Search Documents

By K Louie

When BHP Copper's Lower Kalamazoo Project commenced production in January 1997, two of the four original hoists had been converted to hoist ore from the Lower K level. Conversions on these hoists not only allowed hoisting from a much deeper level, but also created a higher hoisting efficiency and higher capacity as well. Conversions included new drums, new cables, SCR drives and other solid state control technologies not available when the original hoists were installed. Two of the original hoists were installed in the 1950's and the other two were installed in the 1970's.

Jan 1, 1998

By Jesus Layten, Marcos Garayar

Los RPAS (Remotely Piloted Aircraft Systems, por sus siglas en inglés) o drones son aeronaves (plataformas) que vuelan sin tripulación de manera automatizada, a las que se les puede adaptar diversos tipos de sensores. Esta tecnología nos brinda la posibilidad de obtener imágenes de alta calidad y precisión, de manera eficiente, confiable, segura y de menor costo. Asimismo, permite realizar trabajos en zonas de difícil acceso, ya sea por razones geográficas o sociales. El desarrollo de los trabajos con drones involucra una serie de procedimientos y técnicas que se abordarán en el presente trabajo, junto con ejemplos de levantamientos exitosos realizados en proyectos mineros y de infraestructura en Perú.

Sep 20, 2019

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Matheus Martini

A escória de aciaria LD é um coproduto abudantemente gerado através da metalurgia primária e secundária, sendo que após seu resfriamento e beneficiamento pode ser aplicado em diversos setores, mas que necessita ser submetido a processo de envelhecimento para minimização da expansão. Em geral, no Brasil, o Método PTM-130/78 é o mais utilizado para avaliar o potencial de expansão, entretanto o método leva 14 dias para obtenção dos resultados. Por meio de uma cooperação técnico-econômica entre a CSN e a EEL-USP, o método de expansão foi correlacionado com as fases identificadas e quantificadas por Difratometria de Raios-X e Método de Rietveld, respectivamente, além de compreender o mecanismo de expansão. Análises de regressão múltipla permitiram ajustar modelos matemáticos com 97,0% de ajuste e uma redução no tempo de ensaio de 14 dias (336 horas) para 7 horas.

Aug 16, 2017

By M. Brnich, S. Kramer, B. McNamara, T. Hethmon, M. Pedersen-Howard, S. Rajapaske, D. Lingenfelder, B. Huber, D. Hebig

"The development of mining safety and health management as a recognized profession has been long in coming. Over the last 150 years, the mining industry has evolved from having individuals randomly involved in safety related work with no specific responsibilities or qualifications, on to the designation of individuals responsible for safety, regardless of knowledge, qualifications and experience and finally to today’s expectation that virtually every mine and mining company has designated individuals operating as safety and health professionals. Further, with the complexity, risk potential and moral expectations surrounding safety, people who address mine safety and health management are justifiably expected to function in a professional capacity including:1. Rendering a specialized service based on advanced knowledge and skill.2. Maintaining a high degree of obligation to those most affected by mine safety outcomes.3. Bound by an ethical code in working with the public, employers and miners.4. Maintaining confidentiality with an employer or client. This historical change parallels thedevelopment of other professions, e.g., attorneys, engineers, physicians, etc., with the exception that those professions require a license granted by a governmental agency, which is justified on the basis of public protection, in order to practice. Likewise, decisions made by today’s mine safety and health professionals, both directly and in association with other managers, clearly have a significant impact on the life and welfare of miners throughout the world.CertificationIn light of this, there is growing need to improve standards of competency and professionalism for those who work in mine safety and health management. An effective mechanism to accomplish this, other than licensure, is the use of accredited professional certification programs. There are many professional certification programs for safety and health throughout the world (Hale & Harvey, 2012). However, there is only one certification specific to mining —the Certified Mine Safety Professional (CMSP). The International Academy of Mine Safety and Health (ISMSH-SME) was formed with the purpose of developing and managing mining safety and health certification programs for the Society for Mining, Metallurgy and Exploration (SME). In 2016, following the discontinuation of the International Society of Mine Safety Professionals (ISMSP), which developed the Certified Mine Safety Professional (CMSP) credential in the 1990s, the IAMSH-SME began the process of updating and relaunching the CMSP program. Among other work required to gain third-party accreditation both domestically and internationally, the IAMSH-SME has developed a new Body of Knowledge associated with mine safety and health management (Table 1)."

Jan 6, 2018

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By Fernanda Ferrante, Wagner Reis Modesto Ribeiro, Eduardo Pena Carvalho

CSN Mineração S.A. is the second largest exporter of iron ore in Brazil and is among the five most competitive in the market. Casa de Pedra currently has an approximate production capacity of 30 million tons per year. The fleets of small trucks 6x4 and 8x4 models are responsible for the ore movement, traveling an average distance of 10 km between origin and destination. 116 trucks of this size are used in CSN Mineração for the handling of products. Every month this fleet consumes an average of 550,000 liters of fuel. The objective of the work is to do a fuel consumption analysis by truck through the embedded telemetry system. The reports generated through this system provide the specific consumption of each equipment and also the specific consumption of each Driver. As reports are generated it is possible to assess which equipment had a higher specific consumption and, in this case, the respective trucks with greater consumption are directed to the Maintenance team for analysis and action in the event that a problem is identified in the equipment. At the same time, the analysis of the drivers who had the highest specific consumption and conducted a practical and theoretical training, addressing the techniques for a safer and therefore economical direction, is carried out. In 2019, the economy of fuel consumption type S10 was 204 thousand liters, which represents 9% of all consumption foreseen for the period.

Oct 3, 2019

By K. Johnson, B. Schiffer

Demonstrating aquifer restoration is an essential component of regulatory approval needed to mine uranium, copper, and other minerals by in-situ recovery (ISR). A PHREEQC geochemical model provided a useful means of forecasting the time for restoration and predicting future groundwater quality following low pH mining at Strata Energy’s Ross ISR Project in northeast Wyoming. The model simulated groundwater quality at three phases of the process: at the end of mining; during restoration; and post- restoration. The model utilized the one-dimensional reactive transport and dual porosity features of PHREEQC. Mineral surface ion-exchange, dissolution/precipitation reactions, and adsorption processes were simulated to estimate water quality as the pH was shifted from circumneutral to acidic during mining and back to neutral during restoration. The model results showed that cost-effective management of mine water could meet regulatory requirements. Additionally, the model was used to interpret results from a field trial and inform operational decisions. The predictive approach and geochemical understanding developed have application in assessing aquifer restoration for other ISR projects.

Mar 2, 2022

By Jan Reimann

Increasing individualization with smaller quantities, growing competition from low-wage countries, and the continuous drive towards digitalization are the challenges that industrial companies in high-wage countries must face. The example of the Flender One gearbox modular system demonstrates how consistent standardization and digitalization are the enablers for AI, and thus already enable new business models and business approaches today.

Feb 22, 2026

By Michel Fillon

Hydrostatic assistance is a commonly used method to improve limited load carrying ability of tilting-pad thrust bearings during transient states of operation of the vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves etc.), it also requires manufacturing of special recesses/pockets at the pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up of the machine and form a hydrostatic film between the pads and the collar. There is a quite wide variety of geometry of recesses (shape, depth, size) met in practical large bearing applications. The presence of a hydrostatic pocket (usually located in the sliding surface above the pivot area, where thin film, high oil pressure and temperature are observed) affects bearing performance under hydrodynamic operation. In theoretical researches, there is an almost common practice not to include hydrostatic recess in THD or TEHD analysis. This is probably due to the problems with obtaining solution for oil film geometry with pocket, with pocket depths order of magnitude larger than gap thickness. In this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of ltaipu power plant. Bearing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket.

Jul 31, 2018

By M. Sears, W. H. Su, J. Wickline, M. A. Van Dyke, G. Esterhuizen, Z. Khademian

It is commonly recognized that seismicity can be induced by rock failures or slip along geologic structures around mining excavations. The unpredictable nature of these events and their proximity to the working area may raise safety concerns in underground mining operations. Modeling can be a useful tool for estimating seismic potential for a given mine layout, but the challenge is to detect a seismic event and estimate its intensity in the model. One well-documented approach is to monitor the variation in the energy content of the model and record potentially damaging seismic events when there is a significant release of energy. Researchers from the National Institute for Occupational Safety and Health (NIOSH) employed this approach using 3DEC modeling software to simulate the anomalous seismic events that occurred in a deep longwall mine in Virginia in 2005. A four-panel model of the mine was constructed utilizing a 2D cross section at the location of the mining face at the time of the event. Seismic potentials associated with the development of each panel are evaluated by recording the seismic energy released during the simulation. The results demonstrate the occurrence of two relatively significant events during the mining of the last panel, which are consistent with the historical observations at the mine.

Apr 26, 2022

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Bruna Brito Freitas

O lingotamento contínuo de tarugos é um processo extremamente complexo dependente de uma série de variáveis. Todas essas influenciam diretamente na qualidade do aço lingotado e na produtividade, quase sempre de maneira conflituosa. Para compreender o efeito dos parâmetros de processo, é necessário conhecê-los melhor e avaliar sua influência naquilo que é a base do lingotamento contínuo: a transferência de calor na interface metal/molde. Neste estudo foram levantados dados de temperatura durante o lingotamento de diversas corridas de aços em uma planta de aços longos especiais. As medidas de temperatura das paredes do molde da máquina LC foram obtidas, utilizando-se termopares estrategicamente posicionados ao longo do comprimento do molde e nas suas faces. Através da obtenção dos valores de temperatura desses termopares e do levantamento dos dados de processo de cada corrida monitorada, foi possível correlacionar o efeito da composição química com a transferência de calor na interface metal/molde. Por fim, os resultados mostram que aumentando o carbono equivalente observa-se um aumento na transferência de calor.

Aug 7, 2018

By Juliana Simões Chagas Licurgo

Este trabalho tem por objetivo avaliar o efeito da incorporação de até 40% em peso de um resíduo gerado na forma de lama proveniente da etapa de lapidação da fabricação de vidros em cerâmica vermelha. Inicialmente o resíduo foi caracterizado pelo emprego das técnicas de fluorescência de raios-X, peneiramento e sedimentação e dilatometria ótica. A plasticidade das composições foi determinada pelo método de Atterberg. Corpos-de-prova foram obtidos por prensagem uniaxial a 20 MPa e queimados nas temperaturas de 900 e 1000ºC. As propriedades físicas a mecânicas avaliadas foram: retração linear, absorção de água e tensão de ruptura à flexão. Os resultados indicaram que o resíduo é apropriado para o uso em cerâmica vermelha em mistura com argilas, contribuindo para reduzir a absorção de água e aumentar a resistência mecânica da cerâmica nas temperaturas investigadas.

Aug 16, 2017

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By Jesus Pascual, Benjamin Cebrian

A new Convention Center is going to be built in the millenary city of Toledo, right in the old city limits. The workings will need to excavate some 80.000 cubic meters of granite, which has, a trench-like structure already blasted for the construction (60 years ago) of a parking lot and a shopping area. Surrounding this trench, some few feet away, there are structures and buildings from the 16th century and remainings from previous times that need to be preserved from any damage caused by blasting. Because of this, a vibration analysis was designed according to the special characteristics of this work. Structures to monitor were located at several levels. It considered three different directions of study in order to evaluate the impact of vibrations of the structures located at three different heights of the granite trench. On top, the historical convent of Santa Fe, with some remaining from the 8th century (Muslim domination of the Iberian Peninsula), on the bottom, the Justice Hall of Toledo with 16th century walls, and, in the middle, a wall and a tower from times of the king Phillip II (16th century, the time of the Spanish Empire).

Jan 1, 2004

By A Dunne, R Kruger, H Coleman, P G. Laurens

External and internal challenges in mining are increasing the difficulty and complexity of operating mines. The external mining environment has a big impact on mining operations and is driving the focus on safety, sustainable mining, green issues, profitability and productivity. There is a very high emphasis on ‘reducing cost to improve’, lower mining and beneficiation costs by eliminating waste/inefficiencies (reduce people, use less consumables, multiskilling, etc). The internal mining environment is getting tougher to operate in, with the deposits being more difficult to mine, more difficult to manage due to external pressure along with issues associated with maintaining quality, etc.Technological and environmental developments too numerous to mention, mean that cost control models, reduction in human resource numbers, as well as other drastic measures to curtail expenditure and increase profitability have become part of everyday business. The capability to manage the mining environment in a systemic manner has been lacking and this increases the pressure for performance on those individuals operating and managing mines.Working smarter has become crucial to ensure that businesses optimise the use of their resources, become more safety conscious, more productive and remain cost-effective, while recognising the importance of sustainable mining now and in the future. The logic of determining and managing to the capability of the mining value chain will be examined and the underlying assumptions or beliefs guiding behaviour and decision-making will be highlighted.In order to identify the obstacles in the mining value chain that hinder achievement of its full potential, the following questions have to be asked:What are the factors that influence the performance of a mining value chain?What is the design capacity of the mine?How can the inherent flow and value capacity of a mine be determined?What types of solutions will allow a mine to operate at its inherent flow and value capacity?This article will discuss the way we plan, measure, assess and manage the mine value chain, by addressing the following factors:balanced capacity versus flow and value capacity designthe use of averagingoptimising individual components in a value chain versus optimising the whole value chain.Optimising flow and value through the mining value chain is one of the three pillars of Mineral Resource Throughput Management (MR™). MR™ is an entrenched and academically supported philosophy that has been successfully applied in the past decade in various mines throughout the world by EXXPLEO, a mining and beneficiation consulting company. EXXPLEO has partnered with HCL (a global IT company) to embed the MR™ philosophy, methodology and toolsets into a formal software product called Synchronised Digital Mining (SDM). The SDM system will provide mining companies with a sustainable platform to effectively apply the MR™ principles and toolsets effectively across all operations targeting increased productivity, efficiency and profitability without having to train operations and management staff into expert MR™ practitioners to successfully achieve the desired results.CITATION:Dunne, A, Laurens, P G, Kruger, R and Coleman, H, 2015. Optimising flow in the mining value chain, in Proceedings Iron Ore 2015, pp 437–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016