Search Documents

By Waldemar W. Koczkodaj, William O. MacKasey

A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simpli?ed case of volcanic-associated massive sul?de type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of non-measurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to re?ne at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By Craig M. Shillaber, Joseph E. Dove, James K. Mitchell

"This paper addresses two primary factors affecting the sustainability of Deep Mixing Methods (DMMs): construction materials and handling of the spoil from wet mixing methods. We examine these factors within a life-cycle embodied energy (EE) and carbon dioxide (CO2) emissions accounting framework, using the LPV 111 project in New Orleans, LA as a case history. The underlying assumption is that project planning and preliminary design have determined that a DMM is the best ground improvement alternative for achieving the broader aims of sustainable development. While EE and CO2 emissions are direct measurements of environmental impact alone, we illustrate how their minimization can also influence the social and economic consequences of the project. It is recommended that DMMs use lower energy and carbon material alternatives to Portland cement and lime in the binder whenever possible, with preference given to locally sourced materials. Currently available alternative cementitious materials include fly ash and slag, which are waste products from other processes. In addition, recycling the spoil material from wet mix methods on site is recommended. If the material cannot be recycled on site, transporting it to a processing and recycling center for later use as fill is preferred over landfilling. INTRODUCTIONWithin the geotechnical community there is an increased appreciation for sustainability considerations, which are an important component of the planning, design, construction, operation and maintenance of projects. An assessment of project sustainability includes holistic life cycle thinking, systems analysis, environmental impact assessment, use of safe and benign materials, awareness of local societies and cultures, social equity, protecting human health and well-being, and monetary costs (Abraham, 2006). Since ground improvement is a principal practice domain of geotechnical engineers, it is important that geo-professionals play a role in addressing the sustainability for these projects. In this paper, we illustrate by case history how different materials and methods associated with deep mixing projects can impact overall project sustainability through quantifying project embodied energy (EE) and carbon dioxide (CO2) emissions. EE is defined as all energy consumed to bring something into its present state (Chau et al., 2008; Inui et al., 2011; Soga et al., 2011; Chau et al., 2012). Recommendations are then made for how adverse environmental impacts of Deep Mixing Methods (DMMs) may be minimized, leading to more sustainable geotechnical construction."

Jan 1, 2015

By K. Perry, B. Lusk, Q. Huang, R. Honaker

"Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. The application is conducted either dry or wet. Both methods have advantages and disadvantages however the formation of caked rock dust particles is cited as a significant concern for wet applications. A study was conducted to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid (OA) and sodium oleate (NaOL). At a NaOL dosage of 2 lbs/ton, a contact angle of 112o was measured indicating strong surface hydrophobicity and ability to repel water. FTIR studies indicated a chemisorption mechanism which is necessary for long term stability of the surface modification. The dispersion rate of the modified rock dust samples was elevated by the application of both OA and NaOL thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed a 79% reduction in the dust explosion potential relative to untreated rock test applied by the wet technique. INTRODUCTION Mine explosions have been a long-time threat to underground coal miners attracting significant attention to the accumulations of combustible dusts and gasses. In the presence of sufficient oxygen and heat, the accumulations of combustible dust and gass can lead to large-scale underground coal mine explosions [Harris et al., 2010]. To alleviate the problem, rock dust such as limestone can serve both as a thermal inhibitor and a heat sink to inert the coal dust explosibility thereby prohibiting the occurrence of dust explosions [Richmond et al., 1975; Amyotte et al., 1995; Dastidar et al., 1997; Man et al., 2009]. The dispersibility of the rock dust is an important characteristic that determines the degree of explosion prevention [Greenwald et al., 1938; Mozumdar et al., 1974; Amyotte et al., 1995]. Unfortunately, the environmental conditions of an underground mine has the potential to cause caking of the rock dust which reduces the dispersive characteristics needed. The dispersive property of rock dust can be enhanced by modification of the particle surface properties by the application of chemical additives [Greenwald et al., 1938; Mozumdar et al., 1974; Spence, 2004; Vogt, 2011; Doidge et al. 2014]. The major mechanism for rock dust caking is the adsorption of water which forms liquid bridges at the particle-particle contact points where saturated solutions of soluble powder ingredients are present. Changes in temperature or relative humidity result in solvent (water) evaporation and the formation of dry bridges [Rumpf, 1958; Specht, 2006]. One method to prevent caking is creating hydrophobic rock dust to repel water from the solid surface thereby preventing the formation of liquid and solid bridges."

Jan 1, 2015

This paper presents a theoretical investigation on the ionic equilibrium of Fe(III)?Ni(II)?H2SO4?H2O system. A non-ideal speciation model is developed to calculate the concentration distribution of iron and nickel species in a mixed ferric and nickel sulphate aqueous solution over the pH range from 0 to 4 and temperature from 25 to 100°C. A series of speciation diagrams for iron and nickel species is plotted with the effects of ionic strength and temperature on the equilibrium constants being taken into account. The ionic strength-dependent equilibrium constant is treated through a semi-empirical Vasil'eV equation, which is based on an extended Debye?Hückel theory. A Helgeson model is applied to extrapolate the equilibrium constant to elevated temperature. The ionic equilibrium reactions are described by a group of numerical equations containing the temperature and ionic strength-dependent equilibrium constants, which are solved by the Newton-Raphson method. The speciation model is also applied to estimate the hydrogen ion activities and corresponding pH values. The calculated pH values are in agreement with the experimentally measured pH, and are compared to literature data and pH values produced by the Visual MINTEQ® program (a computer code for the calculation of chemical equilibrium in natural aqueous system). This investigation provides a deep insight into the ionic equilibrium behavior of a mixed metal sulphate aqueous system which commonly occurs in hydrometallurgical processing. Keywords: speciation, chemical modelling, thermodynamics, iron, nickel

Sep 1, 2012

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021

By Jim Pae Lem

This study investigates the mode of occurrence of uranium in a copper concentrate from the Prominent Hill mine. Mineralogical and liberation studies of a high grade Cu concentrate (monthly composite) containing uranium (U) were undertaken using QEM-Scan in combination with QXRD and ICP-MS. The study aimed at determining in what form U was recovered, and by which mechanisms. The deportment of U was studied in 3 size fractions; +20µm, -20+8µm and -8µm. QEM-Scan analysis showed that uranium was present as U(Cu)-silicates, U-silicates, UPbOx/FeOx or traces of UThOx and UTiOx, with the U-silicates present across the size fractions. The association of uranium bearing minerals with copper sulphides varied across the size ranges. Interestingly, most of the U (46% by weight) was distributed in the finest fraction (-8µm), in which the deportment of Cu was low (6%). Over 40% of the U mineralisation in the -8µm was liberated. In terms of the floatation response, while recovery of the uranium minerals as a result of their association with copper sulphides (as composite particles) was evident, recovery of UPbOx locked in hydrophilic haematite in the +20µm size fraction suggests, that other mechanisms (e.g. Inadvertent activation by Pb from radioactive U decay) are possible. Furthermore, the high amount of fine liberated U bearing particles in the concentrate points at entrainment as another major mechanism for uranium recovery, and therefore, a target for process optimisation.

Sep 1, 2012

By Jorge Vargas

El macizo rocoso de Tintaya es un material complejo por la variedad de su litología. Por ello, es favorable la aplicación de la técnica del banco doble en zonas que anteriormente no eran hábiles. En ese sentido, el presente trabajo evalúa el uso de las técnias de bancos dobles durante el descenso de la Fases 2 y 3 en la mina Tintaya en la modificación por diseño de las alturas y ángulos de banco, de forma que el nuevo diseño propuesto conlleva ahorros con respecto al diseño anterior.

Sep 14, 2009

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By T. E. Bernard

"Refuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet the U.S. Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and management of heat from the occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements and carbon dioxide generation that are representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current U.S. coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in.) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in a refuge alternative. The highest likely metabolic heat generation ranged from 113 to 134 W, depending on occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 L (0.81 cu ft) of oxygen per hour per person and 20 L (0.71 cu ft) of carbon dioxide per hour per person, which means the margin of safety is 50 percent or more compared with the MSHA requirements. The information on metabolic heat generation can be used to assess refuge alternative thermal environments by testing or simulation. The required oxygen supply and carbon dioxide removal can be used to assess refuge alternative requirements. IntroductionRefuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet U.S. Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen (O2), removal of carbon dioxide (CO2) and management of heat resulting from the refuge alternatives’ occupants and mechanical/ chemical systems (MSHA, 2008)."

Jan 8, 2018

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By R Steinhaus, D M. Frantois-Bongarton, P W. Cleary, G K. Robinson, M D. Sinnott

Multotec Process Equipment and Dominique Frantois-Bongarton have a patent for a mineral sampling device, which they call a æTrue-Belt SamplerÆ. This uses a plough, which is rotated about an axis parallel to a conveyor belt to throw material off the belt. A fixed sample cutter takes a sample from the material thrown off the belt.Discrete element modelling has been used to consider a range of plough designs, plough speeds, positions for the cutter relative to the plough, cutter apertures, cutter designs and frictional properties, prior to the building of a physical prototype. This modelling work will be discussed, both as an illustration of the role of modelling in the development of new materials-handling devices and in order to explain the likely strengths and weaknesses of this new type of sampling device.CITATION:Robinson, G K, Sinnott, M D, Cleary, P W, Steinhaus, R and Frantois-Bongarton, D M, 2012. Modelling of a ætrue-belt samplerÆ - A new device for sampling from a conveyor belt, in Proceedings Sampling 2012 , pp 33-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By S. Durapraj, R. T. Masethe, U. Maqina, A. C. Adoko

This study investigates seismicity and rockburst control within the Merensky Reef and UG2 orebody of an intermediate-depth platinum mine located in South Africa's Bushveld Complex. Utilising a mine-wide seismic monitoring system, over 1,900 seismic events were recorded between April 2023 and May 2024, revealing complex seismic patterns driven by mining-induced stress changes. The largest event, with a magnitude of ML 2.0, underscores the seismic risks associated with mining at increasing depths. Key findings include the spatial and temporal variability of seismic events, with high seismic activity observed near pillars and geological structures. A significant portion of events correlated with pillar and foundation failures. Moment tensor analysis identified dominant failure modes, such as stress-driven fracture closures and dynamic pillar failures. To mitigate risks, the study emphasises advanced support system redesign and rockburst risk assessment using the rockburst damage potential (RDP) method. The research highlights the importance of monitoring, geotechnical compliance, and adaptive designs in enhancing safety and reducing seismic hazards in underground mining operations. The study applied the RDP framework, classifying damage across R1 to R5 scales, where most instances fell into low-risk categories (R1 and R3), indicating minor to moderate damage. However, data limitations and the tabular stoping method's complexity led to inconclusive results, highlighting the need for more robust data and customised risk assessment tools. Despite these challenges, the RDP approach provided valuable insights into rockburst mechanisms and the effectiveness of existing support systems.

Jan 12, 2025

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By K. Duffy, W. Valery, L. Pyle, P. Holtham

A conceptual scoping study was conducted to investigate pre-concentration options for upgrading ore from an Ag-Pb-Zn deposit. The low grade of the ore would result in only modest economic returns, given current market conditions. Several pre-concentration options were considered. These included: selective mining, crushing and pre-screening (following either standard or high intensity selective blasting), bulk ore sorting, particle sorting, jigging, dense medium separation, or combinations of these approaches. Flowsheets were developed for each option, and the upgrade performance was modelled using Limn to determine mass balances and stream tables. Due to the limited availability of test work data, the models were based not only on what test data was available but also on case study data found in the literature. The Bazin technique was used to derive assay by size data for different streams following crushing. Equipment lists and preliminary layouts were established based on the stream tables, and capital and operating costs were estimated for each flowsheet. This information was used to carry out a preliminary economic evaluation using net present value and sensitivity analysis. In this case, the most economically attractive process was found to be particle sorting; although further benefits may be realised by combining with bulk sorting. This paper describes the methodology used and the key findings of the study. Keywords: Pre-concentration, pre-screening, ore sorting, jigging, Ag-Pb-Zn, particle sorting, bulk ore sorting

Jan 1, 2020

By Hector O. Romero, Paulo C. Fernández A, Claudio C. Gajardo

Phase 06 of the Los Bronces mine, currently under extraction for development, has the particularity of being close to the installations and buildings of a neighboring copper mine. Therefore, the blasts must ensure the continuity of the operation without affecting the nearby structures of the neighboring district, which include Maintenance sheds and Warehouse. Specifically, the safeguards consider a scenario that includes: - Flyrock projections (<150m) - Edge profile studies - Vibrations according to the NCh3577 standard - Nitrous gases Additionally, Phase 06 is also within Los Bronces, so strict control over spillage into the pit is necessary to avoid blocking ramp access to this level. The challenge lies in protecting not only the operation and facilities of the neighboring mining district but also the operability of Los Bronces. Thus, addressing these considerations, blasting configurations are developed with prior simulation of vibration models, flyrock, and spillage in all blasts, with strict control of technical design and implementation to ensure the results. Currently, blasts are successfully executed with control of projections based on the proximity of the projects, vibration (<40mm/s) with decoupling of holes of 17 mm/s between holes, reactive rock tests for explosive selection (loading advancement), and spillage simulation inside the pit according to the loading design; thus, ensuring operational continuity and mine development.

Jan 21, 2025

By X Ling, M Barati, E Moosavi-Khoonsari

In the pyrometallurgical process of secondary lead recycling, a desulfurising agent, such as Na2CO3 is added to minimise the emissions of sulfur into the atmosphere, while silica is introduced into the smelter as a fluxing material. Subsequently, a significant amount of Na2O and SiO2 remains in the downstream reverberatory furnace and blast furnace slags. However, there is limited understanding of the thermodynamic behaviour of silicate-based lead slags rich in Na2O, posing challenges in accurately determining the optimal condition for targeted metal recovery and final slag composition. In this work, the equilibrium phase relations of the PbO-Na2O-SiO2 system in the primary phase field of Na2SiO3 are studied from 800 to 1000°C via equilibration-quenching method. Samples with different compositions were prepared and held in platinum capsules in air at these temperatures to reach equilibrium. The equilibrated samples were subsequently quenched and the phase compositions were measured by electron probe microanalysis (EPMA). The results were then compared to those of previous studies and any discrepancies were resolved.

Jun 19, 2024

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation&apos; of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,&apos;-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals&apos; force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.&apos; The streaming potential

Jan 1, 1970

By D. Stone, M. Le Roux, Q. P. Campbell, M. Fofana

Float-and-sink analysis is widely used in the coal industry to obtain washability data, yielding important information about beneficiation potential and performance. This method is associated with health and environmental problems, and research into alternative densimetric methods is important. The RhoVol is a new technology developed by De Beers Group Technology South Africa (DebTech) for the image-based generation of densimetric data from ores. The analysis is done on a per-particle basis, within a size range of +3 mm –8 mm. In this paper we compare the established methods used for the float-and-sink analysis of coal with a new method using RhoVol. The aim of the study was to determine the validity of the information obtained from the RhoVol analyser by performing comparative densimetric analysis on three different coal samples. The results showed that the RhoVol method was more rapid, safe, and precise, but tended to consistently underestimate the density of the coal sample, probably due to varying coal porosity.

Oct 3, 2023