Search Documents

By John E. Riddell

This review is based on a questionnaire sent out in 1959 to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geo-chemical techniques in Precambrian terrains. Of the companies questioned, 21 returned completed questionnaires and of these, 15 companies stated that they had some experience in this type of work. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only three have reported that they do not use applied geochemistry at all. The others have reported that they make use of applied geochemistry in New Brunswick and in the Cordillera in areas of light glaciation. Their opinion is that it is a useful aid when accompanied by other techniques in evaluating mineralized areas. GEOCHEMICAL SURVEYS Table I reviews the type of geochemical surveys used by these companies, and the following points of interest should be noted.

Jan 11, 1960

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By J Fraser, M Scoble

Within the past decade, incidents of mining–community conflicts have grown dramatically and represent one aspect of a phenomenon known as social risk. Research published in 2014 indicates that a lack of social acceptance is now a leading and costly cause of delays for mining projects.The rise of social risk, complemented by the need to earn the trust of an increasing number of stakeholders so that mining projects can be developed effectively, is problematic for the industry. Conflicts are occurring in situations where companies are fully compliant with regulatory and legal requirements, despite initiatives by mining companies to earn social acceptance and despite the proliferation of tools to support corporate social responsibility. Intensifying the impact of social risk is the fact that it has increased during a time in the global mining sector when companies have had to grapple with declining commodity prices, increasing capital costs and debt levels and the challenges of mining lower-grade deposits.This paper will explore a hypothesis that in today’s interconnected society, social risk in the mining sector constitutes a legitimate business risk that must be managed strategically. The reality facing mining companies is that information, once considered confidential, now travels quickly on social networks and via a growing number of groups and individuals that have earned a legitimate right to be classified as stakeholders in projects that affect their communities. To be successful, it is suggested that companies will benefit from increasing internal collaboration and providing training to equip teams to mitigate social risk to mining projects and protect reputation capital. The paper is based upon PhD research being undertaken to assess the points of intersection between social risk and social responsibility during the construction stage of greenfield mining projects.CITATION:Fraser, J and Scoble, M, 2015. Mining–community conflicts – can the future mining sector transform social responsibility?, in Proceedings Third International Future Mining Conference, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T. Wohlford

Due to the increases available base of scientific knowledge, increased independent review required by worldwide security exchanges, and the need for accuracy in characterizing mine water resources, it has become necessary to produce a more accurate hydrologic balance. This presentation provides a critical review of the steps and tools to compile a complete hydrologic review of a mine property. The forces of regulation, increased scientific analysis, better tools, and stakeholder expectations have created a perfect storm of accuracy demand. Ausenco has developed protocol to achieve the desired end.

Feb 23, 2014

By Alexandre de Freitas Gomes de Mendonça, Leonardo José Silva de Oliveira, Rodrigo Seara Martins, Rodrigo Madrona Dias

No lingotamento contínuo, o pó fluxante é responsável pela formação de uma escória líquida no molde que formará um filme de escória entre a placa de cobre e a pele solidificada. As principais funções do filme são lubrificar e moderar o fluxo térmico no molde. Em particular, para aços com tendência ao agarramento, objetiva-se uma escória que potencialize uma extração térmica mais intensa em relação às escórias aplicadas em aços com tendência à depressão. O índice de basicidade do pó fluxante é o parâmetro que afeta diretamente a resistência térmica do filme de escória e, por consequência, a espessura da pele solidificada na saída do molde. Com o trabalho investigativo das melhores práticas, reduziu-se o índice de basicidade em 16,8% dos pós fluxantes aplicados em aços ultra baixo carbono obtendo um aumento de até 10,1% no fluxo de calor no molde. Além do aumento na espessura da pele solidificada, esse resultado também influenciou na estabilidade do nível de aço do molde e na qualidade superficial de placa.

Oct 1, 2019

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By H. R. Babitzke, H. Kato, R. E. Siemens

An investigation was made to provide further information for evaluating columbium- hafnium alloys for use as high - temperature structural materials . The columbium- hafnium system was investigated between 700 ° and 2,400 ° C by melting point , thermal analysis , X - ray diffraction , electrical resistivity , and metallographic techniques . The equilibrium diagram is the beta isomorphous type , with columbium tending to stabilize the beta phase . Addition of 60 atomic percent columbium stabilizes the beta phase at 700 ° C. The allotropic transformation temperature of hafnium is 1,750 ° ± 20 ° C. A minimum melting point occurs near 75 atomic percent hafnium .

Jan 1, 1964

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By David R. Maneval

At the turn of the century the keys to industrial success were coal and iron. At that time, Pennsylvania was the ranking mineral producer among the States and close to 90% of the Nations energy output was generated by coal. The growth of this Common-wealth into the greatest industrial State in the nation has been due to the huge resources of easily accessable coal found by the early settlers. It was the development of these deposits that provided the United States with a new source of fuel energy. For nearly a century, the Commonwealth was the chief powerhouse of our nation and the chief source of its industrial blood and bone. In 1928 it was truly said that coal was king in Pennsylvania. Pennsylvania that year mined a billion dollars worth of coal. A single train carrying this output would reach more than twice around the world at the latitude of Pennsylvania. Coal formed nearly 67% of the freight of Pennsylvania and was responsible for its four billion dollar iron and steel industry. Coal was the real reason why Pennsylvania although 32nd in size was second and not tenth or fifteenth in wealth, population and industry. Pennsylvania was slow to take-up her heritage as the greatest coal producing State in the union. But the knowledge that coal was present was not slow in accumulating. In fact the Indians were aware of its existence long before the white man arrived. They knew that many of the hills were underlain with black stones that would burn. It is reasonably certain that Arnold Viele, the first white man to cross the mountain in this State saw coal in them in 1692. But awareness was not enough. The population in these days was confined to southeastern corner of the State and the population at this time had little need or interest in the resources further inland. Pennsylvania anthracite was discovered in 1762 but was first regarded only as a curiosity. Commercial productions started in 1820. This stimulated the development of many native industries and extensive canal system and afterwards an elaborate net-work of railroads were constructed at great costs to bring the products of the hard

Jan 1, 1971

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By FREDERICK MCAKCCOY

THE production of tin from Mexico has never reached the point of being considered a national industry, but the distribution of tin ores is so widespread that there are possibilities that one day it may become of importance. Of the twenty-seven states of the Republic, tin claims have been taken up in sixteen. In all there had been taken up to the end of 1926, two hundred and twenty-five claims, of a total area of about 7400 acres. The first historical mention of tin in the Americas is found in a letter of Cortez to the Emperor, Charles the Fifth, of Spain, which is as follows: Speaking of his manufacture of some small cannon, he says: "For these reasons I took considerable pains to get copper from some provinces of this country, and bought it at a high price in order to get it quicker.

Jan 1, 1929

By B Tutmez

Determination of stress-strain behaviour of rocks plays a crucial role in understanding the response of rocks during loading. However, it is a tedious, expensive and a time-consuming process to obtain such characteristics both in the laboratory and in situ. On the other hand, non-destructive testing methods such as ultrasonic velocities can produce a reliable and fast solution to indentify state of strain and stress in rocks. The present paper aims to provide insight into the relations amongst ultrasonic wave velocities, amplitudes and deformability properties of porous siltstone under compressive loading. For this purpose, pulse (vP) and shear wave velocities (vS) along with amplitudes (AP - AS), and applied loads with resultant strain were measured simultaneously so that response of siltstone to compression can be evaluated. In addition, initial vP and vS were recorded at the beginning of each test to calculate dynamic elastic properties of the specimens. This provided a comparison between static and dynamic elasticity properties of siltstone. Crack damage associated with the onset of dilation was also investigated. The results showed that there is a non-linear logarithmic relation between velocities and stress-strain level for siltstones.

Sep 26, 2011

By Sherwin F. Kelly

NEW trend in geophysics has been uncovered in these depression years, made evident through the thinning cloak of commercial activity, which, in better times, would have completely obscured it. I refer to the increasing use of these methods for geological investigations by federal and state geological surveys. This is a trend that has been gathering momentum not alone in the United States, but abroad as well. Thus, in Poland, the Geological Survey has been playing an increasing role in geophysical work since 1927, and now has- its own geophysical department. The government petroleum producing organization of Argentina has its Geophysical Commission; Brasil boasts a completely equipped geophysical department in its Mineral Production Service; the government of Chile has contracted with commercial companies for geophysical surveys; Peru is planning an intensive program of geophysical prospecting in its petroliferous regions; and Canada has, for several years, cooperated with

Jan 1, 1935