Search Documents

By J. J. Jakosky

THE fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.1 One of the most impor-tant measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtain-ing bottom-hole data. The applications of bottom-hole pressure or fluid-level measure-ments are based on simple hydrodynamic principles. Under equilib-rium conditions, pbh = hd + pg + pch [ l] when pbh = bottom-hole pressure, lb. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, lb. per sq. in. per foot, pg = weight of section of gas column 1 in. square from fluid level to casing head, pch = casing-head pressure, lb. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casing head plus the casing-head pressure. At moderate rates of flow, the rate of production is approximately proportional to the difference between the reservoir, or static bottom-hole, pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

By Eugene Coste

ALTHOUGH some of the observers who first paid especial attention to the occurrences of oil and gas in the strata (such as Hunt in 1859, Andrews in 1861, Winchell in 1865, Mendelejeff in 1876, Höfer in 1876, Minshall in 1881, and I. C. White in 1883) seem to have been impressed with the fact that oil and gas deposits were connected with the disturbances in the rocks caused by their upheaval,1 yet, with the exception of Mendelejeff, and possibly Andrews, these observers do not appear to have understood what is really the one essential factor in the occurrence of oil and gas in the strata: viz., the faulting, uplifting, fracturing, fissuring, and jointing always accompanying even slight rock disturbances, and in certain districts (petroliferous provinces)2 allowing solfataric hydrocarbon emanations to force their way up from the interior and to reach and impregnate the porous portions of sediments subjected to the disturbances. Instead of this simple explanation to account for the observed connection between petroleum deposits and rock disturbances, most of the observers mentioned above, and many others who have followed them on the name lines since, have entirely reversed the problem. To them, instead of the dissemination of gases from fissures into the sediments, it presented the accumulation and concentration, according to anticlinal or other geologic structures, of oil and gas originally present throughout the whole mass of the strata where they were produced by the decomposition or distillation of organic remains. Whether this important problem involves accumulation from sources within the oil-bearing strata themselves, or infiltration and dissemination from outside sources, may be easily determined if all preconceived ideas are put aside and the established facts only are considered.

Jan 9, 1914

By A. T. Shurick

THE present economic crisis in bituminous coal is substantially the most insidious, and critical, in the modern history of the industry. The large consumption deficit that has gradually developed (almost unawares), has culminated in a situation that has forced home the urgent necessity for prompt and radical remedial measures, such as the various mergers now in course of negotiation. Conditions today are sufficiently comparable with those in the iron and steel industry, preceding the formation of the United States Steel Corpn., to suggest the possibility of a sweeping super-consolidation, that all but staggers the imagination. The important function of the banker in this, and lesser projects, is too well known to require comment, and it is important that we understand clearly just what these functions are. Certain features in banking practice came up for consideration in connection with a rather exhaustive economic study into the prospective future of the coal industry, upon which I was recently engaged for an Eastern bituminous interest. This survey was made for the purpose of effecting a decision on certain pressing questions of policy, involving considerable capital expenditures, that would be compatible with the flattening out in the curve of production in recent years. An examination of the TRANSACTIONS, and the coal literature generally, failed to disclose any pertinent, and authoritative data, on this subject. This was more or less characteristic of the whole survey, which had involved a large amount of original research, and measures were taken to procure the required information. The following notes have been compiled largely from the data thus collected, supplemented with material, suggestions and criticisms, by several of the larger banking houses active in coal, together with personal memoranda of my own.

Jan 1, 1928

By M. C. Leverett

The behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petroleum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,' and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed primarily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations: Ko = PA6A [la] and Ku = Q [lb] In order to put the results obtained on a comparable basis for different sands, the effective permeabilities will be stated as fractions of the normal permeability of the sand; i.e., fractions of its permeability to a homogeneous fluid. Algebraically, these fractions are: KO' = Ko/K, and KWr = K,/X [2a] and [Zb]

Jan 1, 1939

By Thomas D. West

The fact that iron expands when heated, until fusion takes place, and that molten iron is consequently less dense than solid iron of the same grade, is now universally admitted. It was proved by the extensive experiments of Mr. Thomas Wrightson, reported in the Jownal of the Iron and Steel Institute (1890, No. 1, p. 72, and 1891, No. 1, pp. 75, log), and, in a manner, is illustrated in heavy founding by the shrinkage 'of the molten metal, which must be " fed " in order to obtain solid castings. This decrease in volume requiring " feeding" while the metal is still liquid I call " shrinkage," applying the term " contraction" to the decrease in volume which takes place after solidification, while the iron is cooling to atmospheric temperature. The light-work founder, not having the opportunity to make heavy castings, in which shrinkage can be observed, is apt to confound the two; but they are in fact distinct, and are separated by an act of expanion, which takes place at the moment of solidification. The fact of this expansion was first practically demonstrated by Mr. John R. Whitney, of Philadelphia, Pa., whose experiments are recorded in the National Car and Locomotive Builder of May, 1889. Experiments recently made by the writer indicate that there is a constant relation between this expansion and the preceding shrinkage and forcibly demonstrate the necessity of " feeding " a casting to make its interior solid. This is a matter with which all makers and users of castings have experienced difficulty. The founder being heretofore unable to define correctly the principles involving the urgent necessity of " feeding " has failed to impress the moulder with its importance in making sound castings.

Jan 1, 1897

By M. C. Leverett

The behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petroleum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,' and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed primarily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations: Ko = PA6A [la] and Ku = Q [lb] In order to put the results obtained on a comparable basis for different sands, the effective permeabilities will be stated as fractions of the normal permeability of the sand; i.e., fractions of its permeability to a homogeneous fluid. Algebraically, these fractions are: KO' = Ko/K, and KWr = K,/X [2a] and [Zb]

Jan 1, 1939

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The early mining of iron ore in Minnesota was carried on with the most primitive kind of tools. The pioneers used only such equipment as could be packed from Duluth through one hundred miles of forest to the first mines on the Vermilion Range and the operations were carried on with picks, shovels, hand drills and wheelbarrows, the ore being hoisted in buckets with a horse winch and carted in horse drawn wagons to the stockpile. This was about the extent of the mechanical equipment of the Minnesota iron mines in the early eighties.As soon as a railroad was pushed through from Two Harbors to the Vermilion Range the equipment began to be improved upon; wood burning steam boilers were installed and small steam puffers displaced the horse-winches, wheelbarrows were aban¬doned and small cars were introduced. Hauling the hoisted ore in wagons was discontinued and trestles were built so that the ore could be stockpiled more cheaply through the use of cars and high piles. These same stockpiles were loaded by hand into the 10 and 15 ton capacity railroad ore cars.Within a few years a marked change took place—the hand drill gave place to the air drill, such as No. 3 Rands, Ingersolls, Sargents and some Sullivans. Tramming was done by mules, the ore hoisted in. self-dumping skips, hoisting engines were intro¬duced and it seemed as though mining as a business in Minnesota had come to stay. At this stage someone conceived the idea of making the stockpile floor about three feet above the top of the ore cars to facilitate the hand loading of stockpile ore for trans¬portation. This was done through the use of wheelbarrows at first and later by using I-ton cars running on tracks laid on the stockpile floor."

Jan 1, 1920

By Waldemar Lindgren

I. INTRODUCTION AT the time of the discovery of America the old world had a scant supply-of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the nines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia and some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon wade the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 4, 1916

W. ROWLAND Cox,* New York, N. Y. (written discussion?).-The process described by Mr. Malcolmson undoubtedly represents a great stride toward conservation of our natural resources. Without discussing the subject from an economic standpoint, I wish further to emphasize the fundamental principles of the Smith process in order that its economic value may be fully appreciated. The process is essentially a means of producing an ideal fuel, as regards its combustion qualities, by the removal of the so-called volatile matter from the coal, in the form of byproducts, which have value for other purposes far in excess of their fuel value. In other words, coals which contain. large amounts of gas, tar, and ammonia, and are not suitable for domestic or industrial fuel, or for treatment in byproduct coke ovens or gas retorts; because they possess poor coking qualities, can he prepared for commercial use by the. Smith process with a very high degree of efficiency. Much work has been done along this line, both in this country and in Europe, in developing a means of preparing coal, as the economic advantages have long been recognized. To the best of my knowledge, the Smith process is the only one that has proved its commercial adaptability. Distillation of coal at 900° to 1000° F. (480° to 540° C.) yields a large amount of tar and oils. The residue of the distillation, however, is a very friable semi-coke, wholly unsuitable for use as a fuel, unless it can be charged directly into a byproduct gas producer. The problem which confronted the inventor was then to convert this carbon residue into a commercial product, and it is in this step that the Smith process has overcome the obstacles which prevented a number of other methods from becoming commercially practicable.

Jan 10, 1918

By George F. Becker

Complexity of Rock-Fractures. - The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible node of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is, how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints. - It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings, often called joints. These partings are frequently flat surfaces, even when seen in very large exposures, but are sometimes surfaces of moderate single or double curvature. Joints usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in I hand-specimens as mere slaty cleavage consists, in reality, of innumerable microscopic faults. For this reason, Mr. Daubrée rejects the term "joint," as failing to imply the existence of relative motion, and has introduced the terms “diaclase” and “paraclase” as substitutes.1

Jan 1, 1913

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.' It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

By J. E. Pogue

It is the purpose of this paper to attempt to establish three theses which may be stated in advance as follows: 1. The crude oil potential is the accumulation of surplus initial production. 2. The crude oil potential is a semi-inventory and therefore is a causal factor in the price of crude petroleum. 3. The price of crude petroleum no longer correlates with above-ground inventories but does correlate with corrected inventories (i. e., above-ground storage plus the inventory equivalent of the crude oil potential). The factors and principles set forth in this study are thought to yield an approximate answer to a number of questions of active interest in the petroleum industry today, to wit: (a) How long would be required to eliminate the potential if all drilling ceased? (b) What would be the indicated crude oil production of the United States in 1931 if proration were abandoned? (c) What economic change would be necessary to warrant a higher price for crude oil? Definitions For the purposes of this study the following definitions may be stated: The crude oil potential in the United States is the quantity of oil that all the oil wells would make the first 24 hr. if permitted to flow unrestricted. The surplus potential is the above-mentioned quantity minus the volume currently produced. Initial production is the first day's unrestricted flow of an oil well. Aggregate initial production is the sum of the initials of all wells completed during a year. Surplus initial is the initial not needed to bring production into balance with demand. The surplus initial is equal to the crude oil potential minus the current rate of production. The annual production-equivalent of the crude oil potential is the volume of oil that would be produced in one year if all wells were permitted

Jan 1, 1931

By Hamid Maleki

Rock mechanics models are “data-limited,” i.e., one seldom knows enough about a rock mass to use computational models unambiguously. Statistical methods, however, are capable of being applied where there are good data but a limited understanding of certain natural phenomena, such as the creep of rock salt or elevated risk domains associated with violent failure of strata commonly referred to as coal bumps and coal bursts. Important to these evaluations are (1) having statistically valid data collected consistently and (2) incorporation of analytical calculations for quantifying geologic, mining and particularly geotechnical variables. By combining the strength of the statistical and analytical models, an improved “hybrid” model is created and utilized. To demonstrate the use of hybrid statistical-analytical techniques in rock mechanics problems, three case studies are used. The first case study involves a historic examination of a nuclear waste repository in rock salt, where mathematical models are built using excavation con- vergence data to identify significant variables and estimate future deformation and stability. This case study uses the convergence rate at up to 121 locations of different ages and geometries using monitoring data over the facilities' footprint excavated through 1998. The second case study focuses on ongoing analysis of coal burst mechanics and associated factors. Within the last three decades, a hybrid statistical-analytical methodology has been applied for identifying significant factors affecting coal bursts. This final hybrid model utilizes data from 30 case studies from Utah, Colorado, Kentucky, and other Eastern U.S. mines providing predictive capability for the entire United States coal fields. The last case study is the assessment of Castlegate Sandstone escarpment stability using historic data collected over 17,000-ft of sandstone escarpment exposure in the vicinity of longwall operations in Utah. Results from all three case studies are used for demonstrating the utility of the method in solving ground control problems.

Jun 25, 2024

By J. Slivnik, A. Stergarsek

[The site] [Z]irovski vrh uranium ore deposit is located in the extreme north-western part of Yugoslavia, some fourthy kilometers from the capital of Socialist Republic of Slovenia, Ljubljana, not far from the Italian and Austrian border. The sandstone type deposit of uranium ore with medium grade is located in a foothill of Julian Alps. The site shows some typical conditions for this region, which demand special attention in respect to the incorporation of an uranium treatment facility into environment. Among these specific conditions the following site characteristics should be mentioned: - populated area of agricultural and recreational value, - unconvenient climatic conditions with excessive rainfall and long lasting temperature inversions in the winter time, - very pure surface and underground waters which supply the drinking water reservate for large area including the capital of Slovenia, - sharp relief, - unconvenient geological structure. The choise of technology The intention to produce uranium and at the same time respecting the natural characteristics and existing uses of the site made the design of the ore treatment facility relatively difficult one. In general, there were two basic alternatives available perform the task. First alternative was to adopt the usual technological flowsheet with wet tailings disposal and with discharge of used water i.e. liquid effluents into the river. In order to prevent the negative impact of such technology on the sourrounding area sophisticated water purification installation and costly measures in wet tailings disposal e.g. impermeabilisation of large areas by concrete injections, large dam constructions, uncertain capturing of the water sources should be employed. Second alternative was to modify the usual flowsheet by employing the maximal recycling of liquid effluents to the process and to dispose the solid

Jan 1, 1980

By H. V. Winchell

An examination of the Pachucal and El Oro districts in July, 1920, although cursory and incomplete, disclosed facts of more than passing interest to the student of ore deposits; and inasmuch as the literature on these districts is limited and some of their features are little understood, a brief account may prove valuable as reconnaissance observations to be amplified by more thorough and competent observers in the future. Where no complete monograph of important mining camps has been published a partial presentation of the data is often useful, as it sometimes leads to fuller and more accurate descriptions, by stimulating discussion. The following notes are presented with the consent of A. F. Main, managing director of the El Oro Mining and Railway Co., whose fund of information and wide acquaintance with both districts alone made it possible to cover so much ground in a short time. I have also to acknowledge gratefully the aid of C. A. Lantz and D. S. Calland of the Santa Gertrudis and Real del Monte companies, respectively, in connection with permission to inspect geological features of interest in their mines. Pachuca, Hidalgo, Mex. This mining camp has been described by Ezequiel Ordonez2 and by A. F. J. Bordeaux.3 Reported to have been discovered in 1522, it has produced silver valued at between $250,000,000 and $375,000,000. Subsequent to the discovery here, by B. de Medina, of the patio process. in 1557, its production was increased, and now, using cyanidation, the output of the camp is nearly one-sixth of the production of the world. Topography and Climate The Pachuca district consists of a series of mountains and valleys, the minor features of which extend in an easterly and westerly direction and reach elevations of 8000 to 10,000 ft. (2438 to 3048 m.) above the

Jan 1, 1922

By Robinson Leon-Diaz, Alberto Jaen-Toribio, Raymond Blanchard, Mike Deevy, Miguel Fuentes-Llanos

"Tunnels designed to NFPA 502 are required to withstand the RWS time-temperature curve, more specifically prevent progressive spalling and loss of strength of steel reinforcement. Fire boards or spray-on layers can be effective, however, these solutions have capital and whole-life cost implications. The use of “fire resistant” concrete based on a suitable aggregate with polypropylene fibers has also increased in recent years. This article presents a new methodology for thermal and structural analysis of segmentally lined tunnels, which permits the analysis of project specific fire curves and an assessment of different fire protection strategies. The effectiveness of fire boards is assessed along with whether “fire resistant” concrete alone is a viable means of achieving the required protection. Finally, since NFPA 502 recommends water-based fixed fire-fighting systems for Category C and D tunnels, we discuss the question of how a fixed fire-fighting system should be addressed within the structural design. INTRODUCTION Protecting road tunnels from structural damage and collapse is a key requirement for both life safety and business continuity. Where road tunnels are part of key highway corridors, protecting business continuity is a high priority for owners, operators and the Authority Having Jurisdiction. For existing tunnels, compliance with NFPA 502 may require upgrades with either passive fire protection and/or water-based fixed firefighting systems. For new tunnels, compliance with NFPA 502 requires a combination of good practice in design and fire testing. A water-based fixed firefighting system is a Conditionally Mandatory Requirement1 for Class C and D tunnels, i.e. all tunnels greater than 300m and 1000m long respectively. The basis for fire safety design of new tunnels and assessment of existing tunnels is the worst-case fire scenario. A number of factors, including but not limited to the following, influence this design fire scenario:"

Jan 1, 2016

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, M. Zare

High Pressure Grinding Roll (HPGR) plays a major role in increasing specific surface area of iron ore concentrate for producing pellet feed. HPGR grinding mechanism implies that material be compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study for determining a simple relationship between material pressure resistance ability and HPGR main design parameters, piston press tests were performed on different iron ore concentrate samples along with HPGR Blaine increasing tests. Piston press tests results showed that by decreasing moisture content, material pressure resistance increased and in constant moisture content this parameter will change based on material specifications. HPGR Blaine increasing tests results showed that by decreasing moisture content, HPGR specific throughput and working gap increased and in constant moisture content this parameter will change based on material specifications. For all of the studied samples at worst condition, we got the results including: HPGR delta gap equal to zero, specific throughput lower than 200 ts/hm3.According to the tests results, HPGR Applicability Index (HAI) can be introduced at four different class types from 1 (weak) to 4 (excellent). This index determines achievable specific throughput and possibility of using HPGR according to material specifications, i.e. for HAI 1-4 the pressure resistance is <90, 90 to<125, 125 to <150 and = 150 bar, respectively. Similarly for HAI 1-4 specific throughput is <200, =200, =220 and =250, respectively. So based on design moisture content, if concentrate HAI is 3 or 4, HPGR is a correct choice. For HAI 2, HPGR can also be used. But for a material with HAI equal to 1, HPGR is not a good solution. As a result in order to apply HPGR for HAI 1, material condition such as moisture or slime content should be decreased.

Jan 1, 2018

By A M. Myrvang, B Nøst, N Q. Trinh, I S. B Bergh

The iron ore producer Rana Gruber AS is situated in northern Norway just below the Arctic Circle, and has been producing hematite and magnetite concentrates for more than 60 years. Since the late 1990s, the major part of the production comes from a sublevel stoping underground operation after many years of open pit mining. Despite moderate mining depth, the operations have experienced considerable rock stress problems due to quite high tectonic, horizontal stresses. To manage the problems, comprehensive rock mechanics investigations have been carried out by SINTEF, a major contract research organisation. This has included in situ rock stress measurements, laboratory investigations and numerical modelling. Based on this and practical experience, satisfactory design of vertical and horizontal pillars was achieved. At depth, the ore width increases from 30–40?m to more than 100?m. This, together with a major planned increase in production, called for a change of the mining method. After thorough investigations and considerations, it was decided to change to sublevel caving, very much like the LKAB system. The development of the new system has been closely followed up by rock mechanics measures, including 3D numerical modelling and comprehensive monitoring of deformations and rock stress changes. To achieve a satisfactory caving of the hanging wall, all vertical and horizontal pillars in the sublevel stoping area had to be removed. This has been a challenging task, and the development of the caving has been slow until recently. However, now the caving develops satisfactorily.CITATION:Bergh, I S B, Trinh, N Q, Myrvang, A M and Nøst, B, 2014. From sublevel stoping to sublevel caving at Rana Gruber, Norway – rock mechanical aspects, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 323–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

1. Introduction This document represents Part II of our final report on the development of a "Remote Sealing System for Extinguishing Coal Mine Fires. " It is a technical report which summarizes the results of system development and field demonstration. Part I of this two - part final report is an Operator&apos;s Manual for the application of the Remote Sealing System to a coal mine fire. 1.1 Background When coal mine fires go out of control and can no longer be fought directly, the standard fire fighting technique is to construct air-tight seals in the mine passages leading to the fire area so&apos;--,that the oxygen supply to the fire is". cut off. Ultimately, it is desirable to isolate the fire zone in such a way that normal operations can resume in the remainder of the mine. The construction of seals in the- mine causes the atmosphere to pass through a toxic and explosive phase. Explosions, if they occur, are not only hazardous to the men working at the sealing operation, but can also undo much of the sealing work which has already been accomplished. Sealing of passageways surrounding the fire zone from within the mine is extremely difficult and dangerous. Methods for direct sealing are detailed in "Control of Mine Fires&apos;. 1 An alternative to this approach is the technique of remote sealing. This involves drilling boreholes which intersect the mine passages at the locations where the desired seals are to be constructed. The seals are then constructed by pouring material down the borehole and filling a segment of the passage from bottom to top. During this operation, there are no personnel in the mine, all operations taking place on the ground surface.

Jan 1, 1973