Search Documents

By R B. Stewart

Where pasture production is the intended land use of the areas to be reclaimed, the creation of a suitable growing +medium is a major objective. To achieve this land reclaimers require a sound understanding of the proposed mining plan and a knowledge of the physical, biological and chemical properties of materials intended for resurfacing disturbed areas. Where the original soil is not being replaced in its natural state, research is usually required to determine an alternative growing medium. Results from field research conducted on waste material from the Waihi Gold mine are reported with emphasis on the significance of soil depth in relation to pasture production in this environment.  Problems in extrapolating field research to large scale operations are also considered.   Essentially the requirements for successful pasture production, on surrogate growing medium, are akin to conventional approaches used in New Zealand in the development of unimproved agricultural land. High inputs of fertiliser are initially needed, especially where volcanic soil is used, and careful management of pastures and soils is required to minimise soil erosion and create a sustainable system. In the first three to five years of pasture production, grazing use of the land requires to be dictated by pasture availability and soil conditions and not by animal feed requirements. The use of light stock (young dairy or sheep) is recommended.   Successful land restoration requires a team approach by a range of cooperative specialists including engineers, soil scientists, farm managers, agricultural contractors, landscape architects and environmental officers.

Jan 1, 1991

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By J. P. Mogan, E. D. Dainty, A. Lawson

"The toxicity reduction of emissions from two diesel engines by the emulsification of water into fuel oil was investigated to determine the applicability of such systems to underground mining machinery. . The engines studied were: 1) the Deut; F6L7J4, four-stroke, air-cooled, 6-cylinder, V-configuration, indirect-injection (IDl) engine, and 2) the Detroit Deisel Allison Division 8V7JN, two-stroke, water-cooled, 8-cylinder, V-configuration, direct-injection (Dl) engine.The application of emulsified fuel treatment to the two-stroke engine did not prove to be practicable. In the case of the Deutz engine, however, substantial benefit resulted. For a modest J5 per cent water content in the fuel and an injection timing of24° BTDC, approximate reductions of40 per cent in the concentrations of both particulate matter and nitric oxide (NO) were produced. These reductions were accompanied by insignificant changes in other toxic constituents. The net result was an approximate 30 per cent reduction in the over-all exhaust toxicity for typical LHD operation as assessed by the Health Effects Index criterion. This toxicity reduction represents a significant advance from the points of view of an improved underground environment and/or reduced ventilation costs."

Jan 1, 1981

By M Rattenbur, A B. Christie, S C. Cox

A new minerals initiative to increase the level of understanding of New Zealand's mineral resources and to promote the development of minerals began earlier in the year in a partnership pilot-project between Crown Minerals and the Institute for Geological and Nuclear Sciences (GNS). The project aims to gather a set of comprehensive geoscientific data and build a series of digital GIS packages to highlight New Zealand's mineral prospectivity. The pilot study was carried out at a regional scale, and is focussed on mesothermal gold mineralisation in the South Island. A significant amount of geological data and information was sourced from open file technical reports held by Crown Minerals and from various databases held by GNS and has now been compiled into a single GIS dataset, which will soon be made freely available to interested parties. In addition to this comprehensive data compilation, prospectivity modelling using Weights of Evidence techniques was undertaken to highlight those areas likely to contain ore deposits. It is clear from this study that the South Island of New Zealand remains highly prospective for mesothermal gold mineralisation. Many of the highly prospective areas, which also contain historic mine workings, remain open for exploration. The study not only highlights these areas, but also other areas where the potential for similar mineralisation exists, in all likelihood with no surface expression. The study has also highlighted the value of many of the open-file technical reports held by Crown Minerals and the need to carry out additional studies using this and other available data at a more detailed level, possibly as the basis for a web-based minerals information system.

Jan 1, 2002

By Jerry B. F. Champlin

The successful injection of liquids into subsurface permeable formations for production stimulation, storage, or waste disposal requires a rapid, precise, and accurate method of determining the permeability of porous solids. This report describes a method and apparatus, developed by the Bureau of Mines, that use the principle of specific-volume permeametry. Calibration of the apparatus over a wide range of permeabilities and standardization of several apparatus constants have eliminated many of the tedious calculations and problems of manipulation common to some other methods. Improvements in reproducibility and accuracy have resulted from reducing experimental measurements to one parameter--time. Specific permeabilities of reservoir rock samples are determined directly from a chart that relates elapsed time to a permeability equivalent to that determined by bubble-tube measurements.

Jan 1, 1962

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By Earl C. Hutchison, Wade C. Hutchison

T 0 effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre- and postblast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By A. U. Seybolt, R. E. Honnemon

THE purpose of this communication is to present activity data of nickel in the Ni-A1 binary system that was obtained for oxidation studies in this system. This data has been calculated from previous aluminum activity data at 1000°C1,2 by two types of Gibbs-Duhem integrations. These results should be of particular current interest to oxidation studies of aluminide coated nickel-base superalloys3 as well as other problems. The aluminum activity of Steiner and Komarek1 is plotted in Fig. 1 as a function of composition in Ni-A1 alloys at 1000°C. The dashed parts of the aluminum curves represent our approximate extrapolations from the directly measured regions. In the terminal solution regions (a and L phases) standard parabolic solution functions of the following form are assumed: where i is the component subscript, Ki is a constant at a fixed temperature, and xi is the atom fraction. The resultant nickel activity curve at 1000° C from the Gibbs-Duhem integration4 of the aluminum data is shown in Fig. 1. The solubility ranges of the phases present in the Ni-A1 binary at 1000°C are also denoted at the bottom of Fig. 1. Corresponding values of the nickel activity, aNi and yNi, are listed in Table I at useful compositional intervals. including phase boundary values. The aNi and yNi data listed in Table I are subject to the uncertainties present in the experimental aluminum activity data1 and to deviations from parabolic solution behavior in the terminal solutions. The errors introduced into aNi and yNi due to the parabolic solution assumption are expected to be relatively small (<20 pct of the values given) in all the phases except the liquid phase. Some deviation from parabolic solution behavior in the liquid phase is indicated

Jan 1, 1970

By Phil Jones, Ben Johnson

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations:

Jan 1, 2019

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation&apos;s Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system&apos;s 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By D. W. Wu, M. T. Haque

A novel impedance probe has been commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mud-line, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mud-line information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are re-viewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2000

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r&apos; panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By John W. Sweeney

The southeastern phosphate industry is investigated to determine its role in supplying the United States and world phosphate demand. The report shows that the southeastern (Florida, Tennessee, and North Carolina) phosphate industry is the leading domestic and world producer of phosphate rock, The report emphasizes size and organization, production capacity, transportation, and marketing of the southeastern phosphate product, Factors affecting the supply- demand relationship of the southeastern phosphate industry and world phosphate production-consumption relationships are analyzed and related to the southeastern phosphate industry. Past trends are projected and the future role of the southeastern phosphate industry is analyzed to determine its ability to supply the United States and rest-of-the-world phosphate requirements in 1985 and 2000. The projections show that southeastern resources are ample to supply domestic and export requirements at the projected rates of consumption well beyond the year 2000.

Jan 1, 1970

By M. C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions, the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs. Comprehensive reports have been issued.

May 1, 2005

By G. Righettini, G. Desrivières, P. Mousset-Jones, R. Lacroix, M. C. Bétournay, P. Laliberté, S. Hardcastle

"Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another.This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America.Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs.Comprehensive reports have been issued."

Jan 1, 2005