Search Documents

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013

By H. EI-shall

In this paper, the results of bench scale testing of five different flotation processes to separate dolomite from phosphate are discussed. The effectiveness of each process interms of phosphate recovery and MgO content in the concentrate is used together with the reagent consumption as the basis of comparison. The water quality is found to play a major role in the performance of these processes. Effect of water hardness as well as other parameters are discussed.

Jan 1, 1995

By John D. Wiebmer

There are those in the Colstrip, Mont., area who can still remember the opening of the Rosebud mine in 1923. For 35 years it was a steady employer of 80 or 90 residents who produced coal for the railroad. In 1958, though, mining ceased as diesel locomotives supplanted steam engines. The mine was purchased in 1959 by Montana Power, the parent of Western Energy Co., and production resumed in 1968. Long Construction Co. was chosen as operator of the mine equipment. At that time, reserves appeared virtually unlimited. The thick Rosebud seam coursed through alternate sections of railroad holdings and federal land-then came the federal moratorium on coal leasing in 1971. About the time Western Energy completed the special leasing procedure to extend reserves from an existing mine, a new federal monkey wrench was thrown into the works with passage of the Surface Mining Control and Reclamation Act of 1977.

Jan 12, 1979

By Morrison R. D, Kojovic T

Industry-sponsored research at the Julius Kruttschnitt Mineral Research Centre has produced models of high tension roll and electrostatic plate separators operating in mineral sands dry plants. The behaviour of mineral species has been characterised under a wide variety of operating conditions by extensive plant machine sampling and laboratory measurements. The effect of operating conditions on separator performance has been quantified by monitoring changes in the weight distribution of mineral species along the product splitter axis. The response of each mineral species has been modelled on a size-by-size basis using an average surface charge decay time and a variation in its surface properties. The models incorporate changes in machine, mineral and ambient conditions on the separation and predict all product flows, assays and size distributions. This paper outlines the structure of the models. These models are being implemented in JKSimSand, an user-friendly simulation software Package.

Jan 1, 1991

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By M. Y. Mohassab-Ahmed

In an effort to develop a novel flash ironmaking process, the chemistry of selected slags was investigated. In different ironmaking processes, the molten bath (iron-slag bath) is expected to be in contact with gas atmospheres of H2/H2O, CO/CO2/H2/H2O, and CO/CO2. The latter was investigated to allow comparison with the blast-furnace conditions. The slag composition was selected to resemble that of the blast furnace with CaO/SiO2 in the range 0.8 to 1.4. The temperature range was 1550 to 1650°C. The oxygen partial pressure was maintained in the range 10-10 to10-9 atm. The effect of water vapor on the chemistry of the slag as well as the equilibrium reactions involving the slag has been studied for the first time. H2O dramatically affects the chemistry of the slag and strongly affect the phase equilibria in the slag as well as the equilibrium distribution of elements between slag and molten metal.

Jan 1, 2014

Tyre cost at Mount Morgan Limited had been 24% of the truck operating cost. Comprehensive tyre testing resulted in a reduction in tyre costs of about one third. A record of the evaluation techniques may enable the selection of tyres that are most suited to particular conditions. Rubber characteristics, rubber quantity, tyre design, road conditions, dump conditions and inflation pressure were found to be sig- nificant variables. Measurements of tyre temperatures at the breaker strip were used to select the tyre design and inflation pressure required for Mount Morgan Limited's conditions. Relugging of tyres was discontinued as a result of tyre testing.

Jan 1, 1974

By David Mast, Irwan Halim, Brian Hagan, Kaveh Talebi, Jason Edberg, Amanda Foote

On June 14, 2023 Jay Dee Contractors’ Tunnel Boring Machine (TBM) “Phoenix” holed through and completed mining the second drive of the I-75 Segment 3 Storage and Drainage Tunnel. Completion of the tunnel came only after overcoming several challenges, including a groundwater intrusion event which deposited thousands of cubic yards of wet ground material into the tunnel. This paper will discuss the events which delayed completion of the tunnel by over nine months, the risk management and construction approaches assumed by the Design-Build team during bid, several challenges faced by Design-Build teams when building stormwater resilience tunnels using traditional Department of Transportation standards, and recommendations for improving risk allocation and proposal documents for future similar Design-Build tunnel projects.

Jun 23, 2024

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"A cellular model of the plastic deformation of polycrystalline aggregate is proposed and comprehensively described. Representative volume element (RVE) of a solid body, that is being deformed, is described as a population of interconnected units that, in turn, can consist of lower scale level units. Sliding along the various allowed sliding systems deforms simple units, which do not have an internal structure. For consideration of stress distribution within the limits of components, the approach of self-consistent field is used. Rotation of units and moment stresses connected with it are taken into account. Results of computer experiments are analyzed.1. IntroductionMicromechanical models of polycrystals are a link between the research of plastic deformation on micro and macro levels. Computer simulation of inelastic strain of polycrystals has found a great deal of interest as well. Despite the fact that this approach does not allow to obtain macroscopic constitutive relationships that are used in deformed solid body mechanics, it clarifies essential features of the phenomena in many aspects. First of all, it concerns effects stipulated by interdependence of micro-level and macro level of plastic deformation processes. Also, with the computing mechanics, instead of constitutive relationships, the adequate computer models can be used. Broad possibilities for computer simulation of various processes are opened by cellular automata approach. By means of numerical experiments, the cellular automata allows to study the macro behavior of the whole ensemble of cells depending on the local microscopic laws that define evolution of each cell and its interaction with the closest environment.We propose a mathematical model of a polycrystalline aggregate (the cellular model) based on a self-consistent scheme and on the interaction law similar to the one by Berveiller and Zaoui [1]. Our original solution is the self-similar structure of cellular automata that allows modeling of the fractal nature of real materials (Figure 1). The goals of this work are to present the major structures and relations of cellular model of polycrystal and to test this model for its adequacy as for describing known effects and dependencies. Identification of the model and its application for studying of concrete polycrystals are put aside for the future research."

Jan 1, 2001

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world's production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978

By Mazandarani M, Chabot L, Vichion K

Pitch-steering models have been developed for discretely advanced mining machines (such as heading machines and coal shearers) using small-angle geometry and there are illustrative examples of simulator predicted performance. Although simple linear models result from the analysis of open-based machines, sledge mounted machines require execution of a Linear Programming energy minimisation to determine the attitude of the machine base at each advance over the previously cut floor steps. An analytical approach is based on elastic beam concepts developed for such applications as longwall face conveyors, caterpillar tracked machines such as continuous miners and longhole drills. Simulation results for longhole drills show the expected performance of an automatic guidance system and the destabilizing effects of sensing deviation too far behind the drill bit. Certain drill bit boundary conditions are expected to assist TBM. steering studies in three dimensions.There is a real role in mining machine steering for the mathematical models used in flight simulators.

Jan 1, 1991

By Thomas J. Blalock

The volumetric determination of uranium according to the method of Sill and Peterson (6),3/ which uses cerate oxidimetry after the separation of interferences such as sulfides and cupferrates, has been used for some time by the Bureau of Mines and gives satisfactory results for many of the samples tested. However, in those instances where the uranium content did not exceed a few tenths of 1 percent and iron was present in the range of 10 to 40 percent (as Fe203),4/ the method was cumbersome and unreliable. The need for a more accurate procedure for the determination of small amounts of uranium in the presence of large amounts of iron, such as in shale or black sands, prompted this investigation. The Bureau desired that materials containing as little as 60 p.p.m. of uranium be assayed within reasonable limits of accuracy. One of the primary aims of this work has been to eliminate, as far as possible, the necessity for repeated cup ferron extractions.

Jan 1, 1960

By A. S. Eve

The detection of magnetic dykes by using magnetic variometers is the oldest application of. geophysics to mining, and is also one of the more simple and certain methods 0f locating such deposits. As a result of recent improvements in the instruments, it is now possible to find the dyke, deter-mine with magnetic variometers its strike and dip', with fair accuracy, and to estimate the approximate depth of overburden when there is no outcrop. The application of electrical methods may be used to distinguish mineral from diabase dykes. The authors have had an opportunity of making surveys with the modern Askania types of vertical and horizontal variometers over magnetic dykes in the Sudbury region. The interpretation of the results has been confirmed by diamond drilling in some cases, and by experiments over models. The variometers used were the standard form of Askania instruments (1). The sensitivity of the horizontal type was 17.2 gammas per division, and that of the vertical variometer double this quantity. To make a preliminary survey of the district, parallel lines were laid off two hundred feet apart running north and south, and readings were taken with the vertical variometer every 100 feet along these lines. This can be done very rapidly, and when an indication of a magnetic deposit is found, the readings may be taken every hundred feet, or less if the size of the deposit warrants smaller intervals. If the deposit is a vein or dyke, the readings along the adjacent lines immediately indicate the strike of the body. Thus the presence and strike of a magnetic dyke, whether of mineral value like the pyrrhotite and nickel deposits of the Sudbury district, or simply a worth-less diabase dyke, is simply and rapidly found.

Jan 1, 1932

By Andy Judge

"In traditional Permanent Magnet Machines, such as electric motors and generators, power is transmitted by magnetic flux passing through an air gap, which has a very low magnetic permeability, limiting performance. However, reducing the air gap through traditional means carries risks in manufacturing, with tight tolerances and associated costs, and reliability, with thermal and dynamic effects requiring adequate clearance. Using a magnetically permeable, high thermal conductivity material has the potential to improve magnetic performance, while at the same time offering performance advantages in heat transfer.Ferrofluids can be used to improve permeability in the rotor I stator gap. However, there are several tradeoffs in this approach. Fluid immersion comes with an increase in fluid friction loss compared to the windage losses of a traditional system. Isolating the rotating components from the ferrofluid can offset this effect. Also, while the magnetic effect can be positive for gap permeability, leakage flux can increase, and saturation can limit gains. These effects must be taken into account for a system optimized for ferrofluid immersion.IntroductionPermanent Magnet Machines (PMM's) convert electrical energy to mechanical energy in motor applications, or, for generator applications, convert mechanical energy to electrical energy through means of passing alternately polarized magnets past electrical coils. Looking at a simplified version of a PMM, where Rx is magnetic reluctance and <l>x is magnetic flux, we have the circuit shown in Figure 1."

Jan 1, 2013

By J. G. Groppo

Lowering of filter cake moisture of ultra-fine coal to a 20 percent level using conventional vacuum filtration could be achieved using a combination of metal ion and surfactants. Pretreating coal slurry with about 0.2 Kg/ton of a surfactant and 50 ppm of copper or 10 ppm of aluminum ions provided filter cake containing 22.8 percent moisture. The lowering of moisture is explained due to formation of hydrophobic micro-agglomerates which facilitates dewatering.

Jan 1, 1994

By Gregor de Ratmiroff

Field prospecting for bauxite in Venezuela has had a long but interrupted history having till now oferred but evidence of occurrences. The Venezuelan Government, trough the Corporación Venezolana de Guayana (C.V.G.), in 1974, formalized a major effort in prospection for bauxite in the Shield area and the Orinoco Delta in orden to establish the possibility of raw material supply to an upcoming and expanding aluminium industry. The Corporation, in turn, created and delegated to the Division of Geological Stu- dies, the formulation of the necessary infrastructure and execution of work in orden to determine the existence of economically exploitable bauxite deposits.

Jan 1, 1979