Search Documents

By W. H. Smith

IN the course of an investigation on chromium containing minor amounts of alloying elements, the information herein has been obtained on the crys-tallographic orientations resulting from arc melting, rolling, and annealing. The chromium used in this investigation was electrolytic flake obtained from the Electro Metallurgical Co. This material was heated for 20 hr at 1600°C in hydrogen with a dew point of about — 100°C. The oxygen and nitrogen content of the chromium after this treatment was 0.0003 pct 0 and 0.005 pct N. Five pounds of this chromium were arc melted in a water-cooled copper crucible. After arc melting, the oxygen and nitrogen contents were 0.002 and 0.025 pet, respectively. A section of this ingot is shown in Fig. 1. By means of a back-reflection Laue technique, the crystal habit of the cast ingot was determined. As expected, it was found that the [loo] was approximately the axis of the columnar grains. In this respect, chromium behaves like other body-centered-cubic metals in that a cubic axis is normal to the cold surface of the mold. A slab cut from this ingot was rolled at 600°C as follows: four 30 pct reductions were made with intermediate anneals at 1200°C for 15 min. Rolling was done with the [loo] of the columnar grains in the rolling direction. Following the final anneal, an 80 pct reduction was taken at 600 °C. The final sheet thickness was ten mils. By polishing and etching, the thickness was reduced to four mils and the grain orientation determined by the transmission Laue method using molybdenum radiation with a zirconium filter. Fig. 2 is the (110) pole figure for this material with the ideal (100) [011] and (111) [112] orientations indicated. The orientation is typical of most cold rolled body-centered-cubic metals having the [llO] of the grains approximately in the rolling direction and the (100) planes approximately in the plane of the rolled sheet. There is also evidence of some 10) [1 orientation. The grain orientation of sheet rolled 40 and 80 pct in the same direction as before at 600°C followed by recrystallization at 12000 C for 15 min was determined by a back-reflection Laue technique. A random texture was found in both cases. This 1200°C 15 min anneal was found to give complete recrystallization and some grain growth.

Jan 1, 1956

By William S. Eaton

Managing a mine or mineral processing operation in today's environment presents many unique challenges to mining companies. In recent years, headlines around the world have publicized major incidents such as those associated with the Marcopper Mine in the Philippines, the cyanide release in Guyana from the Omai gold mine and numerous other mishaps associated with mining. These notable upsets were due to engineered system failures, either during normal operations or as a result of uncontrollable events. There fore, many mining firms are attempting to assess their overall risks and establish some priority for expenditure of limited operational and environmental budgets. Failure of an engineered component can have dire operational consequences that affect profitability until repair or replacement can be completed. In addition, there may be significant environmental consequences associated with the engineered system failure. This, too, may affect profitability for an extended time or even the viability of an operation. An engineered risk assessment (ERA) can support a mining company's efforts to cost effectively manage environmental risks associated with the operation of its facilities. The ERA approach also provides information about the current condition of engineered systems. This ERA approach provides a systematic review of the risks of an engineered system failure and the possible associated environmental consequences at mining company facilities. This approach has been successfully applied to many industries and types of engineered systems (Barneich et al, 1996; Whitman, 1984; Power and Tomkins, 1974; Keeney, Nair, and Kulkarni, 1979). This approach evaluates all mining and mineral processing facilities located at a single site and compares them with similar facilities located at multiple mine sites. The ERA approach has been applied to a mining, milling, smelting, leaching and refining operations. These assessments can be part of a comprehensive environmental program to aid in the recognition and cost effective management of the potential environmental risks associated with the operation of facilities. ERA results support plan-

Jan 1, 1997

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By Christopher Boys

"Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized. These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. In this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dissolving huge cavities in the evaporites. The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds. In at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation.Geological indicators of the proximity of an anomaly may include: a change in insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore wne, and drops in topography > 10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies. Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By Jong-Ren Tarng, Gin-Hwa Chen, Wen-ku Chang, Ke-Ming Lin, Yuan-Haun Lee

"The majority of early studies used X-ray diffraction, but this requires a model to interpret the diffraction processes. A turbostratic model has been applied by Warren, Franklin and Bacon to a wide range of materials including both soft and hard carbons. Maire and Mering applied the same methods to the interpretation of the (001) lines of a series of graphitic carbons. In our case, graphitic carbons undergone high temperature and high pressure graphitization processes have been evaluated by the same methods. It were found that most technological XRD data were obtained by a Rietveld method with the least-squares refinements could be in the simplest way since the full correction technique is very laborious. The behavior of carbon materials as it proceeds through the graphitization process is characterized by changes in the measured interlayer spacings (d) a~ a function of temperature. A series of graphitic carbons including the transformation of diamond to graphite through the process under high temperature and high pressure have been evaluated. A simple calibration equation has been established. IntroductionRecently, in battery industry, carbon materials are used as cathode in lithium ion batteries. However, graphitization of those carbon materials is concerned as if lithium ion intercalated into those carbon cathode. Both high-graphitization and low-graphitization carbon materials are suitable for this kind of application.As for graphitization, the starling materials from which carbons may be prepared vary extensively from pure chemical compounds, to mixtures containing II wide range of molecular weights, such as pitches. So its graphitizing, perhaps the most notable feature of the process, is the very wide range of temperature over which the perfection increase, unlike the more common transformations of solid state materials which occur in a narrow temperature range. The variables involved in the conversion of the initial hydrocarbon to a carbon residue, which may vary widely in final perfection, are time, temperature, stress and impurity content"

Jan 1, 1996

By A. Motamedi

Indoor localization has gained importance as it has the potential to improve various processes related to the lifecycle management of facilities and to deliver personalized and location-based services. Radio Frequency Identification (RFID) based systems, on the other hand, have been widely used in different applications in construction and maintenance. This paper investigates the usage of RFID technology for indoor localization of RFID equipped movable assets during the operation phase of facilities. The location-related data on RFID tags attached to fixed assets are extracted from a Building Information Model (BIM) and can provide context-aware information inside the building which can improve Facilities Management (FM) processes. The paper proposes a new approach to use received signals from available reference tags in the building attached to fixed assets to locate movable assets. The approach uses signal pattern matching and clustering algorithms for localization. As a result, a user equipped with an RFID reader is able to estimate the location of target assets, without having access to any Real- Time Location System (RTLS) infrastructure. A case study is performed to demonstrate the feasibility of proposed methods.

Aug 1, 2013

By E Matinde, M. Mnisi, I. C. Thobadi, W. Clark, J. D. Steenkamp

Pyrometallurgical smelters utilise tap-holes, through which liquid metal, matte and/or slag are tapped at regular intervals. However, tap-hole failures can have a devastating impact on smelters, which includes loss of equipment, human life and business interruptions. Contributing factors to tap-hole failures include poor and/or incorrect refractory material selection, including tap-hole clays. The functions of tap-hole clays in smelters include their ability to be extruded and drilled with ease at the end and beginning of a tap, and their ability to resist chemical wear due to molten metal and slag during tapping. Mintek is currently developing methods of evaluating properties of tap-hole clays with a specific focus on workability, and wear mechanisms of clays due to ferrochrome alloy and slag. Of particular interest to this study was the characterisation of various tap-hole clays. This paper evaluates the chemical and phase chemical properties of three different tap-hole clays. The bulk chemical composition of the tap-hole clays was determined by inductively coupled plasma optical emission spectroscopy, proximate analyses and combustion methods. The bulk phase compositions and specific phase chemical compositions were studied using quantitative X-ray diffraction, scanning electron microscope and electron probe microanalyses techniques. Keywords: Tap-hole clay, chemical analyses, phase chemical analyses, ferrochrome

Jan 1, 2020

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By R. D. Brown

In view of the many changes which have taken place since 1950 in the rules of the Income Tax Act concerning the deduction of exploration and development expenses, many corporate taxpayers each year face the tedious task of determining which particular rules their unclaimed exploration and development expenses are subject to and in what sequence these expenses are to be claimed. Recent amendments to the Act have cleared up some of the mystery of the "ordering" of these deductions. This article examines the sequence in which various categories of exploration and development expenses are to be deducted in accordance with the terms of the Act as amended by Bill C-11.

Jan 1, 1978

By P J. Howard

Atlas Iron Limited’s McCamey’s North project lies at the eastern end of the Hamersley Basin, approximately 50 km east of Newman, Western Australia, and 3 km northeast of BHP Billiton’s Jimblebar Mine. The presence of significant surface iron mineralisation identified during field reconnaissance, has subsequently been further defined by detailed mapping and RC drilling.The project area is dominated by outcrops of moderate to steeply north and south dipping banded iron formation, cherts and shales of the Boolgeeda Iron Formation overlying rhyolites and rhyodacites of the Woongarra Volcanics. In lower lying areas recent colluvium and alluvium mask the Archaean geology. Drilling and downhole geophysics has allowed a composite stratigraphic section to be compiled through almost the entire Boolgeeda Iron Formation.Surface orientations and subsurface stratigraphic correlations using natural gamma logs indicate large scale open folding about east-west trending fold axes across the project area; while small scale tight to isoclinal folding with similar fold axis orientations are visible at the outcrop scale. These folds are cut by a number of moderate to steeply south-dipping normal faults defining a series of north-dipping fault blocks which repeat the stratigraphy across the project area.Bedded iron mineralisation consists mainly of haematite-martite and goethite ores with best results of 78 m @ 60.5 per cent Fe. Vitreous goethite is observed at the surface of the mineralised horizons. The mineralisation exhibits a strong stratigraphic control and extend down-dip up to 120 m below surface. The strike extent of the mineralisation is still to be determined. An inferred resource of 39 Mt at 58 per cent Fe has been defi ned to date (ASX: AGO 3 February 2011).The fi ndings at McCamey’s North indicate that there is potential for economic iron mineralisation to exist in other areas of Boolgeeda Iron Formation within the Hamersley Basin.

Jul 11, 2011

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By Gary R. Adams

Coating thickness control is typically difficult with touch-up solders for galvanized steel, and corrosion properties and abrasion resistance are sometimes poor. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with zinc-tin based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix The mouldability was dependent on the microstructure of the starting material, and optimum structures could be obtained through control of casting solidification rates and/or by the addition of small amounts of copper. Hardness and preliminary corrosion test results showed potentially good mechanical and corrosion behaviour. The absence of toxic materials ensures environmental friendliness. Comprehensive performance testing is continuing on selected experimental zinc-tin-copper touch-up solders.

Jan 1, 1992

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By Kun Li, Shuaishua Yue, Huigui Li, Yuan Ruifu, Yongxiang Xu, Huamin Li

"Coal seams in Tashan Mine of Datong Coal Group in China average 49.2 ft (15m) thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 12.5 ft (3.8m) and the top coal caving height was 36.7 ft (11.2m). The gateroad pillar between panels was 124.6 ft (38m). During retreat mining, serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore, pillarless mining was experimented.Using numerical modeling and comparative study of cases of similar mining condition, it was decided to employ a 19.7 ft (6m) wide pillar, rather than the previous 124.6 ft (38m) wide pillar. Support system for the gateroads was designed and implemented. During gateroad development, pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion.Since the development of gateroad has just completed, and retreat mining has not begun, the effectiveness of the proposed methods is unknown at this point. However, monitoring will continue until after mining. The results will be published in a separate paper.INTRODUCTIONGeneral descriptionTashan mine is located about 15 Km south of the city of Datong, Shanxi province, China (aure 1). The 2014 raw coal production was 25 million mt."

Jan 1, 2015

By K. Fagerlund

Methods for simulation of settler reactions, matte-slag separation and matte settling in copper flash smelting have been examined. The reaction, separation and settling phenomena of slightly oxidized chalcopyrite samples and cuprous sulfide-magnetite mixtures in fayalite type slags were examined at about 1300°C under inert atmosphere. Two methods based on introduction of molten samples of oxidized chalcopyrite concentrates or synthetic matte-magnetite mixtures onto the surface of molten iron silicate slag were tested. In the first method the samples were water quenched and polished specimens were studied and analysed using light optical microscope, scanning electron microscope, energy dispersive spectrometer. In the second method processes taking place after the introduction of samples onto the slag are followed "in situ" using X-ray transmission image monitoring. Great differences were observed in separation and settling behaviour of low and high grade copper mattes produced as a results of interaction of initial samples and slag.

Jan 1, 1997

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By J. J. Cai

The status of fossil fuel and secondary resource in metallurgy industry in China were reviewed, and conversion efficiency of fossil fuel, utilization technologies of secondary energy were studied. Fossil fuel, accounting for over 90% of energy structure in metallurgy industry, took in the highest flight in China, and a great deal of which was converted to secondary energy through the equipment of blast furnace and coke oven. These secondary energy which were mostly made of blast furnace gas(BFG), coke oven gas(COG) and Lindz Donawitz gas(LDG) occupied about 30% of total secondary energy. The way enhancing fossil fuel conversion efficiency, secondary resource recovery and the secondary energy such as BFG, COG, LDG utilization promoted to save fossil fuel was discussed in this paper. And efficient use of lower caloric value fuel was studied, such as preheating combustion air and fuel, generating electricity power etc. and regeneration purposes of high-caloric fuel was also researched, for producing hydrogen, methanol or direct reduction iron etc. The using model of secondary energy at iron and steel works was presented as fuel and chemical materials. The results suggest that utilization of these energy efficiently and reasonably could help to energy saving and environment protecting.

Jan 1, 2014

By L. A. Pursell

The case history, which is the subject of this paper, involves the expansion of a lime plant in Texas. The major new production unit is to be a 545.45 tonne per day coal fired rotary kiln. Auxiliary facilities include additional quarry haulage equipment, modifications to the crushing plant, a hydrator, storage facilities, and a loading system. The existing plant consists of a high calcium limestone quarry, two coal fired rotary and 10 gas fired shaft kilns, nth crushing, screening, stockpiling, hydrating, storing and loading facilities. The proposed modification would increase quarry volume from 545,000 tonnes per year to 805,000 tonnes per year. The plan also includes the addition of dolomitic lime to the product line which requires the purchase and handling of 186,000 tonnes of screened, washed dolomite yearly. A decision to undertake such an expansion was previously a simple and straight forward process. Such a decision now faces a major and complicating obstacle which can delay the project, raise the expected cost, or prevent it entirely.

Jan 1, 1980