach by MGI and robust project economics have fi nally enabled this site to take its place as a revenue earner beside the company’s other DSO operations at Tallering Peak and Koolan Island.

Jul 11, 2011

By F Kock, Y Sulianto, T Trott, B G. Putland, D Morgan

"Northparkes installed and commissioned a secondary crushing circuit in 2010 to debottleneck the semi-autogenous grinding (SAG) mill constrained grinding circuits. Following further improvements to the circuit (inclusion of a double deck vibrating screen), the project successfully delivered finer feed to the SAG mill. The result of this project was an increase in the milled tonnes from 5.6 Mt/a in 2012 to 6.0 Mt/a in 2013.The increased throughput rates introduced new challenges with the circuit becoming power limited. How to best optimise the available comminution power, while delivering the optimal particle size to the flotation circuit was made the key optimisation objective. To achieve this objective, Northparkes initiated a project that included engaging comminution experts. Recommendations included changes to the SAG mill including mill lifter design, increased grinding media charge levels and reduced grinding media size with aim of producing a finer grind size.Northparkes implemented these recommendations along with some other changes to SAG discharge grates and the mill discharge vibrating screen. This achieved a substantial reduction in the flotation feed particle size distribution (approximately 20 microns) by utilising increased average SAG power utilisation, in turn resulting in a two per cent increase in copper recovery.With power utilisation now maximised, the next phase of optimisation has moved to the throughput-grind-recovery relationship and the cost benefit analysis of installing additional grinding power.Citation:Sulianto, Y, Trott, T, Morgan, D, Bell, T, Kock, F and Putland, B, 2016. Optimisation of Installed Mill Power Post-installation of Secondary Crushing Circuit at Northparkes Mines, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 331&ndash;338 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J. G. Kim, B. G. Chae, D. S. Cheon, E. S. Park

The underground structures such as high-level radioactive waste disposal thermal energy storage should be designed and constructed considering thermal-mechanical characterization because of long term and/or cyclic thermal stress. High temperature changes in these structures can extend the existing cracks and generate new cracks in surrounding rock mass. In case of long term and/or cyclic thermal stress conditions, it is possible to lose the function of structures caused by the significant cracks and fracture growth in the rock mass. In this study, the critical thermal crack temperature of the granite, limestone and thermal Kaiser effect were evaluated. Experiments were carried out with the heating speed of 1.5?/min. To avoid thermal shock and target temperatures were set at 150? and 250?. In order to verify the thermal Kaiser effect, the samples were heated by 150 ? after 2-3 repetition to 250?. The generation and growth of cracks were observed through an acoustic emission measuring system. The variation of the physical rock properties was measured before and after thermal experiments. After compared with the thermal experiments using PFC2D, numerical simulations were carried out at higher temperatures (400?). The experiments showed that the initial thermal crack temperature of granite and limestone is about 35?, 32? and the critical thermal crack temperature were about 69? , and 49? , respectively. The experiments confirmed the thermal Kaiser effect of experimented granite and limestone due to thermal cyclic loading. From the numerical analysis, the critical crack temperature showed the same tendency as the thermal experiments. The P and S wave velocity of the sample after the experiment were reduced. Therefore, when heat is applied in long-term and repetitive conditions, these cracks may affect the function and stability of the underground structure. Therefore, further studies of thermal stress effects should be performed.

Jan 1, 2015

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By E Villaescusa, A Kusui, R Talebi, R Hassell, C Arcaro

Northern Star Resources (NSR) operates several seismically active mines as part of its Kalgoorlie Operations. In order to successfully continue mining at depth in increasing stress conditions, strategies need to be developed to reduce, control and manage the impact of seismicity causing damage to the rock mass. Consequently, a research partnership was developed with the WA School of Mines (WASM) through Mining3. The main aim of the project was to develop appropriate ground support standards that could withstand the expected dynamic response with minimal to no rehabilitation required for the life of that excavation. The project utilised a design methodology for determining the required energy demand based on detailed geotechnical mapping, probabilistic analysis of wedge formation and an estimate of rock ejection velocity based on uniaxial compressive strength of the intact rock (Villaescusa et al. 2016). The ground support scheme consists of high tensile chain link mesh, resin encapsulated de-coupled posimix bolts and plain strand cable bolts, in one, or multiple passes together with plain shotcrete. Implementation of the design posed several challenges including how to install the chain link mesh, maintaining the required productivity, ensuring quality control, and understanding the interaction of the several ground support components within the scheme. The implementation of the system within a trial area was successful from development mining to open stope extraction. The most significant field verification of the system occurred with near field M+1.9 seismic occurring in proximity to an operating long-hole drill. Despite large displacements exceeding 0.5m in places, there was no significant ejection of rock or failure of the ground support system. Following the successful trial, the ground support design methodology and standards have been implemented across several NSR sites. The system forms the basis for the successful extraction of resources in future high seismic risk areas.

Mar 15, 2021

By W M. Tekano, T S. Coulter, N M. Hutt

The Vancouver Island Highway Project (VIHP) was a $CAD 1.2 billion expenditure by the Province of British Columbia to improve travel safety and relieve traffic congestion between Victoria and Campbell River on Vancouver Island. In the section of highway between the Tsolum River and Oyster River, on the Inland Island Highway portion of the VIHP, over half of the rock to be cut and filled was found to be net acid generating. The Tsolum River has been impacted by metal leaching and acid rock drainage (ML/ARD) for decades from an upstream closed minesite. Geochemical testwork indicated: over half of the rock along this section of highway was potentially net acid generating based on a site-specific SNPR (=NP/SAP) criterion of 1.5; some core samples were already acidic; pyrite occurred in disseminated framboidal and gel forms; the rate of acid generation was not high; measured neutralisation potential (NP) provided some lag time for the onset of net acidity; and non-carbonate neutralising minerals prevented low pH (These predictions led to ML/ARD controls involving: realignment of the highway; elevation control to minimise the volume of disturbed rock; encapsulation of blasted-rock fills within the highway, surrounded by low-permeability till and covered with asphalt; and diversion of water away from cut faces. Internal pipes drained any water reaching the fills into external ditches and ponds, where the water could be monitored and, if necessary, treated. Water from the cuts was also captured in ditches and carried to monitored ponds. Elevated aqueous sulfate concentrations in several ponds confirmed that sulfide minerals were oxidising, but the lack of both acidic pH and increasing trends in concentrations demonstrated that ML/ARD was controlled. Contingency plans for any pond that may become acidic include water treatment, which predictive testwork has shown would not require substantial amounts of limestone or lime.

Jan 1, 2003

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016

By H Kurth, L Balzan

The potential for bulk diversion was identified and quickly implemented following the development of bulk sensing technologies applied to conveyed flows. In the early 1980s real time analysis of ash in coal was intended to improve the understanding and control of quality variability. By the end of the 1980s approximately 5% of coal analysers installed were being utilised for bulk sorting; diverting flows to create stockpiles to improve blending flexibility and boiler feed consistency, diverting waste material, or bypassing the beneficiation process when the coal met product quality criteria. In the 1990s bulk sensing and sorting utilising natural gamma detection was applied to conveyed waste in gold-uranium mineralisation and allowed ore to be recovered and processed that would otherwise have been discarded. Further applications developed in the iron ore sector where product quality ore could be diverted to bypass beneficiation and save significant unnecessary processing costs and improve recovery by avoiding process inefficiency losses. Plant capacity was freed up to be utilised by material that required processing. Similar benefits became evident in the phosphate industry and in base metals where multi-elemental analysis using Prompt Gamma Neutron Activation Analysis provides ideal opportunities to representatively measure 30 second conveyed increments at high accuracies. This has been successfully adopted in copper, nickel, platinum and lead-zinc to improve waste removal after primary crushing to eliminate unnecessary expense and improve plant efficiency. The benefits include increased output from existing operating capacity, significant reductions in consumable costs and generation of fewer detrimental waste streams. The paper outlines the technologies and discusses case studies covering the above commodities, demonstrating the immense value that representative real time measurement of conveyed flows can create. Measurement data concurrently provides multiple benefits in operational performance besides sorting, through ore reconciliation, ore blending, feedforward control and metal accounting, adding further value.

Nov 10, 2020

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By Jorge Cardenas, Diego Sanchez

Maximizing SAG mill throughput and metallurgical recovery in hard rock operations requires achieving target fragmentation, particularly a sufficient proportion of fines (<25.4 mm). These fines thresholds are strongly influenced by rock mass competency, commonly characterized using the Axb parameter (30–70) from the JK Drop Weight Test. In many operations, conventional blasting designs and standard emulsions fail to generate the fines content required for efficient downstream comminution. This study evaluates several advanced blasting strategies aimed at enhancing fines generation in very competent rock masses while maintaining cost-effective drill and blast performance. The first approach focuses on steadily increasing the powder factor (kg/t) as a core strategy, complemented by adjustments in blasthole diameter, reduced burden and spacing, the use of dual initiation points, short inter-hole delays (<25 ms), and optimized sequencing—all aimed at enhancing energy distribution and maximizing fines generation in highly competent rock masses. The second strategy consists of increasing the energy factor (kJ/t) by selecting explosives with higher energetic content and detonation performance. This includes the use of heavy ANFO blends and ultra high-energy emulsions with aluminum-based formulations, achieving Relative Bulk Strength (RBS) values between 180–190 and up to 210–230, respectively. These products offer higher detonation velocity (VOD) and peak pressure, enhancing shock energy transmission and breakage efficiency. Field results in granodioritic porphyries with high uniaxial compressive strength showed a 3–5% increase in fines generation compared to standard emulsions—contributing directly to meeting mill performance targets in high Axb conditions. Combined, these strategies provide a practical and technically validated pathway to achieving fines generation targets required for optimal mill performance. When matched to site-specific rock mass characteristics and integrated with blast monitoring tools, they enable improved fragmentation control, reduced P80, and enhanced plant throughput—without compromising operational efficiency or increasing costs disproportionately

Jan 26, 2026

By Brian Gettinger, Jared Barber, Richard Weatherly, Shannon Dunne, Jeff Masek, Chuck Wolf, Fazle Rabbi, Jack Canfield

During Hurricane Harvey over 60% of the 39 WWTPs, including the low-lying 25 MGD Sims North WWTP, and one third of the 382 lift stations owned and operated by the City of Houston were flooded resulting in extensive facility damage, loss of service and uncontrolled release of untreated wastewater into bayous and creeks. In response, the City has embarked on an effort to improve system resiliency by consolidating at-risk facilities with a network of deep sewer tunnels. These tunnels will provide secondary benefits to the collection system of augmenting the capacity of the existing 6,000 miles of sewer mains and lowering the collection system profile in poor performing areas. Investigations on the cost to mitigate the flood damages by raising the liquid stream processes at the Sims North WWTP is estimated at nearly $450 million. Instead of spending $450 million to raise the plant, the funds will be directed to providing a more robust and resilient wastewater system for the Sims basin area of Houston. The backbone of this new system is a 4.5-mile-long, 110 inch diameter deep gravity sewer tunnel that will convert a system heavily reliant on distributed lift stations to a majority gravity system with a deep consolidated lift station at the Sims South WWTP. This will also allow the City to address the flood prone infrastructure at Sims North and consolidate its operations into a single permitted outfall for this collection system. This approach is the outcome of a team effort focused on maximizing system resiliency and sustainability for the next 100 years. By thinking outside the box, the City of Houston will not only mitigate the flooding risk at Sims North WWTP, but also solve regulatory and operational challenges throughout the sewershed and deliver a winwin on multiple levels.

Jun 13, 2021