Search Documents

By I Wilkomirsky

The neutralization of S02 from copper smelter gases to produce calcium sulphate (anhydrite) is considered an attractive alternative to sulphuric acid production. To develop the required technology for the process, a three-stages fluidized bed reactor prototype was designed and operated using both high and low grade limestone and gases with 2, 8 and 12 vol -% S02. The results obtained shows that at 800°C and up to 8 vol-% S02 in the gases, the capture of S02 reaches near 99% with limestone conversion to anhydrite of 45 to 48%. A larger pilot plant is presently being built at the Codelco El Teniente-Caletones Smelter to demostrate the technology and to evaluate the economics of the process. Cu2007

Jan 1, 2007

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By Harovel G. Wheat

It has been shown that the incorporation of fly ash into concrete as a replacement for part of the cement can be beneficial. In some cases, the strength of the concrete can be increased and the permeability can be decreased. This latter property can lead to a reduction in the migration and/or penetration of aggressive species into reinforced concrete. Some of these species, such as chlorides from deicing salts or marine environments, can subsequently result in accelerated corrosion of the steel reinforcement, a loss of the protection provided by the passive film on steel, and a loss of structural integrity of the concrete. Care has to be taken so that the appropriate compositions of the components of the fly ash are utilized in order to ensure maximum benefit to the concrete structures. This will be discussed as it relates to fly ash generation and treatment.

Jan 1, 2002

By M. Vondersaar, B. Bulnes

Quemetco, Inc.,. as a subsidiary of RSR Corporation, operates one of RSR's three secondary lead smelters in the City of Industry, California, next to a residential area within Los Angeles County. The Reverberatory furnace serves as the main reactor for melting lead grid and paste recovered by the battery crushing system. Feed material is introduced via screw conveyor after drying in an upstream rotary kiln. Slag produced by the Reverb flows directly to an electric arc furnace. Products from this one-pass furnace system consist of soft lead bullion from the reverb, hard lead bullion from the arc furnace, and a non-hazardous slag from the arc furnace. Furnace bullion is processed into finished product in a six-kettle refinery. An overview ·of plant operations is presented. Where applicable, references will be made to changes that have taken place during the last decade.

Jan 1, 2000

By William Hodder, Ehsan Alavi, Muhib Hussain

Disc Cutter Wear is influenced by several geological and technical factors and excessive wear can have a major impact on the excavation efficiency of Tunnel Boring Machines (TBM). Disc cutter replacement events cause a disruption to the construction schedule and costs, and should be minimized throughout the project to the extent possible. A well-executed cutterhead inspection and maintenance plan can help mitigate abrupt cutterhead interventions and reduce its effect on project schedule and cost. This paper examines cutterhead inspection and disc cutter replacement events as well as subsequent wear data recorded in the first 7km of the 10.3 km long, 6.3 m diameter Coxwell Sanitary Bypass Tunnel (CBT) project in Toronto, Ontario. The CBT alignment is mainly through Georgian Bay Formation shale.

Dec 1, 2022

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By Zheng-qi Guo, De-qing Zhu, Feng Zhang, Jian Pan

Iron mainly exists as the magnetite and fayalite, while copper is primarily dispersed in the form of fine matte particles in the copper slag, which is difficult to recover by conventional separation techniques. In this paper, the feasibility of an integrated technological route to improve beneficiation of copper and iron components from copper slag through the modification of molten slag was investigated, and the results shows that: the copper grade of rougher copper concentrate was increased from 6.43 to 11.04%, iron recovery from magnetic separation was increased significantly from 32.40 to 63.36%, and other evaluation indexes were changed slightly, in comparison with unmodified copper slag. Meanwhile, the grains of the target minerals in the modified slag grew considerably to a mean size >50 lm after slow cooling. Ultimately, the beneficiation efficiency of copper and iron was improved because of the ease with which the target minerals were liberated.

Mar 1, 2017

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Z. Smieszek, W. D?browicz, J. Pawlowski, G. Krawiec, J. Czernecki, J. Por?mbski, S. Gizicki

Rapid development of the automotive industry and motorization has been observed in Poland over the last decade. This phenomenon has increased the amount of used car batteries requiring recycling and has thus posed new challenges for their processing. Orzel Bialy" S.A, is the major secondary lead smelter in Poland. Ibis paper describes the program for smelting technology modernisation and productivity increase through the application of oxy-fuel burners, which has been implemented at "Orzel Bialy'' S.A. The main objective of smelter modernisation, which was to increase the furnace productivity by 20%, has been achieved. This paper outlines the previous and present state of the lead acid battery scrap smelting technology at the "Orzel Bialy" S.A. Specifications of the burners and of oxygen installation are given. Industrial tests with the modernised smelting technology and optimisation of the process parameters are described, and the results obtained are discussed.

Jan 1, 2000

By A. V. Neretin

This paper is a continuation and extention of the previous paper on energy-efficient placer mining methods which was presented in 2007 at the World Gold Conference in Cairns, Australia (Nere-tin, 2007a). The paper reports the results only on gravel processing as they were not fully discussed in the previous paper. It is common knowledge that placer gold mining requires processing of large tonnages of gold-bearing gravels by wash plants of different types. In Russia, gold-bearing gravels are mostly disintegrated and screened by the following types of wash plants: a water canon, a derocker or a scrubber trommel. Gold-bearing gravel processing is regarded as highly energy-intensive due to high energy consumption for transportation of large tonnage of material and high pressure water flow rate. The industries requiring a significant expenditure of energy normally estimate the process efficiency by energy consumption per product unit. In order to obtain quantitative data on energy consumption for gravel processing and to estimate placer mining costs, in 2003~2006 four placer gold mines located in the Irkutsk Region were thoroughly investigated through time and motion studies. At all these placer mines gravels were processed by a water canon, a derocker or a scrubber trommel. The objective of the study was to investigate the following parameters: ? wash plant throughput rate per hour; ? hourly diesel fuel and power consumption per cubic meter of gravel processed; ? volume per cent and shape of oversize material; ? different combinations of gravel processing methods. The results from this study were as follows: ? specific energy consumption per cubic metre of gravel processed for different combinations of gravel processing methods was estimated; ? a correlation between energy consumption and unit cost of gravel processing was determined; ? effect of yield and shape of oversize material on wash plant throughput rate per hour was de-fined; ? energy-efficient gravel processing methods were developed. Based on these results, an improved method of gold-bearing gravel processing was proposed. Implementation of this method at a placer mine saved US$ 123 000 in operating expenses only during a short-time Siberian placer mining season. At the same time, this method improved gravel disintegration, screening and processing operations used at the mine. Another advantage of the pro-posed method was higher gold recovery due to reduced yield of undersize material. In order to improve efficiency of gravel processing, a wash system including a derocker for primary gravel processing and a lightweight scrubber trommel was developed. There are two economic benefits of replacing water cannons with the proposed wash system. The first benefit includes lower operating costs for gravel processing due to lower specific energy consumption, while the second benefit is lower gold losses during slurrifying (disintegration and screening) and sluicing of the undersize material.

Jan 1, 2014

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

By Y. J. Ferdosi

This paper presents the outcomes of the preliminary investigation focused on the potential usage of Electrochemical Impedance Spectroscopy (EIS) in minerals processing. Currently, Electrochemical Impedance Spectroscopy has been successfully employed in the characterization of multilayer structures formed as molecules adsorb on flat surfaces and is commonly used in bio-related research. Few studies have explored the application of EIS in minerals processing, particularly for mineral particles and flotation systems. In the first series of tests, the impedance response was investigated as a function of particle size, shape and hydrophobicity using model quartz particles. The particle size fractions and the shape were found to contribute to the impedance response. The more hydrophobic quartz particles resulted in a higher impedance values. Further tests involved pure sulfide minerals including chalcocite, bornite, chalcopyrite and pyrite. The AC impedance measurements were conducted as a function of collector (sodium ethyl xanthate) dosage. The AC Impedance data was modeled using the combination of reference circuits. It has been shown that adsorption of collector onto sulfide minerals surfaces results in a higher magnitude of impedance. Increasing the collector dosage resulted in an increase in AC impedance for chalcopyrite, while a decrease was observed for chalcocite. Significant variations in impedance were exhibited by bornite and pyrite with a gradual increase in collector dosage.

Sep 1, 2012

By Matt Brandon

This case study demonstrates how integrating drone and GPS surveying with 3D modeling software creates more effective blast designs that address specific geotechnical challenges while improving safety and blast performance. In this case study an 80ft (25m) highwall experienced recurring slip plane failures exacerbated by a previously mined 40ft (12m) bench that removed back support, creating an unstable triangular rock mass. Previous blasting along this wall displaced the upper 40ft (12m) of material, opening geological discontinuities and causing progressive slope failures that compromised crew safety and blast effectiveness. High-resolution drone photogrammetry, GPS surveying, and laser measurements were employed to precisely map slip planes, bedding planes, and fault structures within the bench geometry. These geological features were imported into 3D design software to develop a shot pattern that strategically utilizes natural rock discontinuities rather than working against them. GPS-guided hole placement ensured accurate field implementation, while marking geological features on the surface of the bench provided visual references for the blast crew. The final blast design positioned the last row of holes to break preferentially along an existing slip plane while avoiding intersecting the next slip plane behind the blast. Explosive loading and timing sequences were adjusted based on the hole location relative to the 3D geological model to optimize fragmentation while maintaining wall stability. The optimized design improved highwall stability significantly, by reducing the slip plane failure mechanism that had previously compromised operations. Measurable improvements included enhanced highwall stability, reduced back-break, improved blast performance, and reduced safety risks for equipment operators and blast crews. Two subsequent shots using identical methodology were able to remove the rest of this problem area, confirming the repeatability and effectiveness of this integrated approach. This methodology demonstrates practical integration of surveying technologies with geological understanding to solve complex blasting challenges. Accurate 3D modeling of geological features enables blast designers to work with natural rock structures rather than against them, resulting in safer, more effective blasting practices. This case study shows the value of understanding the precise locations of geological features for optimizing blast design and provides a replicable process for addressing geotechnical challenges in blasting operations.

Jan 26, 2026

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By H. Link

"The extremely low permeability of the water-carrying beds in the nevonian formation of the potash district of Saskatchewan does not permit the injection of cement or chemicals to seal off sufficient water from the shafts to guarantee the safety of the mine. Based on many years of experience with wet shafts in the German and French potash mining industry, Alwinsal Potash of Canada Ltd. decided to have their potash mine shaft near Lanigan, Sask., which was completed in September of 1967, lined by means of an absolutely watertight lining of combined concrete and steel-plate construction.This shaft lining, consisting of two steel shells of welded construction with concrete filled in between, has proved itself before in the German coal mining industry. It guarantees a permanently dry shaft. With this type of lining, time-robbing and very often abortive injections are superfluous and the regular repair and adjusting work as well as the corrosion of conveyances and ropes can be avoided. Above all, however, the danger of a water inrush into the shaft is abolished completely."

Jan 1, 1971

By Rodrigo Afonso Hatwig

Os aços inoxidáveis duplex (DSS) e superduplex (SDSS) são ligas que se caracterizam por apresentar uma microestrutura composta por frações volumétricas similares das fases ferrita e austenita. Dependendo da composição química e do tratamento termomecânico aplicado, a microestrutura dos aços inoxidáveis DSS e SDSS poderá apresentar, além das fases ferrita e austenita, fases intermetálicas deletérias. Neste trabalho, um estudo termodinâmico-computacional foi realizado com o objetivo de acompanhar a evolução das fases de aços superduplex no intervalo de temperaturas entre 300°C e 1.200ºC. Para tanto, fez-se uso do software de simulação termodinâmica FactSage v. 6.4. Os resultados descrevem de forma eficaz as fases principais e secundárias em função da temperatura e composição química.

Aug 8, 2018

By John W. Walkiewicz

The U.S. Bureau of Mines has conducted studies to utilize rapid microwave heating to stress fracture ore samples. Iron ores containing hematite, magnetite, and goethite were subjected to microwave energy in batch operations at 3 kW and heated to average maximum temperatures between 840 and 940 °C. Standard Bond grindability tests showed that microwave heating reduced the work index of iron ores by 10 to 24 pct. In a microwave chamber designed to simulate a continuous throughput operation at 3 kW, the grindability of a taconite ore was improved by 13 pct at a bulk temperature of 197 °C. Because stress cracking occurred at a lower temperature, less energy was consumed. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous, belt-fed applicator. A significant improvement of grindability was obtained with a larger rod mill feed size in comparison to a minus 6-mesh Bond feed.

Jan 1, 2010