Search Documents

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By J. P. Gliddon

Since 1980 a number of significant changes have been introduced at Palabora in an effort to off-set the effects of reduced product price and increased unit cost of inputs. These changes and improvements include major equipment rationalization programs, the introduction of trolley assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation and their contribution to cost reduction and improved productivity at Palabora are considered.

Jan 1, 1987

By Rolf Koenig

After the Dynatronic firing system was demonstrated for the first time at the SEE conference in Miami in 1987, it was officially approved in Germany at the beginning of 1993. Dynatronic has now been on the market for 5 years. At present, it is used in several European countries and successful test series have been running in Australia.

Jan 1, 1998

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986

By Maryam Ghodrat, Bijan Samali

Disposal of waste syringes in a safe and eco-friendly way has been an issue of considerable scale for decades. The generated amount of waste syringes has escalated with the rapid growth in population and wide acceptance towards single-use medical devices. Some hospitals have their own on-site incinerators ,but recent tightening of air quality regulations and landfill levies led to the closure of manyon-site incinerators. The solution to this problem implicates the development of an environmentally-sound method that would employ these waste materials. This work investigates a thermodynamic modelling approach for incineration treatment of waste plastic syringes in Electric Arc Furnace (EAF) steelmaking. Mass balance was obtained from HSC Chemistry thermochemical package. The results indicate that the rate of iron oxide reduction in the slag is higher when coke is partially replaced by waste plastic syringes. Furthermore, the amount of dust and stack gas emission was reduced by around 0.4% and 1.25% respectively by replacing 20%-weight of pure coke with waste plastic syringes. The study demonstrates part of the coke can be successfully replaced by waste plastic syringes in electric arc furnace to provide additional energy from combustion without affecting the main process.

Mar 1, 2018

The Golden Pig Mine is wholly owned by Bunnine Operations Limited and is located in the Yilgam Goldfields at Southern Cross, Western AustraliaThe paper briefly describes the geology and history of the operations. Mining is by shrink stoping, both hand held and mechanised. Advantages and disadvantages costs of the mining system are discussed.

Jan 1, 1993

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The history of Duluth commences with Daniel de Greysolon du Lhut, one of the explorers of the Upper Mississippi who came to the head of the lakes in the summer of 1679. Radisson and Groseillier, and Claude Allouez, a Jesuit priest, are supposed to have visited the head of the lakes, -but there is no authentic record previous to that of du Lhut.In 1792, the fur traders established a fort at Fond du Lac, fifteen miles up the St. Louis River from Lake Superior, but within the limits of the present city •of Duluth. In the early 50's, there were a few scattering settlers at Oneota and around the George Stuntz trading post on Minnesota point. In 1855-6, the settlement on Minnesota point was called Duluth, commemorating the name du Lhut, and organized as a town in 1857. The first board of trustees and town council consisted of -William Nettleton, J. B. Culver; Robert E. Jefferson, Grin W. Rice and William Old: In 1870, the city of Duluth was incorporated, and five years later a portion of the same territory was incorporated as the village of Duluth, and the two municipal corporations were still in existence on March 1, 1887, when the city and the village of Duluth were incorporated as the present city.The first saw mill in Duluth was erected in 1856-57, on the present site of the ship canal. It cut logs from a virgin forest at the upper end of Minnesota point.The first railroad was built to the head of the lakes in 1870. The charter for this road had been granted in 1861 to the Lake Superior and Mississippi Railroad Company, afterward called the St. Paul and Duluth, and which is now a part of the Northern Pacific Railroad."

Jan 1, 1920

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By Alok Tripathy

A simulation code called SIMJIG and the user interfaces have been developed using discrete element method (DEM) and the .NET platform respectively for the jigging process. DEM platform is used for tracking of particles in the jigging operation. DEM uses the net force balance on the particles to track the trajectory of the particle. Simulation results are compared with experimental results obtained by jigging of low grade iron ore lumps. Two different iron ore samples one from Chatishgarh and one from Odisha were used for the experimental studies. The Alljig? stratification test rig meant for batch laboratory experimental studies has been used in the present work. The behavior of different sizes of material on jigging has been examined. Later, the particle size behavior during jigging at different layers of the jig bed has been studied. Further stratification profile across the jig bed has also been studied. It was observed that simulation results are matching quite nicely with the experimental results. The SIMJIG simulator developed in the present study could be used for predicting the performance of the jigging operation effectively. Keywords: DEM, gravity concentration, jigging, iron ore, simulation

Sep 1, 2012

By Kallam V. K. Reddy, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

This work describes a leaching process for the conversion of high-magnesium peridotite rock, which is a chromite ore overburden, into two valuable products: magnesium salts and micro silica. Under normal leaching conditions, residue remaining after leaching is of a gelatinous nature and thus hinders the filtration process. To address this issue, oxidative leaching with the addition of H2O2 was employed, and it significantly improved the filtration kinetics. Four different approaches for H2O2 addition were tried, and they all proved effective in controlling gelation. The optimum oxidative leaching condition was 70 °C, 2 h time, 2 M H2SO4, 0.5MH2O2 and 400 RPM; under these conditions, 92% magnesium leaching efficiency was achieved. After leaching, the leach liquor obtained was purified and dried into Mg(OH)2 and MgSO4 salts. The leach residue contained mainly silica particles, with size in the 10–30 μm range. This material thus represents an attractive candidate for the production of highperformance concrete for the construction industry. The oxidative leaching process described here enabled the complete conversion of peridotite into valuable products, magnesium salts and micro silica.

May 5, 2020

By Hans Lundberg

Magnetic methods have been used for more than three hundred years in prospecting for magnetic ores. More recently magnetic methods have been used for finding salt domes and studying certain geological formations. A number of instruments have been developed and substantial improvements made as to their sensitiveness and accuracy. Papers and articles written on magnetic methods are generally elaborate and technical, and the average prospector finds it difficult to obtain the necessary information as to how to operate the simple magnetic instruments to the best advantage. The miner's compass, dip needle, and inclinator are, indeed, very useful instruments and are easy to handle, and a great deal of valuable information can be gained if the instrument is properly operated and the results correctly interpreted. The lack of knowledge of the fundamental principles, however, has caused a great deal of disappointment. Other and more elaborate geophysical methods have recently come into the limelight, and the prospectors seem to have lost a great deal of interest in the dip needle. This is much to be regretted, because magnetic methods have a particular field of use. The present article is an attempt to help the prospector regain interest in the magnetic instruments and to show the use and application of a simple magnetic survey. If the prospector expects some useful help in his work, he must, of course, know the instrument, know how to take the readings, and know how to plot and interpret the observations.

Jan 1, 1929

IN the extra-mural service being built up by the Engineer-ing Societies Library as its finances permit, an occasional large total charge is incurred for exceptionally protracted services. A western steel company, for example; was charged the unusual fee of $500. They wanted complete informa-tion on transverse tests of steel, and asked the library to compile copies of all accessible records. Weeks -of search-ing and photoprinting produced three volumes of data. Two years afterward the company's chief engineer told the director of the library that the cost seemed high when the bill was paid but that the volumes had been in constant use. The information had been worth thousands of dollars. A client who wishes to pay no more than a moderate fee for services can state to what limit he is willing to go. Thus he may specify that he would like searches made on a particular subject but that he does not wish to exceed $5 or $30- for the information. The library is as willing to perform a small service as a large one.

Jan 3, 1928

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968

By P B. Schwann

The commonly accepted genetic theories of Pilbara iron ores and Woodie Woodie manganese ores have often presented them as quite unique. This apparent uniqueness is not confined to just iron and manganese, but is also seen in gold and copper deposits in Western Australia. The published material on iron and manganese ores would seem to have either a quite complicated genesis or none at all. An alternate theory for the origin of these deposits is presented which involves a protore with simple oxidation and pH controls with hydrothermal fluid sources from the diagenesis and dewatering of the underlying strata. This theory explains the distribution, thinning, cold dolerites and very high concentrations of deleterious minerals observed in these deposits. This genesis system is also related to the systems that deposit hydrothermal gold and copper in sediments in the region.This paper presents the author’s observations, sampling and mapping after several decades studying and exploring for the minerals in Australia and locations overseas. All of these theories were developed with (or in spite of!) the guidance of Mal Kneeshaw, but would never have seen the light of day without him and the others presenting here. It is not what I would call scientifically polished, and possibly deserves more detailed studies; it is, however, presented as a discussion paper.CITATION:Schwann, P B, 2015. Related genesis for iron, manganese and gold-copper ores in Western Australia, in Proceedings Iron Ore 2015, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Michael E. Stout

The recovery of the constituent components of spent lead acid batteries was pioneered in the early 1970's by M.A. Industries, Inc. MA's main reason for research and development in this area was to recover the polypropylene casings for use as feed stock in their injection molding plants. At that time spent and reject casings were either disposed of or being fed with the lead 'bearing materials into the ,smelting process. M.A. has since developed, built and operated plant for the conversion of scrap casing into reusable copolymer resins. The system is composed, of washing, .sizing, extrusion and pelletizing the polymer into a form which is ready to be injection molded into new products.

Jan 1, 1995