Search Documents

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Huayi Yin, Wang. Dihua, Wei Xiao, Xuhui Mao, Diyong Tang

"The world production of crude steel reached 1.55 billion tons in 2012,which generated ~2.5 billion tons of CO2. Electrochemical metallurgy especially through high temperature molten salt electrolysis with renewable electricity stands for a great opportunity for producing “green” metals. In recent years, electrolytic production of iron without emission of CO2 in different molten salt systems has been reported. A cost-affordable inert anode is the key to produce acceptable eco-friendly iron by the novel molten salt electrolysis processes. Based on the authors’ research, this paper will discuss iron production by molten salt electrolysis using a nickel alloy inert anode. On the other hand, the paper also covers a novel molten salt CO2 capture and electrochemical transformation (MSCC-ET) process, in which CO2 is effectively converted to value-added carbon and oxygen in a molten bath using a cost-affordable nonconsumable SnO2 anode.1. IntroductionEnergy and materials are cornerstones to support the development of human society. The traditional primary metal production, especially iron and steel, and electricity production are mainly based on the reactions between carbon (coal) and oxygen (represented by equations (1) and (2) respectively), which produce huge amount of CO2.MxOy + 0.5y C = x M + 0.5y CO2 (g) + Q1 ( 1 )C + O2 (g) = CO2 (g) + Q2 ( 2 )In 2012, the world production of crude steel reached 1.55 billion tons, of which 46.3 %, ~0.7165 billion tons were produced in China. Based on the average level of 1.7t CO2 emission per ton steel, more than 1 billion tons of CO2 generated from steel industry in China in the year. Besides the iron and steel industry, thermal power plant leads the CO2 emission in both USA and China. The total consumed electricity in China increased to 4959 billion kWh in 2012, ~70% of it was from coal fired power plant. The average CO2 emission for electricity production in the typical thermal power plant in China is around 0.78 kg kWh-1. It accounts for ~ 3.868 billion tons of CO2 emission from thermal power plant in 2012 in China."

Jan 1, 2014

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

By Patrick Mclaren, Peter B. Hale

Canada, with one of the largest continental shelf areas in the world, has done little to evaluate its offshore unconsolidated mineral resources which include heavy minerals (gold, chromite, rutile etc.) and industrial minerals (silica sand and aggregates). During glaciation much of the continental shelf was covered with an ice sheet and later subaerially exposed with the result that glacial, glaciomarine and fluvial processes deposited sediments that may contain heavy minerals derived from onland locations. With rising sea-levels, beach and nearshore processes may have served to concentrate heavy minerals by winnowing and removing the lighter mineral components. These potentially valuable resources can be found with suitable exploration techniques such as seismic profiling and bottom sampling. Gold deposits are known to exist off the coast of Nova Scotia, and on the basis of form er beach mining, gold deposits probably occur off Vancouver Island and the Queen Charlotte Islands. Large deposits of silica sand occur near the Madeleine Islands and it appears likely that supplies of marine aggregates are present close to urban markets or sites of future mega-projects such as oil field developments. This paper, which is based upon a review of literature and consultation with members of the Department of Energy, Mines and Resources&apos; Coordinating Committee on Ocean Mining (DCOM), is the first step in assessing the Canadian offshore f or its resource potential with respect to quantified deposits, known and speculative mineral occurrences. Although this is a subjective evaluation, the potential appears promising. A more detailed resource inventory is required to provide a more certain assessment.

Jan 1, 1984

By D. Swanson

Cold Detonation Physics (CDP) is a patented new field of explosives and the name for the explosive that is produced when non-toxic dry ice (frozen carbon dioxide) is combined with powdered metals such as magnesium and aluminum, which are non-toxic and nitrogen-free. The explosive is detonator-sensitive and detonates according to the rapid reduction of carbon dioxide back to carbon, which produces solids comprised mainly of metal oxides and about 5% carbon. CDP was determined to produce a maximum of 300 liters of carbon dioxide per kilogram (4.81 ft3 /lb) and about 1.5 liters of carbon monoxide per kilogram (0.024 ft3 /lb). Both these figures shift according to metal content where higher metal produces less gases. According to theoretical modelling, the relationship between static pressure and metal content was determined to be an inverse parabolic curve with optimum pressure at 25% to 31% metal, depending on the type/s of metal/s used. Velocity of Detonation (VOD) was determined by measuring light at the wavefront with fiber-optic cable inserted into a series of holes drilled into the side of a 3-inch diameter (76 mm) schedule 40 steel pipe containing the mixture. The highest VOD was observed at 25% magnesium and measured between 2,500 to 4,500 m/s (8202 to 14,764 ft/s) when initiated by a 454-gram (1-pound) booster and an electric detonator. A 25% 50:50 alloy of magnesium and aluminum sample shot at a higher velocity than magnesium, according to how the alloy generated smaller pieces of shrapnel when compared with shrapnel from a magnesium test. CDP, using 25% alloy, was tested for blasting limestone by drilling 3.5-inch holes (89 mm) and inserting a 3-inch x 4-foot cardboard tube (76 mm x 1.22 m) with the mixture, packed to a density of 0.62 g/cm3 . The blast was initiated with an electric detonator, behaved like ANFO with more energy and fractured rock sufficiently across the entire length of the borehole. Seismic analysis determined that CDP produces lower ground vibrations than traditional explosives.

Jan 1, 2024

By S. F. Smith

Following a roof beam collapse on a major production district at the British Steel Corporation&apos;s Dragonby Iron Ore Mine, Scunthorpe, South Humberside, UK, rock mechanics investigations were undertaken in this room and pillar operation to assess the stability of workings throughout all the underground mine area. Over a four year period room convergence and roof sag were monitored in different mining areas and various junction configurations in order to assess and compare the relative movement of the strata resulting from mining activities, where varying rock bolt lengths and patterns have been utilised. The paper, after shortly describing geological aspects and mining methods, presents the research procedure adopted together with the instrumentation employed and discusses the results obtained during these investigations.

Jan 1, 1995

By Soraia Karolinne Castro Silva

Com o objetivo de analisar o nível de aderência e a qualidade dos Indicadores Ambientais, divulgados pelas empresas dos setores: metalúrgico, siderúrgico e de mineração, que fazem parte da BM&amp;Bovespa, foi feita uma pesquisa exploratória, qualitativa e de caráter documental, com base nos dados coletados nos Relatórios de Sustentabilidade GRI G3.1. Os Indicadores Ambientais foram analisados pelos métodos GAPIE (Grau de Aderência Plena) e GEE (Grau de Evidenciação Efetiva). Constatou-se que poucas empresas dos setores apresentam relátorios nomolde padrão internacional GRI, mesmo assim 58,33% apresentam algum tipo de evidenciação voluntária ambiental em seus web sites e 54,16% são ou já foram certificadas pelo ISSO 14001, demonstrando que a divulgação de ações de Responsabilidade Social Corporativa, ainda são tímidas nesses setores. Especificamente, os resultados obtidos através dos cálculos do GAPIE e di GEE mostram que, quando divulgados, os resultados são considerados positivos, levando-se em conta a média das empresas. Deve-se destacar que a pesquisa limita-se a análise apenas dos Indicadores Ambientais, nesse contexto os resultados dos cálculos de GEE e GAPIE não devem ser generalizados ao Relatório de Sustentabilidade como um todo.

Aug 16, 2017

By J. M. Hodge, H. M. Reichhold, R. D. Manning

The work reported in this paper represents the first of a series of investigations of the factors governing notch toughness in ferritic materials. This paper is concerned with two of these factors, namely, the effect of ferrite grain size, and the effect of an alloy content of 3.64 pct nickel. Every effort has been made to hold other variables constant in order to isolate the effects of these two. The compositions chosen for study were 0.02 pct carbon in order to eliminate the variable of carbide distribution, one steel being a plain carbon steel and the other alloyed with 3.64 pct nickel. Both steels were fully killed with silicon, without an aluminum addition, so that the variable of deoxidation practice was held constant. Finally, all samples were water quenched from 1200°F and tempered 24 hr at 300°F in order to hold the quench aging variable constant and to decrease the tendency for grain boundary carbide precipitation. The ferrite grain size was varied by heat treatment over the range of A.S.T.M. grain size numbers of about 2 to 6 in each steel so that the effect could be evaluated individually and the notch toughness of each steel could be compared at comparable ferrite grain sizes. Materials and Experimental Procedure MATERIALS The materials for this investigation were obtained from Battelle Memorial Institute as 250 Ib induction melts which were forged into 134 in. square bars and then rolled into 0.6 in. square bars. Both steels were deoxidized with silicon, the aluminum content being held to a minimum. Check analyses of these materials are shown in Table 1. HEAT TREATMENT FOR GRAIN SIZE The grain size was varied by varying both the cooling rate and the austeni- tizing temperatures. The heat treatments used and the corresponding grain size values are tabulated in Table 2. A semicontinuous network of grain boundary carbide was observed in the microstructure of both the plain carbon and nickel steels in the as rolled condition and an additional heat treatment was necessary to eliminate this variable. Therefore, all samples were water quenched from 1200°F and tempered 24 hr at 300°F as a final treatment before testing. This heat treatment served to eliminate to a great extent the grain boundary carbide network and to hold the quench aging effect constant. IMPACT TESTING Standard keyhole Charpy impact tests were machmed after heat treatment. A bath of acetone and dry ice was used for refrigeration of the samples down to temperatures of —94°F (—70°C) and a bath of either methyl-cyclohexane or isopentane, cooled by

Jan 1, 1950

Predictive chemical models facilitate the selection, design and assessment of aqueous chemical processes. The development of expertise in aqueous themochemistry has not matched the explosion in computer technology for modelling, which has placed pressure on the need for acquisition of skills to critically assess the appropriateness of the models produced. The &apos;blind faith&apos; culture which appears to be developing must be arrested by appropriate programs at the tertiary level and professional development strategies in the minerals industry.

Jan 1, 1996

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff&apos;s, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

By Hiury Voltz

Diversos são os defeitos que ocorrem durante o lingotamento contínuo dos aços. Um tipo de defeito de forma recorrente encontrado no lingotamento contínuo de jato aberto da ArcelorMittal Cariacica é a romboidade. O foco deste trabalho foi avaliar a influência da velocidade da água de refrigeração do molde, da velocidade de lingotamento, da lubrificação, do superheat e da conicidade na ocorrência de romboidade em aços de médio teor de carbono. Por meio da técnica de planejamento de experimentos, testes foram realizados para melhor compreender os efeitos de cada um dos fatores listados. Após análise estatística feita no MINITAB® versão 16.0, os resultados mostraram que a melhor condição, ou seja, as menores romboidades, foram encontradas reduzindo-se o superheat e aumentando-se a velocidade da água de refrigeração do molde, a velocidade de lingotamento e a taxa de lubrificação. O uso de moldes com menor número de corridas foi também outro fator que favoreceu a redução deste tipo de defeito.

Aug 16, 2017

By D. J. Judy, D. J. Rabovsky, W. H. Pailes, V. Castranova, K. Van Dyke, J. Rabovsky, N. A. Sapola, M. McPeek

"Platelet activating factor (PAF) can be released from pneumocytes following exposure to occupational dust (Am. Rev. Respir. Dis. 135:83, 1987). In addition, PAF has been shown to induce pulmonary inflammation, edema, and bronchoconstriction (Hosp. Prac. 19, 67, 1983). This investigation reports the effects of PAF on the properties of three types of cells found in the lung. PAF (1-100, K1/2 = 2.5 pH) caused depolarization of neutrophils as well as generation of chemiluminescence and secretion of hydrogen peroxide. These responses were dependent on the presence of extracellular sodium. However, PAF did not alter oxygen consumption of neutrophils. Although PAF (10 uM) caused depolarization of alveolar macrophages, no stimulation of chemiluminestence, superoxide secretion, or oxygen consumption was observed. However, PAF (10 uM). did potentiate chemiluminescence and superoxide secretion in response to zymosan (2 mg/ml) by 55% and 36%, respectively. In addition, PAF (10-90 uM) caused aggregation of alveolar macrophages. PAF (2-10 uM) also caused depolarization of type II cells, but did not affect membrane integrity or oxygen consumption. However, PAF (10-18 PM) enhanced the activities of two distinct forms of cytochrome P-450 in type II cells and caused aggregation of type II cells at PAF doses above 18 uM. These data indicate that PAF can affect the secretory activity of pulmonary phagocytes and the ability• of type II cells to detoxify foreign compounds (Bureau of Mines Grant - G1175142).INTRODUCTIONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acetylsn-glycerol-3-phosphoryl choline) which has been shown to Mediate a broad range of biological activities (1-3). Its pulmonary actions include contraction of pulmonary tissue (4), secretion of leukotrienes from leukocytes (5), airway constriction (6), pulmonary edema (7), and enhanced migration of neutrophils into the airspaces of the lungs (8,9).PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin (10-13). Therefore, PAP may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of PAF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type II epithelial cells."

Jan 1, 1988

By Thomas C. Jones

The purpose of this paper is to disseminate new information for nonelectric blasting in trenching and construction work. The presentation is not designed or intended to discredit conventional electric detonators or use of MS connectors and cord. Its sole purpose is to inform the S.E.E. of new and exciting benefits realized by the use of the Hercudet non-electric system in the construction industry.

Jan 1, 1984

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Zhijing Zhang, Ramana G. Reddy

"The viscosity of molten oxides is one of the important physical properties since viscosity has a decisive influence on fluid flow. The knowledge of the viscosity of molten oxides is essential for modeling and controlling of metallurgical process. In the present study, viscosities of high basic Na2O-B2O3 and Na2O-SiO2 binary melts and viscosities of Na2O-SiO2-B2O3 ternary melts were measured as a function of temperature and composition. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on the current experimental data, the previously developed viscosity model was modified. The characteristic features of viscosities of these melts have been discussed. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. IntroductionThe viscosity of molten oxides is one of the important physical properties since this property has a decisive influence on fluid flow, and is one of key factors to be taken into consideration in process modeling. The manufacturing operations require the viscosity of molten oxides to be within certain ranges. Although, some viscosity measurements on borosilicate systems have been carried out [1-4], the viscosity data in literature are available only for a few temperatures and cover small composition ranges. The agreement between the results of these works is not satisfactory [I-4]. Even the viscosities of binary systems Na2O-B2O 3 and Na2O-SiO2 generally are well studied, the available viscosity data in literature are only found in the composition range of O to 0.333 mole fraction ofNa2O. The aim of the present study is to provide a base with accurate experimental data for reliable model extrapolation."

Jan 1, 1999

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024

By Prasad Kopparthi, Narasimha Mangadoddy, Balraju Vadlakonda, A. K. Mukhurjee

"Column flotation (CF) is widely using equipment in mineral processing since many years. ERT technique facilitates non-invasive and nonintrusive visualization of different parameters in a column flotation. The hydrodynamic investigation of two-phase and three-phase are studied using electrical resistance tomography (ERT) coupled with pressure transducers in laboratory column flotation. Bubble size distribution, bubble rise velocity and gas and solids hold-up hydrodynamic parameters are extensively used for column flotation design and performance evaluation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas holdup and its radial distribution has been analyzed for both two-phase and three phase flows. Influence of solid particles on gas hold-up and its complete elucidation of dispersion in the column are assessed. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, were employed to explore the parameter study in two phase flow in column flotation.Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the `inside' flow behaviour of gas-liquid two-phase and gas–liquid–solid three-phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is being widely used in mineral processing industries in last few decades. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker and Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena et al., 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on the performance of column flotation (Finch and Dobby, 1991)."

Jan 1, 2018

By D. L. Babbitt, Sniezek

"This paper deals with the varions methods for the rapid Joading of unit trains which are being: used by ore procossors to move their product to dock-s1de storage facilities or their ultimate customer. Some of the techniques that have been used include (1) volumetrie loading, both in motion and static, (2) batch weighing into moving cars and (3) batch weighing into cars that have been stopped. Particular emphasis shall be placed on the two systems now in use at the Adams Mine facility of Jones and Laughlin Steel Corporation and at Cliffs of Canada's Sherman Mine. Typical ""turnaround"" times, loading rates, types of cars, weighing accuracies, material handling concepts and maintenance considerations shall be discussed."

Jan 1, 1969