Search Documents

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989

This paper is a tribute to the late Dr Donald Martin Hausen as a father of applied mineralogy. His dedication to promoting the field through technical societies and through his professional work was outstanding, and his activities as a humanitarian are noteworthy. Dr HausenÆs involvement in technical societies included organising and conducting the only ICAM congress that was held in the USA, co-founding and nurturing the Process Mineralogy Committee within the American Institute of Mining, Metallurgy and Petroleum Engineers, and participating in CAM, the International Mineral Processing Congress, as well as other technical societies. The Process Mineralogy Committee that he co-founded has continuously organised annual meetings in the USA by conducting a series of sessions, and 17 books on the proceedings from those sessions have been published. As an applied mineralogist Dr Hausen solved many problems in exploitation and processing of minerals, metals and materials, especially gold. He helped to find many Carlin-type gold orebodies by outlining targets using alteration halos as determined by X-ray diffractometry, and he defined mineral characteristics that affected gold metallurgy and cyanidation. It is also noteworthy that Dr Hausen and his wife, Mary, opened their arms and home to many foster children and were instrumental in their placement in many homes. They also sponsored refugees from south-east Asia, taught them English, housed them, and provided constant support until the refugees became responsible and independent US citizens.

Jan 1, 2008

By P. W. A. Walker

"The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.216% W03 and 0.020070 Mo. The deposit is uneconomic at current tungsten prices. IntroductionDuring the 19705, Union Carbide Corporation was a major producer, processor and supplier of tungsten and derivative products to end-user manufacturing industries. The corporation owned and operated two tungsten mines in the United States, and one in Brazil, and operated a plant in the United States which produced ammonium paratungstate (APT) which is an intermediate product in the production of tungsten wire and tungsten carbide for cutting tool insets and hard facings. In 1975 the three mines were ageing with short-life reserves and high production costs. The world market for tungsten was buoyant and prices, in constant dollar terms, had risen steadily over the past 15 years (Fig. 1).It was against this background that a decision was made to explore for tungsten in North America, South Mrica, Australia and Brazil."

Jan 1, 1994

By Sturgul J. R

The South Middleback Ranges (SMR) operation involves the develop- ment of iron ore resources at the Iron Duke mine in the South Middle- back Ranges to replace the Iron Baron mine whose reserves are nearing depletion. The Iron Duke mine will be developed by contract to the stage where it can continue operation at full production when Iron Baron is closed. As part of the mine planning of the operation a GPSS computer simulation model was written to determine equipment requirements. The model simulated the operation of the mine with trucks transporting ore and waste to the appropriate destinations and producing a blended product in the stockpiles. A loader and two trucks would transport ore from the stockpiles to the crusher for one shift per day. The simulation shut the operation down at crib, morning tea, shift change and weekends, and also on the third shift each day. It also modelled operating delays. The results gave equipment operating hours and total output of each material type. The model was modified to produce different outputs from the mine and could be used to determine the most productive shift arrangement.

Jan 1, 1989

The Colorado Scientific Society, Denver, Colo Charles Henderson, President, 519 U. S Custom House, Denver, Colo. Beginning in 1882, up to. about 1919, the Society published 11 volumes containing many valuable papers From the informa¬tion at hand, the papers in those volumes are now only available in libraries or on file at institutions. Vols 12 and 13 are the current volumes, and the list of the geologic papers contained in them are given here For any information as to price and availa¬bility, address the above. Vol 12 (1929-31) No 1, The geology of the Sangre de Cristo Mountains, by J H Johnson, 2, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by B S Butler; 3, Mosquito Range and the Leadville district, by C H Behre, Jr , 4, Geologic history of the Front Range, by T S Lovering, 6, Revision of geologic structure and stratigraphy in the Ouray district, by W S Burbank, 7, Localization of ore in the schists and gneisses of the Mineral Belt of the Front Range, by T. S. Lovering, 8, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by J. B. Tenney; 9, Preliminary geologic map of the Alma mining district, by Q D. Singewald and B S Butler, 10, The Climax molybdenum deposits of Colorado, by B S Butler and J W. Vanderwilt, 12, Localization of ore bodies at Rico and Red Mountain, by G. F Collins, and Geology of Mount Lincoln and Russia mines, by Q D Singewald and B S. Butler. Vol 13 (1932- ): No. 1, Preliminary geologic notes on Galena Mountain, by J. W Vanderwilt, and High plains of Colorado and New Mexico (Late Tertiary history), by F. M. Van Yuyl and J M. Coke

Jan 1, 1933

Upon subduction, water is liberated from the sediments and the porous struc- ture of the oceanic crust and from de- hydration of minerals for redistribution and chemical reaction. A survey of pro- cesses which are likely to occur along the subducting plate reveals that water may well be basic in subduction induced gas generation, magma formation and ore deposition. In analogy to the industrial water gas process, reaction of water with car- bonaceous matter, in subducted sediments is likely to yield substantial volumes of hydrogen and carbon dioxide. While water and carbon dioxide appear to play a determining role in the development of differentiated magmas, hydrogen will react with metal sulfides and sulfur to form hydrogen sulfide which is essential in sulfide ore depo- sition. A survey of possible metal extrac- tion chemistry along subduction suggests a stepwise solubilization of metals from sediments and oceanic crust, and a poten tial accumulation of dissolved metals in zones of characteristic composition. The metal spectrum in ore deposits at near surface appears to reflect the com- position of the solution in the respec- tive subduction zone. A tendency for preferential solubi- lization of copper at subductidn level, from among the transition metals, an in- creasing generation of hydrogen sulfide in the sane direction and partition effects as well as sulfide precipitation characteristics lead to enrichment in copper and to its selective deposition in the direction towards the trench as observed in S. Latin America. A postscript deals with the formation of native copper.

Jan 1, 1986

By William L. Zeller

IN the past 75 years industrial engineering has been highly developed in many fields, but the coal mining industry has just begun to realize its potential for cutting costs. To receive the maximum benefit, a company should apply industrial engineering from the time a new installation is contemplated, but the principles can also be used to reduce and control the costs of an established operation. One company that had been mechanized for seven years reduced its total labor cost 57 pct by industrial engineering. Of this reduction, 20 pct was brought about by a preventive maintenance, rebuilding, and scheduled lubrication program that eliminated 80 pct of the delay caused by mechanical and electrical failures. Thirty percent of the cost reduction was attributed to rearranging the work force into crews of the most effective size, changing working methods, and training all mine supervision in the principles of the cost reduction program. The remaining 7 pct reduction was brought about by a wage incentive program for all the men in the mine. The productivity of this coal mining operation was increased from less than 8 tons per payroll man to 20 tons. This increased productivity was brought about while using the same equipment, men, and supervision.

Jan 12, 1957

By D. Moradkhani

The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. The main purpose of this study was to extract copper from the copper low-grade oxide ore of Chodarchaei mine using column leaching. The copper oxide ore contained 1.1% Cu and 1.75% Fe. The mineralogical analysis indicated the malachite (Cu2(OH)2CO3) was mainly composed of oxidized phases. The sulfuric acid leaching experiments were performed under the laboratory conditions. The influence of several parameters on the course of the reaction such as particle size, acid concentration, flow rate, and time was examined. The optimum collective extraction of copper and iron was obtained at a particle size of +10-15 mm for a leaching duration of 3 days with sulfuric acid concentration of 100 gpl and using a flow rate of 2.5 cc/min. Under these conditions, the recovery of copper and iron were 98.54% and 41.99%, respectively. Keywords: column leaching, copper, iron, working diagram.

Sep 1, 2012

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By W. X. Yin

Electrowinning of lead from aqueous solution of PbCl2 and electrowinning of manganese dioxide from aqueous solution of MnCl2 are two research focuses in hydrometallurgy. This paper investigated a new process of simultaneous electrowinning of lead and manganese dioxide in chloride medium. The simultaneous electrowinning process in chloride solution not only can prevent chloride from liberating at anodes but also obtain two electrolysis products and decrease electric energy consumption. Diaphragm cell is used in the simultaneous electrowinning process to form separate anode and cathode compartment. The effects of temperature, HCl concentration in anolyte, NaCl concentration in catholyte and electrolysis time on current efficiency and cell voltage are studied. The results indicate that current efficiency of anode and cathode for 5 hours is 99% and 96% respectively, average cell voltage is 1. 701V, the weight ratio of lead and manganese dioxide produced at electrodes is 2. 39:1 under the optimum conditions. As anode products, manganese dioxide is ??MnO2, content of which in the products is more than 92%.

Jan 1, 2014

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By Arlindo Lopes Faria

O Drop Weight Tear Test (DWTT) é comumente empregado para avaliar a capacidade de um material impedir a propagação de fratura frágil na temperatura de projeto. Esse ensaio quando aplicado a aços modernos de elevada tenacidade, produzidos via resfriamento acelerado, para aplicação em dutos, pode não exibir o mesmo comportamento à fratura dos aços convencionais, por apresentar um tipo de fratura anormal, denominada fratura inversa. Esse tipo de fratura, por sua vez, invalida os resultados de DWTT segundo os critérios estabelecidos pela API RP 5L3. Neste trabalho, são apresentados os resultados obtidos em ensaio de DWTT, utilizando corpos de prova full-size e sub-size, de um aço de elevada tenacidade, produzido com distintas condições de processamento termomecânicas evidenciando o fenômeno de fratura inversa. De uma forma geral, observou-se uma correlação entre os resultados de DWTT e as propriedades mecânicas em tração. Os testes também apontaram que a geometria do corpo-de-prova (full-size ou sub-size) possui uma influência direta no resultado do ensaio de DWTT.

Aug 16, 2017

By F. Warnaars

Historically, this area produced gold and silver from many well-known vein deposits, like Tayoltita, Topia, and San Jose de Gracia. Modern exploration identified three categories of deposits: 1) low grade porphyry golds in shallow level dacite porphyries; 2) batholith-related deposits; and 3) those formed in volcanic sequences of Late Cretaceous to Late Tertiary. At least four porphyry golds have been identified, of which Metates is best known. These are formed by and within dacite porphyries, associated hydrothermal breccias and sometimes within surrounding metasediments. Their ages are from mid-Cretaceous to Early Tertiary. Precious metal deposits associated with batholiths occur as veins, contact haloes in metasediments or volcanics, skarns, tectonic breccias, hydrothermal tourmaline breccias, dacite dikes or as disseminated or stockwork deposits such as La Fortuna. Several new gold discoveries were made in older Early Tertiary Volcanic Sequences and in the younger Tertiary volcanics within prominent structures exceeding 3 to 5 km in lengths. Some of these are open-pittable but most have to be mined by underground methods.

Jan 1, 1999

By Breno Totti Maia, Rubia Teodoro Silva, Daniel A. G. de Carvalho, Aline Lima da Silva, Gilvan Nascimento de Souza

Para a maior eficiência na técnica conhecida como Slag Splashing, empregada com fins de manutenção e reparo de refratários de convertedor LD, a escória deve apresentar características apropriadas em termos de viscosidade e fração de sólidos. No presente trabalho, desenvolveu-se uma metodologia híbrida, combinando a utilização de padrões para a caracterização visual de escórias na planta, baseada em critérios de atribuição de notas, com a simulação termodinâmica usando o software FactSage para determinação das fases presentes na escória, quantificação de fração de sólidos e cálculo da viscosidade efetiva. A metodologia proposta permite identificar os quadrantes ideais de viscosidade efetiva, fração de sólidos e teor de ferro total, de modo que se possa garantir escórias com notas altas, apresentando qualidade apropriada para o processo. Os resultados indicam que as escórias com nota 3 (ótima) são obtidas nas seguintes condições: temperatura de fim de sopro de 1690-1720ºC, viscosidade efetiva na faixa de 0,070-0,650 Pa.s, fração de sólidos de 13-22%, teor de ferro total na escória de 14-17,5%..

Oct 1, 2019

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975