Search Documents

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Soseol Kim

A high-performance Emulsion-based booster explosives has been developed that can be used as a booster for bulk explosives. Currently, Pentolite booster, which is mainly used as a booster for bulk explosives, has a high risk of accidents due to the sensitivity of its raw materials PETN and TNT, and has a low melting point, making it impossible to use it in high-temperature ground. The Emulsion-based booster was developed to maximize the Velocity of Detonation (VOD) while elimination the shortcomings of the Pentolite booster. The VOD of the Emulsion-based booster is about 6,500m/s, so it can maximize the performance of the bulk explosive. In addition, it can be used in high-temperature ground and does not cause accidental detonation due to the external environment. In this article, the performance of the Emulsion booster was verifies through comparative test blasting of the developed Emulsion-based booster and Pentolite booster.

Feb 6, 2023

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014

By Filiz Sahin

This paper presents a synthesis of TiB2 via carbothermal reduction method using a mixture of TiO2, B4C and C prepared in molar ratio of 2:1:3. Reduction experiments were carried out in a high temperature graphite furnace in a graphite crucible under argon atmosphere at different time (0, 15, 30 and 60 min.) and temperatures (1400, 1500 and 1600 °C). The products obtained were investigated using XRD technique.

Jan 1, 2008

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

By B. McFadzean, S. Pikinini, C. T. O’ Connor

Sperrylite (PtAs₂) comprises about 21% of the platinum group minerals (PGMs) in the Platreef ore and regularly reports to the tailings due to its poor floatability. Hence, improving its recovery will be of great economic value to the South African PGM industry. The reasons for its poor floatability are not yet clear. This paper seeks to understand the interactions occurring between PtAs₂ and common thiol collectors, viz. potassium normal butyl xanthate (PNBX), sodium normal dibutyl dithiophosphate (SNBDTP) and sodium normal mono butyl dithiocarbamate (SNBDTC). By understanding its interactions with these collectors, it is hypothesised that it will be possible to suggest ligands that may help improve the floatability of sperrylite. Mineral-collector interactions were studied by determining the molar energy of interaction using isothermal titration calorimetry and electrochemical techniques. The hydrophobicity of the mineral before and after adsorption of the collectors was determined by heat of immersion and its flotation response determined by microflotation tests. Microflotation tests using synthetic sperrylite at pH 9 showed low collectorless recovery of 34.8% and after adding the equivalent of one pseudo-monolayer of the PNBX collector, the recovery of 32.5% was obtained. Moreover, the addition of up to three pseudo-monolayers coverage of PNBX did not result in any increase in flotation recovery. A small recovery improvement was noted when synthetic plant water with the ionic strength of 0.0484 mol/L was used, but this did not hold for all collectors, with SNBDTP exhibiting higher recoveries in distilled water. Keywords: Sperrylite; flotation; recovery; adsorption energy; collectors; 2SPW (synthetic plant water)

Jan 1, 2020

By Robert Gordon, Leduar Ramayo

This paper reviews the application of the magnetotellurics method for deep earth imaging, specifically its recent use to better understand original mineral emplacement processes. Resistivity information from newer innovative applications of the technology for nearer surface imaging also provides valuable insights into near surface structure, which in some cases has led directly to new discoveries.

May 10, 2023

By T. J. Otto, I. D. Ungerer, G. C. Lindeque, T. J. van Heerden

Anglo American Kumba Iron Ore (Kumba) continues to implement technologies focussed on improving safety and productivity; this forms part of the groups FutureSmart Mining initiative. The paper provides insights into the implementation of three technology solutions that improves the productivity of heavy mining equipment (HME). Enhancements to the short term mine planning (STMP) process, the effective use of a fleet management system (FMS) and the deployment of drones or Remotely Piloted Aircraft Systems (RPAS) are discussed. The implementation of these and other technologies contributed to a 13% and 22% increase in the overall equipment efficiency (OEE) of the primary HME at Kumba’s Sishen and Kolomela mines respectively. Four key success factors (KSF) are highlighted namely that Kumba’s technology implementation drive is a key enabler to the company’s strategy, has a strong focus on value-add, is underpinned by a holistic and integrated implementation approach and is people-centric.

Sep 1, 2021

By Elias Macedo de Oliveira

Este trabalho tem por objetivo realizar a avaliação das propriedades mecânicas da zona termicamente afetada (ZTA) de junta soldada de aço fundido de alta resistência, obtida pelo processo eletrodo revestido, analisando o efeito da variação do tempo de tratamento térmico pós-soldagem. Foram soldadas juntas multipasses para avaliação de propriedades mecânicas de um aço fundido de alta resistência mecânica, com preaquecimento de 200°C, corrente contínua, posição plana e aporte térmico médio de 1,5 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados da ZTA e metal base, tanto na condição de como soldado quanto após tratamentos térmicos pós-soldagem. Os tratamentos térmicos pós-soldagem foram realizados à 600°C, por 1, 2 e 3 horas, visando avaliar o efeito destes tratamentos nas propriedades da ZTA. Os resultados mostraram que as propriedades mecânicas não apresentaram diferenças significativas em relação ao metal base com os tratamentos térmicos realizados, propiciando resultados satisfatórios em relação aos requisitos da norma IACS W22 Grau R4.

Aug 7, 2018

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By J de Witte

When used in suitable ground conditions, rock bolts can have advantages over other permanent tunnel lining solutions. Permanent rock bolts offer flexibility in tunnelling profile and rapid rock bolt installation can enable time and cost savings. There are also disadvantages when considering the suitability of rock bolts for permanent support installations. These generally concern achieving the specified durability requirement over the specified design life. By investigating alternate approaches to rock bolt installation, quality assurance (QA), monitoring and design life it may be possible to alleviate some of these concerns.The design and construction benefits that can be realised through the use of rock bolts are primarily related to reducing project program time. This time reduction could be realised if rock bolts are considered as a permanent solution, with the installation being completed as a part of the primary excavation cycle. Any reduction of the program could allow direct and indirect cost savings and in the case of a major project, allow the revenue stream to be realised earlier.Currently ambiguity exists where the treatment of rock bolts as permanent support components is inconsistent with that of (often identical) ground anchors, as utilised in stabilising cut and cover structures. The ground support design process, implementation and testing are generally similar, though the acceptance of rock bolts as long-term support elements is treated differently to ground anchors in technical specifications.This paper discusses some of the benefits available through the use of rock bolts. It offers different solutions to the concerns surrounding durability, including alternate approaches to installation, Quality Assurance practices and monitoring solutions. The selection of an alternate design life is also investigated as another means of alleviating concerns around long-term durability. The paper will also provide an indication of savings that could be expected through the use of rock bolts as part of a long-term support system.

Mar 8, 2011

By Derek du Preez, Andrew Hall, Timothy M. Pelech

Net Present Value (NPV) derived from Discounted Cash Flow (DCF) analysis remains the dominant metric for evaluating mining projects despite its well-documented inability to capture managerial flexibility under uncertainty. DCF assumes that all risks are perfectly priced by financial markets. This is an unlikely assumption for volatile commodity prices, geological variability, or the array of mining technical and operational risks present on all mine sites. Real Options Analysis (ROA) was developed to remedy this limitation by explicitly valuing the ability of managers to defer, expand, scale, switch, or abandon investments as new information emerges, and to capture upside and mitigate downside risks. While ROA is philosophically correct and routinely shows an uplift in project value compared with DCF, its practical application at industrial scale is severely constrained, ROA faces the reality of a combinatorial explosion in complexity of decision trees, Monte Carlo simulations and other models required when multiple interdependent or sequential options exist across numerous mining zones and time periods. The AMC Hill of Value® (HoV) process adopts the same intellectual foundation as ROA, that flexibility has economic value, but operationalizes it through a far more robust and scalable architecture. It is built on parametric relationships, rapid scheduling, and multi-objective evolutionary optimisation. HoV can evaluate millions of compound, interdependent real options in a single optimisation run, delivering resilient, adaptive strategies that preserve managerial flexibility while simultaneously optimising NPV, mine life, risk exposure, and other corporate objectives. This paper demonstrates that HoV is the practical, industrial-scale embodiment of real options thinking in mining: it discovers, ranks, and translates the most valuable real options into strategic mine plans, overcoming the scalability barriers that have prevented widespread adoption of classical ROA.

Feb 22, 2026