Search Documents

By Charles J. McMahon

In a recent paper, Floreen and Hayden report that additions of the noble metals iridium, rhodium, ruthenium, and platinum to Fe-C alloys containing 0.03 to 0.08 wt pct C act to significantly reduce the ductile-to-brittle transition temperature in a notched-bar impact test. They compare these results with the similar, well-known effects of nickel and manganese additions, and they note that this supports the hypothesis that addition of austenite stabilizers enhances notch toughness. Although not attempting to offer an explanation for this, they suggest that it might be found in an alteration of the bonding characteristics of the bcc lattice of iron by additions of elements which tend to stabilize the fcc lattice. While this suggestion appears to have some merit, it should perhaps be held in abeyance until two more likely possibilities have been explored. It is now fairly clear that the beneficial effect of manganese derives from its ability to promote a globular carbide morphology instead of the platelike form found in grain boundaries and pearlite patches in Fe-C al10~s.' Previous work14 has also shown that cleavage fracture in Fe-C alloys of the type tested by Floreen and Hayden originates almost exclusively in the cracking of cementite platelets, and that the ductile-brittle transition temperature is very sensitive to the volume density and size of these carbides. Treatments which lead to development of nonlamellar carbides or fine dispersions of carbides, such as quenching and tempering or appropriate alloy additions, promote toughness by removing the primary mode of cleavage initiation. The effectiveness of manganese in this regard has long been known. Nickel appears to behave in a similar manner, though the effect is perhaps not as dramatic as with manganese.15 However, nickel additions do lead to a definite refinement of ferrite grain size following a given transformation heat treatment, and this in itself acts to greatly enhance notch toughness.'' (The grain sizes of the various heats tested by Floreen and Hayden were not reported, so it is not known how much influence this factor exerted in their results.) In conclusion, it is suggested that one should consider the well-established effects of alloying elements on carbide morphology and ferrite grain size before resorting to more complex possibilities, such as modification of interatomic bonding.

Jan 1, 1969

By V. Annamalai, J. B. Hiskey

Abstract-The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol-1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol-1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 6, 1978

Although a formal EES was not prepared for the WIM project due it winding down, CRA Ltd has been through the EES and planning scheme amendment process for its demonstration plant. Community consultation was involved with all aspects of this process. The paper outlines the WIM EES consultation program and provides lessons for future community consultation for major projects in regional locations with significant potential to alter the environment.

Jan 1, 1992

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By H. S. Geismer

Campbell,&apos; in 1896 said: "The Birmingham district in Alabama has certain great advantages for there are few places in the world where fuel and ore are so near together, although, unfortunately, both are of inferior quality; the ore being low in iron and high in phosphorus and the coal giving a weak and impure coke." This statement could not have been questioned in 1894, but by 1896 several Robinson-Ramsay washers had been put into operation and weak and impure coke was a thing of the past. The Warrior coal field of Alabama contains six seams that yield coking coal of excellent quality. In descending order, they are Brookwood, Milldale, Pratt, America, Mary Lee, and Black Creek. In each of these, however, bands of rock and bone coal of varying thickness are stratified with the coal; and while some of these impurities can be separated from the coal by the miner, much of it must be loaded out with the coal. Consequently, unless the coal is washed before being coked, it will yield a coke of varying ash and sulfur content quite unsatisfactory for blastfurnace use. At present, the Gulf States Steel Co. is producing run-of-mine coal at its Virginia mine, from the America seam, that is uniformly low enough in ash to permit of coking without washing, but this is the only exception to the above statement. Alabama was the first state to experiment seriously with coal washers, was the first to install washers on a large scale and, up to the present, has maintained the lead. The Alabama State Mine Inspector reports that during 1923 20,919,303 tons of bituminous coal was mined in Alabama; 12,858,499 tons of which was delivered to coal washers for treatment.

Jan 1, 1925

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothermic reduction, hydro metallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By John D. Wiebmer

Lignite Development in North Dakota is a "shotgun wedding" according to former state senator Robert L. Stroup-the unwilling groom (North Dakota) is being led to the altar by the nation&apos;s demand for increased coal production. The state&apos;s attorney general, Allen I. Olson, reacts to the situation this way: "We have no specific coal policy. We plan to keep the whole matter down to a dull roar and drag our feet until we see how we fit into the national energy picture." But despite a state administration labeled as "cautiously negative" toward resource development, North Dakota has experienced a twofold increase in annual lignite production within the last two years. And within the next four years, three more mine additions will double the state&apos;s output again.

Jan 8, 1977

By Dan Mancuso

This case study is an example of how Encyle/Texas, Inc. (a subsidiary of ASARCO) responded to various socio-economic forces by converting an idle zinc hydrometallurgical refinery into a metals recycling facility. The facility accepts metal-laden process waste streams and produces various "synthetic ores" which are sold back to industry. Acceptance and reactions by industrial, political, economical and regulatory interests towards the project are also discussed.

Jan 1, 1992

By Andrew F. McKown

Overbreak and damage to rock walls at the perimeter of rock excavation can lead to safety problems due to rock falls and additional costs due to a] extra mucking, b] extra concrete or shotcrete to backfill overbreak, c] additional rock reinforcement, d] additional water inflow and e] additional maintenance of rock walls. To minimize these undesirable effects, there are several perimeter control techniques available (i.e. line drilling, cushion blasting, pre-splitting, smooth blasting, and fracture control blasting) which control perimeter hole spacing, burden and loading to provide a smooth, stable excavation contour. Conventional perimeter control loading and hole spacing is satisfactory for massive, homogeneous formations, but when blasting in weathered or fractured rock closer spacing and very light loading is required.

Jan 1, 1984

By Paul Shimizu

BHP Robinson contracted Minnovex Technologies to implement a Comdale Expert System at their greenfields operation in Ely, Nevada. The expert system has resulted in a significant increase in tonnage. Other benefits have also been realised, including a reduction in operation upsets (having a positive effect on downstream processes, i.e. flotation) and reduced production variances between crews. The expert system is written in a unique manner using trend based logic with minimal hard limits. The result is a robust system that requires minimal operator supervision while producing very high results. The development, success and acceptance of the system can be attributed to the strong team that was assembled for this project. The team not only consisted of BHP Metallurgists and Minnovex but most importantly included operations.

Jan 1, 1998

The advantages of coordinate geometry in design and construction of underground works are apparent for reasons of flexibility, security, computer operations, survey error analysis, and the use of numerical techniques for setting out and checking works. Integration with National or State survey systems is useful in the long term, both at design, construction and future works stage. Equipment and methods are available which permit "absolute" monitoring of structures and strata over long periods,to close toler- ances. This work can be carried out in the limiting urban environment. Rapid data acquisition by semi-automatic devices, or photogrammetry, utilizing electronic data processing is capital inten- sive, but provides more data than analogue surveys (i.e., setting out centre lines) and becomes more attractive with increased labour Costs.

Jan 1, 1976

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

This surveillance report summarizes data on work-related fatal and nonfatal injuries, illnesses, and hazardous exposures in the mining industry for the 10-year period 1986-1995. The term "surveillance," as used in public health, may be new to many readers of this report. With regard to occupational safety and health, the goal of surveillance is to describe the occurrence of work-related injuries, illnesses, and known hazardous exposures; to identify new hazards that may occur due to the introduction of new technology or other factors; and to assess the effects of preventive measures designed to improve worker safety and health. Surveillance provides an overall picture, which can be used to focus resources on areas most in need of prevention programs or further research. Surveillance generally requires the use of multiple sources of data, all of which have their own strengths and limitations. Surveillance in the U. S. mining industry is complicated by the fact that U.S. national data systems that provide information on mining are based on two different definitions of the mining industry. One is established by the Mine Safety and Health Administration (MSHA), the other by the Standard Industrial Classification (SIC) System [Office of Management and Budget 1987] and the 1980 U. S. Bureau of the Census (BOC) Classification System [U.S. Bureau of the Census 1982]. The mining industry as defined by MSHA is based on the regulatory jurisdiction of that agency. Reporting requirements for injuries, illnesses, and workplace exposures are stipulated under the Federal Coal Mine Health and Safety Act of 1969 and the Federal Mine Safety and Health Amendments Act of 1977. Of note is that the oil and gas extraction industry falls outside of MSHA jurisdiction. The Occupational Safety and Health Administration (OSHA) was charged with enforcement in the oil and gas industry under the Occupational Safety and Health Act of 1970. Under the SIC, the definition of mining covers the extraction of naturally occurring minerals, including liquids (petroleum), gases (natural gas) and solids (coal, metal, and nonmetallic minerals). Exploration and development of mineral properties are also included in the SIC definition of the mining industry. The SIC was developed by the Office of Management and Budget for use in classifying establishments based on the type of economic activity in which they are engaged and serves as the industry classification standard for all establishment based Federal economic statistics. This classification is important for occupational safety and health surveillance because it also serves as the industry classification system for all data on work-related injuries and illnesses collected by the U.S. Bureau of Labor Statistics (BLS). The U.S. Bureau of the Census uses an industry coding scheme similar to that used by the SIC. For the mining industry, the categorization is identical in both systems. Death certificate data made available by the National Center for Health Statistics (NCHS) are categorized under this system. Death certificate data are particularly important for surveillance of mortality from work-related illnesses. Key differences between the SIC/BOC categorization system and the MSHA system can be summarized as follows: • MSHA excludes the oil and gas industry, which is classified as part of the mining industry under SIC/BOC. • MSHA excludes work that is done off of mine property; work off of mine property is included under SIC/BOC if it is performed by an establishment falling into one of the SIC/BOC mining industry codes. • MSHA includes mine-associated mills and processing plants; these are classified under the manufacturing industry, rather than mining, according to the SIC/BOC coding structure. Since the data collected by MSHA and the data collected by BLS and NCHS using the SIC/BOC classification system are both important sources of information on the mining industry and in many cases serve different purposes, data from both systems are presented in this report. In general, data using the SIC/BOC system are comparable across U.S. industries and should be used when comparing mining to other U.S. industries. Much of the data in this report are presented in the form of frequencies or rates. A frequency provides only a count of the number of cases without providing any information about the risk of occurrence. Rates provide an estimate of the risk of injury or illness. The reader is cautioned, however, that rates based on small numbers can be unstable; thus, any inferences should be drawn with care. In this report, no rates are presented for groups in which there were fewer than three cases. The incidence of most injury and illness conditions differs by age, sex, and race. For this reason, data in many surveillance reports are adjusted for these demographic factors. It was not possible to do this for most of the rates in this report because information on demographics was not available. With the exception of the proportionate mortality ratios (PMRs), all data presented are unadjusted. A detailed account of the sources of data is in appendix A. The methods used in data selection and analysis are described in appendix B.

Jan 5, 2000

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003

By Paul W. Jeran, Vladimir Adamek

Characteristics of surface deformations i.e., sub¬sidence, inclination, curvature and horizontal strains, are evaluated, based on information obtained by direct field measurements over three longwall panels in the Northern Appalachian Coalfield. Surface deformations have been precomputed using Bals&apos; and Knothe&apos;s theories. The results have been compared with Bureau of Mines field data to evaluate the applicability of the two theories to the U.S. min¬ing conditions. Measured horizontal movements and the resulting horizontal strains differ as much as 300 percent from precomputed values. Topography has no detectable effect on vertical movements but appears to have substantial effect on the development of horizontal strains. The horizontal deformations computed from our field measurements generally exceed the limits used in other countries to protect surface structures.

Jan 1, 1982

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969