Search Documents

By C. D. Dolman

Since the outbreak of the war we have discovered in the united States minerals of which there was no general knowledge, and which compared very favorably with anything that could be found in any foreign country. One of these was magnesite, or the carbonate of magnesium as it occurs in nature. This mineral crystallizes in the rhombohedra1 form, has a specific gravity of 3.00, molecular weight of 84.4, molecular volume of 28.1, and a hardness of 3.5 to 4.5.1 Had it not been for the development of the California deposits of this mineral and the discovery of immense new deposits in Stevens County, Wash., the production of steel during the war would have been more seriously handicapped than it was. Now that the war is over, we face the possibility of competition with the cheap Austro-Hungarian magnesite; and while that may not be so cheap as it was before the war, adequate protection should be given the producers in this country to insure the full development of our own resources. The consumption of magnesite in the United States in 1913, the year preceding the war, was 172,591 tons of calcined and 22,872 tons of crude magnesite. Less than 3 per cent. of this amount was produced at home. At the present time, practically all of the magnesite used in the United States is produced at home. Expensive plants have been constructed, extensive exploration work done, and production pushed to the utmost to supply the necessary requirements of the war. Thus a considerable industry has been built up within our borders. Some magnesite has been imported from Canada and Mexico, but the Canadian ore was of an inferior grade and could not be used satisfactorily. During the year 1918, production decreased in both the United States and Canada; the production in the United States was 225,000 tons in 1918 as against 315,000 in 1917, and in Canada 39,365 tons in 1918 as against 58,090 in 1917. This decrease was mainly due to over-production during 1917, the domestic demand being only 300,000 tons. The material produced and sold in the United States must contain, in the crude form, not more than 3.5 per cent. silica and 2 per cent. lime;

Jan 1, 1920

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By Guoming Lin, Yan Jiang

The Hutchinson Island ferry landing, a vital transportation hub located between the Savannah Convention Center and Westin Hotel, faced a critical infrastructure challenge on June 18, 2022, when the sheet pile bulkhead along the Savannah River experienced movement, resulting in a substantial crack in the brick-paved plaza.  Immediate monitoring efforts commenced within two hours of the bulkhead disturbance, revealing progressive movements over the subsequent two weeks, leading to approximately ten feet of deflection and six feet of settlement behind the bulkhead.  Subsequent repair work involved the extraction of 65-ft-long steel sheet piles. This investigation embarked on a meticulous review of the original design and construction procedures, followed by a comprehensive subsurface exploration program.  The steel sheet piles were originally supported by drilled helical anchors, and the failure mode and pattern were closely scrutinized.  Analysis of the pulled-out sheet piles revealed consistent shape and yield points.  Computer modeling was conducted to replicate the actual deflection profile and yield point as verification of the soil parameters and design models. This paper presents the investigative findings, including an analysis of subsurface conditions and the most probable causes for the bulkhead failure.  The results of the investigation have been instrumental in formulating design recommendations for the repair of the bulkhead system.  By shedding light on the root causes of the failure, this research contributes valuable insights to the soil-structure interaction in the steel sheet pile design. Top of Form

Oct 7, 2024

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020

By G. F. Comstock

These notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."l In that paper and the resulting discussion, several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8-in. (9.5-mm.) steel plate, about 21/4 by 13/4 in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extended through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what Mr. Miller called cem-entite and Mr. Jeffries martensite, while Mr. Ruder and Professor Boyls-ton think that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Pig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1920

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Herewith are submitted the report of the Treasurer for the year 1936 and the reports for the same year of the following committees: Admis¬sions, Membership, Papers and Publications, Library, Student Relations, and MINING AND METALLURGY. To these reports you are referred for details of the year's activities. Finances.-Income for the year was $173,091 including an appropria¬tion of $2500 from the Rocky Mountain Fund earmarked to defray expense for official visits to western Sections and student societies. This compares with $141,754 in 1935 and exceeds by more than $50,000 the income of 1933 wherein the low point during the depression was reached. The major items of increase were: $6,700 from current dues; $10,600 in initiation fees and dues of newly enrolled members; $10,800 from the monthly magazine MINING AND METALLURGY. Sundry small declines were offset by minor increases. Expenditures for the year totaled $176,007 compared with $148,361 in 1935. Major increases were $5,700 for MINING AND METALLURGY; $4,000 for TRANSACTIONS and TECHNICAL PUBLICATIONS; $1,500 for meetings; $1,300 for Local Section appropriations; $6,500 for Technical Division expense; $5,000 for Increase of Membership expense; and $2,500 for visits to Local Sections and educational institutions. Comment on several of these items will appear under subsequent heads. Net deficit for the year was $2,915, this sum being made up from the accumulated surplus. It is interesting to observe that the net excess of income over outgo for the five-year period 1932-1936, inclusive, is $760. Membership and Dues.-During the year there was a net gain in membership, including Members, Associates, Junior Members and Junior Foreign Affiliates of 755 (from 7116 to 7871). In addition there was a gain of 616 in Student Associates (from 1004 to 1620). Taking account of small losses totaling 5 in the other grades, the net increase was 1366 bringing the total to 9607, the highest figure reached in the history of the Institute except at the end of 1921 when the total was 9850. In part the gain is accounted for by the smaller number lost by suspension

Jan 1, 1937

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By Demetrius Da Rós Ruy

O lingotamento contínuo é uma das etapas mais importantes na produção de aço, sendo um método rápido e eficiente na fabricação de placas ou tarugos através de processos de resfriamento onde o aço líquido é moldado e solidificado. Contudo, têm sido historicamente observado problemas de processo corrosivo acentuado na câmara de exaustão e na estrutura das máquinas da ArcelorMittal Tubarão. Os mecanismos deste processo corrosivo em máquinas de lingotamento contínuo, em geral, são variados e diretamente relacionados às condições operacionais da máquina, conduzindo a elevados custos de manutenção, diminuição da vida útil das máquinas, causando insegurança e interferindo na qualidade do produto. Este trabalho objetiva descrever as causas principais deste processo corrosivo e mostrar o desenvolvimento de testes que foram conduzidos visando a minimização deste fenômeno na máquina de lingotamento de placas #1 da ArcelorMittal Tubarão no ano de 2017.

Oct 30, 2017

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By G. L. Myers

The Fortitude skarn near Battle Mountain, NV is currently one of the largest producing gold skarns in the world. It contains about 11 Mt (12 million st) of minable ore grading 5.14 g/t (0.149 oz per st) and is the distal portion of a continuous skarn system in the Copper Canyon area centered on the Eocene Copper Canyon granodiorite porphyry. Calcsilicate compositions, opaque mineralogy, and the high gold grades are atypical of other base metal skarns (iron, Fe; copper, Cu; lead-zinc, Pb-Zn; or tungsten, W). The Copper Canyon skarn is systematically zoned from a garnet (AD 70-100) dominant, pyroxene (HD 20-45) subordinate zone, with major Cu mineralization, adjacent to the intrusive (West ore body), to a pyroxene (HD20-100) dominant, garnet (AD90-100 cores. AD 30-60 rims)subordinate assemblage, with major Au, near the distal marble front (Fortitude ore body). An extensive biotite ± diopsidic pyroxene ± kspar alteration halo surrounds the pyroxene > garnet gold-bearing skarn and represents the early stages of metasomatic alteration. Retrograde alteration is limited in areal extent and intensity, and consists of actinolite, chlorite, quartz, and prehnite. Economic gold mineralization begins in the pyroxene > garnet zone and continues to the marble front, a distance of 1 to 1.5 km (0.6 to 0.9 miles), respectively, from the plutonic contact. The opaque mineralogy in this gold zone includes pyrrhotite, arsenopyrite, marcasite, minor chalcopyrite, galena, sphalerite, argentite, hessite, hedleyite, volnyskite, and native bismuth and gold. The pyrite-pyrrhotite geothermometer yields temperatures that range from 450° C to 300°C (842° F to 582° F) and the electrum-argentite-sphalerite geothermometer yields temperatures which range from 290°C (554° F) at the marble front to about 420°C (788° F) more proximal to the intrusive. Log fS2 calculations from the sulfide assemblages yield values near - 10 with log fO2 values of about -30, in a solution of near neutral pH (5-6). Calculations of metal solubility suggest that the metals were transported as chloride complexes in the proximal skarn but that bisulfide complexes were predominant within the distal gold skarn. Relatively low oxidation states buffered by the carbonaceous to argilliceous, calcareous protolith and subsequent ferrous iron-rich skarn assemblages appear to have increased the gold carrying capacity of this large hydrothermal system.

Jan 1, 1991

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck' reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.' The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By A. V. Tarasov

In order to improve technical, economic and environmental performance of hydrometallurgical processing of intermediate products containing copper and nickel, the Gintsvetmet Institute and the IMET Institute of the Russian Academy of Sciences have conducted studies into the efficiency of the use of alternating current of industrial frequency on processes applied for hydrochemical leaching of various copper- and nickel-containing materials. It has been found that: 1.Imposition of alternating current over the process of leaching of softly reduced nickel oxide with recycled copper sulfate solutions resulted in an increase by 20 to 30% of the rate of the copper cementation process and reduced by 20% its activation energy. At the same time, the recoveries of nickel, cobalt and iron to the leach solution increased up to 82.2%, 78.5% and 57.1%, respectively, and that of copper to the cement precipitate up to 74%. Optimal process conditions have been identified with respect to the current density, electrode material, copper concentration in solutions and the process temperature. 2.In the process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides, the grain size, the phase form of sulfides, the solution composition (H2SO4, Cl?, Cu2+, Fe3+)and the current amperage had an effect on the nickel recovery to the solution, which reached 90%, while the degree of copper transfer to solution did not exceed 20%. The process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides with an addition of Cl? made it possible to selectively recover nickel into the leach solution along with concentrating copper in the leach residue. 3.When subjecting samples of commercial-grade magnetic fractions of converter matte to sulfuric acid leaching, the imposition of electric current, the concentrations of sulfuric acid and chloride ion in the solution and the duration of the reaction process had an effect on the process. The nickel recovery was 85% and that of cobalt and iron was 95% and the recoveries reached 97.5%, 98.3% and 99.8% as a result of repeated treatment of the primary residue under similar process conditions. Up to 75% of copper, 75% of sulfur and 99.0-99.5% of palladium was concentrated in the solid reach residues. The experimental data obtained indicates that the use of AC for hydroelectrochemical sulfuric acid leaching for separation of copper- and nickel-containing intermediate products has favorable prospects.

Jan 1, 2003

By G. C. Broadhead

THE lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top 1. Sandstone (the second of Missouri geologists), - 20 feet. 2. Cbert beds-beds of passage below, - 125 feet 3. Magnesian limestone, chert, and quartzite, - 100 to 300 feet 4. Lower magnesian limestone, - 100 to 150 feet 5. Gritstone and lingula beds, - 50 feet 6. Ozark marble beds, - 5 to 20 feet 7. Sandstone and conglomerate, - 5 to 90 feet 8. Porphyry, Archaean. 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as de¬tached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have pene¬trated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous sandrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called u mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

Jan 1, 1877

By G. C. Broadhead

The lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top: 1. Sandstone (the second of Missouri geologists),.... 20 feet. 2. Chert beds—beds of passage below,...... 126 " 3. Magnesian limestone, chert, and quartzite,. .. 100 to 300 " 4. Lower magnesian limestone,......100 to 150 " 5. Gritstone and lingula beds,....... 50 " 6. Ozark marble beds,........5 to 20 " 7. Sandstone and conglomerate,. .. .. 5 to 90 " 8. Porphyry, Archæan 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as detached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have penetrated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous saudrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called " mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.