Search Documents

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Edward Martinez

The reactions occurring in the copper segregation process were studied by heating mixtures of chryso-colla, salt, and a reducing agent. The techniques used in this investigation were differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). The initial chloridizing of the oxide copper occurs below 500°C and cupric chloride may be the compound formed. Volatilization and reduction of the copper chloride take place above 550°C, although these reactions do occur to some extent below 550°C. A difference in the distribution of the metallic copper in the reducing agent was found when sodium chloride was used compared to magnesium or calcium chloride. Segregation was obtained with mixtures of cupric oxide, salt, and charcoal with no quartz or silicate present. Preliminary tests indicate that segregation may occur even in the absence of water vapor. The DTA and TGA techniques were found to be of great value in studying these reactions. The copper segregation process is a method for treating oxide copper ores. The ore is heated, most commonly in a kiln, with a reducing agent and a halide salt, generally sodium chloride, to approximately 700°-750°C and held for 30 to 60 min. The addition of the salt results in the migration and reduction of the oxide copper to metallic copper on the surface of the reducing agent rather than in the original mineral structure. The metallic copper can then be recovered by a subsequent leaching or flotation step.1-4 Experimental work in 1923 on oxide copper ores from the Sagasca mines in Chile led to the discovery of the reduction process. It was found that during the reduction of the copper mineral with coal, at about 700°C, the copper migrated to the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge. The ratio of salt to reducing agent may vary somewhat, but in general 0.5% to 1.5% sodium chloride and 0.5% to 1.0% coal or coke have been mixed with the ore. Less than stoichiometric amounts of salt are required to convert all the oxide copper to a chloride, so that a cycle of reactions appears to be occurring. Several investigations reported in the literature have proposed reactions to explain the mechanism of the process.5-10 There appears to be general agreement that water is necessary for the reactions to occur; that once the sodium chloride reacts with silica or silicates in the ore, the hydrochloric acid formed will convert the cupric oxide in the mineral structure to cuprous chloride. However, there appears to be a conflict of opinion on the reactions involved in the reduction of the cuprous chloride to metallic copper on the surface of the carbon. Rey has indicated that salt, water vapor, and

Jan 1, 1968

By E. Michelotti, M. Cardu

This paper presents the results of a new method that has been tested to recover metallic cobalt lost by diamond beads from rock cuttings. When dimension stones are cut using diamond wire saws, the beads become worn and, before the end of their cycle life, lose a certain amount of material; this material is prevalently made up of sintered metal and diamonds. The material is then washed away, together with rock debris, in a dilute pulp. In effect, this process involves the dispersion of economically valuable, but potentially polluting, materials (such as cobalt) that are used to confer indispensable technological features to the beads. This current research aims to develop a waste-processing pilot plant (High-gradient Magnetic Separator or HGMS) to recover metallic components from the pulp by means of a suitable separation. The research\u2019s purposes are two-fold: a. to remove the polluting components from the rock debris before their disposal and b. to start a recycling process of the valuable metals.

Jan 1, 2010

By Shu-cai Zhou

"To understand the solidification behavior of austenitic heat-resistant stainless steel (TP34 7) in rotary electromagnetic-field, the influence of electromagnetic stirring in mold (M-EMS) on solidification structure of TP34 7 heat resistant steel in a round billet continuous casting was investigated based on industrial experiments. The results indicate that the excellent billet solidification structure of TP34 7 heat resistant steel can be obtained with appropriate electromagnetic stirring parameters. The solidification structure of TP34 7 heat resistant steel can be remarkably refmed, central porosity and shrinkage cavity can be remarkably decreased and equiaxed grains zone widens was enlarged. The industrial trials verify that the stirring intensity of TP34 7 heat resistant austenitic stainless steel should be higher comparing with plain carbon steel. Due to a higher viscosity, rotating speed of molten stainless steel was 20-30% lower than that of molten carbon steel in the same magnetic flux density.IntroductionIn recent years, the development of ultra super critical (USC) plants is accelerated by the demands of environment protection and energy saving, and USC plants with steam temperature and pressure conditions in excess of 593°C and 24.lMPa respectively were constructed. To achieve the goal, it is important to develop new materials with excellent high temperature strength, superior resistance to oxidation and corrosion at high temperature. Besides, their cost must be low enough to meet the requirement of plants [ 1]. TP34 7H steel is promising austenitic heat-resistant steel, which is used as superheater/reheater tube material and is extensively used for high temperature components and fossil-fired power plants, and suitable to be used in USC boilers plant. This kind steel contains with about 0. 7%Nb and it keeps higher allowable stress and creep rupture strength than TP304 and TP321H [1-2]. TP347H has conventionally been produced by ingot casting followed by forging and rolling. Recently, in order to decrease the production cost, challenging trials to produce these types of alloys by a continuous casting (CC) process have been attempted. However, the solidification structure of austenitic stainless steel is one of the key issues that attract more attention. Due to the low thermal conductivity of TP347H heat resistant stainless steel (much smaller than that of plain carbon steel), pronounced defects during continuous casting of austenitic heat-resistant steel such as coarse columnar, center porosity and coarse bridging, greatly influence mechanical properties of fmished products.A widely used technique in metallurgy is the inductive drive of molten metals using rotational or traveling magnetic fields. Recently, rotary electromagnetic stirring (EMS) has been applied to reducing various defects and improving increase the solidification structure of the metals in the continuous casting of steel, Al-based alloys and Mg-based alloys [3-8]. Electromagnetic stirring of plain carbon and low alloy steel in the continuous casting bloom and slab is well established for improving the quality of cast products [9-11] and is widely used in industry. However, very few literatures on electromagnetic casting of heat resistant stainless steel have reported. In this work, an industrial plant trial was performed to clarify the effect ofM-EMS on the macroscopic quality ofTP347heat resistant steel billet, in which the regularity and mechanism of the influence of EMS on solidification casting billet were discussed."

Jan 1, 2014

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By Kurt M. Larson

Future haulage cost projections led Foster Yeoman Limited into developing a fully mobile crushing and conveying system at its Torr Works quarry in Somerset, England. The purpose-built system has an effective throughput of 2,500 tonnes/hour and features an Orenstein and Koppel (O & K) manufactured walking frame, a Fuller-Traylor type 54 X 74 TC gyratory crusher, and unique mobile conveyor modules designed and manufactured by Foster Yeoman. Used in a single-bench operation in this 6 million-tonne per annum limestone aggregate quarry, the system is fed at the production face by 2 Caterpillar 992C loading shovels. The entire system is moved on a daily basis following production face locations.

Jan 1, 1986

By T. H. Etsell, P. Kerr

Over the past 50 years, there have been a number of geological, mineralogical and metallurgical studies carried out on the Clear Hills ironstone deposits in northern Alberta, Canada. Due to the low grade and complex mineralogy, previous metallurgical studies have achieved limited success. After rejecting some of the more ‘conventional’ techniques for iron ore beneficiation, the authors chose to investigate the grain enlargement/iron segregation process for the beneficiation of the Clear Hills ironstone. The segregation reactions for iron have not been explored in as much detail as they have for copper and nickel. Iron segregation roasting involves the addition of a carbonaceous reductant and a chloride transport agent to an iron oxide ore, and heating the mixture to an appropriate temperature. The benefit of this process is that it allows ores in which the value minerals are intimately associated with gangue minerals to be processed in circumstances where conventional iron ore processing techniques are not suitable or capable of upgrading the material. As iron is one of the few elements that can be transported through this process, a clean high purity metallic concentrate can be achieved.Through the use of crucible testing followed by Davis tube magnetic separation, scanning electron microscopy, X-ray diffraction and atomic absorption spectroscopy analysis, characterization of the reaction products has been made with an improved understanding of the reaction mechanism.

Jan 1, 2015

By Strickland R. E J

Heap leaching is establishing itself as an efficient method for the extraction of gold from low grade ore. It has the advantage of low capital costs, low operating costs and rapid startup. However, not all ores are amenable to heap leaching. It is only applicable to well oxidized ores that have reasonable permeability characteristics. Ore with excess fines or clay often display low permeability and are unsuitable for heap leaching.In this study, an attempt has been made to increase the rate of cyanide leach solution percolation by flocculating clay particles or reducing the surface tension of the leach solution. A wetting agent was found to decrease the rate of gold dissolution, possibly by presenting a hydrophobic surface to the gold particle. Flocculation of the clay increased the solution flow rate. The flocculation agent had no affect on the total gold leached but decreased the leaching rate.

Jan 1, 1992

By V. M. Lsoitko

Statistical methods of technological mineralogy are used to model processing flowsheets in order to improve ore dressing efficiencies. The procedure involves determining geological and mineralogical characteristics of ores, classifying ore types and metallurgical procedures, and developing computer programs to interpret essential mineralogical parameters from on-stream analysis data. The on-stream analysis data include magnetism, radioactivity, luminescence and assays. The data are interpreted by computer and appropriate adjustments are made automatically in the plant.

Jan 1, 1989

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By J. E. Nesset

Significant progress has been made over the past few years on characterizing and understanding the hydrodynamic properties of frothers and collectors and their effect on flotation performance. This new understanding of the relationship between chemistry and hydrodynamics has dramatic implications for how flotation circuits should be controlled and optimized. Previous work has shown that choosing a frother of the right 'strength' is critical to the optimization process, and the work and discussion presented here serve to strengthen the argument. In addition, we know that collector chemistry may also influence hydrodynamic properties and needs to be taken into consideration. To achieve the desired outcome, the overall system of reagents and operating parameters must be considered. This paper describes and discusses some of the findings from recent research on frother and collector chemistry effects (on hydrodynamics), and how this knowledge can be used to improve flotation performance. Examples from plant experience are discussed.

Jan 1, 2009

By D. D. Howat

In the field of high temperature smelting processes there have been two dramatic changes in the past twenty years. These are, first, the application of tonnage oxygen for direct injection for the refining of molten iron and other metals and to provide the means of enriching air used for the combustion of fuel. Second, the application of electric power for the generation of high temperatures in place of the combustion of fossil fuels. Of these two developments the application of tonnage oxygen for the refining of molten iron has virtually revolutionised the steel industry throughout the world. The magnitude of this development is exemplified by the fact that less than 5 per cent of the world's steel production in 1960 was made by this process or 16 million tons out of a total of 350 million tons of steel produced, while in 1970 over 40 per cent of the world steel production was made by this process, ie, 251 million tons out of 628 million tons total. In the same period the proportion of steel produced by the old-established open-hearth process has shrunk from 75 per cent to 38 per cent. In the whole history of the development of high temperature metallurgical smelting processes there has never been anything remotely approaching this. The other development, the application of electric power for the generation of high temperatures has not had the impact of the oxygen injection process but I believe that what we should call the electric smelting revolution in metallurgical processes has very far-reaching ramifications for steel production and other pyrometallurgical processes. This may seem a bold and brash statement but it must be remembered that the oxygen injection process constitutes a link in the chain critically dependent upon the production of vast tonnages of molten iron from very large modern blast furnaces. The Achilles heel of this chain of processes, upon which such a large percentage of the world's supply of steel depends, is the availability of metallurgical coke in turn dependent on natural resources of coking coal. Without any exception each industrial country in the world faces a shortage of resources of coking coal and in some cases a critical shortage. Certainly within the present century the major iron and steel producing countries of the world will face this critical shortage of coking coal and major modifications to steel making processes will become inevitable. W. F. Cartwright (Deputy Chairman of B.S.C) said recently that there are considerable doubts as to whether the world will be able to provide enough coking coal to meet world steel demands from the late 1970's onwards if the B.F.remains the main means for making iron from ore. This is one of the supreme ironies of the world metallurgical situation to-day when the technology of iron and steel production has reached an extremely high peak of technical efficiency. The newest modern iron blast furnace capable of producing 6 000 to 8 000 tons per day of molten iron represents probably the most efficient piece of high temperature metallurgical plant and operation known to man. The conversion of this molten iron into steel by the oxygen injection process has made available to the engineering industry steel of a quality and at a price which is quite remarkable. Yet this vast metallurgical pyramid rests on the completely insecure and uncertain foundation of inadequate world resources of coking coal. The shortage of reserves of coking coal in this country is acute and it is possible that these resources will be exhausted within the next twenty years. Yet unless some completely unexpected catastrophe occurs the demand for steel in this country will probably rise at a faster rate than in the Western world due to the expansion of the Bantu population and the increased standard of living. To offset the inevitable shortage of coking coal are our much greater resources of bituminous coal which although of low grade provide a suitable fuel for electric power generation. The geographical disposition of the coal fields in relation to the great industrial areas of the Transvaal makes it inevitable that the development of the pyrometallurgical industries must depend heavily on electric power. The position in this country with regard to electrical power generation and consumption is rather anomalous. Per capita consumption of electric power is high - in 1964 almost twice the world average of 870 KWH and twenty-five times the average of 34 KWH for the Continent of Africa. In 1964 fifty-four per cent of the total world electric power was used in industry - the ratio being approximately 1/9 mining to manufacturing uses. As shown in Table I in 1969 67.2 per cent of the total output of electric power from ESCOM was used for mining and other industrial uses but almost in the ratio 6/4 mining to industrial uses. These figures emphasise the enormous importance of the mining industry to the economy of this country and underline the major contribution made by the gold mining industry. What is of very significant importance is that although the mining industry remains by far the largest single consumer of electrical power the consumption of power for industrial uses is rising rapidly as shown in Table II.

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By R. S. Kalyoncu

Materials demands by the advancing process technologies, desire for higher performance and durability, and improved efficiency in combustion processes, such as applications in heat engines, heat exchanges, and batteries have added to the driving force fueling R&D efforts for the development of components with the combined characteristics of metals and non-metals. These new materials involve refined and specialized microstructures that can lead to improvements in the performance characteristics and durability new technological applications require. Fabrication and sintering methods, once believed to be sufficient, alone, have been found to be inadequate in the manufacture of such advanced components. Realization of the importance of the starting powders has led to efforts to produce materials of ultrahigh purity and ultrafine particle size with very narrow particle size distributions. Such powder characteristics are essential for the fabrication of components with high density and with the desired mechanical, electrical, or magnetic properties called for by the specific application. Novel ultrafine and ultrapure powder preparation techniques are discussed and effects of impurities on the powder characteristics, particle size and morphology, sintering behavior and properties of the finished product are elucidated.

Jan 1, 1992

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By Ing. R. Geutskens

Zinc-bearing dust from blast furnace gas-scrubbing operation is a well known environmental health problem in the iron and steel industry. Hoogovens IJmuiden (The Netherlands) developed processes to solve this problem. 90% of the zinc is concentrated in 25% of the dust (the fine particle fraction) by means of slurry-hydrocyclonage. The resulting fine particle fraction is treated in a pressure leaching process. Hydrochloric waste pickle liquors have been used as a leaching liquor. By creating optimal leaching conditions more than 98% of the zinc is brought into an acid' solution, whereas nearly all the iron remains in the residue. The zinc can be separated selectively from the solution. The residue can be reused in the blast furnace (via the sintering plant). In the article information is given about the research work and -results of the pressure leaching process as well as the possibilities of the process for solving comparible problems.

Jan 1, 1990

By Charles Luner

ALTHOUGH the kinetics of the atmospheric oxidation of tin have been studied,1-3 the kinetics in pure oxygen have not been reported. This note presents some results of the kinetics of the oxidation of tin foil in pure oxygen. The tin foil used in this investigation was 99.78 pct pure, the two major impurities being Pb (0.17 pct) and Sb (0.024 pct). The foil was degreased and air-dried prior to oxidation. The air-formed film was estimated by coulometric reduction4 of the surface oxides to be about 25A. The samples, which were in strip form and had a total geometric surface area of about 300 sq cm, were first evacuated at room temperature in an oxidation bulb to 1 X 10 -5 mm Hg and subsequently degassed for 1 hr at the temperature of the experiment. Spectroscopically pure oxygen was then introduced into the bulb. The rates of oxidation were measured by following the rate of pressure change due to oxygen consumption in a closed system, the volume of which was sufficiently large so that the pressure change during an experiment was 10 to 15 per cent of the total pressure. An oil-mercury manometer,5 with a sensitivity of 3 X x mm Hg (which corresponds approximately to 5 X 10 -7 gm of oxygen) was used to measure the pressure change. The oxidation bulb was heated by an oil-bath and controlled to within -10.3 C. The reproducibility of the rates was good, as determined by the coincidence of rates at 190oC for duplicate experiments. Fig. 1 shows the oxidation curves in the temperature range 168 to 211.5oC at 8 mm Hg pressure. The effect of pressure on the rate of oxidation at 190°C is also shown. The rate of oxidation was not markedly affected by changes in pressure in the range 4 to 9 mm Hg, except perhaps at the lowest pressure, 4 mm Hg, where after about 70 min there appeared to be a decline in the rate, as compared with the rate at the higher pressures. At the lower tem- perature, 168oC, and for short reaction times, it is difficult to distinguish between a linear relationship and a slight curvature in the oxidation rate. However, for longer times, there was a somewhat larger indication of curvature. The samples after oxidation were gold-colored in appearance. The oxide that was formed at 170°C was identified as a-SnO by reflection electron diffraction. This is in agreement with results obtained by other workers.6, 7 The rate data best fitted the logarithmic-oxidation rate law, w = K1n ln(1 + -t/to) [1] where w is the weight of oxygen consumed, t is the time, and K In, and to are constants. First estimates to were obtained according to the method of Taylor Thon8 and were then employed to obtain the best simuItaneous estimates of to and K In, that would fit the logarithmic expression. These estimates were found numerically, so that the residual variance could be minimized. The calculations were performed on an

Jan 1, 1961