Search Documents

By Richard Schellinger, Ronald H. Carlson, Robert D. Norris

INTRODUCTION A very important key to the success of an in-situ leach venture is proper choice of well field chemistry, in which type and concentration of oxidant plays a significant role. For proper design of well field and plant, an engineer must be able to estimate uranium production levels and their change with time. The rate controlling step in the uranium leach process is generally acknowledged to be the oxidation step (Goddard and Brosnahan, 1980; McKnight and Anthony, 1979; Mays, 1979). Uranium head grade is very dependent upon concentration of oxidant injected into the ore zone. If oxidant levels are too low, uranium production requirements will not be met; if levels ate too high, excess oxidant will be wasted in side reactions with gangue material and leach economics will suffer. To date, no reliable laboratory technique exists for generating data easily translatable to field conditions. Empirical correlations based upon lengthy field testing have been the major tools avail- able to the design engineer to date. During the past five years, FMC has developed lab- oratory techniques for studying uranium leach chemistry under conditions simulating as closely as possible the field situation. Both agitated batch and consolidated core leach procedures have been developed. Results of FMC agitated batch studies are described in detail in a companion paper (Carlson, et. al., 1980). This paper will focus on the technique developed for leaching consolidated undisturbed core under simulated down-hole conditions. Through use of a follow-up computer model (Winkley, 1980), generated data can be translated to expected field response, thus providing the design engineer with valuable information in a relatively short period of time. CHEMISTRY In addition to uranium (+4), other oxidant-consuming species present in uranium ore are iron sulfides and carbonaceous material. Iron sulfides are usually present in concentrations far exceeding those of the other two materials and, therefore, represent the major oxidant-consuming species present in uranium sandstone ore. Previous studies (Carlson, et. al., 1980) have shown that iron sulfides exist in both Texas and Wyoming ores as a mixture of pyrite and marcasite (FeSz); furthermore, uranium mineralization (existing as uraninite) was shown to exist as a fine granular material coating or imbedded in iron sulfide crystals and sand grains (i.e. quartz and feldspars). The leach chemistry of a uranium ore body can be described by the following equations using hydrogen peroxide (Hz021 as oxidant:

Jan 1, 1980

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Eugene McAuliffe

It is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the '(do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co, has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as i'extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment, can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. Safety work in some form has been carried on in and about the mining properties of The Union Pacific Coal Co. since the first mine was opened at the now long-abandoned town of Carbon, Wyo., in 1868. On June 30, 1903, an explosion and subsequent mine fire occurred in mine No. 1 at Hanna, taking 169 lives, and a second explosion occurred in the same mine on March 28, 1908, in which 59 additional lives were lost. Looking back with impartiality on the causes leading up to these two unfortunate disasters, we can only conclude that shooting from the solid, the absence of adequate ventilation, rock dusting, the use of water at the face to allay

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By W. F. Hergert, L. H. Banning

Experimental production of Al-Si alloys, containing from 33 to 55 pct Al, by direct reduction of aluminum silicates in a three-phase arc furnace is described. Advantages of a smelting technique utilizing hogged wood waste as part of the reductant and for temperature control are discussed. WORK on the problem of producing aluminum by smelting has been in progress since the middle of the eighteenth century. Early work met with little success and in 1782 Lavoisier, an eminent French chemist, expressed the belief that alumina could not be reduced by carbon. It was almost a century later when the Cowles brothers developed a process for the production of aluminum alloys by reducing alumina coincident with the reduction of other metal oxides. In practice, the other metal oxide was usually copper. In 1907 it was first shown that alumina alone could be reduced by carbon at a temperature of 2200°C. The metal produced was volatilized and lost or recombined with the oxides of carbon formed in the reaction.' For a number of years after the Cowles brothers abandoned production of Cu-A1 alloys because their product was not commercially competitive with the aluminum produced by the Hall process, there was little interest in thermal reduction processes. After World War I interest in such processes was renewed and a number of patents were issued on processes for the production of A1-Si alloys.' , "he function of the silicon in these processes was the same as the function of the copper in the Cowles brothers process, namely, to prevent the reduced aluminum from recombining with the oxides of carbon and to promote absorption of the aluminum vapors set free at the high temperature required for the reduction reaction. The advantage of using silicon in place of copper for this function is that silicon has a higher boiling point (2600"C) than copper (2310"C) and its oxides, combined with aluminum oxides, occur in nature in almost unlimited quantities. No A1-Si alloys have been produced commercially in the United States, as far as is known. However, considerable experimental smelting of aluminum silicate materials has been done by the TVA at Wilson Dam, Ala.' The most extensive development and commercialization of the electrothermal production of A1-Si alloys took place in Germany before and during World War II.V he furnaces used in the

Jan 1, 1956

By Eugene McAuliffe

It is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the '(do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co, has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as i'extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment, can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. Safety work in some form has been carried on in and about the mining properties of The Union Pacific Coal Co. since the first mine was opened at the now long-abandoned town of Carbon, Wyo., in 1868. On June 30, 1903, an explosion and subsequent mine fire occurred in mine No. 1 at Hanna, taking 169 lives, and a second explosion occurred in the same mine on March 28, 1908, in which 59 additional lives were lost. Looking back with impartiality on the causes leading up to these two unfortunate disasters, we can only conclude that shooting from the solid, the absence of adequate ventilation, rock dusting, the use of water at the face to allay

Jan 1, 1938

By R. Raring, W. J. Harris, J. A. Rinebolt

The effects of additions of alloying elements on the true-stress, true-strain characteristics of 0.30 pct C, 1.00 pct Mn, 0.30 pct Si pearlitic steel were studied. The alloying elements investigated were C, Mn, Si, P, The alloys are compared on the basis of fracture stress, fracture strain, energy to fracture, rate of strain hardening, strain hardening exponent, height of the flow curve, and lower yield point. IN the past, nearly all studies of the effects of alloying elements on the tensile properties of metals have compared the conventional engineering parameters, namely, tensile strength, yield strength, elongation, and reduction of area. Recently, however, the true-stress, true-strain method of recording results from the tension test has been used; Lacy and Gensamer,' Hollomon," and French and Hibbard- are used this method to study the effects of composition on strength and ductility of metals. In this paper, the effects of certain alloying elements on true-stress, true-strain curves of steels with nearly constant grain size and pearlite spacing are presented. The notation employed in this paper is given in Table I. Since the definitions of stress and strain and the analytical geometry of the stress-strain curve have been explained previously, for example by Gensamer,' they will not be reviewed here. However, the method used for the determination of energy to fracture, E,, requires mention. These energy values were calculated on the assumption that the flow curve followed the idealized equation:' corresponds to the specific energy absorption to that strain value. There is justification for preferring the use of eq 1 for the determination of the energy to a particular strain rather than the area under the experimental stress-strain curve, since Gensamer showed that the use of the Bridgman correctione for stress at the neck of a tensile specimen brought the corrected experimental curve nearer to the idealized power-law curve than to the uncorrected experimental curve. However, it should be noted that the difference between the areas under the idealized curve and the experimental curve is not great for strain of less than 1.0, as can be seen from Fig. 1. In this figure, the true-stress, true-strain curve for a 0.01 pct C, 1.00 pct Mn steel is plotted through the experimental data points. From the value of a,, from this curve and the value of n as determined by the Inm-

Jan 1, 1952

The following is a report of the papers submitted to the Papers 'and Publications Committee during 1928: The Committee held nine regular meetings during the year 1928. During that period there were presented to the Institute 214 papers which were acted upon as follows: Accepted as Technical Pub1ications............................ 85 Declined for publication...................................... 16 Action pending, Dec. 31...................................... 25 Manuscripts held for annual volumes, Dec. 31................... 7 Withdrawn temporarily...................................... 1 Accepted as Preprints........................................ 20 Printed for first time in volumes.............................. 35 Published in Mining and Metallurgy........................ 12 Papers in Technical Publication No. 156 (Coal Classification) and not accounted for elsewhere in this table..................... 10 Mimeographed only*................................... 3 Total.................................................. 214 * A considerable number of papers were mimeographed for the annual meeting. Of the 85 papers accepted as Technical Publications 8 were reprinted in the Transactions, 7 in Proceedings of the Institute of Metals Division (1928), 7 in Iron and Steel Technology in 1928, 13 in Geophysical Prospecting, and 50 were in Technical Publication form on Dec. 31. Of the 20 papers accepted as Preprints 1 was reprinted in the Transactions, 13 in Petroleum Development and Technology in 1927, 2 in Geophysical Prospecting, and 4 were in Preprint form on Dec. 31. Of the 35 papers printed for the first time in the various volumes 8 were included in the Transactions, 2 in Proceedings of the Institute of Metals Division (1928), 1 in Iron and Steel Technology in 1928, and 24 in Petroleum Development and Technology in 1927. Of the 12 papers accepted for Mining and Metallurgy 1 was, accepted for Geophysical Prospecting and 1 for the Transactions. There were published in 1928 113 Technical Publications containing a total of 1928 pages, as against 88 in 1927, totaling 1528 pages. The Technical Publications published in 1928 were classified as follows: Group A, Metal Mining, 17 papers (361 pages); B, Milling and Concentration, 4 papers (39 pages); C, Iron and Steel, 15 papers (256 pages); D, Non-ferrous Metallurgy, 13 papers (191 pages); E, Institute of Metals, 36 papers (588 pages); F, Coal and Coke, 15 papers (392 pages); G, Petroleum and Gas, 10 papers (246 pages); H, Non-metallic Minerals, 3 papers (33 pages); I, Mining Geology, 18 papers (356 pages); K, Mining Administration, etc., 3 papers (47 pages); L, Geophysical Prospecting, 21 papers (430 pages).

Jan 1, 1929

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By C. M. Kleeman

All mines have a finite life and the time comes when the ore is depleted, or it has become uneconomical, or for some other reason which may be peculiar to that particular mine, it must be shut down. The operation at that point of time still has some assets such as mining and milling equipment, workshops, and in the case of a gold mine, an unknown quantity of gold which has been trapped in the treatment plant. Recovering this gold can be done at small cost and can be extremely profitable. Recovery of these hidden assets requires a good knowledge of the treatment plant, i. e. , as say values of heads, tails, and of the products produced; and if mercury for amalgamation was used, where? A careful study of available plant records can be extremely valuable in forming a working plan for adequate recovery. In the following paragraphs the various unit operations and equipment where gold can collect are described and suggestions made for its recovery. Subsequently, a case history will be given for dismantling a gold plant which had a complex flowsheet and which had been in operation for many years. Looking for trapped gold in a crushing section would invariably not be worthwhile since crushing is normally a dry process and there would be few areas where free gold could collect. In the milling section, however, many areas can literally become small gold mines in themselves. Material in the bottoms of grinding mill scoop boxes can be high-grade, and even the scale on the sides of the boxes should be scraped off and collected. Mill liners should be removed and all scale, rust, and residue collected. Residue in the bottoms of rake or spiral classifiers, if they have been used, should be removed as should the scale and rust on the sides of pump sumps, launders, etc. The following procedures should be used to extract gold from these collected materials. All steel (ball scats) should be removed, screened out, and reserved. Fine material should be placed in an amalgam barrel, water added and ground with the amalgamation tailings being sampled and assayed. If high-grade, tails should be reserved; if not, discarded. The coarse material that was screened out should be placed in a heap, regularly sprayed with water and allowed to rust. After several months this material should be screened again and the fines amalgamated.

Jan 1, 1981

By Hal Palmer

A number of Articles contained in the United Nations Convention on the Law of the Sea III (UNCLOS) bear directly on legal issues related to the recovery of mineral deposits on the ocean floor. Mineral resources of the continental margin other than oil, gas and hydrates include, sand, gravel, shell, coral, gemstones and phosphorite. Jurisdiction over the exploration and exploitation of these deposits is determined either by the Territorial Sea claims of a coastal state or their recognized sovereign rights in the Exclusive Economic Zone (EEZ). At least 33 coastal states have the right under Article 76 (Continental Shelf regime) to claim seabed jurisdiction beyond 200 nautical miles (EEZ limit). In addition, several states have "Pioneer Investor" status with regard to seabed resources in international waters (The Area). A global maritime boundary database (GMBD) has been developed as a basic resource identifying the current claims of coastal states. It provides detailed information on existing boundaries and limits determined by the UNCLOS accords or by multi-lateral agreements which affect mineral exploration and exploitation. This paper will describe the GMBD and its construction and maintenance.

Jan 1, 2000

By E. C. Nelson

An equation is derived for calculating approximately the solubility of nitrogen in an alloy steel over a temperature range from 1200" to 1900°C using data on the effects of alloys on the activity coefficient of nitrogen in iron at 1600°C. Calculated values are compared with experimental data. STUDIES involving the solubility of nitrogen in complex iron alloys have been aided by a system devised by Lanenberg for calculating the solubility of nitrogen in ternary and higher alloys of iron at 1600C using available data on the activity coefficient of nitrogen in binary alloys. Calculated nitrogen solubilities agree well with experimental determinations on complex alloys,' and the calculation procedure is useful when experimental data on specific alloys are not required. A method for extending calculations of nitrogen solubilities in alloy steels to temperatures other than 1600°C would be useful because of the paucity of experimental data in this area. Assumptions which must be made to permit this calculation introduce an element of approximation; however, the calculation is useful in cases where a large number of alloys and temperatures are under consideration, and the precision of experimental measurements is not required. The activity coefficient can be freed from the isothermal restriction of Langenberg's calculation if it is assumed that the solution is "regular". This is a reasonably good assumption for solutions of nitrogen in iron alloys, because usually they are dilute and the heat of solution is relatively small. The presence of large amounts of certain alloying elements would make this assumption less tenable.3 One of the properties of a regular solution is: when "f" is the activity coefficient of a solute and "T" is the temperature in OK. If the activity coefficients at temperatures T and T2 are denoted by subscripts 1 and 2 respectively: The activity coefficient of nitrogen in a complex alloy then can be calculated at any temperature from the sum of the effects of the other solutes on the activity coefficient of nitrogen at 1600°C. It will be convenient to incorporate this expression into an equation which will give directly the logarithm of the solubility of nitrogen at any temperature in the presence of alloys. Two constants, the solubility of nitrogen in pure iron at 1600 "C and the partial molar heat of solution of nitrogen in iron are required. The heat of solution value of 1400 cal at 1600 °C quoted by Kubaschewski and vans will be used. The accuracy of the calculation will suffer if the heat of solution should change materially with temperature. In the absence of experimental data on the temperature dependence of this quantity, it will be expedient to restrict the application of the calcula-

Jan 1, 1963

By E. Wroth, D. G. Krige

Written contribution E. Wroth* (Visitor): The technical aspects of the assistance scheme which IS provided for in the Gold Mines Assistance Act, 1968, and certain consequential amendments to the Income Tax Act, 1962, are explained by Dr Krige. The object of this contribution is to explain the working of the Gold Mines Assistance Act (hereafter referred to as the 'Assistance Act') for the benefit of those concerned with the tax and assistance assessments of gold mining companies. The views expressed do not necessarily reflect the Revenue Department's interpretation of the legal provisions involved. 1. MINES WHICH QUALIFY FOR ASSISTANCE 1.1 The assistance scheme is applied on a selective basis. Mines which qualify for assistance are defined in the Assistance Act as 'assisted gold mines'. The requirements for classification as an assisted gold mine are that: (i) the mine be a producing gold mine; (ii) it would be likely to close down within eight years if not assisted; and (iii) with State assistance its life would be appreciably prolonged and there would be a significant increase in production of gold or uranium, or of both gold and uranium. 1.2 A mine is only considered for classification as an assisted gold mine on application. Such applications must be made to the Mining Leases Board through the Government Mining Engineer. Classification of a mine as an assisted gold mine is at the discretion of the Minister of Mines who acts in consultation with the Minister of Finance and has regard to the recommendations of the Mining Leases Board. 1.3 The Minister of Mines will impose conditions subject to which a mine is to be classified as an assisted gold mine. The most important will be that the mine must immediately lower its operating pay limit, as normally calculated, by a percentage fixed by the Mining Leases Board and conduct its future mining operations in accordance with the average grade of its ore reserves determined on the basis of such lower pay limit. l.4 The Minister will fix the date as from which classification as an assisted gold mine is to be effective. So long as the mine has operated on the basis of the lowered pay limit for at least three months during the particular year of assessment, he would normally fix the effective date as the first day of the year of assessment.

Jan 5, 1968

Pictured on these pages are the six RMCMI Scholarship Award Winners for the 1985-86 year followed by a brief profile. Five of the winners were present as RMCMI guests at the June convention at Tamarron to receive their recognition plaques at the welcoming session held Monday, July I, 1985. In addition to the plaques, each winner will receive $500.00 to be used toward tuition in the coming academic year. Also, as this is a continuing award, the winners from the 1984-85 season, will also receive an additional $500.00 for tuition use in their senior years provided they have maintained a good academic standing. Criteria for these awards is (1) 'That the award be made in the spring to a sophomore student to be used toward tuition during the junior year. (2) That the recipient be both a U. S. citizen and a resident of the state involved. (3) That the recipient have good academic standing, be pursuing a degree in a mining related field and have an expressed interest in Western coal as a possible career path. Contributions to this worthy project are tax deductible to each individual RMCMI member as well as firms, businesses and corporations. Checks payable to RMCMI Scholarship may be mailed to the RMCMI Office at 777 Nile Street in Golden, CO 80401. Profiles of the 1985 winners follow: [ ]BEVERLY MOON Colorado School of Mines Beverly is a resident of Greeley, Colorado. She maintains a 3.1 grade average at the Colorado School of Mines and was on the Dean's List in 1983. In addition she also appeared on the Academic Roll in 198 1 and 1984. She participates in the Society of Women Engineers, and this summer Beverly is working for North American Coal Corporation's Coteau Properties, outside of Beulah, North Dakota, as an Engineer's Assistant. [ ]DEE BRAY Montana College of Science and Technology Dee comes from a small ranch outside of Hall, Montana and is currently pursuing a degree in Mining Engineering at Montana Tech. This summer he is working for North American Coal where he was selected out of more than a dozen applicants for his position. As a side note, Dee's brother, Dean Bray, is also a Mining Engineer, a Montana Tech Grad, and works for Consol at the Glen Harold Mine in North Dakota.

Jan 1, 1985

Your esteemed favors transmitting my discharge as your representative on the War Minerals Committee have come duly to hand and the kind words of commendation contained are greatly appreciated. Like other war committees, The War Minerals Committee's business in Washington was to meet an emergency as best it could, and as soon as the emergency had passed pressure of personal responsibilities immediately scattered the individual members. A detailed report of the Committee's work is therefore impossible. But before the matter is closed I feel it incumbent on me to ask you to report to the Directors and the Council, and through them to the members of the Institute and of the Society, the inestimable value to our Committee of the unstinted support given by both your officers and members. The instant response to all requests for funds was of the greatest assistance in getting started with office force, stationery, etc., and led later to a regular organization in the Bureau of Mines, working under a special appropriation, which is still doing good work as the War Minerals Investigation under Dr. Spurr. The voluntary work of the special sulphur and manganese committees formed by the War Minerals Committee was of great value to the Government. Copies of private reports supplied were of much assistance. But the great service of engineers and geologists as a whole was rendered in connection with the passage of the War Minerals Bill by Congress. Though every assistance possible was rendered by the Bureau of Mines and the Geological Survey, by the close of 1917 our Committee had about reached the limit of its usefulness in the way of stimulating the various Government executive committees, bureaus and departments to a realization of the country's need of preparation for domestic production of "war minerals" and had found that special Congressional action was imperative if the war was to continue for anything like the time then generally feared. This was necessary not only 'to insure a. supply of war minerals but to make possible the appointment of some able mining administrator of large experience in the mineral industry who, with ample authority, could sit in the councils of the Government and see to it that the ever increasing autocratic powers the war was developing were used toward the mining industry so as to foster rather than crush the latter in its effort to produce sufficient raw material for war and essential civil requirements.

Jan 7, 1919

By A. L. Holley

Those who are familiar with working gas furnaces will perhaps admit that the ordinary producer is the least satisfactory feature of the- whole system, chiefly by reason of its great waste of fuel, both above and below the fire. The waste of fuel in cleaning the fire has not, as fdr as I am aware, been carefully measured ; it has been roughly estimated at various works as averaging twenty per cent. to twenty-five per cent. The coke that falls into the ash-pit is largely mixed, if not stuck together with clinker; when this coke is not recovered and utilized (and where coal is cheap it does not pay to recover it), the waste is certainly as high as above estimated. Cleaning a fire on a grate (especially a fire of dirty coal, like much of our Western coal), by inserting a few temporary grate-bars, then withdrawing the regular grate-bars and letting the whole lower part of the fire tumble into the ash-pit, must necessarily be wasteful of fuel, but it has been found to be the most practical system. The fire under a boiler should be thin, to insure perfect combustion; hence it may be moved from one side to the other, so that .the clinker and ashes may be uncovered and removed. But a producer fire should be so thick that carbonic oxide only shall rise from it; a thick fire cannot be thus manipulated. In several of the French works the ordinary producer without grates is employed ; the whole body of the fire rests on the floor of the ash-pit. It did not seem to me that less fuel was wasted here than with grates in cleaning fires. The bottom layer of the fire had to be drawn out with hooks, and there was nothing to prevent much coke from coming away with the clinker and ash. A producer shaped like a cupola furnace has many advantages, but if grates are employed the waste of coke in cleaning is not lessened. But the waste at the bottom of the fire is only a part of the waste in the ordinary producer. Mr. Emmerton, chemist to the Juliet Iron and Steel Company, has lately made a number of gas analyses from the producers of that company, worked with impure Illinois

Jan 1, 1880

By Stephen H. Stow

A relationship exists between the color and the chemical composition of the pebbles from the Bone Valley Phosphate Formation. Darker-colored pebbles are relatively high in iron oxide and relatively low in calcium phosphate when compared to lighter-colored samples; the brown color of the phosphate pebbles can be correlated with their iron content and the black and gray colors with their organic carbon content.1,3 It was anticipated that the darkness of a phosphate sample might be quantitatively measured by a simple reflectivity test and that the amount of reflected light could be correlated with the chemical composition of the rock, especially with the elements which cause the color and darkness of the Florida phosphates. Twenty-one samples of production grade phosphate rock from Hillsboro County, Fla., were studied. All samples were ground to -200 mesh for reflectivity tests and analyses. All analyses are accurate to well within ±2% of the reported value, except for aluminum and organic carbon, which are accurate to only ±15% of the reported amount. Reflectivity measurements were taken with a model 610 Photovoltmeter for tri-stimulus amber, blue and green, and white lights. Experimental procedures and data are available upon request. Results Table 1 contains linear correlation coefficients (LCC) for the element-reflectance relationships for the samples. The top portion of the table refers to the LCC between the percent of light reflected off the samples and the percent of a given element (or its oxide) as analyzed. In the lower portion of the table the LCC refers to the relationship between the same reflectance data and the chemical analyses which have been corrected on the basis of 0% acid insoluble material (chiefly quartz) in the phosphate rock. Each LCC presented in Table I is computed for the 14 coarser samples exclusive of the seven concentrates since the concentrate samples appear to have anomalous reflectivities upon comparison with the coarser grades. Only the most significant LCC for each element is presented in graphical form. Discussion of Data Iron: [Fig. 1] is a graph of the relationship between iron and reflectivity (LCC = - 0.98). A good correlation with Fe2O3, is expected due to the relationship between the tan (or brown) color and the abundance of iron oxide, the principal mode of occurrence of iron in Florida phosphates.8 Note the location of the seven triangles which repre-

Jan 1, 1972

By J. W. Galpin, R. H. Allen

Controlled pre-grouting is a technique developed during a period of more than ten Years experience, in an effort to produce safer, drier and more economical mine shaft sinking. The technique involves a knowledge Of hydro-mechanics, both static and dynamic, and a series of specially formulated grout mixtures to obtain several desired results through precontrolled setting time. In general, the following procedures have been used to secure the best results in controlled pre-grouting: I. Before drilling is commenced, One Of two decisions is made: one procedure, a modified form of the Francois method, is to stage drill and grout, that is, drill a limited portion of the hole, then grout and redrill that section which has been grouted, progressing in stages until the required depth is reached. We prefer this method because no casing Or grouting packers are required in the bore hole. This eliminates the risk of losing them in the bore hole due to packer failure, which might result in the expense of drilling a new grout hole. Another feature Of this approach is that smaller drill holes may be effectively used, further reducing the costs. One drawback, however, is that because of the open and small size hole, it is impractical to attempt water draw-down tests. The second alternative is to drill the bore hole, (generally NX size), to the re-quire~ depth. he casing and grouting packer are placed in the bore hole at the lowest packer setting. A small, portable, power driven, swabbing device is used in the grouting casing to test the packer and remove mud or cuttings from the bore hole below the packer. The hydrostatic level is recorded and a close estimate or test is made of the quantity of water at each packer setting. Grouting progresses upward in a series of packer settings to the surface. Occasionally, casing is inserted in the bot-tom of the bore hole from within the mine, and water pressure and volume can be obtained in this manner. This is usually dangerous because of the unknown quantity of water. 2. The grouting, mining and geological engineers at the drill location make a detailed examination of the cores and also locate proper and firm grouting packer locations. A competent driller,s opinion should be given due consideration as to the character and condition of the bore hole. 3. Several samples of formation water

Jan 1, 1949

By J. R. Campbell

IN order to discuss the subject intelligently, it will be necessary to touch briefly on the forms in which sulphur is supposed to exist in coking coal to be carbonized in beehive or byproduct ovens. Sulphur is known to exist in coal as sulphides and sulphates, as can be determined experimentally. Then there is the so-called organic sulphur, i.e., sulphur in combination with the carbon, hydrogen, and oxygen of the coal, about which much has been written, but nothing definitely proven in an experimental way. In fact, so far as we know, there never has been developed a satisfactory and conclusive method in the laboratory for the direct determination of organic sulphur. For most coking coals, it can be safely assumed that the preponderance of sulphur is in the form of pyrite (FeS2). When exposed to comparatively low temperatures during the coking process, it loses its sulphur according to the following chemical reaction: 7FeS2 = Fe7S8 + 6S. It will be seen, therefore, that six out of the 14 atoms of sulphur (or 42.8 per cent.) are expelled, or volatilized. Fe7S8 remains in the coke as pyrrhotite, or magnetic sulphide of iron; this accounts for the highly magnetic properties of the powdered coke. A more commonly accepted reaction is FeS2 = FeS + S, in which the straight sulphide of iron is produced with 50 per cent. volatilization of sulphur. In the beehive methods of coke making, air is introduced in sufficient amounts to carry on the distilling and the coking processes, and the sulphur is oxidized along with the other volatile products: First, into sulphur dioxide (SO2), known by the pungent and suffocating odoremitted from the trunnel head; second, into sulphuric anhydride (SO3); and, finally, into sulphuric acid, as it comes into contact with the air and moisture. In a properly regulated draft on a beehive oven, there is never complete combustion of the gases. In other words, the coking process should be carried on in a reducing atmosphere, and a low-grade producer gas kept issuing from the trunnel head. For coals of about 30 per cent. volatile matter, the ratio of air to gas is 3 ½ to 1. In complete combustion, the ratio is 6 to 1, producing an extremely high temperature

Jan 1, 1916