Search Documents

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By C. H. Page, Brenne

Theoretical modelling of a proposed sub-level open stoping mining system was carried out to assess pillar instability and potential for hanging wall caving. This modelling was done, at first, without detailed information concerning the rock mass structure and classification. After mining commenced, the deviance in behaviour from that predicted by the modelling indicated that the structure was having an appreciable modifying effect on behaviour. Further analysis was carried out with detailed engineering geological information and a recently developed pillar design method. The outlined procedure produced results for pillar size and strength that explained the behaviour that had been recorded.

Jan 1, 1983

By A. C. Veatch

Jan 1, 1921

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Jared Ball, Darren Snashall, Paul Telford, Pengfu Tan, Ben Hogg

"The foamed converter charges were up to 3 8 per month in Xstrata Copper Smelter at Mount Isa. The issue of high converter foamover frequency had remained unsolved for many decades in Mount Isa. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow, in order to understand the mechanism of converter foamover. The model predicts the chemistry and viscosity of slag during slag blow and copper blow. The effects of oxygen potential, charge of dirty reverts, slag carryover, under-blowing, over-blowing, and temperature on the foamover and viscosity of slag in copper blow have been discussed. A theory has been developed to understand the mechanism of converter foamover. The practical solutions have also been developed and implemented in Mount Isa Copper Smelter. Some improvements of the industrial operations have been presented. After a series of improvements, the number of foamed charges per month in the converter operations has been decreased significantly from 35 in Aug 2008 to only one per month in 2009/2010.1. IntroductionThe Copper Smelter in Mount Isa receives the concentrate containing about 25% copper and produces anode copper that contains about 99% copper. There are several stages in the process. The first stage carries out in the ISASMELT™ furnace. The ISASMELT™ process produces a molten copper matte containing about 60% copper. An iron-silica slag and a sulfur dioxidebearing off-gas are the by-products of the process. The slag is taken to the slag dams for cooling before it is recycled through the Mount Isa Copper Concentrator.The matte is sent to Peirce-Smith converters. The converters further remove iron and sulphur to produce blister copper which contains about 97% copper. The anode furnaces remove any remaining sulphur and oxygen to produce anode copper that is about 99. 7% pure. This is cast into anodes and sent to the Xstrata Copper Refinery in Townsville for final refining.In the copper pyrometallurgical industrials, slag foaming is an important phenomena which occurs when the gas bubbles have stability and not rupture. Foaming greatly increases the interfacial area between matte, slag and gas and is essential for the operation of high intensity smelting processes. However, foaming or foamover is undesirable in P-S converter since it can damage the equipment and injure the operators. Figure 1 shows that the whole process of a foamover development in a converter."

Jan 1, 2011

By C. W. EICHRODT

NUMEROUS requests for the suspension of publicity make difficult the preparation of the annual review of copper metallurgy for 1934. In the United States, sales allocations indirectly have set restrictions on the scope of activities of producers and refiners, and necessitated closer cooperation between secondary and primary producers. However, the feeling exists that preparations for a return of intense competition should not he neglected, and careful investigations are being conducted for ways and means of improving industrial positions and production methods. In all probability, efficiency in technique and equipment will prove of far greater importance in the near future than production capacity, and many important developments in copper metallurgy later will be found to have been born during the current year.

Jan 1, 1935

By L. E. Schultze

[The Bureau of Mines conducted bench-scale studies to develop techniques for stripping tetravalent cerium from tri-n-butyl phosphate solutions. Experiments were conducted in a constant-temperature bath using beakers and mechanical stirring. Ninety-five pct of the cerium was stripped from a 50-pct tri-n-butyl phosphate 50-pct kerosene solution containing 0.18 M cerium in 15 minutes at 50° C using 0.11 M aqueous formaldehyde.]

Jan 1, 1974

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By H. G. Stephenson

Canada and the United states are both developed countries with economies which are extremely dependant on oil. Canada exports 37% of its production (to the United states) and imports 35% of its consumption (mainly into Eastern Canada), making the country self-sufficient in oil. Canada is attempting to increase its oil production so as to simultaneously reduce its dependence on foreign oil while producing more oil for export. The United states -imports no less than 50% of its total consumption of 17 million barrels/day. Canada's exports to the United states form only 7% of the United States total imports. The United States would clearly prefer to achieve self-sufficiency in oil. Consequently both countries are dependent on foreign oil. The united States is however in the sensitive situation of depending, for its imports, on countries which are susceptible to destabilizing political events. It is the author's hypothesis that recent developments in underground oil recovery from the Athabasca oil Sands of Alberta may well, for both countries, form part of the solution to these problems.

Jan 1, 1991

By M. I. Dobrynina

At the beginning of the 80-s the first diamond pipe in the East-European platform was discovered in the North of the Russian Federation on the White Sea Winter coast. During several years while studying this unique area data on kimberlites and country rocks petrophysical characteristics have been collected. Considerable experience in geophysical methods when searching and exploring diamonds was accumulated, and various methods of geophysical data interpretation were used. It has been established from the analysis of geophysical data that diamond-bearing kimberlites are located in the most ancient and the most stable block of the East-European craton.

Jan 1, 1995

By C. M. F. Vieira

The main characteristics and physical and mechanical properties of clays from the county of Campos dos Goytacazes, located at the northern part of the State of Rio de Janeiro, Brazil, are presented. The characterization included mineralogical composition, chemical composition and particle size distribution. The properties related to water absorption, linear shrinkage and flexural rupture strength were obtained in samples that were prepared by 20 MPa uniaxial pressing and fired at 950 and 1100oC. The results showed that the clays are predominantly kaolinitic with high percentage of clay minerals. The kaolinitic structure associated with a small amount of fluxes confers a refractory behavior which makes difficult the sinterization and impairs the ceramic consolidation.

Jan 1, 2009

By Clifford R. Porter

A 200 pound per hour Magnex Pilot Plant was designed and constructed. A non-compliance Eastern Coal which would generate more than 2.0 lb of SOZ per million Btu upon burning was brought into compliance (less than 1.2 lb of S02 per million Btu) during continuous operation of the pilot plant. Approximately 85 percent of the pyritic sulfur was removed while recovering 86 percent of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex Program is reviewed.

Jan 1, 1977

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH' and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By John W. Lane, Richard A. Ronzio, Frederick N. Bender

Climax Molybdenum Co. operated a hydrometallurgical plant at Climax, Colo., from August 1966 to August 1968 to recover molybdenum from an oxidized ore. The feed, tailings from sulfide flotation, was first upgraded by cycloning. The concentration plant handled 6000 tpd of feed and produced 2000 tpd of slime concentrate. The concentrate was leached by a sulfuric-sulfurous acid solution at 65°C. The molybdenum was solubilized in the form of "molybdenum blue." Activated charcoal was added to the leach tailings in a resin-in-pulp type circuit. Molybdenum was adsorbed on the charcoal. The charcoal was screened from the pulp and washed. The washed charcoal was pumped to columns where it was ammoniated and air-blown. The oxidized molybdate then was washed from the charcoal. The eluate was evaporated until ammonium dimolybdate crystallized out. The ammonium dimolybdate was calcined to molybdenum trioxide.

Jan 1, 1973