Search Documents

By Horace Pops, Jorge E. Kittl

In a recent study' of the martensitic transformation of Cu-Zn ß-phase alloys, it was noted that the MS temperature at the surface was raised due to the loss of zinc by volatilization. It seems likely, therefore, that the MS temperature may serve as a guide for the measurement of composition. From a knowledge of the dependence of the transformation temperature on composition, 2 it should be possible to detect variations in zinc content which are less than 0.1 at. pct by measuring the MS temperature throughout the sample. It is unlikely that an electron microprobe analysis could detect accurately such small zinc losses because the presently accepted limits of accuracy of the micro-probe analysis in simple ternary systems are of the order of 2 to 5 pct of the amount present.3 In the present study, a composition gradient was produced by precipitating the a primary solid solution, and reheating for a very short time within the ß-phase field. The nominal composition, in atomic percent, of the ternary ß-phase alloy used, 64.2 Cu, 34 Zn, 1.8 Si, was selected because it had an MS temperature of +4°C, thereby simplifying the experi-

Jan 1, 1968

By James Gardner

IN 1923, Oklahoma took second place as an oil-producing state; whereas in 1922 it was the leader. California surpassed it, in 1923, by nearly 100,000,000 bbl. In 1923, Oklahoma produced, according to statistics of The Oil & Gas Journal, 165,013,685 bbl., or an increase of approximately 10 per cent. over the preceding year; the increase in California was approximately 90 per cent. The number of wells drilled in Oklahoma and the results of the two years are contrasted in the following table from data published in a preliminary bulletin by the U. S. Geological Survey. 1922 1923 Oil wells 4,149,68%. 3,515, 60% Gas wells 571, 9 %u 587, 11% Dry holes 1,428,23% 1,731,29% Total wells 6,148 5,833 The initial production from wells drilled in Oklahoma in 1923, according to The Oil & Gas Journal, was the largest in the history of the state, being 1,277,936 bbl. It has been 32 years since oil development began in the state, last year being the largest in the amount of production. The production of the past year would have been considerably greater were it not for the shutdown order in the Burbank field and curtailment of production in the Hewitt and Tonkawa pools.

Jan 3, 1924

By C. Bourgoin

"The limited development and application of new technologies to narrow-vein mining is currently impeding progress in the industry to a point where productivity, working conditions and operating costs have reached a critical stage in many Canadian mines.In an effort to foster the emergence and application of new technologies, Université Laval, together with other organizations, has carried out a R&D project focussed on the need of identifying new development pos5ibilities and of facilitating the transfer of technology in matters related to underground mining methods and machinery.The first phase of the study consisted of an in-depth assessment of current practices and problems in narrow-vein mining. The second phase was a state-of-the-art survey of mining methods and equipment, together with proposed modifications and innovations. The third phase of the project concerns the experimental development as well as the principal application of various proposed technologies.This paper presents an overview of the organizational, technical and strategic considerations which guided the University group and it serves as well to introduce a newly-published brochure, entitled ""Underground Mining Techniques of Vein Deposits"", which summarizes such work to date. More specifically, a perspective of technological developments applicable to narrow-vein mining is presented."

Jan 1, 1994

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By A C. Robertson

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authorsÆ personal observations and experience.

Jan 1, 1998

By Les Willan, Chris Batten, Matt Sparkes

In late 2008 Xstrata Newlands Coal Mine in Central Queensland and Orica Mining Services engaged in discussion to investigate methodologies to change their current mining practices and overcome the issues in the mining of steeply dipping coal seams, the associated coal loss risk and to assist in improving mining productivity. A strategy was developed and it was determined that through-seam blasting was essential to the success of winning the coal from the Wollombi Pit at Newlands.

Jan 1, 2010

By Tiago Evangelista Gomes

O presente trabalho teve por objetivo verificar a influência do Nióbio na trabalhabilidade a quente de um aço inoxidável duplex do tipo UNS S32304 em condições similares às do processamento industrial, utilizando ensaios de torção a quente. Foram fundidas, em forno de indução a vácuo, 4 corridas experimentais: uma com a composição química padrão e as outras objetivando-se teores de Nióbio de 0,2%, 0,4% e 0,8%. Ensaios de torção a quente foram realizados em resfriamento contínuo a partir de 1.200ºC, e ensaios isotérmicos no intervalo de temperaturas de 1.200 a 900ºC. O aumento da fração volumétrica de ferrita em função do aumento da concentração de Nióbio melhorou a trabalhabilidade a quente destas ligas.

Jul 30, 2018

By R. V. Lundquist

Lime-soda sinters, made and processed for recovering alumina and soda, consisted of several types of compound structures differing from the ideal dicalcium silicate and sodium aluminate. Many or these compound structures were causes for low alumina recovery and contributed to the relation or leach slurries. Presence or free lime, whether in the sinter or released by hydrolysis of sinter compounds, contributed to relation of leach slurries. Free lime tends to establish the initial viscosity assumed by a leach slurry. Previous investigations by the Bureau of Mines (1, 4)4/ and by other laboratories (5) have demonstrated the technical applicability of the lime-soda sinter process to the recovery of alumina from aluminum silicate materials. The basic concept of the process is sintering aluminum silicate materials with limestone and soda ash for the production of dicalcium silicate and sodium aluminate and then extracting the sodium aluminate by leaching the sinter in causticized liquors. Alumina is precipitated from the pregnant liquors by carbonating with carbon dioxide. Reaction in the sintering operation may be represented by the following simplified equation: A1203?SiO + 2CaCO3 + Na2C03 = 2Ca0?SiO + Na20?Al203 + 3C02

Jan 1, 1960

By M. S. Hedley

"The Lucky Jim mine is at Zincton in Slocan mmmg division; on the Kaslo-Nakusp branch of the Canadian Pacific railway. It is owned and operated by Zincton Mines; Limited; a subsidiary of Sheep Creek Gold Mines; Limited. The mine is far in the lead in the production of zinc in the Slocan. Its recorded production from concentrates and shipping ore was 102; 260; 191 pounds of zinc to the end of 1945.GENERAL GEOLOGY With the exception of acidic dykes the rocks near the Lucky Jim mine belong to the Slocan series, which is Triassic in age and consists principally of argillaceous rocks. It disconformably overlies greenstones of the Triassic Kaslo series about 3 miles to the northeast, and is cut by granitic rocks of the Nelson batholith 5 miles to the southeast.The sedimentary rocks in this area are best referred to on the whole as slates. They lie within the more fissile basal part of the Slocan series. The term 'slate belt' conveniently distinguishes this area of rocks characterized by slaty cleavage from the more massive argillites that are more characteristic of the Slocan as a whole. The contact between the slaty and massive argillites lies ½ mile southwest of the mine."

Jan 1, 1954

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978

Measure dangerously high concentrations (20 to 500 g/m3) of flammable, airborne dust. Approach Development of high concentration dust monitor (HCDM) which will measure mass concentrations of air borne dust by the principle of beta-ray attenuation. How It Works The HCDM is a battery powered, portable instrument that weighs 10.5 kg. It is capable of making continual (10 sec. time resolution) measurements of high concentrations of airborne dust and can record up to 8 hours of data in an internal memory. The data can be read out later on an analog or digital recorder. An internal pump pulls airborne dust into the sampling section, which contains a low-energy beta-ray source and a Geiger counter detector. No beta radiation escapes from the instrument, and no license is required for the operator. The mass concentration measurement is made while the dust is still airborne. Beta-ray attentuation is independent of particle size and composition of the dust, so the HCDM can he used with many types of dusts which may be airborne in flammable concentrations. A knowledge of the composition and minimum explosive concentration of the dust is necessary to understand the significance of the data from the HCDM. The HCDM was designed to measure air-

Jan 1, 1982

By John A. Dearinger, Fred D. Wright, Robert C. Howell

INTRODUCTION The rock mechanics study of the shortwall mining system at Beth-Elkhorn corporation's Hendrix No. 22 Mine is being conducted under contract with the U.S. Bureau of Mines. The objective of the study is to obtain data on surface subsidence over a portion of the mined area, strata subsidence in the mined area, and underground stress changes and displacements in and near natural support elements of the mining system. This study is currently in progress, and only a portion of the results are being presented at this time. The Hendrix No. 22 Mine is located in the moderately rough mountainous terrain of Letcher County in eastern Kentucky. The nearest mine workings to the shortwall area are approximately 1,900 feet distant. The depth of cover over the mined shortwall area varies from 770 feet at Panel 1 to 170 feet at Panel 5 (Figure 1). The strata in the shortwall area is summarized in the three core logs shown in Figure 2. Hole no. 2 is located in approximately the center of the mined shortwall area (Panel 3, Line C, Figure 1). The coal seam in the shortwall area is approximately 4 feet thick and horizontal, although one major ‘roll’ intersects all panels.

Jan 1, 1977

By Lívia Silvestre Andrade

Uma das rotas mais importantes de produção do Fe-Nb para aplicações siderúrgicas é a aluminotermia. Para que o processo seja eficiente, é necessário projetar adequadamente a escória, para garantir a mínima retenção de metal na escória e reduzir as perdas, assim como determinar a carga da aluminotermia considerando os balanços de massa e de energia. Neste trabalho, os efeitos das adições de CaO e CaF2 sobre as características das escórias do processo são determinados através da termodinâmica computacional. Um balanço de massa e um balanço de entalpia são formulados, de modo a verificar se as quantidades dos diversos materiais adicionados são adequadas e se as temperaturas de fim de processo são razoáveis. Verifica-se que, a partir de uma carga hipotética formulada, há espaço para melhorias importantes balanceando-se corretamente as adições de CaO e CaF2. Além disto, verifica-se a influência do teor de Mg contido como impureza no Al empregado como redutor, observando-se que seu efeito é bem menos significativo do que inicialmente esperado por diversos operadores.

Oct 30, 2017

By Luara da Costa Morais

O objetivo deste trabalho é avaliar a influência da temperatura de recozimento intercritíco na microestrutura e nas propriedades de um aço dual-phase. Para isto, amostras do aço em estudo foram recozidas intercriticamente a temperaturas entre 720 e 740°C. A quantificação da martensita foi realizada por estereologia quantitativa sobre imagens obtidas por sinal de elétrons secundários. Ensaios de tração e de estampabilidade foram realizados no material tratado e na condição de partida. Os resultados da quantificação mostraram aumento na fração de martensita com o aumento da temperatura de tratamento. Para o estudo da influência da microestrutura no comportamento mecânico, foi relacionada a fração de martensita com as propriedades mecânicas obtidas nos ensaios de tração e estampabilidade. As amostras recozidas intercriticamente apresentaram aumento nos limites de resistência e escoamento e diminuição dos alongamentos, total e uniforme, com o aumento da fração de martensita. A amostra de partida apresentou frações de martensita similares às observadas para a tratada a 740°C, entretanto com valores de resistência e escoamento inferiores e alongamento superior, sugerindo influência da morfologia nas respostas mecânicas do material. O material como recebido apresentou a melhor combinação entre resistência, alongamento e estampabilidade indicando que esta condição é mais indicada para o setor automotivo.

Aug 8, 2018

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005

By Evan J. Owen, Virginia T. McLemore

of high specific gravity, resistant minerals that form from mechanical concentration by waves, currents, and winds in marginal-marine environments. These sediments are enriched in critical minerals such as titanium, zirconium, and REE. Cretaceous beach-placer sandstones are found in the Colorado Plateau of northwestern New Mexico. Originally discovered by airborne radiometric surveys for uranium in the 1950s, these beach-placer sandstones are being re-examined with modern methods as potential sources for critical minerals. Selected beach-placer sandstones have been sampled, mapped with ground radiometric surveys, and analyzed with whole-rock and trace element geochemical methods. Mineralogy is being determined with optical methods, XRD, and EMPA. Zircon, rutile, ilmenite, and monazite are the primary heavy minerals of interest found in the studied deposits. Initial results show that the sandstones contain up to 1.4% total REE, 29.4% TiO2, and an estimated 4.9% ZrO2. Chondrite-normalized REE diagrams show distinct light REE and minor heavy REE enrichment, as well as pronounced negative Eu anomalies for each deposit.

Feb 1, 2024

By Jason Swartz, Gerardo Gomez, Henry Leighton

San Antonio has experienced sustained growth for decades, putting increased pressure on existing wastewater infrastructure. In June 2013, San Antonio Water System (SAWS) reached a Consent Decree agreement that requires significant improvements to the wastewater system over a 10-year period to reduce Sanitary Sewer Overflows. One of the critical projects was the W-6 Upper Segment Tunnel project to reduce sanitary sewer overflows on an existing sewer main running through Lackland Airforce Base. The replacement project consisted of a new tunnel nearly 29,000 LF of primarily 104" FRP. The project also includes nine shafts and multiple trenchless crossings to make near surface connections to the new works.

Jun 23, 2024

By Heidy de Oliveira Simões

O objetivo deste trabalho foi estudar as correlações entre o IPM (Índice de Permeabilidade Magnética) das pelotas queimadas, as trincas formadas durante o processamento das pelotas no pelotamento/endurecimento e o FeO de cada amostra. As análises evidenciaram que o tipo de trinca presente na pelota impacta no IPM fazendo diminuir a correlação entre IPM e FeO. O entendimento do fenômeno possibilitou desenvolver uma metodologia para determinação de um parâmetro que pudesse ser correlacionado ao FeO das pelotas de minério de ferro, estendendo sua aplicação ao pellet feed, baseado nas propriedades magnéticas do material. O método consiste em medir a variação da indutância de um solenoide, provocada pela introdução do material que se deseja determinar o parâmetro no núcleo de uma bobina, determinando-se relativamente a permeabilidade magnética das pelotas e pellet feed. Para tal, foi definida uma metodologia nas quais alterações devidas à variação da densidade da amostra, causadas principalmente devido a trincas nas pelotas, sejam mitigadas, garantindo a repetibilidade dos resultados. Assim, foi possível a determinação do FeO das amostras através da medição deste novo parâmetro, de forma mais rápida, fácil e com um custo consideravelmente menor que na química analítica clássica.

Aug 1, 2018

By Ramon Santos Corrêa

Com a descoberta de poços de petróleo cada vez mais profundos, as tolerâncias das propriedades mecânicas dos tubos de aço utilizados para este fim estão mais restritas. Somando-se a isso, o mercado pressiona por redução de custos e agregação de valor nos produtos ofertados. Por outro lado, a maturidade de interconexão alcançada pelos sistemas industriais, permitiu a disponibilização de dados mais precisos dos processos e a utilização de ferramentas computacionais avançadas de análise e modelagem de dados. Este trabalho tem como objetivo prever as propriedades mecânicas dos tubos após o processo de revenimento, a partir da composição química do aço, parâmetros dimensionais dos tubos e parâmetros do processo. O acompanhamento on-line da tendência das propriedades mecânicas permitiu uma operação preventiva no forno de revenimento, possibilitando a redução do lead time do processo, visto o tempo médio de 2 dias para o recebimento dos resultados do laboratório. A definição pela utilização das Redes Neurais Artificiais se baseou em trabalhos relacionados ao tema e casos de sucesso aplicados na indústria. Observou-se que os resultados obtidos a partir dos modelos obtiveram índices de assertividade superiores aos de outras técnicas utilizadas para este fim. Além disso, foi possível a criação de um único modelo para cada propriedade mecânica considerando todas as famílias de aço produzidas na Vallourec, facilitando os processos de calibração e sustentabilidade dos modelos.

Aug 16, 2017