Search Documents

By A. U. Seybolt

A. U. Seybolt (General Electric Research Laboratory)— As pointed out in an earlier paper,41 it appears to be very difficult to nucleate Si3N4 in Si-Fe of silicon content up to around 5 pet. Therefore, one observes, as did Pearce, that equilibrations with nitrogen gas yield only nitrogen in solid solution at temperatures above about 700°C, or, as Pearce found, 770°C. Evidently, the free energy of formation of Si3N4 only becomes high enough at -770°C to overcome the reluctance of Si3N4 to nucleate. However, as mentioned in Ref. 41, if some Si3N4 is first formed by a mixture of ammonia and hydrogen, one can then replace this gas mixture by nitrogen gas, and either increase or decrease the amount of Si3N4 present at any temperature by suitable adjustment of nitrogen pressure: that is, to equilibrate with Si3N4. In the equilibration experiments cited in Ref. 41, equilibrium was approached from both sides, and it was found that samples up to 944oC, at least, were in equilibrium with Si3N4. Higher temperatures were not employed, as this would have necessitated a redesign of the apparatus for using nitrogen pressures in excess of 1 atm. To summarize, the results of Pearce's experiments and those of Ref. 41 cannot be directly compared because two quite different equilibria were studied. Therefore, the statement by Pearce on p. 1398 indicating apparent error in Ref. 41 is unjustified. M. L. Pearce (author's reply)— There was limited evidence obtained in the current investigation which would indicate that excessive "supercooling" did not occur. A small piece of the same resulting from heat treatment No. 5 in Table III was subsequently held at 800°C for 16 hr in 95 pet N-5 pet H. Isotope-

Jan 1, 1964

By R Burgess-Limerick, D Lynas

A number of standards and guidance materials currently exist to assist equipment designers. The ISO process, however, is a formal process and change often lags behind technology development. In some cases, this may result in weak or ineffective standards that need to be written in general terms to accommodate future technology developments, meaning some standards may only establish minimum requirements and not be overly helpful to equipment designers, in particular when designing for workforce diversity and inclusivity. By contrast, advisory information as issued by various mining regulatory bodies is able to respond more quickly to changes in technology. Standards do however have a safety and productivity focus providing design consistency between equipment manufacturers, a basis for auditing purposes, assistance in mining regulation and compliance, and in the development and application of safety management systems. As an example of challenges facing equipment designers, ISO3411 (2020) provides data approximating the 5th, 50th and 95th percentile of the ‘earth-moving machinery operator population’ for numerous static dimensions relevant to the design of earth-moving equipment. These data are then utilised in ISO6682 (2020) to provide recommendations regarding the location of controls. Attempting to utilise the data provided in ISO3411 (or other sources of static anthropometric data) creates further challenges for equipment designers, in that reference percentiles is problematic for design purposes. There is no ‘5th or 95th percentile operator’ as individuals vary along each dimension (Robinette and Hudson, 2006). Although dimensions have some degrees of correlation, when multiple dimensions are considered, the range of individuals which fall within a given range on all dimensions reduces substantially. For example, only about 82 per cent of individuals in a population will fall within the 5th to 95th percentile ranges for both height and weight. The more dimensions are considered, the smaller the range of people who actually ‘fit’ the description.

Apr 16, 2024

By R. Keith Evans

Potential large scale uses in secondary battery systems and fusion reactors together with a steady increase in demand for conventional applications, particularly in aluminum smelting, has resulted in an increasing interest in lithium and its compounds. Current world requirements are met from both granitic pegmatites and non-pegmatitic sources and although the emphasis in this short paper is on the pegmatitic minerals, and, in particular, on their "direct usage" applications, a short summary of other sources and requirements for chemical production is included for the sake of completeness.

Jan 1, 1977

By Felix M. Zhuravlev, Vitalij P. Lyalyuk

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

Ore samples from the South, Central and North ore-bodies of the King Cassilis Mine, near Omeo, Victoria, were broken and transported to Melbourne for experimental metallurgical treatment. A microscopical examination of individual unoxidised specimens, selected from these samples, was undertaken in order to thro'w as much light as possible on the occurrence of the gold which forms the valuable economic mineral in the ore.The following descriptions are the outcome' of this examination and show that very minute particles of free gold are mechanically associated with the sulphides. While the gold may be separated from the transparent gangue minerals by the flotation of the sulphides, the, actual size of the particles indicates that it is impossible to separate all the gold from the sulphides by grinding the ore to pass through a screen of 200 mesh in which the average width of the holes is 0.063 mm. Chemical disintegration of the sulphides is essential to free all the gold particles and render them available to the attack of chlorine or of a solvent.It is interesting to recall that a metallurgical investigation on the Cassilis ore in the same district by K. A. Mickle in...

Jan 1, 1933

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co. purchased the first pumpcrete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms.

Jan 4, 1954

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By K. E. Prince, S. Burling, R. J. Ring, M. K. Maley, W. R. Taylor

Vanadium occurs as a component of carnotite, which commonly occurs in calcrete type ores, and in association with uranium in some sandstone-hosted deposits. Increasing demand for vanadium, which is used in high-strength steel and Vanadium Redox Flow Batteries (VRFBs), is offering some uranium producers a potential option for by-product vanadium recovery to improve project economics at a time when uranium prices are low. This paper presents the results of recent optimisation studies on the Bigrlyi deposit for the recovery of both uranium and vanadium. The impact of carbonate leaching conditions on uranium and vanadium extraction from a range of carnotite-in-calcrete ores is also examined, with vanadium extraction limited by the proportion of non-carnotite vanadium present in the ores. The findings are particularly relevant to developing projects as results show that elevated vanadium content in ore does not necessarily equate to a high vanadium extraction in leach.

Jan 1, 2020

By Hu Meilong, Liu Lu, Bai Chenguang

Extracting perovskite from high titanium-bearing blast furnace (BF) slag is a green and potential method to recover the second titanium resource. The non-isothermal crystallization process of perovskite in synthesized high titanium-bearing slag was studied in situ by confocal scanning laser microscope (CSLM) with cooling rate of 20 K/min. The results showed that perovskite was the primary phase formed during cooling process in the titanium-bearing synthesized slag (TiO2=23%). Perovskite started to precipitate at 1719 K and finally presented an orthogonal straight lines morphology.

Jan 1, 2014

By J. D. Noll

The Mine Safety and Health Administration (MSHA) has promulgated rules to limit the exposure of metal/nonmetal underground miners to diesel particulate matter (DPM). These rules have resulted in many types of control tech­nologies being implemented including diesel particulate filters (DPF). The passive type DPF is the most desirable because it requires little maintenance and it regenerates while the vehicle is operating. One problem with passive DPFs is that many vehicles cannot develop the sustained exhaust temperatures needed to initiate DPF regeneration, and thus it is required that the DPF be catalyzed to decrease the temperature needed for regeneration. In some past studies, such catalyzed filters have been shown to cause an increase in the nitrogen dioxide concentrations in the exhaust, resulting in a potential health hazard. In this study, a lightly catalyzed DPF along with a fuel-born catalyst were employed to help reduce the DPM emissions from a 980F loader used for cleanup in a stone mine. After 30 days of use, the filter continued to regenerate successfully at the exhaust temperatures generated by this loader, substantially reduced DPM concentrations emitted in the exhaust, and did not cause a measurable increase in nitrogen dioxide levels that could be attributed to the device.

Jan 1, 2009

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

Government established and financed the NZ Steel Investigating Co in 1960. Its investigations showed that a steel industry was feasible and desirable based uponNorth Island titanomagnetite ironsands, and charted a route for its establishment. The initial processing used post-1945 preheating and prereduction developments, but later innovative improvements created what was essentially a new New Zealand technology. Of the North Island titanomagnetite deposits: the small ones at Waipipi were best made available for export; those at Kawhia and Taharoa were too remote for the economic siting of a mill; that at Raglan proved too small; while at Waikato North Head three times the requirement of 50 million tons of concentrate were located in two sand areas averaging 18 per cent titanomagnetite. Economic studies showed that a South Auckland site would be ideal, close to New Zealand's biggest market. The mill site, on a basalt flow at Glenbrook, was located by a half-day's fieldwork - near both the Waikato North Head deposit, and a railhead for bringing in Waikato coal, etc, and taking out steel products.   This development was one of several since World War II which altered significantly the lives and homes of New Zealanders (others were natural gas, oil, geothermal power, epithermal gold, aluminium, opencastable lignite, etc). All had the essential ingredients of the highest government backing, direct or indirect government finance, and first-class New Zealand scientific and engineering skills (eg to create new technologies). Not one such project failed.

Jan 1, 1993

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By Long Han, A. V. Kalinin, Xiujian Luo, Xiaobo Wang, Xiaoou Xia

"Inertia vibration crusher is a kind of vibration equipment which crushes ore by vibration. When the inertia vibration crusher works, ore between the two moving jaws is subjected to the high frequency contact force, which is produced by the two moving jaws with high frequency synchronous reciprocating motion. The synchronous motion of the two moving jaws depends on the self-synchronous feature of the inertia vibration crusher. To study the self-synchronous feature of the equipment, the dynamic model was established, in which relative parameters were taken into consideration. The kinematic coupling relations of the assemblies are discussed, and appropriate calculation method is chosen to solve the vibrating differential equation. Whether the two vibration exciter can realize synchronous operation depends on the ability of the vibration system's capture moment. Results show that though the two rotors’ motors and damping coefficients are different, and two jaws’ damping and stiffness coefficients are also different, as angular velocities of the two unbalanced rotors reach a certain value, the vibrating system can be stable. Their angular velocities tend to be equal, and the swings of the two moving jaws can be the same. The horizontal vibration and swing of the frame are large in a few seconds after starting the machine. When the system runs stably, the horizontal vibration and swing vanish, and the vertical vibration is stable. The study and its results can provide reference for the optimization design and parameter setting of inertia vibration crusher and related vibratory equipments.INTRODUCTIONMaterials can be easily broken by using the inertia force of the vibration exciter, which can effectively realize the selective crushing, reducing excessive combinations and the energy consumption, as introduced by Zhang in 2005. The initial micro crack between crystals in the material increases and new cracks can be manufactured because of the high frequency impact and the extrusion of the vibration crusher, so vibration crushing equipment can make it possible for any high strength brittle material to be broken theoretically. Inertia cone crusher and inertia vibration crusher have been successfully used in the treatment of metallurgical slag and construction waste, and it verifies the efficiency of vibration crushing."

Jan 1, 2016

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017