Search Documents

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By L. Diaz, J. Serp, L. Massot, P. Chamelot, M. Gibilaro

The discovery of NdFeB permanent magnets helps to perform technologies with reduced weight and gives them access to miniaturization. The industrial process of production of the Nd-Fe alloy by electrolysis used to manufacture NdFeB magnets consists in reducing Nd3+ ions dissolved in molten fluoride salts. The electrochemical behavior of neodymium is studied in LiCl-KCl and LiCl molten salt systems, examining reduction mechanisms, potential deposition, and faradaic yields.

Mar 1, 2017

By M Camarda, A Pirson, F Vasconcelos, J Mesquita

ArcelorMittal Prijedor is a goethitic iron ore mine located in the north-west of Bosnia and Herzegovina, which mainly supplies ArcelorMittal’s European subsidiaries. Annual production of the asset stands at the level of 1.5–2.1 million tons of iron ore product which is sent to ArcelorMittal Zenica steelmaking plant. Two types of products with approximately 50 per cent Fe are generated in Prijedor through a process composed by crushing, screening, and magnetic separation stages. Within this process one of the tailings produced is called ‘ultrafines’. The ‘ultrafines’ product corresponds to the desliming hydrocyclones overflow in Prijedor plant, which is classified in a size fraction below 25 μm and corresponds to about 5 per cent of feed. This material is richer in iron than the coarser size fractions of the ore but do not present a good performance in concentration processes. In this way, several studies have been carried out during the last years to find solutions to use the ‘ultrafines’ material without success. In this context, the possibility of dehydroxylate the goethite contained in the material transforming the mineral into hematite and thus increasing the iron grade of the final product was investigated. During the research, several dehydroxylation tests with different temperatures and time of exposure were performed. Using dihydroxylation process at temperatures higher than 800°C it was possible to produce a material with 43 per cent Fe from the original 39 per cent Fe ‘ultrafines’ sample. In addition, the dehydroxylation tests confirmed that goethite becomes completely transformed into hematite at 400°C (with an exposure time of 60 mins) and material is completely sintered at 1200°C. A simulation study based on dehydroxylation tests results showed that it would be possible to use a ‘ultrafines’ product with Fe grade higher than 45 per cent to produce a material with 50 per cent Fe through a complete dehydroxylation process.

Sep 18, 2023

By Côme Carbonneau

The ten -year case history of La Société Québécoise d'Exploration Minière (SOQUEM) is reviewed under the headings of the company's raison d'être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By Satu Strömberg

Four different nickel concentrates were oxidized in a laboratory scale laminar flow furnace in simulated flash smelting conditions. The major nickel- and iron-bearing minerals in the con- centrates were pentlandite, violarite, gersdorffite, and pyrite and pyrrhotite, respectively. Thermal decomposition, ignition and oxidation behavior of nickel and iron sulfides were examined by using optical and scanning electron microscopy. General reactivity of the concentrates was monitored with sulfur removal which was most effective in violarite-based concentrate. Pentlandite-concentrates needed higher experimental temperatures for complete desulfurization and gersdorffite-based concentrate contained 5 - 10 % of the original sulfur even in the most oxidizing conditions studied (1 100°C, 50 vol-% 02). The reactivity of the iron minerals was found to depend on the other minerals present in the concentrate. In this paper, the observed re- action products and mineralogical changes are presented and preliminary conclusions of possible reaction mechanisms of nickel-bearing minerals are discussed.

Jan 1, 1997

By George P. Demopoulos, Yan Zeng, Zhibao Li

Precipitated silica is marketed with a rising demand as reinforcing filler in the rubber industry and as a potential raw material for the synthesis of lithium-ion battery electrodes. Due to an awareness of the environmental impact of the existing processes for the production of precipitated silica, a green and sustainable process was proposed by using sodium bicarbonate (NaHCO3) as an alternative to sulfuric or hydrochloric acid in the precipitation reaction with sodium silicates. The use of NaHCO3 allows for better control of the supersaturation and pH to form silica with desired quality. Additionally, Na2CO3 solution as the process by-product is recyclable because it could be recovered to produce NaHCO3 by absorbing CO2. The solubility of sodium metasilicate nonahydrate (Na2SiO3·9H2O) in the Na-CO3-HCO3-OH-H2O system was measured using a dynamic method in the temperature range from 288.15 to 308.15 K. It is found that the solubility of Na2SiO3·9H2O decreases with increasing concentration of either Na2CO3 or NaOH over the investigated concentration range. With the aid of the OLI platform, a chemical model for the Na2SiO3-Na-CO3-HCO3-OH system was established with newly obtained interaction parameters of the Bromley-Zemaitis model by regression of experimental solubility data. The new model predicted the solubility of Na2SiO3·9H2O in multi-component systems with good agreement and was used to conduct a preliminary feasibility study of the new process.

Jan 1, 2015

By L. J. Barnes, R. O. Koch, J. H. Versteegh, P. J. H. Scheeren, F. J. Janssen

Following two years of laboratory research with bench scale reactors, a 9 m3 experimental process demonstration reactor was installed at Budelco's zinc refinery to treat their underlying groundwater. A 600-fold scale-up was successfully achieved. It has demonstrated that this anaerobic microbial process can remove a wide range of heavy metals and sulphate to the required levels. Extended operation of the demonstration unit has shown that the process is robust, can withstand wide variations in feed composition, rapidly recovers from operational upsets and is easy to start up and shut down. The metal sludge produced can be processed in a metal refinery to recover both metals and sulphur.

Jan 12, 1992

Thomas Haight Leggett, London, Eng. (communication to the Secretary): Mr. Hammond has given us a concise yet complete description of the Witwatersrand gold-fields, and the character of the operations which have resulted in their remarkable development.

Jan 1, 1902

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow, S. T. Bagley

"Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol.The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment.The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location.In three of the mines filter samples were collected for DEA-associated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, CO2. NO, NO2, and SO2, were well below regulated levels.INTRODUCTIONDiesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992)."

Nov 1, 1995

By K. A. Pauly

(Wilkes-Barre Meeting, June, 1911.) COMPRESSED air has been and is still very extensively used in connection with mining-operations, but its application in the past has been almost entirely confined to supplying power to underground machinery. Its introduction was due to the difficulty of taking care of the steam which is exhausted underground, rather than to any advantage in efficiency to be gained by its use. The ease with which electric power may be carried to the remotest parts of the mine and the high efficiency of the electric motor have long been appreciated by mine-operators, and electric power is now extensively used underground in the more recent developments, while many of the compressed-air engines in the older workings are being rapidly replaced by electric motors. Recently, however, it has been suggested to use compressed air for driving the large shaft-hoists, the air for the engines being supplied by electrically-driven compressors, and an installation of this character is being erected at Butte; Mont. It is the object of this paper to compare the compressed-air system of hoisting with the various electrical systems, from the stand-points of first-cost and cost of operation. However, before entering into a discussion of the various systems, it will be well to consider briefly the conditions affecting the choice of a system of hoisting in which electricity is the ultimate source of power. The power required by a mine-hoist is extremely intermittent and fluctuates between very wide limits, the all-day average consumption of power not exceeding from 5 to 15 per cent. of the maximum demand during hoisting. The cost of supplying power for such a fluctuating load is necessarily higher than that for supplying an equal amount of

Dec 1, 1911

By Katsutoshi Saibara

Network communication note is a cloud system for an earthwork project. It enables backhoe operators and dump truck drivers to monitor their own works in progress currently and performed up to the present, and to have opportunity to reflect on their own bearings in the earthwork operations, and then could increase their situational awareness to the actual work conditions. First, this paper presents problems and purpose. Secondly, the configuration of the network communication note is reported. Thirdly, examples of communications enhanced by the network communication note are shown. Finally, remarks are described.

Aug 1, 2013

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits ofthis approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the S02 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia, limonitic ore from New Caledonia and garnieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potential followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Å Sandström

Loussavaara-KiirunavaaraAB?s (LKAB) iron ore mine, Kiirunavaara, is of magnetite type and associated with apatite, a calcium phosphate mineral. Rare earth elements (REE) have been found in connection with the apatite but also in other minerals. An apatite concentrate was produced by flotation, in order to investigate the possibilities to extract REE from the apatite by hydrometallurgical means. The content of rare earth elements calculated as oxides (REO) was 0.44% in the concentrate. Initially, leaching was done with large excess of sulfuric acid, hydrochloric acid, and nitric acid to study the REE solubility with different acids. In sulfuric acid, the leaching recoveries of the different REE varied between 35% and 69%. The reasons for the relative low recoveries, were that the rare earth elements precipitated together with huge amounts of gypsum, that was formed during leaching. However, both hydrochloric- and nitric acid gave almost complete extraction of the REE into solution. Analysis of the small leaching residue obtained, revealed, that mainly the light REE remained in the residue indicating that a small part of the light REE were present in the concentrate, in some acid, insoluble mineral other than apatite. With the aim to separate the REE from the phosphoric acid, the solutions from hydrochloric- and nitric acid leaching were neutralized to a pH of approximately 2 with ammonia. During neutralization, REE were precipitated as phosphates with good recoveries and a concentrate of 10.5% REO suitable for further upgrading was obtained, while the remaining solution can be used for fertilizer production. In further solvent extraction studies, it was shown, that after re-dissolution the REE could be effectively extracted by Cyanex 923, thus allowing for purification from calcium and phosphate ions. The REE were finally stripped from the organic phase and a REE nitrate solution was produced. Keywords: apatite, rare earth elements, REE, leaching, solvent extraction, cyanex 923

Sep 1, 2012