Search Documents

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By Zhou Jiemin

A mathematical model is developed to determine the economic thicknesses of refractories and insulations in rectangular furnaces, Both the heat loss cost and the lining investment are taken into account to achieve a minimum operation cost. For the sake of calculating the heat flux, the paper is particularly concerned with the simulation of the three-dimensional transient heat conduction processes in the lining and a Douglas-Rachford method is used to solve the finite difference equations, The model has been used to design an industrial electric resistance furnace operated periodically. the values of temperatures and power consumption measured from the furnace correspond with the model results.

Jan 1, 1991

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By Maria I. De Rosa

Combustible materials, when burned, produce toxic gases and smoke, which may vary dramatically from one material to another, with resultant different total toxicity and smoke obscuration levels. This U.S. Bureau of Mines report presents smoke property data acquired for a variety of mine combustibles and shows that there exists a correlation between the smoke properties, the relative toxicity, and the smoke obscuration levels of those combustibles tested. These correlations can be used to devise simple, standard tests for determining the toxic and smoke obscuration hazards of mine materials during fire.

Jan 1, 1989

By H. C. Gunning

The Privateer is the major mine of the Zeballos mining camp; with a total production from May 1937 through the first half of 1946 of $5; 610; 423 from 139; 254 tons of ore. This includes a small production from the connected Prident mine. The entire operation was closed from October 1943 to November 1945.

Jan 1, 1954

By Sanaz Mosadeghsedghi

The feasibility of the application of electrodialysis in separation of light and heavy rare earth elements (REE) in synthetic solutions was investigated. The experiments were carried out using single and binary solutions of a light (cerium) and heavy (ytterbium) REE. The effects of electrical voltage, electrical current, and the addition of complexing agent (EDTA) to increase the separation selectivity were investigated. Separation of Ce and Yb was achieved in binary solutions with and without the addition of EDTA. Higher degrees of separation were seen at higher voltages. Ce–Yb separation was more significant in the presence of EDTA. The separation factor of Ce–Yb and Ce–Yb-EDTA were 1.44 and 2.60, respectively.

By James Norman, Oliver C. Ralston

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by Froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each or clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1942

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

By Oliver C. Ralston, James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by Froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each or clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1942

By Robert F. Love

Deep under the hills of southwestern Wyoming lies a nonmetallic mineral deposit of incredible dimensions and value. This nearly pure, horizontal bed of the mineral trona, a sodium sesquicarbonate (Na2HC0,.NaHC08.H20), is found in the Green River formation some 1500 ft below surface. It is believed that evaporation of an ancient saline lake left this sodium carbonate as the evaporite and mysteriously left practically no sodium chloride, which is the common constituent of an evaporated saline lake. The trona bed averages 10 ft in thickness and extends over an area of several hundred square miles. In 1938 a geologist with the U. S. Geological Survey identified the trona in the core from a former oil exploration drillhole. By so doing, he initiated the developments of a chemical industry of impressive growth in the area, an industry on the threshold of further and much more spectacular growth. A drilling program by the Union Pacific Rd. and Intermountain Chemical Co. in the early 1940's succeeded in blocking out mineable reserves of several hundred million tons. Development of the deposit started in 1946 with the sinking of a 12-ft diam, concrete-lined shaft 1500 ft deep-followed by construction of a small pilot calcining plant. Actual mining of the trona started in 1947 and continued on a limited scale until 1953, when the $15 million surface facilities were completed, along with the second shaft and other expanded underground facilities. Since April 1953 the mine has been producing more than half a million tons per year, from which the refining plant has produced more than 300,000 tons per year of high quality soda ash.

Dec 1, 1956

By Andrew Dobson

The assessment and control of environmental noise from mines has become increasingly important in recent years, due to urbanization and population growth, increased regulation of environmental factors, and overall awareness and sensitivities to noise exposure. Minimizing adverse effects on communities and achieving compliance with local ordinances is now commonplace, and consideration of noise during the design and/or operation of a mine cannot be ignored. Ventilation equipment can represent the loudest and most bothersome equpiment at mines, however there are complexities when attempting to control the assocaited noise, due to the acoustical nature of mine vent fans. In fact, the utilization of traditional and/or industry standard methods can intensify the noise impact, or simply not work as intended. This paper provides recommendations on specific noise control methods that are suitable for mine ventilation equipment, based on recent assessment work and field experience.

Oct 1, 2024

By Fernanda Santos da Luz

Nas últimas décadas, houve um aumento da aplicação de fibras naturais lignocelulósicas (FNLs) como reforços de compósitos poliméricos em diversos setores industriais, principalmente no segmento automotivo. Esse crescente interesse em FNLs se deve não somente aos benefícios ambientais, mas também às vantagens técnicas, econômicas e sociais. Dentre as FNLs, destacam-se as fibras de coco e as fibras da folha do abacaxizeiro (PALF) que são produtos residuais do cultivo de suas respectivas frutas e, por isso, possuem baixo custo e são abundantemente disponíveis. As características físicas dessas fibras se diferem bastante, sendo o PALF caracterizado por suas fibras longas e diâmetro equivalente relativamente baixo. O presente trabalho avaliou o desempenho das fibras de coco e PALF em testes de pullout com o objetivo de caracterizar o comprimento crítico e a adesão interfacial dessas fibras na matriz de epóxi. Os resultados mostraram um comprimento crítico 65% maior para a fibra de coco em relação ao PALF, o que indica maior adesão interfacial do PALF com a matriz epóxi e pode ser atribuída a superfície naturalmente mais rugosa do PALF.

Oct 30, 2017

By Kadri Dagdelen, Lee J. Zamalloa

Modern surface mining operations are always seeking for minimizing costs while increasing production rates, among the optimization of other specific tasks that have an impact on the economics of the mine. Specifically, the cost related to the production fleet operation (shovels and trucks), the maximization of the overall performance of the equipment, and the uncertainty to meet the goals at the end of the operational time horizon are always topics of discussion with no apparent simple answer. On the other hand, truck-shovel dispatch systems based on Linear/Non-Linear Programming Algorithms have been in operation since mid-1990’s with different levels of success depending on the correct arrangement of operational resources and the complexity of the mine, but having in most cases some important shortcomings related to the way these systems deal with the decision making of the operational objectives, being necessary to have a human agent (dispatcher) to guide the system when the operational parameters change, creating the possibility of suboptimal decisions due to the human factor. This paper discusses the implementation of a novel methodology based on AI techniques to assist in the decision making of the best goal selection when operating a Fleet Management System, taking into consideration time periods as variables and integrating them as part of the analysis, providing a better overview of the forecast plan completion with respect to previous production numbers and evaluating best alternative to handle future events to minimize losses or maximize profits, resulting in better truck assignments, minimum shovel idle times and overall productivity improvements of the operation at the end of the time horizon.

Jun 25, 2023

By A. K. Mahto, B. Samanta

"A heuristic model was developed to simultaneously generate the ultimate pit and production scheduling at a mining project. The method consists of a preprocessing step to select a starter pit, the implementation of a genetic algorithm to optimize the pit and schedule of the starter pit, and a network-flow algorithm–based postprocessing operation to finalize the ultimate pit and production scheduling. Applied to an iron ore mine, the model pit and schedule produced a net present value 21% higher than the reference pit and schedule prepared by experienced field engineers.RÉSUMÉ Un modele heuristique a ete developpe pour generer simultanement l’ordonnancement de la fosse finale et de la production dans le cadre d’un projet minier. Cette methode comprend une etape de pretraitement visant a selectionner une premiere fosse, la mise en oeuvre d’un algorithme genetique pour optimiser la fosse et le calendrier d’execution de cette premiere fosse, ainsi qu’une operation de posttraitement basee sur des algorithmes de flux reseaux pour finaliser l’ordonnancement de la fosse finale et de la production. En l’appliquant a une exploitation de minerai de fer, ce modele de fosse et d’ordonnancement a genere une valeur actualisee nette (VAN) superieure de 21 % a l’approche de reference pour la fosse et l’ordonnancement developpee par des ingenieurs de chantier chevronnes. INTRODUCTIONLong-term planning for an open-pit mine involves two important activities: developing the ultimate pit and determining the optimum production schedule. To accomplish this, an ore deposit is discretized into a number of smallsized elements called blocks, which are presented in a 3D block model structure. Because of economic and slope criteria, only a certain set of mining blocks can be extracted from the deposit constituting a pit. During mining, these blocks must be extracted in a specific sequence known as the production schedule."

Jan 1, 2017

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

By Robert G. Benson, David M. Jones

The San Luis deposit of Costilla County, Colorado contains 11,021,000 tonnes (12,149,000 tons) of ore at 1.4 g/t (0.040 oz/st) gold in two mineable zones. Gold mineralization is associated with silicification and quartz-sericite-pyrite alteration localized in breccias along a low-angle "detachment" fault zone in Precambrian gneiss. Gangue minerals include chlorite, specularite, chalcopyrite, molybdenite, and fluorite. Mineralization is mid-Tertiary in age and may have an indirect genetic relation to the emplacement of felsic intrusions. Portions of the ore body are unconformably overlain by sedimentary rocks of the Tertiary Santa Fe Formation. The deposit formed during the early stages of extensional tectonism along the eastern edge of the present day Rio Grande rift.

Jan 1, 1990

By W. N. Marchant, P. T. Brooks, P. B. Altringer, R. O. Dannenberg

The US Department of the Interior, Bureau of Mines conducted laboratory tests to devise a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 ppm W (70ppm WO3). Using ion exchange resins synthesized by USBM chemists, 98% of the tungsten was extracted from the brine and 92% of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44% tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process research unit to provide more reliable data for an economic appraisal

Jan 1, 1980

By I. H. Bonekamp

Norddeutsche Affinerie has operated an Outokurnpu type flash smelter for more than 25 years. In recent years, the concentrate smelting capacity was increased to 750,000 tpy, double of the initial design capacity. Maintaining this high performance level requires very good metallurgical process control. It is not enough to base this control on thermodynamics and kinetics since the furnace is highly dynamic. Understanding these dynamics and being able to quantify them can have significant financial benefits. A mass and energy balance model was developed and is discussed based on measured data. At this time the model is based on the major elements copper, iron, sulfur and silica. With it is possible to quantify the differences of the various material streams such as matte, slag, flue dust, matte carry-over to settling furnace, etc. Comparing the reconciled energy balance model with the fundamental thermodynamic model makes it possible to quantify the dynamics. These dynamics are related to input parameters using methods such as statistics and neural nets. In the future this database will be used to improve the understanding of the dynamic process as well as the dynamic process control.

Jan 1, 1999