Search Documents

By Y. Akin

The floatability of a typical boron mineral, colemanite (Ca2B6O11.5H2O), is shown to be hindered by the presence of montmorillonite type clay minerals. The clay is found to act in the form of slime coating. The mechanism of slime coating is investigated using pure colemanite and clay and their mixtures with an anionic reagent in a microflotation cell. Adsorption, flotation, solubility, zeta potential and scanning electron microscope studies reveal that slime coating occurs through electrostatic attraction. It is possible to minimize the effect of slime coating either at high surfactant concentration or at high pH values.

Jan 1, 1997

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By William E. Ford, Edward Salisbury Dana

A. Anhydrous Carbonates The Anhydrous Carbonates include two distinct isomorphous groups, the CALCITE GROUP and the ARAGONITE GROUP. The metallic elements

Jan 1, 1922

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By R. Wachtell

IN order to study better the phenomena at work in various phases of diffusion of the Fe/Si system when compounded and alloyed by powder metallurgy methods, several attacks have been planned. Electrical, hardness and other measurements have been discussed e1sewhere.l,2 The metallographic phenomena will be considered here. Concerning the metallography of the ferrosilicon alloys, some initial discussion is in order. As this laboratory discovered to its chagrin, there are many traps that lie in wait for even the experienced metal-lographer when he deals with alloys of high silicon content. Chief of these is probably the anomalous behavior of these materials under conventional etching techniques. We have before us, for instance, Corson's paper" of 1928, wherein is mentioned and illustrated (probably for the first time) the peculiar "barley shell" structure sometimes found in these alloys. Again in 19412 he same author reports the structure in 5-14 pct silicon irons. Houghton and Becker mention its presence' but make only tentative effort to explain it. In 1943, Hurst and Riley6 discussed the "barley shell" and declared it to be a false structure, resulting from the peculiar and characteristic film-forming propensities of the alloy. At about the same time, Wrazej7 proved correct the contentions of Hurst and Riley, establishing pretty well the mechanisms of formation and identifying the constituents involved. Hurst and Riley6 a1so describe in their paper (1943) a "cracked film" structure, also a pseudo-morph, the precise nature of which they do not suggest. Careful examination of such a film reveals that it not only cracks but begins to curl away from the surface of the metal and peel, much in the manner of flaking paint. The careful microscopist will be able to focus on the topmost edge of the flake, and, by optical sectioning, follow it down to the metal surface. We have been able, by oblique illumination of such specimens, to observe the raised segment of the film, the shadow that it casts, and the mating segment on the metal into which it fits. As late as 1946, Hurst and Riley8 found occasion to correct misinterpretation of this "cracked film" structure in a work by others on a 12 pct Si/Fe alloy. The "barley shell" and "cracked film" pseudo-morphs are not the only ones encountered in studies of these materials. A third pseudomorph, which may, however, have some structural significance is a fine striation of the surface. Closely spaced and parallel striae extend entirely across single grains. Each grain shows a different direction for the striae, and different closeness of the spacing. The regularity of this structure, and the fact that the striae do not cross from one grain to another, suggest that the structure is a film cracking controlled in some way by the crystal plane orientation of the surface being etched. In general it is wise for the metallographer dealing with these alloys to cultivate a feeling of uncertainty not only of the more complex questions of interpretation, but also of the basic question of whether that which he sees is indeed a true representation of the structure. We have taken, as a first test of the validity of a structure, its reproducibility "in situ" after repolishing and re-etching of the samples. Thus we knew the "barley shell" to be false (fig. 1) even before encountering the definitive works on the subject. The Metallography of Silicon Diffusion in Laminate Bars: As a first step in the study of the metallography of the diffusion process, we have pressed a series of laminate bars. These bars, or "sandwiches" as we have termed them, were pressed with covering layers of iron powder, and a "filler" of the Fe/Si master alloy under study. Bar dimensions were approximately %, x 3 x 1/4 in. The total

Jan 1, 1951

By Keith Jones, Martin Knights, Timothy Watson

In 1996 a KBR (Brown and Root) led international JV was appointed to design and supervise an underground and surface package. The design of 6 km of tunnels, plus enlargements, deep shafts in glacial and sandstone deposits for the conversion of the existing LEP underground laboratory at CERN, Geneva adjacent to the Jura Mountains/Lake Geneva had to be undertaken in an operational environment and in conjunction with other underground constructions associated with the US$3bn refurbishment.

Jan 1, 2003

By Dwayne D. Tannant

The Adra tunnel near Naramata BC experienced a fire in 2010 that burned timber sets within the tunnel and caused severe spalling of rock from the roof and tunnel walls. The nature of the damage is documented and efforts completed to rehabilitate and open a portion of this tunnel to the public are described. The use of shortcrete and rock bolts is a technically and economically superior support system to timber sets as well as being far more fire resistant.

Jun 1, 2012

By A. M. Galperin

Back analysis is a very important procedure for proper understanding of physical processes. Back analysis can be used to establish the role of different factors, define parameters to be calculated and formulate the behavior of natural or physical processes based on field experimental results. It is evident that, in order to obtain the necessary data for back analysis, field observations are required. For the Michailovsky region (Kursk Magnetic Anomaly, KMA) the long-term strength characteristics of the clay covering the quarry slopes were established with the help of back landslide calculations. The obtained data allowed quantification of the shearing resistance parameters at the presence or absence of intermittent dips of discharge in the pit bank massif structures. Based on the results of investigation for material composition, strength and deformation of finely dispersed (clay-chalk) deposits in the Kursk Magnetic Anomaly including measuring of the settlements of filled structures, complex probing and laboratory determination of water-physical and mechanical properties of "man-made" soils, engineering-geological zoning of filled structures was carried out.

Jan 1, 2005

By Tweedy. D. H.

"The paper describes the rapid development of, and operational experience in the utilization of, pneumatic low-pressure pipeline hoisting systems to vertically convey raw coal and rock through shafts, supplementing shaft capacity-the greatest lift to date being 535 m.A typical installation has raised over 250,000 tonnes in less than one year from a depth of 413 m through a 350/ 400-mm pipeline at a rate of 85 tonnes per hour. Operational experience on seven systems has provided valuable data on performance and operating costs.The main advantages of the systems lie in the flexibility of the pipeline to occupy existing free space in shafts and underground roadways, the relatively low first cost, the short delivery and installation time, and the economical running cost.Conclusions are therefore reached on future applications for example, the use of boreholes in older mines where new production technology has outstripped shaft or slope capacity, inter-level hoisting to implement concentration on transport roads and perhaps full mine output from relatively small mines.IntroductionIt is seven years since the basic art and practice of the pneumatic hoisting of minerals was described. The technique was developed in Western Canada by Radmark Engineering and found favour in the United Kingdom with the National Coal Board. Engineering and commercial feasibility trails were conducted in collaboration with the Mining Department and Mining Research and Development Establishment of the N.C.B. There was also considerable involvement with the British Health and Safety Executive.During the last five years, rapid progress has been made in the installation of new systems in the United Kingdom, Hungary and other countries. The operational experience gained makes it possible to report ""in depth"" on these installations, which cover a wide range of different physical mining applications."

Jan 1, 1982

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By F. L. Bosqui

A. L. BlomFIeld, Denver, Col. (communication to the Secretary.*) — Mr. Caldecott says on p. 67: "The Dorr thickener shown, while a useful device when crushing with cyanide solution for removing surplus solution from slime pulp prior to air-lift agitation or vacuum filtration, is not adapted to effect as complete a separation of water from settled slime as the ordinary intermittent settlement and decantation." This statement might have passed muster in this country several years ago when. the Dorr thickener was a new device, but its use in hundreds of mills in the United States has demonstrated that as thick a product is being discharged from it as was obtained from the intermittent settling which it has supplanted. • It is interesting to note that recent investigation, especially the work of 11. 6. Coe and G. H. Cleveilger,' in the March Bulletin of the Institute, under the title: Laboratory Method for Determining the Capacities of Slime Settling Tanks, has developed the general theory of settlement and explains the results obtained in practice. Just as free settlement is a function of surface area, so thickening after the zone of free settlement is passed is a function of time. The time required is obtained by the capacity or volume provided in the settler for this thickening zone. Each pulp is a problem in itself, both in regard to free settlement and to time required to reach a commercially finished thickness. Some pulps require 48 hr. and more to reach a density of 40 per cent. solids; others no coarser to the screen test reach a density of 65 per cent.' solids in a fraction of that time. In thickening any pulp a point is reached where the increase in density is so slow as to be commercially unprofitable. When any part of the pulp has reached this point it should pass on for treatment—its place in the thickener should be occupied by pulp which has not yet reached the commercial limit. By doing this the whole volume of the settling tank is kept in active use. Thus the continuous thickener keeps the whole tank at work to its commercial limit, while the intermittent settler has much of its volume occupied at times by pulp which is either quite finished thickening or at least thickened past the commercial point. The mechanical efficiency of the continuous thickener can be the only argument for limiting this statement. In my own experience I have never

Jan 1, 1916

By Larry Kaufman, Morris Cohen

THE solid phase equilibria' and the martensitic transformation in the iron-nickel system have been the subject of considerable study. In addition, there have been numerous investigations on the calorimetric and thermodynamic properties of iron-nickel alloys. The purpose of the present work is to extend the existing information concerning the martensitic reaction in the iron-nickel system, and to develop a general thermodynamic treatment which will encompass the equilibrium and non-equilibrium phase

Jan 1, 1957

Studying the ore textures in a discrete orebody is a novel approach to estimating liberation potential of the ore minerals present. As part of a PhD thesis, this project aims at classifying and quantifying the textures of the Hilton North orebodies, and at estimating their liberation characteristics.

Jan 1, 1993

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior's Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Mar. 10, 1917, to Apr. 10, 1917. ADKINS, HARVEY S Adkins & Denham, Engineers, Box 291,. Hazard, Ky. ANDERSON, ARTHUR P .... Leaser, Gibson Copper Co., Box 1978, Miami, Ariz. ARNOLD, EDWARD C... Min. Engr., Chief Engr., Federal Lead Co., Flat River, Mo. ASKIN, THOMAS B. H., Ball Mill Expert, Inspiration Cons. Copper Co., Miami, Ariz. BAIN, C. KREMER Butte & Superior Mining Co., Butte, Mont. BAKER, WILLIAM A.,.JR., Vice Pres. & Sales Mgr., The Georges Creek-Parker Coal Co., 306 North Gay St., Baltimore, Md. BOOTH, GEORGE H Mech. Engr., Inspiration Cons. Copper Co., Miami, Ariz. BRIDGMAN, G. TEMPLE, Asst. Consulting Mining Engr., Guggenheim Bros., 120 Broadway, New York, N. Y. BROOKS, CHARLES A Mine Surveyor, Homestake Min. Co., Lead, So. Dak. BUTCHER, FREDERIC E., Secretary, Missouri Metals Corpn., 1945 Railway Exchange Bldg., St. Louis, Mo.

Jan 5, 1917

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By D. G. Osborne

"The paper describes current 'tools' available to the coal preparation engineer for carrying out the evaluation of data, process design, selection of equipment and layout and design of coal preparation plants.Laboratory and pilot-scale equipment is widely available and test data can be used to provide valuable design information regarding capacities and sizing for specific applications. Pilot plants, unless they fit closely to the basic design envisaged for the eventual commercial plant, C(In often provide only limited useful information.Computing aids such as equipment simulation, plant modelling, etc. are becoming widely applied for establishing design criteria and investigating flowsheet options . Other computer tools such as computer-aided design systems are taking over some of the time-consuming tasks of detailed layout and design and estimation of quantities, etc. and providing the means for detailed examination of more than a single option.Besides computer modelling there is also physical modelling of plant buildings, plant sites and entire proposed mining areas; the former can be especially useful in finalizing design and threading' pipework and electrical reticulation systems through the plant without the resultant risk of impairment of flow, obstruction or wastefulness. Not the least of the benefits of plant models is the assistance provided for training new operating and maintenance staff."

Jan 1, 1985