Search Documents

Technologies are receiving a lot of 'press' - and rightly so; as they are seen as the means for achieving quantum leaps in productivity and cost reductions. A point of concern for Caterpillar is that we do not believe there is enough understanding of the infrastructure needed to support some of the future technologies, as well there is not enough utilisation of the current systems.

Jan 1, 1997

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognised and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economical restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist with respect to the application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2006

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By Raj P. Singh Gaur

Due to high concentration of NaOH in the digested slurry after scheelite digestion, it is diluted to about 4N before filtration to separate sodium tungstate solution from the sludge (residue). However, in practice there may be deviations in the normality of NaOH present in the slurry. There may also be variations in the temperature of the slurry and filtration time. Slight variations in these parameters could cause tungsten losses in the sludge via the back reaction: Ca(OH)2 + Na2WO4? CaWO4 + 2NaOH This paper pertains to the effect of normality, temperature and time on the tungsten losses in the sludge that is separated from ?diluted-scheelite-slurry-in-NaOH? via filtration. Results indicated that tungsten losses in the filtered residue (sludge) were quite significant when the slurry temperature was kept at 70°C or higher. The effect of high temperature was less significant at the slurry normality of 3.6 or higher. Combination of low slurry normality (<3.6) and high temperature (>60°C) resulted into large W-losses in the sludge.

Jan 1, 2006

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

Study on Iron Ore Sintering with High Proportion of Specularite Concentrates Specularite iron ores have poor hydrophilicity and ballability as well as bad high-temperature reactivity, which restricts the large-scale application in the sinter and pellet production. In order to make the best use of the specularite concentrates, a novel process of Composite Agglomeration Process (CAP) is applied in this research. By the CAP, the percentage of specularite concentrates in the sinter mixture is increased to no less than 40 per cent as well as the coke breeze dosage is reduced by 0.3 per cent~0.6 per cent. Moreover, all the sintering indexes are obviously improved compared with the traditional sintering process. Researches on the metallurgical performances shows the finished composite agglomerates are high-quality burdens for blast furnaces. This investigation can provide an effective route to utilize the inferior specularite concentrates in the sintering.

Sep 13, 2010

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United Status. These data are presented in tabular form under the following headings; General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles. The first commercial unit employing the new thermoadhesive method of dry separation of minerals was installed at the Detroit mine of International Salt Company in Detroit, Mich. (Fig. l). This unit was first put into operation in March 1957. The purpose of the Detroit installation was 1) to serve as a pilot plant for evaluating the process on a commercial scale and 2) to produce marketable quantities of rock salt of improved quality and ap- pearance. The design of this plant was based on the results and information obtained from a 1-tph pilot plant at Battelle Memorial Institute. DESCRIPTION OF PLANT Location: The separation plant was installed underground near the crushing and screening plant, for this was the most suitable location from the standpoint of material handling. Furthermore, ample space was availabe at this location. Because the process requires a relatively constant temperature, the uniform year-around temperature of the mine (57°F) gave an added advantage to an underground operation. Feeding: The rock salt is conveyed to a surge bin, from which it is fed to the heating unit by a conveyor. The feed-rate control consists simply of an adjustable gate at the bottom of the surge bin. The plant may be fed either No. 1 grade of rock salt (0.279 to 0.375 in.) or No. 2 grade (0.375 to 0.500 in.) with a maximum input capacity of 500 tons per 15-hour day. Heating Unit: The heating unit (Fig. 2) consists of a panel of infrared lamps suspended inside a low-speed revolving screen. The radiant-heat panel, which is curved for most effective utilization of the heat, holds 240 infrared lamps of standard industrial type, each rated at 500 watts. The position of the panel is adjustable so that it can be placed centrally over and to within 6 in. of the salt bed on the screen. The entire heat panel is suspended by rollers in ¦ R. J. Brison and O. F. Tangel: Development of a Thermo-adhesive Method for Dry Separation of Minerals.

Jan 1, 1961

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By A. Varadarajan, M. Hashemi, K. G. Sharma

Quartz mica schist collected from Nathpa-Jhakri Hydropower Project, Himachal Pradesh, North India is tested under triaxial loading using a servo-controlled loading system. Complete stress-strain-volume change behaviour including post peak softening behaviour of the samples, are presented. Strength and deformation parameters are given. Quarz mica schist, der von Nathpa Jhakri Hydropower Projekt, Himachal Pradesh gesammelt wird, wird Nördlich Indien unter triaxial geprüft, der von Gebrauch eines servo kontrollierten Ladesystems beladung. Vollständiges Spannung-Spannung-Band Änderung Verhalten Postens Spitze Erweichung Verhaltens der Proben, wird überreicht. Kraft und Verformung Parameter werden gegeben. Mica à quartz schist recueilli du Projet de Hydropower de Nathpa Jhakri, Himachal Pradesh, l&apos;Inde du nord est essayé sous l&apos;utilisation de chargement de triaxial un système chargeant servo réglé. La tension complète-la tension-comportement de changement de volume y compris la poste sommet amollir le comportement des échantillons, sont présenté. Les paramètres de force et déformation sont donnés.

Jan 1, 2003

By Martin Pratt

This paper is an overview of deep foundation engineering in Hong Kong past, present and future. The enormity of the subject compared with the space available makes brevity inevitable. Issues of construction and design are covered and some examples of recent challenging projects are given. The content is aimed at those with an interest in foundations generally, but with limited knowledge of the Hong Kong scene. Reference is made to informative publications for further reading on specific topics.

Jan 1, 2000

By M Amanzadeh, S M. Aminossadati, B M. Masum, M S. Kizil, C R. Leonardi

Gas sensing systems are becoming more important in many industries such as oil, gas and mining operations. Particularly in underground coalmines, accurate and reliable monitoring of toxic and combustible gases such as methane, nitrogen dioxide, carbon monoxide and hydrogen sulfide is essential. Available conventional electrochemical sensors for gas measurements in underground coalmines suffer from shortcomings such as cross-sensitivity response, limited lifetime, high calibration cost, maintenance cost and safety. Recent studies have found that fibre optic-based gas sensors have potential to eliminate these issues. These sensors can also be used for long distance and distributed sensing of various gases, both of which are important for underground gas monitoring. The aim of this paper is to review the present underground mining gas monitoring systems and review the new generation of fibre optic-based sensing systems for use in underground coalmines.CITATION:Masum, B M, Aminossadati, S M, Leonardi, C R, Kizil, M S and Amanzadeh, M, 2017. New generation of gas sensors for underground coal mining applications, in Proceedings Australian Mine Vent Conference 2017, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1991

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99&nbsp;per cent&nbsp;extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text. Monitoring of the goaf gases as an early indication of spontaneous combustion has been incorporated in the mining cycle by placement of tubes in the goaf as the face retreats and continuous analysis of the goaf gases made at the surface by the National Coal Board tube bundle monitoring system.

Jan 1, 1980