Search Documents

By Andre R. Laplante

Gravity gold recovery can be of significant economic importance for gold copper ores that cannot be directly cyanided. Gravity is typically followed by flotation to produce a smeltable copper concentrate. Flotation tails gold values are often too low to justify a cyanidation circuit. Given this typical scenario, a very effective gravity circuit can yield higher overall gold recoveries (i.e. gravity + flotation), and also improve the NSR of gold. Typical scoping work, whilst well suited to investigate the downstream circuit, be it flotation or cyanidation, often overestimates ore variability to gravity recovery and fails to yield the data needed to predict plant gravity recovery and design the optimum gravity circuit. This presentation examines why typical scoping work fails to address gravity recovery adequately and shows how a standard test to characterize gravity recoverable gold (GRG) can provide the missing data. Case studies are presented and used to illustrate the concepts of recovery effort and aggressive gravity recovery.

Jan 1, 2000

By C. S. Cole

CO-CHAIRMAN CARTER S. Cole l-The stimulus of war definitely increases interest in the subject we are discussing at this Symposium. There have been, in the past, other symposia on this subject and there probably will be still others in the future, but I feel sure that this one will go down as one of the most important that have ever been held on the subject. In 1918 A.S.T.M. held a Symposium on Stress- Corrosion Cracking that was confined entirely to brass, because at that time few people were interested in the phenomenon as it applied to other metals. Again under the stimulus of war, we are gathered to discuss the subject, but this time brass alone is but part of our interest. It is interesting to note more papers on brass will be presented than there were in the 1918 session, but these brass papers, you will also note, comprise less than half our program. Aluminum, magnesium and

Jan 1, 1945

By V. Bredykhin

The efficiency of scrap processing depends firstly on reliability of information about its chemical composition. The paper presents the results of the investigation and development regarding solid copper alloy scrap in the range of lump size 40÷300 mm. Nowadays the sorting of lump scrap is done by two methods: 1. Sorting according to metals and alloys is done at places of scrap generation, and further till metallurgical processing each lot has its "certificate"; 2. Hand sorting of scrap is done according to the marks on solid items in special shops using proximate analyzers or manually by experienced workers. This sorting process is labor - consuming low efficient and involves mistakes. The informational method is a promising trend in the copper scrap sorting. The method is direct, i.e. as a result of sorting the chemical composition of each scrap lump or main elements is determined, and assured data of qualitative and quantitative composition are received.

Jan 1, 2006

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information the obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of address, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1939

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information the obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of address, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1936

By P. Whincup, T. Showell, B. Marchant, R. Dunne

An oversupply of copper on world markets in the early 90' s, coupled with a decrease in demand, resulted in a "tight" market for the sale of copper concentrate. In these conditions small producers of low grade copper concentrates found it difficult to sell their products. The situation was exacerbated for those producers also having reasonable quantities of penalty elements (e.g. As, Bi). The Telfer Gold Mine bulk copper gold concentrate, produced from treating underground sulphide ore, fell into this category (i.e. 16% to 20% copper, 30% to 35% sulphur and 3500ppm to 4500ppm arsenic). The concentrate sulphide minerals are predominately chalcocite and pyrite. Although a higher grade copper concentrate was attainable a substantial decrease in gold recovery ensued. Under the prevailing market conditions a decision was made to stockpile concentrates pending either an easing of market conditions or alternatively finding an on site method for treating the concentrate to recover both the contained gold and copper.

Jan 1, 1995

By Anne Lemnitzer

Experimental data are the cornerstone of scientific research, providing empirical evidence to validate hypotheses, test theories, inform decision-making and help develop innovative design and analysis methods. However, beyond traditional empirical validations, experimental data have also become the most crucial component of AI algorithms, measuring the algorithms' effectiveness, and allowing engineers to ensure their reliability and applicability. The DFI "Rock Socket Project," awarded in the spring of 2018 allowed for the indispensable, experimental data-based validation of structural shear magnitudes, which have been hypothesized and discussed for years within the deep foundations community and cautiously approached by many design engineers. The fundamental project idea, i.e., the investi- gation of pile shear magnitudes through experimental research, was sparked during a heated discussion in the October 2016 Drilled Shaft Committee meeting in New York. Should we design for amplified shear at the rock socket of a drilled shaft or is this merely an artifact of the p-y design approach? Data were needed to provide consensus.

Nov 1, 2023

By Ch. Wenzl

Anodes must have a certain physical and chemical quality in order to provide uniform anodic corrosion and meet the requirements of electrorefining, i.e. to achieve a high current efficiency, low energy consumption, low amount of anode scrap and low effort together with high cathode quality. Various properties of the anodes can be influenced directly by the casting process, which is the interface of pyro- and hydrometallurgy of copper. The aims of anode casting ? high output and long mould lifetimes ? are not consistent with good physical anode quality. The physical requirements of an anode are smooth surfaces, uniform weight and thickness, minimal edge effects, minimal distortion of the body and the lugs, as well as a homogeneous microstructure, in order to achieve uniform dissolution behaviour. The chemical quality of the anode copper is a task of electrorefining operations, but the elemental distribution within the anodes, which should be as homogeneous as possible in order to provide uniform anodic corrosion, can be influenced by the casting process.

Jan 1, 2007

By L. A. Cornish, B. Eatwell

Austempered ductile iron (ADI) is a ductile iron which has had its matrix toughened by an austempering process. The alloy exhibits remarkable properties, which it owes to a unique microstructure comprising graphite nodules embedded in a matrix of acicular ferrite and carbon-enriched austenite. The properties include high strength combined with high toughness and ductility. Excellent wear resistance is also exhibited because, under strain, the austenite is transformed locally to martensite. Samples of ductile iron were austempered to produce grades I and IV AD!, and were tested at various strain rates. The grade IV ADI exhibited higher strengths and lower difficulties, and the strengths were found to be more dependent on strain rate. Transformation to martensite was more prevalent at the lower strain rates. A mechanism of increased flow stress and work hardening in the austenite of the matrix is proposed to explain the higher strength of the samples at high strain rates, where significantly less martensite is formed in the matrix.

Jan 1, 1995

As part of the response to the increased demand for products such as iron ore, coal and gold many resource companies have identified the need to develop strategies focused on attracting high demand professionals and retaining current employees in the business. Recent graduates are entering a time where they can expect high starting salaries, attractive benefits and lifestyle options. At the same time high work expectations and large demands on both personal and professional development will also be the norm. Some of the challenges faced may include high demands on performance, working with limited resources, long hours, and tackling unfamiliar areas of work with little guidance. However, managing your career and these challenges effectively can give you valuable experience in a short amount of time. By offering situations from my relatively short, yet active, career in the mining industry during these boom times I will raise some key points on how to best leverage your commodity and make the most of a bullish market.

Jan 1, 2006

By Peter Stubbs

Mr. Agelopas is to be congratulated on a fine paper. Although the presentation was simple and concise, you will all appreciate that a great deal of hard work went into the development of this highly successful repair method. Earlier this year Bethlehem invited a group of our people to witness lug repairs at their Sparrow's Point plant. We have since made lug replacements on a trial basis using their method. The repaired moulds are now back in service. We will compare their performance with regular moulds and with moulds repaired by a technique developed by Dofasco weld shop personnel. I would like to explain briefly some of the various types of ingot mould repairs presently undertaken at Dofasco. The first problem will be familiar to most of you. The lower inside edge of a mould wall may be damaged by spalling, a runout or by the washing action of steel deflected from a badly worn stool cavity. We repair this type of damage by welding.

Jan 1, 1972

By E. J. Magri

For life-of-mine planning, as well as for short- and medium-term planning of grades and mine layouts, it is extremely important to have a clear understanding of the patterns followed by the distribution of gold and uranium within the mining area. This study is an attempt to reconcile the geostatistical approach to the determination of ore-shoot directions, via an analysis of the spatial distribution of gold and uranium values, with the sedimentological approach, which is based on the direct measurement of geological features. For the routine geostatistical estimation of ore reserves, the Hartebeestfontein gold mine was divided into 1I sections. In each of these sections, the ore-shoot directions were calculated for gold and uranium from the anisotropies disclosed by geostatistical variogram analyses. This study presents a comparison of these results with those obtained from direct geological measurements of paleo-current directions. The results suggest that geological and geostatistical studies could be of significant mutual benefit.

Jan 1, 1978

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name in American Institute of Mining and Metallurgical Engineers, Incorporated; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses and a Library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1937

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1932

Mrs. W. Y. Westervelt, Director of the New York Section, reports an interesting meeting at her house- on May 12. Dr. Cecile Griel, special worker of the division for work among foreign-born women of the National Board of the Y. W. C. A., spoke. As the Americanization Committee under Mrs. Scobey is planning an energetic campaign, Dr. Griel's stirring appeal was timely and suggestive. While Dr. Griel cited the usual avenues of approach to our alien population through the school children, the needs of the baby, sewing classes, English classes, etc., her especial appeal was for correct psychology on the part of the workers. She deplored the condescension, implied or expressed, so often manifest in persons attempting Americanism, work and emphasized many times the importance of an understanding heart and mind. At the close Mrs. Scobey brought forward plans for practical work to be done by the New York women, of which I hope to give some details next month.

Jan 7, 1919

The methodology (i.e. procedures) used in testwork for modifying, improving, selecting, designing or developing processes is reviewed and possible improvements described. Minerals and particles could be characterised more comprehensively with modifications of existing procedures. Identification of the dominant phenomenon in a process could help bring the results of laboratory tests closer to plant performance. Improvements in pilot plant testwork could reduce the frequency and magnitude of problems in materials handling and separation in production processes, and increase the quantity and quality of the data obtained from a limited number of tests. Longer-term improvements in methodology depend on some changes in basic research. Information is required about all of the phenomena that occur in a production process rather than sophisticated models of specific phenomena. Theories, correlations and computer simulations could be used more effectively in testwork if they were simple, capable of forecasting the effects of changes and applicable to a number of similar processes.

Jan 1, 1986

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By Yu Yamashita

There have been increasing in melting recycled scraps in copper smelting processes, and thus growing interests in the chlorine behavior. In this study, chloride dissolution in FeO-Fe2O3-SiO2slag (SiO2sat.) at 1523 K has been measured with varying in PCl2 from 1.13x10-8 to 1.30x10-7atm. and the oxygen partial pressures encountered in typical copper smelting furnace, i.e. PO2=10-8 to 10-10 atm. Discussion is made on the chloride capacity of FeO-Fe2O3-SiO2 slag in terms of its characteristics and the dissolved chlorine species. It has been shown that the mostreasonable dissolution reaction and chloride capacity can be expressed by the following reactions, where chlorine dissolves in the form of Cl-; here, aO2-, oxygen ion activity, is shown a function of oxygen partial pressure in the atmosphere. [ ]

Jan 1, 2006

By E. Yigit

In the flotation process the physical factors such as agitation intensity air flow rate and pulp solid concentration are very important parameters affecting grades and recoveries of the products. The flotation tests were performed on the samples of Bigadic colemanite ore to investigate these factors at different agitation intensities ranging from 1000 rpm to 1400 rpm and air flow rates from 1000 cm3 ? min-1 to 2000 cm3 ? min-1 with 2 L and 4 L cells using Denver laboratory flotation machine. The tested collectors were Cytec Aero 825, Aero 848N and their mixtures. Agitation intensity and air flow rises resulted in more floated material although sometimes being not selective. These effects can be attributed to powerful collisions between air bubbles and mineral particles. The first observation was the effect of pulp solid concentration on the floatability of minerals, while the flotation in 2 L cell (0.125 g.L-1 solid concentration) at 1000 rpm (0.176 wattcm-3), and with 1000 cm3.min-1 air flow rate was possible, the flotation in 4 L cell (0.0625 g.L-1 solid concentration at 1000 rpm. (0.176 wattcm-3) and with 1000 cm3 ? min-1 air flow rate was not possible. However at 4 L cell after increasing agitation intensity to 1200 rpm (0.201 wattcm-3) keeping 1000 cm3 ? min-1 air flow rate, flotation was possible again. This shows that these factors such as agitation intensity have some critical role on flotation. Another interesting observation was on the selective effect of pulp solid concentration. In the flotation with 1 L cell at different agitation intensities, collector Aero 848N was selective against calcite, while in the flotation with 2 L cell at different agitation intensities the same collector Aero 848N was selective against colemanite.

Jan 1, 2014

By T Ireland, B Wright, S Weaver

All tunnels have unique characteristics that result in different fire and life safety risk. The fire safety systems for each tunnel also give different benefits at different costs. It is therefore neither pragmatic nor cost-effective to prescribe specific fire standards requirements for all tunnels. Each tunnel needs to be assessed individually but using a common process.The owner/client is normally the risk owner and needs to make the decision on what fire and life safety provisions will be provided within the tunnel. To make this decision they need to be appropriately informed. The low probability and high consequence nature of fire events creates a challenge such that traditional analysis processes, which tend to focus on a major event after it has happened, are not easily applied and do not give the best value for money. Therefore a process is required that provides the relevant information to the owner for decision-making.A quantitative risk assessment (QRA) provides a process and framework for the consideration of fire life safety risk when applied properly. This involves a risk assessment of the ‘do nothing’ option together with assessments of improvement options and their costs. It also involves consideration of benchmark safety levels for other tunnels and the open road.This paper will outline a QRA process for assessing fire and life safety risk in tunnels and how this has been used for three existing tunnels, Homer Tunnel, Lyttelton Tunnel and Mt Victoria Tunnel. Key challenges include determining an acceptable safety level, defining realistic inputs, providing sufficient complexity to get meaningful results but not so complex that transparency is lost and interpretation to enable decision-making by non-technical personnel.CITATION:Weaver, S, Wright, B and Ireland, T, 2014. A transparent and pragmatic quantitative risk assessment process for assessing fire safety in New Zealand tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014