Search Documents

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By Helmut Mischo

For more than 100 years, diamond mining has been Namibia?s most important mining sector. Today, it provides the highest foreign currency income for the country?s development. Since the late 1970s, offshore mining of diamonds has gained more importance and now more than 60 percent of Namibia?s generally high-quality stones come from those offshore deposits, with a steady increase expected for the coming years. Diamonds in Namibia The mining industry is one of the three pillars of the Namibian economic development, along with tourism and fishing. Diamond mining is one of the two main mining activities in Namibia and diamond mining operations are rapidly moving from onshore to offshore deposits. This article provides a comprehensive overview of the current and future situation of the Namibian mining industry, with a special focus on the tasks and new technical developments for the successful excavation of beach and marine diamond deposits. The different deposits and the adequate applied mining technologies and methods are shown in examples.

Jan 1, 2011

By Bengt H. Fellenius

.1.1 Prior to commencement of pile installation operation, submit to [Engineer] for [approval] [review], details of equipment for installation of piles. SPEC NOTE: The information requested in 3.1 .1.2 is necessary as input to a detailed wave equation analysis of the pile driving. .1.2 For impact hammers, give manufacturer's name, type, maximum rated energy and rated energy per blow at normal working rate during easy and at termination driving, mass of striking parts of hammer, mass of driving cap, and type and elastic properties of hammer cushion. .1.3 For non-impact methods of installation, such as drilling, jacking, jetting, use of vibratory hammers, or other means, give full details of characteristics necessary to evaluate performance. .2 Impact Hammer SPEC NOTE: Do not exclude a hammer type unless for very specific reason. .2.1 [Drop hammers will not be permitted.] [Diesel hammers will not be permitted.] For final driving of [TYPE] piles, provide a hammer capable of delivering to the pile a non-erratic impact stress not smaller than [VALUE] Pascal and transferring a non-erratic energy not smaller than [VALUE] Joules per blow to the pile head at normal working rate.

Jan 1, 1991

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R Shrimali, P Rajmeny, L Shekhawat, A Joshi

Rampura Agucha open pit mine has successfully been excavated to a depth of 320 m, incorporating multistage working. The key to success is the implementation of presplitting as control blast measures at every stage of mining, including intermediate cut backs, in addition to the final wall. The major challenges encountered in establishing presplitting in the hang wall as compared to the footwall of the mine are:reversely dipping foliation, ie dipping into the hang wall itselfstriking obliquely at an angle of 20–30° with regards to the general strike of the pit wallthe presence of numerous geological planes of weaknesses like major faults, slips, etc.Control blast parameters like hole inclination, spacing and stand-off with buffer row were chosen initially from the literature survey and were subsequently fine-tuned by field trials to the mine geo-mining conditions of the hang wall. Electronic initiation used for trim blasts along with double presplitting in fault-affected zones helped in getting better presplit performance and resultant stability of the hang wall.CITATION:Rajmeny, P, Shrimali, R, Shekhawat, L and Joshi, A, 2015. Establishing the design parameters of a control blast for long-term stability of the hang wall at Rampura Agucha Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By Leandro Augusto Viana Teixeira, Márcio Francisco Dill Junges, Adauto Caldara

Innovation in the mining industry is critical when facing ever growing challenges, like the need to increase safety, reduce social and environmental impact, deal with commodities price fluctuations among others. However, successful innovation is not only the product of technological innovation, but it is also dependent on Innovation Management, which consists of changing the way a company fosters innovation, creating a new structure able to leverage technology knowledge and the ability to convert this knowledge in value. This paper presents a restructure option for innovation that focus on R&D development linked to business needs and company strategy. This new system was approached based on four fundamental blocks for innovation management (Approach, Organization, Resources and Metrics), showing how the technology master plan and a management tool are able to bring together all aspects necessary for the proper operation of the system. The new system confirmed the importance of having the initiatives organized as innovation roadmaps, connecting techno-scientific development with the company needs through the use of KPIs that are relevant to the business.

Oct 3, 2019

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By O. Lashkari, A. Charette, R. Ghomashchi

Conventional casting at low pouring temperature was employed to produce semisolid metal, SSM, billets of A356 Alloy. The deformation behavior of the as-cast SSM billets was studied using parallel plate compression viscometry. The compression tests were carried out at different applied pressures, and fractions solid. The rheological studies were conducted assuming the SSM slurry behaving like Newtonian and non Newtonian fluids respectively. The calculated viscosity numbers confirmed pseudoplastic behavior of the SSM billets and were correlated to fraction solid and shear rate proposing the following empirical equation which is valid at low shear rates, less than 0.01 s-1, and fraction solid of0.33-0.46: 0 log77 =5.56-l.38fs -(l.56fs +0.14)logy Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by G. Dufour, F. Paray and J. Tessier 0.33<fs<0.46

Jan 1, 2006

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Richard D. Hagni

The mineralogy of dusts from the lead sinter and lead blast furnace at the Doe Run Smelter at Herculaneum, Missouri is being studied by reflected light microscopy and scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS). Oust from the sinter plant consi5ts of abundant slag and galena particles, and lesser amounts of coke, sinter, and chalcopyrite particles. In contrast, dust from the blast furnace consist of abundant coke and sinter particles, and lesser amounts of slag, galena, chalcopyrite, metallic lead and lead-copper particles. The particles in dusts from remote sampling sites !-l mile from the sinter plant and blast furnace are fine-grained and composed principally of calcium-aluminum silicates that are locally derived, but some of the larger particles consist of sinter, slag, galena, and other minerals. Additional dust samples from the plant and remote sites are currently being studied.

Jan 1, 1991

By George G. Reed

Approximately 200 samples of iron ores and other iron- bearing materials have been tested for amenability to treatment by the R-N process in bench scale laboratory work. Twelve large lots, ranging in size from 900 net tons to 18,500 net tons, but generally 3,000 to 4,000 tons each, have been processed in the R-N demonstration plant. The ores tested in the demonstration plant ranged from 27 to 70 percent iron content and gave excellent results. (1) The demonstration plant has a nominal daily capacity of 50 tons of high quality iron briquettes and has now operated for over five years. A continuing program of process improvement is carried on between demonstration on potential licenses ores. An important development is the complete elimination of any secondary products which, in the past (2,3,4,5), resulted from treatment of certain low-grade ores.

Jan 1, 1960

By M. M. Coleman

An investigation of the behaviour of sphalerite, chalcopyrite, galena and pyrite during flotation was conducted on selected circuits in the Brunswick Mining and Smelting Corporation Ltd. concentrator in Bathurst, NB. Samples were collected from 59 locations and analyzed for Zn, Pb, Cu, Ag, Fe, As, Sb, Sn, Bi and S. Metal balances were computed using the CAMP Material Balance Program (MATBAL 5) and the metal recoveries for each cell and circuit were calculated. An automated image analyzer interfaced with an electron microprobe was programmed to measure the size of sphalerite, chalcopyrite, galena and pyrite grains in each sample. The percentage of each mineral occurring as free grains and the relative amount of each mineral present in binary and ternary particles was calculated. The recoveries and losses of Pb, Zn and Cu are compared with the amount of liberated and unliberated galena, sphalerite and chalcopyrite present in the concentrates and tailings.

Jan 1, 1989

By Pier Paolo Manca

The investigated area lies close to a large town and covers an area of about lkm2. The mine was worked at depths ranging from 5 to 100 meters but mining operations actually ceased some 50 years ago. There are seven coal seams, each one to two meters thick, overlain by sedimentary rocks in a strongly faulted area. Different kinds of subsidence have occurred, crown holes, shallow depressions and hummocky ground. The results of rock mechanical characterisation (RMR method) in the area have been used to define three different types of numerical model (FLAC 2D). A large numbers of simulations has been performed to solve three different problems at three different scales: to determine the, mechanical properties of the roof rock and overburden involved in the subsidence process, to assess the crown hole subsidence potential and to define the properties of the beam foundations.

Jan 1, 1999

By Yves Picot

Construction of new installations was recently completed in the Port of Tubarao, Brazil, With this expansion the port, operated by Companhia Vale do Rio Doce (CVRD), has become the largest iron ore port in the world, with an annual throughput capacity of 60 million long tons. GROWTH OR IRON ORE EXPORTS Since its formation CVRD has steadily increased the shipment of iron ore to overseas markets. Starting with less than 100,000 tons in 1942, the yearly export volume grew to 1,500,000 tons in 1951, 5,000,000 tons in 1961 and 25,000,000 tons in 1971. The number of different grades of ore also increased during this period. Production of high grade pellets, starting in 1970, further increased the number of ore products to be shipped. In the same period the size of ore carriers increased twenty-fold to over 250,000 DWT.

Jan 1, 1974

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003