Search Documents

By V. M. Dobrynin

Experimental data demonstrate that physical properties of porous rocks change under pressure. In this paper an assumption is made and proved that under pressure the changes of physical properties such as porosity, density, permeability, resistivity and velocity of elastic waves are controlled to a large extent by the pore compressibility of rocks. It is also shown that the pore compressibility of rocks can be determined, within the range of pressures from 0 to 20,000 psi, by knowing the maximum pore compressibility and the magnitude of the pressure. Mathematical equations were developed which permit one to define changes in physical properties of porous rocks under pressure. These equations were verified by experimental data obtained from the study of sandstones. INTRODUCTION In studying the behavior of porous rocks under pressure in the field of petroleum technology, the most interesting aspect is the observation of those properties which characterize the rocks as possible reservoirs — for example, porosity, permeability, resistivity, density and the velocity of elastic waves. The literature dealing with this problem mainly contains data concerning the study of only one or at most two of these parameters, but not of the group as a whole. An attempt is made in this paper to find general equations involving each of these parameters, which will permit the study of the behavior of rocks under pressure. All experimental data used here were obtained from the investigation of consolidated sandstones. EXPERIMENTAL In addition to the use of published experimental data, an experiment was carried out which studied the main physical properties of sandstones under pressure. Two homogeneous quartz sandstones were chosen for this purpose: (1) the Torpedo sandstone from Kansas, and (2) the Medina sandstone from Ohio. The porosity of the Torpedo sandstone was 20.2 per cent, and that of the Medina 8.7 per cent. Permeabilities were 45 md and less than 1 md, respectively. Each sandstone contained about 5 per cent clay minerals, consisting mostly of kaolinite and chlorite, which were distributed quite evenly throughout the samples. One cylindrical sample 2 in. in diameter and 5 in. in length was cut from each sandstone and then saturated in a vacuum with a 3N solution of NaC1. This high concentration was used in order to obtain true formation factors and to decrease the swelling of the clay minerals. The methods of mounting the samples and measuring the changes in porosity and resistivity were practically the same as those described by Fatt and Mann.1,2 Changes of resistivity under pressure were studied for sandstones with 100 per cent water saturation, and for sandstones with the irreducible water saturation. The irreducible saturation was obtained by enclosing the saturated rock samples in relatively fine silicate powder so as to remove the water by capillary action. This procedure is described by Orkin and Kuchinski.3 Changes of permeability with pressure were determined at room temperature using nitrogen as the flowing medium. In studying the effects of pressure, one series of measurements was made using an internal pore pressure Pi equal to the atmospheric pressure, while the overburden pressure Pe ranged from 0 to 20,000 psi. A second series of measurements was used over the same range of overburden pressure, but with an internal pore pressure of 1,800 psi. When the results were compared on the basis of net overburden pressure (Pe — 0.85 Pi ), there was practically no difference for these two sandstones. The origin of the factor 0.85 in the expression for net overburden pressure is given by Brandt,4 Fatt5 and Geertsma.6 The relatively large bulk volumes of the sample (about 15 cu in.) made it possible to observe a

By C. R. Simcoe, T. J. Koppenaal

The effect of direct and alternating currents on the quench aging behavior in an Al-4 pct Cu alloy has been investigated by use of resistivity measurements. The reaction rate increases with direct current density in the investigated range of 1000 to 3000 amps per sq cm. Alternating current of a specific frequency is observed to decrease the reaction rate by a factor of about two. ErDMANN-JESNITZER et al.,1,2 investigated the effect of direct and alternating current on the quench and strain aging behavior of low-carbon iron. In both cases they observed that direct current accelerates the aging reaction and that an alternating current can completely inhibit the aging process. The purpose of the present research was to investigate these phenomena in the quench aging behavior of an Al-4 pct Cu alloy and to determine the correlation, if any, between the increase in the observed reaction rate and possible heating effects accompanying the aging with direct current. EXPERIMENTAL PROCEDURE The aluminum-base alloy used in this investigation contained 3.98 wt pct Cu (1.72 at. pct) with impurities of 0.003 pct Si, 0.002 pct Fe, and 0.001 pct Mg. The alloy was rolled into a ribbon about 0.36 mm thick and 3.7 mm wide. The ribbon was split end from end with the ends being used as electrical contacts and the central unsplit section, about 5.3 cm in length, serving as the specimen. Solution treatment was accomplished by quenching from a salt bath at 520° ± 2°C into water at 25° ±0.5°C; the specimen was immediately transferred to a liquid nitrogen bath. All aging was done at 75° ± 0.2°C in a rapidly stirred ethylene glycol bath. Resistivity measurements were made by the double potentio-metric method employing a standard resistor; for purposes of convenience, the resistance measurements were made at 77°K. The transfer of the specimen from the aging bath to a liquid nitrogen dewar was accomplished in less than 1 sec. The aging kinteics were studied with the specimen being aged under the influence of direct current, alternating current, and without any type of current. The amount of heating caused by direct currents was investigated by soldering a thermocouple on the specimen surface and measuring the temperature change after applying various current densities. The temperature was observed to increase (from 75°C, the aging temperature) about 0.8°, 3.0°, and 8.5°C with direct currents of 1000, 2000, and 3000 amp per sq cm, respectively. When employing alternating current, the circuit was monitored with an oscilloscope and adjustments made to produce a normal sine-wave pattern. RESULTS Prior investigations3'4 in the aging characteristics of A1-4 wt pct Cu have shown that the resistivity initially increases, reaches a maximum, and then decreases to values significantly lower than the as-quenched resistivity. This type of behavior is seen in Fig. 1 which shows the resistivity at 77°K as a function of aging time at 75°C observed in this investigation. At this aging temperature, the resistivity maximum is seen to occur in about 1 to 1-1/2 min and it further decreases to the as-quenched value in about 24 min. The behavior observed with the application of direct currents of 1000, 2000, and 3000 amp per sq cm during aging is shown in Fig. 2. With increasing current densities, (+) ?pmax decreases and the rate of the aging process increases. The time necessary to reach the as-quenched resistivity value decreases from 24 min for aging without current to about 16, 10, and 7 min for aging with 1000, 2000, and 3000 amp per sq cm direct current, respectively. Fig. 3 shows the results obtained when two changes were made during the aging with 2000 amp per sq cm

Jan 1, 1963

By C. M. Trigg

"PEC uranium deposit, 100 km southwest of Coppermine, was discovered by diamond drilling in 1976 following ground and airborne geophysical surveys, geological mapping, geochemical surveys and boulder prospecting that were initiated as the result of the discovery of uraniferous sandstone outcrops in 1969 by geologists of Aquitaine Company of Canada Ltd.The deposit is within gently northeasterly dipping medium to coarse-grained Unit 11 quartzitic sandstone of Neohelikian Dismal Lakes Group. The deposit is from 10 m to 70 m above the base of the sandstone which, beneath the deposit, non-conformably overlies weathered and altered Aphebian granite of Great Bear Batholith or unconformably overlies rubble breccia, conglomerate and medium-grained Unit 8 sandstone of Paleohelikian Hornby Bay Group.A northeasterly trending, 500 m wide graben, bounded by the steeply dipping northeasterly striking Imperial and Aquitaine faults, contains the deposit which is 1.1 km long by up to 340 m wide. The deposit overlies a post-Hornby Bay Group, pre-Dismal Lakes Group topographic high. Uranium principally occurs as stratabound, often peneconcordant bands; a lesser amount of uranium is fracture controlled.Stratabound uranium exists in gently easterly dipping, subparallel bands ranging in thickness from 1.5 m to 6.0 m. Pitchblende, coffinite and sooty black uranium oxides occur as interstitial disseminations and grain coatings subparallel to bedding; they also replace pyrite and form narrow veinlets.Small amounts of torbernite, carnotite and cuprosklodowskite coat pitchblende and are disseminated within mineralized bands. Pyrite, marcasite, chalcopyrite, chalcocite, cove/lite, digenite, azurite, malachite, arsenopyrite, glaucodot, niccolite, bravoite (? ), goethite, hematite and magnetite as well as quartz, barite, calcite, biotite, chlorite and clay minerals exist within the mineralized bands. Uranium grades of 0.1 % to 0.3 % U3O8 over thicknesses of 1 m to 2 m are typical.A steeply dipping fracture zone near the Imperial fault contains sooty black uranium oxides, torbernite, carnotite and cuprosklowdowskite as well as sulphides, cobalt arsenides, quartz and carbonate. The zone may reach 70 m long; its true width is about 1.9 m. Uranium grades range up to 5.18% up, over0.9m.Pitchblende and coffinite from PEC deposit have been dated at 1.08 ± .10 Ga with possible remobilization at .45 Ga. The deposit contains an inferred 3,150 tonnes of U3O8."

Jan 1, 1986

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By C. R. Ince

THE term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalcopyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggart1 has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls .dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This-is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 lb. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 lb. per ton were added to the thickened pulp and the whole

Jan 1, 1929

By V. C. Allison

The explosibility of a dust is favored by its fineness and content of volatile combustible matter; its explosibility is decreased by its moisture and ash content. The explosibility of a dust can be reduced by admixture of either inert dust or water. The major effect of both the inert dust and water lies in their heat capacity; they absorb the heat of the explosion flame until the temperature of this flame drops below the ignition temperature of the explosive heat. The amount of inert dust necessary to make an explosive dust non-explosive can be calculated from its proximate analysis. FOREWORD LARGE-SCALE testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparation of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments con¬ducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have been reviewed by the Bureau of Mines., The Bureau has conducted many tests with the Frazer-Clement2 apparatus, which gives the pressures set up when the dust cloud within is, ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. An attempt has been made to design an apparatus that may be used for checking and correlating the experimental tests. The first design was a wooden gallery, 8 by

Jan 7, 1925

By C. Van Dyke, K. Van Dyke, J. Gutierrez, C. Nowack

"Using propidium assay and flow cytometry, we examined how silica exerts its toxicity toward phagocytic cells employing the human neutrophil as a model. This toxicity appears to be associated with calcium bound to silica. Once the silica with calcium is phagocytized, the extra calcium causes the death of the cell. Using ""Ca we found that 6 to 10% of millimolar calcium is bound to milligram amounts of respirable-sized silica (diameter of 5 µ.m or less) at physiological pH. If the silica particles arc coated with an organosilanc (Prosil 28). calcium binding is decreased by 60% as is cell death. Pretreating with INDO IAM (a chelator of intracellular calcium) reduces the cellular death by 80%. Nonfibrogcnic particles- polystyrene beads or coal dust-produced 10% or less cell death in a 4-h period. Silica with no added, external calcium appears to exert toxicity to neutrophils; however, pretreating cells with EDT A decreases cellular death to the level of nonfibrogcnic particles. Chronic toxicity with silica-calcium appears similar to the chronic toxicity in gout where particles cause a cycle of inflammation. c 1993 Academic Press, Inc.Silicosis is an occupational disease caused by the inhalation of fine particles of silica, usually between 0.1 and 5 µ.m in diameter (1). A recent hypothesis explaining silica's toxicity suggested that surface free radicals caused damage to cells (2). This explanation appears doubtful, however, since the addition of silica to water, such as that found in biological systems, quenches free radicals; also, such a hypothesis does not provide basis for a persistent inflammatory pattern that lasts for years. Kane et al. (3) proposed that silica's toxicity resulted from an excessive concentration of calcium ions within the phagocytic cell (macrophages). However, the mechanism that was capable of linking silica to an excess of intracellular, ionic calcium was not explained. The surface of silica is certainly involved because covering the surface with polymers or phospholipids decreases silica's toxicity (4-6).When silica is engulfed by macrophages platelet activating factor and leukotrienes are produced (7, 8). This is the same inflammatory pattern produced by phagocytic cells exposed to the calcium ionophore A23187 and ionic calcium. How could silica be acting like A23187? Perhaps calcium binds to silica extracellulary and then is released intracellulary following phagocytosis; the latter process, in a sense a ""piggy back"" process, would permit activation of inflammation and cell death mechanisms."

Nov 1, 1995

By R. M. Bird

Few persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry-sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co. A few years ago the so-called Albany sands were dug by simple methods and hauled by horsecart to railroad. Depletion of sand near railroad sidings and extended use of automotive power have appreciably extended the area from which sand is now being dug. It is not unusual to haul 5 miles to the railroad. As stripping is quite shallow, 6 to 18 in., and the banks of usable sand generally run from 12 in. to 4 ft., it is economical to work the bank by benches so narrow that the overburden can be thrown by hand shovel to the exposed bottoms. In effect the top soil goes back to where it was, but on a lower level. Consequently the general surface appearance of a mined acreage is the same as before. This condition is in fact cutomarily required when a farm owner sells his sand in the ground. After such replacement, in the course of 3 to 5 years the soil is no less fertile than it was before mining. The sand itself varies as to grain and bond vertically and also along the breast. No mechanical equipment has been developed to compete with hand shovels and no machine has as yet been devised that grades the sand as required. Uniformity of sand, as shipped, depends first, last and all the time on the man on the job. Mixing equipment can change the appearance of the sand and mask its lack of uniformity, but it will never correct wrongly graded sand, dug from the bank. Modern methods of testing are helpful in setting up standards against which the man in the bank can compare his sands, but a good bank foreman is the only assurance that the sand, as dug, matches the required sample.

Jan 1, 1926

US 4,135,913-Extraction of nickel values from iron-containing nickel sulfide ore, particularly pentlandite or nickeliferous pyrrhotite A mixture of raw ore, roasted ore, or iron powder, and coal as a reductant is heated to a temperature of 800- 1000° C in a nonoxidizing atmosphere to convert the bulk of the iron content to metallic iron while diffusing into the iron the bulk of the nickel, the mixture cooled, and the cool material separated into a magnetic fraction containing most of the nickel and a non-magnetic gangue fraction A Illis arid L S Renzoni, assigned to International Nickel Co, Inc Jan 23, 1979 7 pp (75-21) Filed 10-10-75 (621,343) Priority Canada, 10-27-72 (155,032) Same Canadian 981,910, dated Jan 20, 1976 Same British 1,389,145, dated Apr 3, 1975 US 4,135,917-In the recovery of gallium from a solution obtained by the digestion of bauxite or nepheline in an alkali solution for the production of alumina, the digestion solution is neutralized, the neutralized solution evaporated to an op¬timum caustic alkali concentration and adjusted to a ratio of alkali metal oxide to alumina of above 2, the corrected solu¬tion contacted with a gallium-aluminum alloy, arid high-purity gallium recovered from the solution by electrolysis or cemen¬tation K A Badaliants, et al Jan 23, 1979 6 pp (75-109) Filed 12-19-77 (862,201) Priority USSR, 12-22-76 (2,428,¬006) US 4,135,918-Extraction of copper from copper sulfide ore containing also one or more of the metals iron, nickel, arid cobalt Ore is roasted at a temperature of 750-800° C to expel sulfur, the sulfur-free calcine slurried in water containing a sufficient amount of sulfuric acid to supplement any sulfuric acid formed in situ, the slurry heated at 150-165° C in the presence of a reducing gas to form soluble sulfates of metals other than copper while reducing copper to elemental form, arid the slurry filtered to recover copper solids Any precious metals present in the ore will report with the copper solids V A Ettel, A P Devuyst, R Sridhar, arid C. E O'Neill, as¬signed to International Nickel Co, Inc Jan 23, 1979 5 pp (75-117) Filed 3-2-78 (882,610) Priority Canada, 5-13-77 (278,360)

Jan 1, 1980

TWO recent developments in open hearth steelmaking have had a substantial impact on metallurgical practices and operating procedures. These are: (1) the use of oxygen roof lances for accelerating the refining reactions, and (2) the use of a spring-arch, basic roof for prolonging the life of the furnace. Although these practices can be used separately, they are generally used to complement each other in an effort to obtain minimum heat time consistent with an acceptable rate of wear of the refractory roof, walls and port ends. DECARBONIZATION BY OXYGEN INJECTION The use of oxygen to speed carbon elimination was perceived by Sir Henry Bessmer but its practical use in steelmaking could not be realized until processes were developed for the manufacture of low cost, tonnage oxygen. However, as early as 1922 Bigge1 obtained a patent covering the use of gaseous oxygen to speed decarbonization of a molten steel bath. At that time, oxygen was available only in bottles and at a cost of $240 per net ton. At the end of World War II the price of oxygen had dropped to $80 per net ton, and as a result, metallurgical oxygen (99.5 per cent began to come into widespread experimental use for decarbonization in open hearth and electric furnace shops.2-8 Even this price prevented oxygen's routine use for other than decarbonizing the bath in shops producing substantial quantities of steels containing less than 0.40 per cent carbon. Today, tonnage metallurgical oxygen can be manufactured for less than $15 per net ton, and commercial purity oxygen (95 per cent is reported to cost less than $5 per ton. Thus, it is not at all surprising to find many open hearth shops effectively using large quantities of oxygen to accelerate decarbonization. Equipment for Oxygen Injection. The oxygen may be injected by a lance pipe inserted through the wicket hole and pushed several inches into the steel bath, or by a water-cooled jet inserted through the back- wall, endwall, or roof, and immersed in the slag or set just a few inches above the slag. Oxygen at approximately 100 psi is piped directly to control stations adjacent to each furnace. The installations should include adequate safety devices such as fire checks and emergency valves,

Jan 1, 1964

By Edward A. Capillon

The problem of scrap is probably of greater importance in the pro duction of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of thc base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is not generally feasible to assay every shop remelt it follows that the possibilities of lost values arc large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys. Metals Used in Alloying Pure gold, that is, gold of 24-kt. value is very much too soft for jewelry purposes and it is therefore always alloyed with other metals to increase its hardness and resistance to wear. For the same reason pure silver is seldom used alone but is alloyed with copper, the standard alloy being sterling silver which contains 92.5 per cent. silver and 7.5 per cent. copper. The metals commonly used for alloying gold are silver, coppcr, nickel and zinc. In addition to hardening the gold and producing alloys of different karat values the use of these metals makes possible the production of gold alloys of various colors such as yellow, red, green and white. The gold-silver-copper alloys vary in color from light greenish-white through green, yellow and red depending on the relative amounts of the three metals. Green or yellowish-green colored golds

Jan 1, 1930

By C. R. Ince

The term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalco-pyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggartl has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 Ib. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 Ib. per ton were added to the thickened pulp and the whole

Jan 1, 1930

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By A. J. Pearce

MOST mines have a model of some kind to illustrate either geological structure, mining operation, or some special condition or feature of the property. The type used depends on the particular feature or use for which it is intended. At Dome Mines we have developed an interesting and practical application of the horizontal-type model. This model shows the workings of each level horizon plotted on glass. These glass panes are set in frames which, in turn, rest on drawers equipped with rollers which can be pulled out as desired into a light chamber. The features of this model are its rigid steel construction and that any desired number of level plans can be pulled out, eliminating any other interference from other levels. Figures 1 and 2 are photographs of the model cabinet and show its construction and general features. The cabinet is of steel construction with the following overall dimensions: width, 6 ft. 5 in.; depth, 6 ft. 7 in.; height, 5 ft. 2 in. When not in use it can be completely closed-in, making the cabinet practically dustproof. There are 30 drawers, one for each of the 29 levels and one for the surface. The glass in each drawer is divided into two panes, 36 in. by 36 in., of flatdrawn double-diamond 'lustraglass' with about l/32 in. between adjacent edges. The panes are held rigidly in the frames, which are lined with felt strips, and may be adjusted by set screws, four of which on each drawer are shown in Figures 1 and 2. The level workings, on a scale of 1 inch equals 100 feet, are traced in ivory black Windsor & Newtons artist oil paint. Co-ordinate lines are shown in crimson lake, and main geological contacts are shown in their respective colours. Figure 3 is a photograph looking down on one of the levels. The lighting consists of 14 30-watt fluorescent bulbs, with reflectors, under frosted glass. These lamps are much more satisfactory when operated by 60-cycle rather than 25-cycle and, as we had available nearby a source of direct current, this was used. The electrical unit consists of a rotary converter from d.c. to 60-cycle. This arrangement gives perfect lighting, allowing most colours to be easily distinguished. Figure 1 was photographed using this source of light, Figure 2 using an outside floodlight.

Jan 1, 1945

By Richard E. Gray, Robert W. Bruhn

INTRODUCTION Underground coal mining has been practiced in the United States for over 200 years. Much early mining was not as efficient as today and unrecovered coal pillars, often of variable size and spacing, remain to support the overlying strata after mining has ceased. These conditions constitute a potential subsidence problem since the pillars will eventually fail. The possibility of subsidence above an abandoned mine must be anticipated except when total extraction has been achieved, permitting subsidence concurrent with mining, or when large coal pillars which have an adequate factor of safety for long-term support remain in the mine. Coal is found in 37 states and is mined under- ground in 22 states (HRB Singer, Inc. 1980). Underground mining produced 40 percent of the 7.5 x 10" kg. (830,000,000 tons) of U. S. coal mined in 1980 (Keystone, 1981). There are approximately 70,000 abandoned or inactive underground coal mines in the United States and approximately 2000 active underground coal mines (NAS/NAE, 1975). Underground coal mining in the United States will eventually extend beneath 162 x 109m2 (40 million acres). Thirty-two billion m2 (8 million acres) are already undermined (HRB Singer, 1977). Subsidence due to mining has affected more than 8 x 109m2 (2 million acres) in 30 states, 7.7 x 10 9m2 (1.9 million acres) from bituminous coal mining and the remainder primarily from anthracite mining (Johnson and Hiller, 1979). Subsidence from all other underground mines has affected only 6.9 x 10 7m2 (17,000 acres) (Johnson and Miller, 1979). Subsidence appears to be particularly widespread in two states, Pennsylvania and Illinois, although serious subsidence is found in localized areas of numerous other states (HRB- Singer, Inc. 1977). Host underground coal mining has occurred in the eastern United States, where the U. S. Bureau of Mines estimates 1.6 x 109m2 (398,600 acres) in urban areas in 18 states (out of a total 1.7 x 109m2 1418,400 acres]) are threatened by subsidence (Table 1) (Johnson and Miller, 1979). Pennsylvania and West Virginia contain 57 percent of the total threatened areas. The U.S. Bureau of Mines estimates the total cost to stabilize the estimated 1.7 x lo9m2 (418,400 acres) of subsidence prone urban land located above abandoned mines is over $12.5 billion (1978 costs).

Jan 1, 1982

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By J. P. Nowlan

"This paper is an attempt to outline the structural problems at the Cochenour Willans mine, in so far as their details have been tentatively worked out. It must be emphasized that there are considerable data that can be interpreted in more than one way, and that further work may modify or completely change some of the hypotheses presented herein. Certain features, however, are sufficiently constant to warrant reliance on them when searching for extensions of orebodies.As the individual ore shoots usually have relatively small dimensions, but are often very high grade, structural details are of more than usual significance in laying out a mining programme. An illustration of this is a small shoot recently located and mined as a result of studying a minor slip cutting off a part of high grade gold ore in No. 319 stope. The shoot, which is bounded on three sides by slips, and on the fourth by the original stoping, was roughly triangular in plan, 20 feet on the base, and 40 feet in length. The average width mined was 4.5 feet, but the gold obtained totalled over 1,800 oz.The property lies in Dome township, east of McKenzie island, and consists of an original group of thirteen claims acquired from the Cochenour Willans syndicate, plus one additional group of five claims obtained by purchase from the Kelson Red Lake Gold Mines, Limited, and one other claim that rounds out the southeast corner of the block.The claims of the original group were staked by W. M. Cochenour, Dan Willans, and Horace Young, during 1926 and 1927. The Cochenour Willans Syndicate was formed in 1928, and until incorporation of the present Company work was carried on at varying intervals by several different interests, including Ventures Limited, Hollinger Consolidated, who sank a shaft to open up the 150-foot level, and by the Syndicate itself. The first ore from the property was shipped to the Gold Eagle mill by the present Company in 1939, and amounted to 4,959 tons, from which 2,360 oz. gold was recovered. The first brick was poured in December, 1939, and production has been continuous since that date. To the end of June, 1946, gold having a value of $5,982,000 has been produced from 345,033 tons of ore treated."

Jan 1, 1954

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947