Search Documents

By V. Jokovic

Hydrocyclones are the most commonly used classifiers in the mining industry. The reason for this is their low operating cost and a small footprint. Data from plant trials where screens replaced hydrocyclones indicated that lower bypass of fines and sharper separation could improve breakage rates, with a positive effect on flotation circuit performance throughput. Despite the importance of classification, hydrocyclones have not received as much attention as more expensive comminution units, and their technological progress has been incremental. Noticeable water split (Rf) reductions of a semi-inverted hydrocyclone have been reported in the past. According to theory, the hydrocyclone with reduced Rf will improve classification of fines. A classification study using semi-inverted hydrocyclones was conducted to determine if a hydrocyclone could be operated in a way that would minimise misclassified fines. The classification performance of a semi-inverted hydrocyclone will be presented in this paper and other potential applications will be discussed. Keywords: Semi-inverted hydrocyclone, water split, misclassification of fines

Jan 1, 2020

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Mineral Exploration Best Practice Guidelines (the Exploration Guidelines) have been prepared to assist professional geoscientists and engineers to conduct consistently high-quality work in order to maintain public confidence. The Exploration Guidelines are meant to assist professional geoscientists and exploration practitioners in planning, supervising, and executing exploration programs. In Canada, there are generally two types of public resource reporting: “Disclosure”, as defined by NI 43-101, is the reporting of technical information to the public and market participants for securities legislation purposes where a Qualified Person (QP) must be involved, and reporting of exploration information for governmental agencies to support obligations under laws including the Mining Acts of each of the Provinces and Territories. The Exploration Guidelines are also relevant where the results will not be publicly reported but are intended for internal company use. While this document is intended as guidance for work conducted or supervised by geoscientists in Canada, many of the practices described herein can be adapted to mineral exploration activities in other countries. The Exploration Guidelines are not intended to inhibit original thinking, or to prevent the application of new approaches that may develop into fundamental components of successful mineral exploration programs. Rather than provide prescriptive solutions to specific issues, they include general guidelines for current professional practice and to demonstrate and defend the merits of new methods. These guidelines do not preclude individuals and companies from developing more detailed guidelines specific to their own requirements. The initial version of the Exploration Guidelines was prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) Exploration Best Practices Committee and adopted by CIM Council on August 20, 2000. On January 9, 2018, CIM Council formed a new committee, the Mineral Resources and Reserves Committee (CIM MRMR Committee) with a mandate to, among other things, update the Exploration Best Practice Guidelines. The mandate for the committee was accepted by CIM Council on March 2, 2018. The new document was adopted by the CIM Council on November 23, 2018.

Nov 23, 2018

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By Janine Feitosa de Deus

Compósitos ambientalmente corretos, fabricados a partir de fibras naturais lignocelulósicas (FNL), estão entre os mais investigados e aplicados atualmente. Dentre as FNL, destacam-se as fibras de Rami (Boehmeria nivea), que surgem como alternativa em sistemas de blindagens multicamadas, para uso em coletes de proteção balística, por serem leves, de baixo custo, resistentes e ambientalmente corretos. No presente trabalho, investigou-se o comportamento mecânico de compósitos de matriz epóxi reforçados com tecido de rami, através de testes de flexão. Compósitos contendo separadamente 0, 10, 20 e 30% em volume de tecido de rami e resina epóxi, foram fabricados em um molde metálico, sob condições de vácuo. Os corpos de prova fraturados foram analisados em MEV e os resultados foram avaliados visando algumas propriedades de flexão com a incorporação do tecido de rami, visando sua posterior aplicação em blindagem balística.

Oct 30, 2017

By Feng-guang Li, Rui Guo, Ju Zhang

Cooling stave is one of the most important equipment of blast furnace for iron making. The heat transfer performance and service life of the cooling stave, to a large extent, determines the efficiency and economy of the iron making process. In this paper, a 3-D heat transfer model of cooling stave was founded by ANSYS based on FEM theory, and the heat transfer characteristics of cooling staves which were made of different materials (cast iron, cast steel and copper) were analyzed. Then, several suggestions on choosing material of cooling staves were given according to the calculation results and the actual working conditions of the cooling staves.

Mar 1, 2017

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By Y G. Anoman

This paper discusses the operating model within Endeavour Mining Corporation regarding the options of owner mining against contract mining. It’s based on the concept of ‘are we carrying out the most efficient mining’ regarding cost and performance. This question can only be answered through an extensive contract mining tender process and conducting a comprehensive comparison to evaluate the transition viability. Karma mine, located in Burkina Faso, is the subject of this paper. The Tender model included sales of equipment, parts and tooling associated with the traditional Load and Haul Schedule of Rates (SOR). The methodology focused on the structure of the tender process, which consists in the development of a SOR based on haulage profiles and mining schedule. This is a new Endeavour framework that allowed the bidders to compete on an even level. This was performed using a systemic analysis which encompassed all the elements involved in a transition such as the Human Resources (HR), taxes and customs implications, directs and non-direct costs (Finance and interest on assets, depreciation, insurance), contractor risk profiling. It was assessed against the normalised internal pricing tender-based. This paper gives an insight into how a West African mining operation addressed the sensitivities of the HR functions against the commercial aspects. This was one of the most successful transitions in West Africa and was carried out during the COVID crisis. The outcome of this project has created value by detailing a lesson learned model for both commercial and HR aspects. This discusses the commercial comparisons along with the internal model with the underlying HR functions as a risk factor that could have jeopardised the continuation of the operation. This resulted in a smooth transition with the additional cash flow generated by the sale of the parts and equipment turned Karma into a viable operation.

Jun 22, 2022

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By S. Abu-Samra

By virtue of its complex nature, the construction industry comprises a wide spectrum of interrelated variables and factors. This multifaceted character of the construction industry puts the use of engineering modeling tools and techniques on top of project management necessities. This research introduces a macro-level earthmoving management system using Genetic Algorithms (GAs) to reach the optimum allocation of earthmoving equipment. The Earthmoving Equipment Management System (EEMS) functions through four integrated modules: (1) A Central Database containing information about projects and available equipment; (2) An Equipment per Segment Selection module that calculates the cut and fill quantities, plots the Mass Haul Diagrams, and selects the equipment types to be used for each segment; (3) An Equipment Pool module which determines the production and cost for each available equipment, based upon the project site conditions; and (4) An Optimization Engine equipped with a GA optimization solver. This engine formulates the optimum earthmoving cost for all projects, by changing the number of allocated equipment. The Optimization Engine takes into account the number of available equipment and calculates the weekly equipment allocation. The EEMS model was implemented on an earthmoving company conducting five different projects on hand. The model proved to be an effective tool in providing decision makers with optimum equipment utilization on a multi-project scale to minimize the earthmoving cost. The results were then compared with the company?s existing micro-level management system, demonstrating better performance on the level of savings, amounting to 13% of total earthmoving cost.

Aug 1, 2013

By Johan Hillman, D. Scott Scovira, Thomas Gustavsson, Alexander Bihlar

Hydrogen Peroxide Emulsion (HPE) explosives are an alternative to conventional commercial explosives. HPE does not contain nitrates or ammonia thus eliminating post-detonation NOx fumes and aqueous nitrate discharge. Production of HPE is less carbon intensive than industry standard ammonium nitrate-based emulsions (ANE) and employment aligns with end users seeking to meet Scope 3 ESG emission targets. Swedish tunneling contractor Implenia Sverige was awarded the Högdalen Depot Expansion Project by the City of Stockholm. Implenia Sverige partnered with Hypex Bio to be the first to pilot the application of a nitrate-free explosive system in a large-scale civil construction tunnel. The purpose of the joint project was to evaluate the operational suitability of replacing conventional nitrate-based bulk explosives with HPE in a large-scale tunnelling project. When the project commenced in September 2023 both standard nitrate-based emulsions and HPE emulsion were used in parallel (Tunnel Right and Tunnel Left) to enable operational, performance, and environmental comparison. Identical drill patterns and initiation techniques were applied to both tunnel headings. Performance data collected included round advance, usage, and perimeter quality. Implenia managed all drilling and charging operations and Hypex Bio provided technical support, including technicians and chemists. HPE is viscous and pumpable using conventional emulsion pumping delivery systems. Variable density functionality enabled loading different charge weights into cut, lifter, production, and perimeter holes. The primary rock type was hard sedimentary gneiss with approximately 150 MPa [21,755 psi] Uniaxial Compressive Strength (UCS). Fracture systems with infilling occurred in both tunnel directions. Rock quality factor was “Good to Very Good” on the RMRb (Rock Mass Rating) scale. Epiroc Boomer rigs were used to drill rounds averaging 4.9 m [16 ft] deep with high accuracy and precise reference positioning.

Jan 26, 2026

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By F. D. Rodriguez, J. Ramirez Cuellar, J. Salinas Reyes, C. Gómez-de-la Garza

The Pickling Line and Tandem Continuous Mill (PLTCM) at Ternium Pesquería Facility with a Five Stands, Six High configuration started in 2013. Manufactured by PRIMETALS, to produce steel to exposed automotive market, Turnkey project, with supervision of best practices from Nippon Steel. The main equipment that the process has are; Laser welding machine, 3 loopers, Scale Breaker, jet Pickling tanks, Inspection Station and COGNEX System Side Trimmer (flying width change), Type of Mill: UCMW(S) Carrousel, 2 Tension Reels. The principals goals are, Simulate production programs, validate materials for thin thicknesses before processing, low Re-welds, optimization use Cognex, good performance in Thickness, flatness and productivity.

Oct 1, 2019

By Mostafa Sharifzadeh, Ebrahim Ghasemi, Kourosh Shahriar

"The Tabas Central Mine (TCM) is one of the underground coal mines located in the Tabas coal region, in the mid-eastern part of Iran. This mine is the first mechanized coal mine in Iran that uses the room and pillar method. Pillar design is one of the most important issues in underground coal mines, especially in room and pillar mining. In this paper, a new method for coal pillar design in the main panel of TCM is presented. This method is able to estimate the magnitude of the various loads (both development and abutment loads) that pillars might experience throughout the mining process. Also, the method reduces the pillar failure risk. Based on this method, proper pillar sizes in TCM are obtained (11.6 x 11.6 m (38.l x 38.1 ft)).INTRODUCTIONPillar design and stability are two of the most complicated and extensive mining problems related to rock mechanics and ground control subjects. Although these problems have been investigated for a long time, to date only a limited understanding of the subject has been gained. Prior to this, the dimensions of a pillar were largely determined by experience based on trial and error, intuition, or established rules of thumb; any research available tended to be isolated and sporadic. But nowadays, various pillar design formulas have been developed based upon laboratory testing, fullscale pillar testing, and back-analysis of failed and successful case histqries. In 1980, a number of ambitious field studies conducted by the U.S. Bureau of Mines developed the ""classic"" pillar design methodology. It consisted of three steps (Mark, 1999, 2006):1. Estimating the pillar load using tributary area theory2. Estimating the pillar strength using a pillar strength formula3. Calculating the pillar safety factorAlso, Bieniawski (1981) presented a step-by-step method to determine coal pillar dimensions in room and pillar mines. In this method, similar to the classic method, pillar load is estimated by using tributary area theory.Currently, in mqst of the room and pillar mines, remnant pillars in panels are recovered by retreat mining (pillar recovery). Hence, the above mentioned methods are not appropriate for pillar design, because in these methods pillar load is estimated by the tributary area theory, and the effects of abutment loads, which result from retreat mining and the creation of a mined out gob, are ignored. Abutment loads affect the pillars in the adjacent of pillar line and a load greater than what is estimated by tributary area theory is applied on the pillar. So, pillar design without considering the abutment loads leads to pillar failures during retreat mining. Pillar failures continue to be one of the greatest single hazards faced by underground coal miners. Pillar failures are responsible for unsatisfactory conditions, which include the following (Mark et al., 2003):"

Jan 1, 2010

By J Edman, RáBeamish, G Cambourn, B Beamish

Moist Adiabatic Benchmark (MAB) and R70 testing have been applied to core samples of a multiple seam sequence from a borehole at the Doyles Creek Project. The coal samples range in rank from high volatile B bituminous to high volatile A bituminous, with a general increase in coal rank as depth increases in the borehole. The intrinsic coal reactivity to oxygen decreases with coal rank as indicated by the R70 values. The time taken to reach thermal runaway shown by the MAB testing however is strongly modified by the interaction between the intrinsic coal reactivity, the moisture content of the coal and the retained gas content of the coal. This is clearly demonstrated by the lowermost seam of the sequence. The MAB test for coal from the Whynot Seam took 20 days to go to thermal runaway, which projects to heating issues taking between eight to 12 months to occur for loosely piled coal found in coal roof falls or a longwall goaf and uncompacted stockpiles, assuming sufficient air is available for coal oxidation. The results from this project illustrate leading practice for the operational planning and development of an appropriate spontaneous combustion management plan (SCMP).CITATION:Beamish, B, Cambourn, G, Lewis, G, Edman, J and Beamish, R, 2013. Application of leading practice spontaneous combustion assessment to exploration at the Doyles Creek Project, in Proceedings The Australian Mine Ventilation Conference , pp 293-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Dandan Jian, Christian Karcher

Information of liquid steel flow patterns inside the mold may be obtained from the velocity at the free surface (meniscus). This meniscus flow may be measured using the contactless electromagnetic technique termed Lorentz force velocimetry (LFV). It is based on the measurement of Lorentz forces acting on a magnet system when an electrically conducting metal melt interacts with the field lines stretched by the magnet system. Force sensor and the magnet system form a so-called Lorentz force flowmeter. In this paper we present a series of model experiments that demonstrate the feasibility of using two identical flowmeters that are arranged in a certain distance one behind the other. In this case, surface velocity may be determined by just cross-correlating the two force signals recorded by the two sensors. This technique is called time-of-flight LFV. A special prototype of a respective measuring device, called meniscus velocity sensor (MVS), has been developed to measure local free-surface velocity. In the present paper we describe experimental results of respective measurements in the model test stand LiMeSCo (liquid metal surface velocity correlation). To check the potential of the time-of-flight technique, in a first step we measure surface velocities during solid-body rotation of metallic substances. We observe that small modulations in the signals that are due to the natural unevenness of the solid body can be used to determine surface velocities. In a second step we apply the time-of-flight technique to liquid metal free-surface flow. Here we use the low-melting eutectic alloy GaInSn as a test melt. In this case we observe that the cross-correlations between the signals are much rarer and much weaker than in the solid-body experiments. We conclude that the presence of the localized magnetic fields, produced by the permanent magnets of the flowmeter, give rise to intense deformation of the free surface and the creation of surface waves. The field acts as a magnetic obstacle. We observe that the flow velocity is decreased right underneath the magnetic field and is accelerated in the side regions. This magnetic obstacle effect may restrict the determination of the local surface velocity in application.

Jan 1, 2012

By K. Yamaguchi

"This Precious metals content copper scrap is treated with a copper smelting process, and copper and precious metals are recovered. The precious metal lost in the slag is increasing with increasing of treated scrap amount. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. The distribution of precious metals between copper matte and FeOx-SiO2 slag phases is determined at 1300 oC and a fixed partial pressure of SO2 of 0.1 atm for the matte grades from 40 to 70 mass% of copper. The distribution ratios show a tendency to increase when the grade of matte is increased. In addition, the solubility of platinum and rhodium in the FeOx-SiO2-CaO slag under the air and the solubility of platinum in the FeOx-SiO2 slag equilibrated with a pure platinum or the Pt-Cu alloy were determined at 1300oC in the range of oxygen partial pressure from 10-9 to 10-7. The solubility of platinum and rhodium in the slag tends to increase with increasing content of copper in the slag and oxygen partial pressure. INTRODUCTIONThe stringency of the supply and demand of platinum group metal (PGM) intensifies by localization for resources and increase of the demand for PGM, furthermore, smelting and the recycling of PGM in the nonferrous smelting process take an important role. Scrap containing a precious metal for the purpose of collection of PGM is treated by copper smelting recently. With increase of the treatment amounts, loss of PGM in slags is the serious problem.In considering of PGM loss in slags, knowledge of the distribution behavior for PGM between slag and matte phases or slag and copper phases and the PGM solubility in slags is important. The distribution ratios of silver and gold between the FeOx-SiO2 slag and the Fe-Cu matte were reported by Roghani (Roghani et al., 2000), Shinha (Shinha et al., 1985) and Takeda (Takeda et al., 1993) However, there is no data for the PGM distribution ratio. On the other hand, the PGM solubility in slags was reported by Sano (Sano et al., 1997) However, there is very few report for the solubility of PGM in the nonferrous smelting slags."

Jan 1, 2012

By Thiago Ribeiro Abdou

O presente trabalho visa caracterizar um compósito polimérico de matriz epóxi reforçado com fibras de carbono HTS40 E13 3k TohoTenax® para avaliar o potencial de reutilização das fibras de carbono. As técnicas de caracterização utilizadas foram a microscopia eletrônica de varredura para análise superficial do compósito antes e depois da degradação térmica, análise por Energy Dispersive Spectroscopy para verificar os elementos químicos presentes no produto final e a termogravimetria para determinar a influência da temperatura e do tempo de tratamento na degradação da matriz polimérica. O presente estudo mostra que a matriz polimérica do compósito utilizado inicia o processo de degradação a 250°C e que a 500°C é possível obter um material de reforço intacto e livre da matriz polimérica com apenas traços residuais da resina e o tempo de tratamento térmico em um patamar isotérmico não influencia a taxa de degradação.

Aug 16, 2017