Search Documents

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world&apos;s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of 160-250 Mt; however, all previous attempts to extract the PGE from this ore type have proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas the arsenide- and sulphide-PGMs that make up approximately 25 per cent of the original Pt content of the ore largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd) -oxides or hydroxides, or in iron-hydroxides, Mn-Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2013

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Raquel Dei Agnoli

Membranas a base de polímeros perfluorosulfonados, como o Nafion® (DuPont), vêm sendo extensivamente usadas como membrana de troca protônica em células a combustível. Contudo, o elevado custo e a baixa condutividade em temperaturas superiores a 80oC restringem o uso destes dispositivos. Em opção ao uso da membrana Nafion®, membranas a base da blenda polindeno sulfonado/polifluoreto de vinilideno (SPInd/PVDF) foram desenvolvidas, investigando o efeito da composição na performance das membranas. As membranas foram produzidas por evaporação de solvente da solução dos polímeros precursores. As blendas foram caracterizadas por termogravimetria e calorimetria exploratória diferencial. A caracterização das membranas eletrólito envolveu medidas de grau de inchamento, capacidade de troca iônica e condutividade protônica. Foi possível observar que o PVDF confere boa resistência mecânica e aumento da estabilidade térmica das membranas. Membrana com 50% em peso de PVDF apresentou a maior condutividade protônica (1,89.10-3S.cm-1). Membranas de SPInd reforçadas com PVDF mostraram resultados promissores para uso como eletrólito em células a combustível.

Aug 17, 2017

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By Marcelo Rebellato, Leonardo Silvestre, Zhang Yongqing, Felipe Bastos, Zhang Weiqiang

This work reviews the new version of GB1499.2-2018 Chinese national standard and specification, which governs the production of high-strength reinforcing hot rolled ribbed bars in China. In addition, it discusses the main concerns from Chinese rebar makers that might affect production and application of Nb-bearing rebars, like reheating temperature required to dissolve given niobium additions, the promotion of bainite microstructure and continuous yielding, as well as Nb strengthening effects. Through extensive investigation involving both thermomechanical laboratory simulations and industrial trial, the existing state and effects of Niobium along the reheating, rolling and cooling are illustrated. At the end, optimum processing conditions have been established to produce high strength rebars for the specified requirements. The adoption of new process conditions reflected in an amount of about 20.0 million tons of Nb-bearing rebar being produced in China in 2018 with required tensile properties and microstructure, and helped rebar makers to reduce production costs considerably. Based on production data, Niobium demonstrated positive strengthening effect for high strength rebars, in particular for small diameter rebars with earthquake resistant performance. What is more, the results of the research enrich the knowledge of the application of Niobium in steels when TMCP rolling is not used.

Oct 1, 2019

By José Aparecido Pereira

Este trabalho descreve uma nova metodologia para análise de calibração de cantoneira bem como realizar alterações de calibrações existentes, usando para isto a fórmula de Ekelund. O ponto chave da metodologia é a transformação dos passes de cantoneira em passes planos e a determinação dos coeficientes de alargamento de cada passe. O levantamento dos fatores foi baseado em projetos existentes e em amostras coletadas em laminadores.

Aug 17, 2017

By Rafael César de Souza

A distribuição de gás de Aciaria, gerado no processo de produção de aço, tem como finalidade que a energia térmica recuperada seja utilizada nos seguintes processos da TKCSA: - Aquecimento dos regeneradores dos Altos Fornos e Planta de PCI através do fornecimento de um Mix Gas composto de gás de Alto Forno, gás de Aciaria e gás natural; - Fornecimento de gás combustível associado ao gás de Alto Forno para as turbinas a gás da Termoelétrica, para que a energia térmica seja convertida em energia mecânica e finalmente em energia elétrica; - Fornecimento de gás combustível para o forno de ignição da Sinterização e os fornos de aquecimento de panelas da Aciaria. - Fornecimento de gás combustível associado ao gás natural para uma caldeira que tem como finalidade a produção de vapor de processo. Sendo um processo extremamente importante dentro do sistema de distribuição de Utilidades e termos como diretriz a redução de custos operacionais e obtenção de benefícios ambientais, foram desenvolvidas várias ações para aumentar a capacidade de distribuição do gás de Aciaria, sendo que tais ações proporcionaram um incremento de 20% na capacidade de distribuição do gás de Aciaria.

Aug 17, 2017

By Karen Leão dos Santos

A borracha sintética (SBR) é amplamente utilizada em indústrias de pneus combinada a cargas de reforço para melhoria das propriedades do elastômero puro. Atualmente, as cargas que apresentam melhor capacidade de reforço em elastômeros são a sílica e o negro de fumo. O presente estudo buscou avaliar o desempenho de compostos de borracha sobre as características de resistência ao rolamento, tração em piso molhado e resistência à abrasão, em função das quantidades de sílica e de negro de fumo. Foram realizados ensaios mecânicos e dinâmico-mecânicos, e, a partir dos resultados obtidos, concluiu-se que a utilização das diferentes cargas de reforço no composto de borracha está associada ao tipo de uso a que se destina o pneu.

Aug 17, 2017

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By Saulo Brinco Diniz

O presente trabalho buscou explorar a influência de um tratamento térmico de ressolubilização, realizados com distintos tempos (70, 80 e 90 minutos) a uma temperatura de 510ºC, na microestrutura e na dureza de uma liga de alumínio 7475- T7351. Para verificar a influência destes tratamentos térmicos foram utilizados um durômetro (fabricante EMCOTEST, modelo Duravision 300) e um microscópio óptico (Olympus, modelo GX51). Após os resultados obtidos, pode-se evidenciar que a liga de alumínio em estudo sofre um envelhecimento natural (a temperatura ambiente), e dentre os tempos de encharque estudados, 70 minutos é o tempo que possivelmente obtém-se a maior ressolubilização dos precipitados.

Aug 17, 2017

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By Noel G. Thomas

"This paper will identify where the industry is heading with iron· ore in the next ten years. From a customer&apos;s point of view, an indication of the changing, yet expanding, market will be made. This will progress further into the most likely changes in chemical and physical requirements of the ore products. No definite target can be set for 1990, but the logic from the direction of the changes will be established.IntroductionThe tonnage and quality of iron ore produced in the eighties will be heavily influenced by energy and investment considerations. That&apos;s not a great pronouncement, but this paper will explain how these two factors are :(I) influencing a disproportionate growth of electric furnace capacity and a greater use of scrap for iron units, in place of Iron ore;(2) influencing chemistry specifications; and(3) causing extensive examination of ore agglomerate form. Inflating investment costs are emphasizing the need for more productive blast furnaces, and the iron ore burden is under heavy examination as to how it affects productivity and coke rate."

Jan 1, 1981

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By T. E. Gray

This report describes the preparation characteristics of the more significant coal beds in Allegheny County, Pa. It is one of a series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. More than 7 million tons of coal was produced in Allegheny County in 1957. Of this, more than 5 million tons was cleaned mechanically in nine cleaning plants. The Bureau of Mines estimated that, as of January 1, 1953, more than 384 million tons of recoverable coal remained in the county in beds 28 inches or thicker.

Jan 1, 1959

By Joseph C. Milbourne

Tetra Technologies CCIX? (continuous countercurrent ion exchange) system has been involved in a wide range of uranium concentration, separation and purification applications over the past 40 years. Uranium ion exchange applications have ranged from the treatment of copper heap leach solution containing 5 parts per million of uranium to the treatment of high strength sulfuric acid solutions containing several thousand parts per million of uranium. The flexibility and the countercurrent mode of operation and other unique features of the CCIX? have resulted in successful uranium recovery from these solutions and many others.

Jan 1, 1995

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

By Charles P. Lazzara

Concentration profiles of low-pressure, slightly lean CH4-02-Ar flames have been measured in situ for the following unstable species: oxygen atom, hydrogen atom, hydroxyl radical, methyl radical, and formyl radical. The observed maximum mole fractions were 2.0X10-2 for H, 1.1X10-2 for OH, and 0.8X10-2 for 0; the maxima occurred in the recombination zone. Methyl and formyl radicals have maximum mole fractions in the reaction zone of 2.2x10-3 and 6x10-5, respectively.

Jan 1, 1973

By Ozdemir. O.

Magnesium additions to aluminum enhance strength and hardness, lowering density, and improving corrosion resistance. However, during melting and casting processes, significant amounts of magnesium are lost due to selective oxidation. Preventing these losses would reduce the production cost and improve the quality of the final product. The effects of strontium addition on the oxidation behaviour of aluminum-0.5% and 1% magnesium alloys were investigated by monitoring sample weight gains with time with a thermogravimetric balance at 750°C. Sample cross sections have been examined using Field Emission Gun Scanning Electron Microscope.

Jan 1, 2004

By Jadson Barbosa

Corpos de prova de ferro com diferentes níveis de pureza – um de pureza ultraelevada, dois de pureza elevada e um puro comercial – foram testados mecanicamente com diferentes taxas de deformação no âmbito de um antigo projeto. O objetivo era obter a resistência à tração de cada material e verificar a influência das impurezas e da taxa de deformação nas propriedades mecânicas do ferro de pureza ultraelevada. Para melhor compreender os resultados desses ensaios de tração, uma caracterização microscópica detalhada dessas amostras é realizada através deste trabalho. Para tal, foram analisadas as superfícies lateral e de fratura dos corpos de prova de tração no estereomicroscópio e no Microscópio Eletrônico de Varredura (MEV). O dano foi analisado em seções longitudinais ao longo do eixo de tração utilizando o microscópio óptico; a estrutura dos grãos deformados foi investigada por meio da técnica de microscopia EBSD (Difração de elétrons retroespalhados). Microestrutura, padrão de deformação, orientação dos grãos e as características das superfícies lateral e de fratura são então comparadas quanto ao processo de fabricação, nível de pureza e taxa de deformação.

Aug 17, 2017