Search Documents

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By Pedro Damas Resende

As propriedades físicas e mecânicas de ligas NiTi são fortemente influenciadas pelo seu histórico termomecânico. Este trabalho visa avaliar a influência de uma deformação preliminar (chegando ao escorregamento da martensita) aliada ao recozimento de uma liga NiTi sobre suas propriedades através de DSC (Calorimetria Diferencial Exploratória), ensaios de tração até a ruptura e difração de raios X (DRX). Observou-se um aumento da histerese térmica como resultados dos tratamentos, e as transformações martensíticas passaram a ocorrer com formação de fase intermediária (fase R) para os grupos recozidos. Os valores de tensões de início e fim de patamar do grupo tratado diminuíram em relação ao grupo do material como recebido.

Aug 16, 2017

By Christoph Aichinger

A smart combination – Primetals Technologies developed the Circular Pelletizing Technology (CPT), which is a combination of the well-proven travelling-grate pelletizing technology with the design of a circular dip rail cooler of modern sinter plants. The overall space requirement and the installed weight for a CPT plant is significantly less compared to conventional technologies and by that CPT is a very attractive alternative for new projects.

Aug 16, 2017

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By Vitor Vianna de Castro Moreira, Danilson Gonçalves de Melo e Silva, Gabriel Augusto da Fonseca

The present work aims to describe the changes made in the operational procedure of the reheating shell furnace, of the hot-rolling of seamless tubes line at Barreiro Plant of VSB, during non-production periods, focusing on reducing natural gas consumption. According to the previous procedure, the furnace was kept at 750°C on these periods, using the main burners. With the new procedure, the furnace is naturally cooled, maintaining only the auxiliary burners with a pilot light turned on, without worrying about the conservation of temperature. Subsequently, the furnace is heated with a rate of 150 ºC/h until it reaches the setpoint temperature of production. This procedure change was successful and didn’t cause operational and security problems. The minimum stoppage time needed for the natural cooling to be economically favorable is 6 hours and 30 minutes. The new procedure reduced the natural gas consumption in 4.500 Nm³, considering 24 hours of stoppage, achieving an estimated annual economy on the thermal energy costs of R$440.000,00 in 2019.

Oct 3, 2019

By J. L. Gregg

A STUDY of copper and silver base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.1 This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys.

Jan 1, 1929

By D. G. Krige

The problem of a realistic investment analysis for a new mining venture that sells its products on the international metal markets IS studied against the background factors, firstly, of different inflation rates between the countries hosting the mines and those. hosting the metal markets; and, secondly, of the changing pattern of currency exchange rates between such countries. The purchasing-power parity theory is used to establish a pattern of relationship between these two factors, and to develop a more logical approach to the long-term forecasting of metal prices in the currency of the country in which the mine is situated.

Jan 1, 1979

The General Electric Co., in cooperation with the Montana School of Mines and under a research grant from the Anaconda Co., is presently experimenting on a new non-explosive method of breaking rock with radio-frequency electrical power. The method is known as electrothermal forcing. It must be understood that present equipment has not been designed to perform primary blasting functions. Its conceived use will be restricted to small pieces of rock too large to pass through a chute or grizzly. However, even this use is still far in the future. Experiments to date have been limited mostly to rock smaller than 18 in.

Jan 11, 1961

The following Nominating Committee having been already appointed and approved by the Executive Committee in accordance with authority vested in the Executive Committee by the Board of Directors, was approved by the Directors: John V. N. Dorr, Chairman, Percy G. Beckett, J. W. Hutchinson, Julian Kennedy, William H. Linney, Charles W. Merrill, and E. Gybbon Spilsbury. The question of the purchase of Liberty Bonds, as well as that of bringing to the attention of the members the advisability of the purchase of these bonds, was referred to the Finance Committee. Sixty Members, four Associates, and thirty-six Junior Members were elected. Two Members were reinstated. Eight resignations were accepted.

Jan 7, 1917

By Hongpu Kang

The fully mechanized top coal caving mining method has been the main mining approach for thick coal seams with high output and efficiency in Chinese coal mines. The gateroads for the top coal caving mining faces should be driven along the floor of the thick coal seam with a part of the seam as roof. The support of the gateroads is commonly difficult because of the low strength and broken structures of the coal seams, and the increasingly large section of gateroads meeting the need of greater and greater face coal output. Based on the analyses on the geomechanics properties and production conditions of the top coal caving mining, the influences of the top coal caving mining parameters on the stability of gateroads, including mining thickness and face length, are studied. The deformation and damage features of the rock mass surrounding the gateroads with the top coal seam as roof are investigated, the interaction of the support with the surrounding rock mass, the support theory are studied. The bolting design method and criteria, bolting forms and parameters for the gateroads with the top coal as roof are put forward. The rock bolting components, including bolt bars, face plates, cable tendons, meshes, and steel straps, are introduced. Finally, the gateroad bolting effects are evaluated through a typical case study on the basis of field monitoring data, such as the displacement of surrounding rock mass and the forces along bolts and cables.

Aug 1, 2013

By P. Rosario

During the last few years high-tonnage plants have been designed with comminution circuits using semiautogenous grinding (SAG) mills, high pressure grinding rolls (HPGR), or both, followed by ball mills in different configurations. A strong interest in improved energy efficiency and reduction of carbon footprint, along with the recent launch of new high-capacity crushers and stirred grinding mills, has driven the industry to investigate the development of novel flowsheets. This paper presents work based on recent projects that include modeling and simulation of two innovative circuits recently considered for current projects. One circuit uses autogenous (AG) mills and parallel trains of crusher-HPGR and the other is a modified three-stage crushing circuit with the use of HPGRs and pebble mills. The paper indicates the potential savings in operating costs provided by the HPGR-pebble mill circuit when compared to a more conventional SAG-mill-based circuit.

Jan 1, 2010

By Chase K. Barnard, Rahul Thareja, Sean Warren, Rajagopala Kallu

"Inflatable rock bolts are commonly utilized for ground support in Nevada underground mines, however, there is limited information regarding what factors influence the bond strength of these bolts. Bond strength is an important parameter in friction bolt support design, and this information is usually not available from manufacturers as a standard. Previous research has investigated the bond strength of friction bolts; however, these studies focused primarily on split set bolts and ground conditions more favorable compared to those commonly encountered in Nevada underground mines. Without site-specific bolt pull-out tests, ground control engineers are required to make assumptions regarding the in-situ bond strength of rock bolts. This is especially a concern for projects in the feasibility and initial development stages before site-specific experience is acquired.The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the Rock Mass Rating (RMR) system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively correlated with RMR, however the correlation is not strong. Cumulative percent graphs indicate that 97% of pull-out tests result in a minimum bond strength of 1 ton/ft and ½ ton/ft in RMR =45 and <45, respectively.Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed."

Jan 1, 2015

By C Hawtin, B Miller, D Ashton

Ernest Henry mine (EHM) is an Iron oxide copper-gold sublevel cave mine located 30 minutes north of Cloncurry in North-West Queensland. The underground mine lies beneath open pit excavations, which were in operation from 1999 to 2011. Fault structures carry large quantities of water from the cover sequence aquifer into the underground mine area. The open cut excavations exacerbates vulnerability of the underground mine to the high intensity wet season storms of northern Queensland. These factors combine to make hydrogeological issues high priority for mine operation. Water-related risks include the cost of removing water from the mine, flooding risk and mud rush potential.Turnover of key technical staff in late 2015 at EHM resulted in the mine being left in an untenable position of losing the primary source of technical knowledge. Due to encouragement of cross-disciplinary activity coupled with workload and resource sharing, the management team were confident in utilising on-site personnel to offset loss of experienced personnel.Remaining geology personnel took additional responsibility for hydrogeological monitoring equipment and planning of upcoming work. Consultant input was limited to review only and an emphasis was placed on knowledge transfer to the geology team. Using this strategy, a 13 hole dewatering program was successfully implemented, achieving a significant water level drop in areas of elevated hydrological risk, whilst also upgrading the hydrological monitoring sensor array.Through a development program centred on cross-disciplinary exposure, the technical team was able to retain key technical knowledge despite staff turnover and produce strong results outside traditional training and roles. This paper serves as a case study on the methods, strengths and drawbacks of putting a focus on cross-disciplinary exposure as a method to combat staff turnover.CITATION:Ashton, D, Miller, B and Hawtin, C, 2017. Go with the flow – managing hydrogeological staff turnover at Ernest Henry mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R. Kramer, A. Habibi

"Diesel Particulate Matter (DPM) measurements were taken at Tronox’s Westvaco Trona mine in Wyoming. Both shift-average and real-time monitoring using Elf pumps and Airtec analyzers, were used. The mine’s underground transportation fleet consists of more than 250 diesel-powered vehicles. A vehicle monitoring log tracked fleet usage during the test; logged data consisted of vehicle type, direction of travel, and time. The log was used in analysis to determine the DPM spread rate, of normally operating equipment, in the different entries with respect to vehicle location. Airflow velocity measurements at the stations were taken during the survey. The survey results also identified vehicles with higher emission rates. An ECOM gas and a MAHA DPM analyzer, both located in the mine’s underground emission shop, were used to obtain various vehicle emission rates. The correlation of the workshop and field measurements was investigated with regard to the machine activity, fuel usage and atmospheric conditions. The results were used to identify and execute a ventilation project to reroute 45% of diesel shop air back to intake entries, by interlocking an automated door and a regulator. The result is reduced DPM downstream. INTRODUCTION DPM has been classified as a potential occupational carcinogen by the National Institute for Occupational Safety and Health (NIOSH).The Mine Safety and Health Administration (MSHA) rule governing DPM exposures in metal and nonmetal mines cites total carbon (TC), a summation of elemental carbon (EC) and organic carbon (OC) obtained by NIOSH Method 5040, as a surrogate for determining DPM exposures (Noll, 2006). MSHA personnel use the 1973 sampling criteria outlined by the American Conference of Government Industrial Hygienists (ACGIH) for collecting compliance-based respirable and inhalation samples in metal/nonmetal mines. Instrumentation developments are allowing improved real time monitoring of ventilation parameters. DPM is within the aerodynamic particle size range of the samplers used for respirable and inhalable dust measurements. If a sampler used by MSHA to collect inhalable or respirable dust samples in underground metal/nonmetal mines was used to collect DPM, both the DPM and mine ore dust would accumulate on the sample filter (Noll, 2006). To comply with the requirement and lower the DPM exposure, mines are implementing a variety of control technologies such as emission based maintenance programs where adjustments or repairs are performed on the vehicles (McGinn, 2000)."

Jan 1, 2016

By Marcus Vinícius Pereira Arruda

A moderna construção automotiva vem adotando uma série de estratégias para tornar os carros cada vez mais seguros e ecológicos. Dentre elas, o uso intensivo de aços de alta resistência tem proporcionado grandes avanços nos automóveis, principalmente aqueles ligados à segurança veicular. A escolha de um determinado aço é hoje definida, não só pela resistência mecânica, mas também pelos atributos do material ligados a sua aplicação. Assim, a composição química, as variáveis de processo, e, consequentemente, a microestrutura do aço, devem ser reflexo desses atributos. O presente trabalho apresenta o desenvolvimento de um aço multifásico da classe de resistência de 1180 MPa na Usiminas, assim como suas características mecânicas que influenciam a sua aplicação. São apresentados aspectos das simulações efetuadas em escala piloto, a consolidação das informações obtidas e o trabalho de engenharia de produto realizado para o desenvolvimento industrial.

Oct 30, 2017

By M. Balamurali, K. M. Seiler

Modelling stockpiles is a key factor of a project’s economics and operation in mining, because not all the mined ores are not able to mill for many reasons. Furthermore, the financial value of the ore in the stockpile needs to be reflected on the balance sheet. Therefore, automatically tracking the boundaries of the stockpile facilitates the mine scheduling engineers to calculate the tonnage of the ore remaining in the stockpile. This paper suggests how the dynamic of stockpile shape changes caused by dumping and reclaiming operations can be inferred using polygon models. The paper also demonstrates how the geometry of stockpiles can be inferred in the absence of reclaimed bucket information, in which case the reclaim polygons are established using the digger’s global positioning system (GPS) positional data at the time of truck loading. This work further compares two polygon models for creating 2D shapes.

Sep 1, 2021

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By Modesto Pereira Júnior

A operação da moagem é de grande importância na mineração, uma vez que é a área da fragmentação que requer maiores investimentos, há maior gasto de energia e seu desempenho afeta diretamente a taxa de recuperação do mineral de interesse. O controle do circuito de moagem é desafiador por se tratar de um sistema multivariável, não-linear e por se caracterizar pela existência de forte acoplamento entre variáveis e diferentes atrasos de tempo. Na indústria, grande parte desses circuitos é controlada apenas por PIDs. Nesses casos, quando há perturbações no sistema, tais como variação do tamanho das partículas na alimentação ou variação na dureza do minério, a interferência de operadores alterando setpoints é exigida para manter a estabilidade do sistema. Neste trabalho é desenvolvido um controlador fuzzy multivariável aplicado a um simulador de moagem. A camada de controle proposta encontra-se acima da camada regulatória. O objetivo é o de variar dinamicamente os setpoints dos PIDs para maximizar a taxa de produção dentro de uma faixa granulométrica.

Oct 30, 2017

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry&apos;s perspective on a number of the issues currently being addressed at EPA&apos;s Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992