Search Documents

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By Gabriel Esterhuizen, Tom Goodwin, Scott Schilling, Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in plane-polarized reflected light, colour changes are observed which are characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film!coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins. Bituminous coal gave the best results.

Jan 1, 1970

By Rudy J. Matetic

Over-exposure to noise remains a widespread and serious health hazard in the U.S. mining industries despite 25 years of regulation. Every day, 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) noise level exceeds 85 dBA and more than 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the permissible exposure limit (PEL). Additionally, MSHA coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage comprise only seven different types of machines; auger miners, bulldozers, continuous miners, front end loaders, roof bolters, shuttle cars (electric), and trucks. In addition, the MSHA data indicate that the roof bolter is third among all the equipment and second among equipment in underground coal whose operators exceed 100% dosage. A research program was implemented to: 1) determine, characterize and to measure sound power levels radiated by a roof bolting machine during differing drilling configurations (thrust, rotational speed, penetration rate, etc.) and utilizing differing types of drilling methods in high compressive strength rock media (>20,000 psi). The research approach characterized the sound power level results from laboratory testing and provided the mining industry with empirical data relative to utilizing differing noise control technologies (drilling configurations and types of drilling methods) in reducing sound power level emissions on a roof bolting machine; 2) distinguish and correlate the empirical data into one, statistically valid, equation, in which, provided the mining industry with a tool to predict overall sound power levels of a roof bolting machine given any type of drilling configuration and drilling method utilized in industry; 3) provided the mining industry with several approaches to predict or determine sound pressure levels in an underground coal mine utilizing laboratory test results from a roof bolting machine and 4) described a method for determining an operators’ noise dosage of a roof bolting machine utilizing predicted or determined sound pressure levels.

Jan 1, 2006

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By S. Burks

This paper develops the themes explored by the authors at the Fourth International Platinum Conference,. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: > An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated > An existing operation with an integrated portfolio of mines, concentrators, smelter, and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets > An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated > An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the owner's team.

Jan 1, 2013

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Edwards A. B

A table concentrate obtained experimentally by the New Occidental Gold Mines N.L. has unusual interest on account of the presence in it of abundant coated or "black" gold. The concentrate was obtained from ore from the New Cobar mine, Cobar, New South Wales, by feeding the oversize product from a "Dorr Bowl classifier to a Card table.Its assay value was 129 oz. of gold and 52 oz. of silver per ton, yet practically no free gold could be seen on panning.When, however, the concentrate was digested in hydrochloric acid fine rusty gold could be obtained by panning.The following chemical analysis was carried out by the mining company on a similar sample of concentrate.

Jan 1, 1941

By K. C. Armstrong, A. B. Cron, L. A. Melis

"The Johnny Mountain gold mine in northern British Columbia, owned by skyline Gold Corporation, has been in operation since August 1988. Mill operating difficulties at the start of the operation resulted in a depleted cash flow situation and quick improvements were required to generate a self-sustaining financial basis of operation. In October 1988, Melis Engineering Ltd. was contracted to identify metallurgical difficulties, implement necessary modifications, and undertake mill operations and personnel training in order to achieve production targets.This paper presents the operating difficulties which existed at start-up and describes the methodology used to overcome production problems. Metallurgical testing results are described along with the modifications made to the milling circuit to suit ore metallurgy. Plant changes led to the operation of a simple gravity/flotation circuit to recover gold as bullion and in a copper concentrate. Operation of the originally installed cyanidation circuit was discontinued. This contributed to substantial savings in operating costs and virtually eliminated environmental problems. PROPERRTY LOCATION ANR DESCRIPTIONThe Johnny Mountain mine site is located in northern British Columbia along the Iskuit River about 60 km east of Wrangell, Alaska and 275 km north of Terrace, B. C.. A location map is presented in Figure 1 and a site plan is shown in Figure 2. The complex is located on a mountain plateau about 3, 600 feet above sea level. The plateau is flanked to the north by Johnny Mountain and surrounded on the other sides by steep cliffs."

Jan 1, 1990

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992