Search Documents

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By The Staff

BEFORE going into detail on the subject to be presented, a brief outline of the Company's earl y history would not be out of place. Prospecting and mining on a small scale was started in 1876 on the site of the present open pit at Thetford Mines. The property was purchased from the Crown in 1878 and Johnson's Company was incorporated in 1885. It is owned and operated today by descendants of the original shareholders. Many employees, through their fathers and grandfathers, have service records dating back three generations. The principal asbestos deposit at Thetford Mines is pear-shaped, with surface dimensions of about 2,200 feet in length by 1,300 feet in maximum . width. Its long axis strikes northeast and the dip is nearly vertical, but irregular in detail. It is known to extend to a depth 1,200 feet below the original surface, but its area at that depth has not been determined. Ownership of this deposit is divided among three active Companies: the Asbestos Corporation, Limited; Bell Asbestos Mines, Limited; and John-son's Company. Johnson's Company owns a section about 1,000 feet in length and 500 feet in width, bounded on the northeast by the King mine of the Asbestos Corporation and on the northwest by the Bell pit. On Johnson ground, there was originally a large outcrop o~ asbestos rock which dipped toward the south below overburden. This was mined until recently by open pit, the overburden being stripped off as far southward from the original outcrop as was economically possible. As the. pit was deepened, within side walls maintained at a maximum safe slope, its floor area, of course, became progressively smaller, and eventually the pit would have wedged out against the Bell property line. It became necessary, there-fore, to introduce some other method of mining before production became seriously curtailed by a shrinkage of the pit area.

Jan 1, 1941

By Mahin Rameshni

WorleyParsons innovative SO2 reduction process efficiently recovers sulfur from SO2 streams. Effluent gases from ore roasters and smelters and coal-fired power plants can be treated to reduce sulfur emissions. This exciting new process is an innovative combination of well-established processes of reaction of CH4 and sulfur vapor to produce CS2, followed by catalytic hydrolysis of CS2 to H2S, and Claus reaction of H2S and SO2 to sulfur. Key advantages are lower fuel consumption, reduced emissions, better product sulfur quality and better operational stability. The Production of elemental sulfur from SO2 is being called Rameshni SO2 Reduction (RSR) and it is patent pending.

Jan 1, 2006

By Ken Woloschuk

??Owners?Perspective ??Owners?Challenges ??EcoNomics?Delivery Model ??Projects ??Project Outcomes ??Questions ??Balancing the triple bottom line initiative: ?shareholders expectations of economic costs and benefit; ?stakeholders expectations of social and environmental costs and benefits; ?deciding what is sustainable and which design alternatives are the most sustainable. ?? Delivering required project outcomes

May 1, 2008

By A. J. Lynch, W. J. Whiten

Extensive research, ,development and plant application work has been done on automatic control systems for wet grinding and sulphide flotation circuits during the past twenty years. The result is that there is a good understanding of the process mechanisms, the effects which changes in different variables have on these processes, the procedure for design of control systems to satisfy particular objectives and the problems in the implementation of control systems. There is also an appreciation of the problems which are still to be solved. These are reviewed briefly in this paper. Other processes used for the beneficiation of fine particles have been studied in lesser detail. The control of dry grinding, coal flotation and gravity separation are mentioned briefly in this paper.

Jan 1, 1980

By Gerald H. Luttrell, Joe Shoniker, Jaisen N. Kohmuench, Christopher J. Barbee, Michael J. Mankosa

The HydroFloat technology was specifically developed to upgrade phosphate sands that are too coarse (>0.6 mm) to be efficiently recovered by conventional flotation methods. In this novel process, classified feed is suspended in a fluidized bed that has been aerated using an external sparging system. The air bubbles selectively attach to particles that have been made hydrophobic through the addition of a fatty acid collector. The teetering effect of the fluidized bed forces the low-density bubble-particle aggregates into the overflow, while hydrophilic particles are rejected as a high solids content underflow Since the HydroFloat is actually a density separator, the process can treat much coarser feeds than would be possible using traditional flotation processes. In addition, the high solids content of the teeter bed promotes bubble-particle attachment and reduces the cell volume required to achieve a given capacity. This paper presents test data from ongoing pilot-scale trials of the HydroFloat cell in the phosphate industry.

Jan 1, 2002

By J. W. Matousek, C. S. Samis

me thermodynamic properties of the components in the Cu-Ni-S ternary system have been studied by measuring the H2S/H2 ratios in a gas phase equilibrated with the molten matte at 1200°C. The measured sulficr potentials have been extended by extrapolation and combtned with previously published data to permit the thermodynamic analysis of the ternary system by integration techniques. A simplifying assumption of ideality in the Ni3Sz-CuS pseudobinary has been made. SINCE copper and nickel metals were first extracted from their sulfide ores the interaction between the two metals and sulfur has been of industrial and theoretical interest. The processes developed to extract copper and nickel have been reported periodically in the literature. The theoretical studies on the Cu-Ni-S ternary have been restricted to problems directly associated with production. It is only within recent years that the binary systems related to this ternary have been analyzed thermodynamically and mathematical devices developed to permit a corresponding treatment of the ternary system. In 1910 an investigation of the role of nickel in Cu-Ni-Fe-S mattes was reported,' It was concluded from this work that nickel is not an element replacing iron in mattes, but rather that Cu-Ni alloys behave as a single metal during the matte converting operation. The laws which govern the converting of Cu-Ni alloys were found to be the same laws as those that govern the conventional converting of copper alone. Although considerable information has been reported on the theoretical aspects of copper smelting, little data is available on the smelting of Cu-Ni ores except for phase diagrams and process descriptions. The available information on the Cu-Fe-S ternary and related systems prior to 1953 has been summarized by Ruddle.2 Since Ruddle's publication, Rosenqvist and coworkers have completed phase equilibria investigations of the Fe-S, Co-S, and Ni-S binaries,3 the Fe-S-O ternary,4 and the Cu-Fe-S-O quaternary.4 An extensive investigation of the Cu-Fe-S ternary system at smelting temperatures has been made by Krivsky and Schuhmann.5 At these temperatures, the Cu-Fe-S system is very similar to the Cu-Ni-S ternary with respect to the location of the single-phase and two-phase liquid matte regions. In the former, however, the area of immiscibility is more extensive and the region of liquid matte-liquid metal-solid metal equilibria is much more extensive. Krivsky and Schumann observed that the Cu2S-FeS pseudobinary system is, for practical purposes, an ideal mixture. This investigation has served as a valuable guide in analyzing the Cu-Ni-S ternary. EXPERIMENTAL The experimental procedure employed in this investigation was the conventional technique of equilibration of the sulfide matte with gaseous mixtures of hydrogen and hydrogen sulfide at 1200°C. The thermodynamic properties of sulfur (S2) in the gas phase are determined by means of Eq. [I] and the activity of sulfur in the matte by Eq. [2].

Jan 1, 1963

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962

By E. G. King

Many of the rare-earth oxides are now commercially available in pure form and they have a variety of potential technical uses. Thermodynamic data for these oxides, however, are rather sparse. It is one of the functions of the Bureau of Mines to fill the need for this type of information. This report gives the results of low-temperature heat-capacity and high-temperature heat-content measurements by the Bureau of Mines of lanthanum sesquioxide. The entropy at 298.15° K. was evaluated and heat-content and entropy increments above 298.15° K. were obtained to 1,800° K. The results were combined with the known heat of formation at 298.15° K. to derive heats and free energies of formation at higher temperatures. Sufficient information is now available to permit reliable thermodynamic calculations involving lanthanum sesquioxide within the temperature range 298° to 2,000° K.

Jan 1, 1961

By M Fishwick Tapia

This paper was prepared and translated from the final report of the investigation into the Codelco Chile Salvador DivisionÆs air blast which occurred in the Inca-West area. In this section of the block cave mine, a stable arch formed covering an area of approximately 15 000 m2 . This zone subsequently collapsed producing a massive air blast. The collapse followed a series of planned extraction activities and occurred on 5 December 1999. This paper discusses the cave back arching event and the measures that were taken in order to induce the controlled collapse. This was to minimise risk to personnel, equipment and installations. The results obtained to date are presented.

Jan 1, 2000

By M. A. Mahboob, T. Celik, B. Genc

Mineral Resources estimation plays a crucial role in the profitability of the future of mining operations. The conventional geostatistical methods used for grade estimation require expertise, understanding and knowledge of the spatial statistics, resource modelling, geology, mining engineering as well as clean validated data to build accurate block models. However, the geostatistical models are sensitive to changes in data and would have to be rebuilt on newly acquired data with different characteristics, which has proved to be a time-consuming process. Machine learning methods have in recent years been proposed as an alternative to the geostatistical methods to alleviate the problems these might suffer from in Mineral Resource estimation. In this paper, a systematic literature review of machine learning methods used in Mineral Resource estimation is presented. This has been conducted on such studies published during the period 1990 to 2019. The types, performances, and capabilities, of several machine learning methods have been evaluated and compared against each other, and against the conventional geostatistical methods. The results, based on 31 research studies, show that the machine learningbased methods have outperformed the conventional grade estimation modelling methods. The review also shows there is active research on applying machine learning to grade estimation from exploration through to exploitation. Further improvements can be expected if advanced machine learning techniques are to be used.

Nov 30, 2022

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By S. Forgeron

Presentation ? Introduction ? Canadian Underground Coal Mines ? Standardization of Geological Assessment ? Geomechanics Base-line Studies of Canadian Coal Mines ? Cape Breton Development Corporation Prince Mine ? Quinsam Coal Corporation ? 2 North and 4 South Mines ? Smoky River Coal Corporation 5B-4 Mine ? Conclusions and Baseline Comparison ? Figures

May 1, 2001

By Wendell S. Williams

Single crystals of TIC doped with boron at high temperat~ires develop second-phase inclusions. The inclusions are in the form of lamellae lying parallel to {l 11 } planes of the Tic matrix and can be vevealed by etching [100] cleavage faces of the boron-doped Tic crystals. measurements of the critical resolved shear stress. t, of TIC crystals containing such inclusions showed that the ropid drop in t wilh increasing temperatu.ve found for pure Tic was greatly reduced. At 1600°C, the inclusion containing crystals had a value of t five limes that of pure Tic. The hardening effect also was found to inhibit hot pressing of TiC powders containing boron impurity. Thermochemical and crys-tallographic arguments suggest that the inclusions are TiB2. The boron content of the hardened carbide is a few tenths of 1 pct. TITANIUM carbide is noted for its high room-temperature hardness. However, measurements of the critical resolved shear stress, T, of single crystals of Tic at high temperatures have shown that t decreases exponentially with increasing temperature.' This temperature dependence of t is attributed to thermally activated dislocation mobility limited by a large Peierls stress.' In turn, this large Peierls stress is believed to be a consequence of strong co-valent and ionic binding in Tic. The rapid drop in 7 with increasing temperature, characteristic of pure Tic, is lessened by the introduction of second-phase inclusions. Exposure of Tic to boron at high temperatures produces such inclusions. A report of the influence of boron on t in Tic is presented, followed by a discussion of the nature and formation of boron-containing inclusions in Tic which are believed to be responsible for the hardening effect. I) CRITICAL RESOLVED SHEAR STRESS OF BORON-DOPED Tic CRYSTALS Tic single crystal boules grown by Union Carbide Corp., Linde Division, were doped with boron by placing them in a carbon crucible packed with boron powder and heating in a vacuum furnace to 2000°C for 1 hr. Samples 1 by 1 by 3 mm were cleaved from these doped boules. High-temperature compression tests' were made on these samples to determine the critical resolved shear stress as a function of temperature . The rapid drop in critical resolved shear stress found for pure Tic crystals' did not occur: tests indicated that the boron-doped crystals at 1600°C had values of T equal to those of pure Tic crystals heated to only 1100°C, Fig. 1. No difference in the shape of the individual stress-strain curves was produced by the boron doping, but the stress scale was multiplied by a large factor. The hardening effect of boron in Tic probably extends to temperatures lower than those used in the present work (1100°C minimum). At room temperature, however, the influence of boron is difficult to determine because the stress required for gross plastic flow in pure Tic is SO high that in practice fracture cccurs first. Microhardness is the only test that can give an indication of the yield stress in Tic at room temperature. such measurements were made5 on boron-doped Tic; the matrix had a hardness value

Jan 1, 1967

Objective To develop and evaluate the effectiveness of safety training tools specific to the underground hard-rock mining industry. Background Scaling, the removal of loose rock from the roofs and walls of a mine by manual or mechanized means, may be necessary during any stage of mining. Manual scaling is very labor intensive, and mechanical methods can be too powerful and actually produce a less stable roof.

Jan 1, 2001

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By Nicholas J. Grant, Italo S. Servi

THE creep and stress rupture properties of three grades of aluminum have been reported in a previous paper.' It was found that the stress coefficient of the creep rate and of the rupture time changes at the transition from low temperature-type to high temperature-type deformation. The transition corresponds to the equicohesion for grains and grain boundaries. In order to support the conclusions obtained from the examination of creep and stress rupture data, the deformed specimens were observed metallographically and a few special tests were conducted. The results of these qualitative observations are given in the present paper. Experimental Procedure and Results Table I gives the types of aluminum specimens.' The creep and stress rupture tests were conducted in simple tension at constant stress. Further details on the experimental techniques have been given.' The test bars were electropolished in a perchloric-acetic mixture before testing and were observed after testing without any further preparation unless otherwise specified. Observations of specimen cross-sections were made after electrolytic polishing and etching. The samples were extended along a direction parallel to the longer side of the micrographs of Figs. 12 through 27. The log-log plots of stress vs. minimum creep rate for the three grades of aluminum appear in Figs. 1 and 2. The reference numbers on each curve help relate the photographs to the conditions of testing, indicating where high temperature-type deformation and failure prevailed and where low temperature behavior prevailed. Deformation of Single Crystals at Very High Temperature: An annealed, high purity aluminum specimen was slightly strained at one end and re-annealed. A large single crystal was formed at the strained end of the specimen during re-annealing; the other end remained polycrystalline (see Fig. 3). A stress of 50 psi was applied to the cold specimen to avoid loading at 1100°F. The temperature was then raised to 1100°F, kept at 1100°F for 3 hr, and lowered again to room temperature. Fig. 4 shows the appearance of the specimen after testing. The single crystal deformed by gliding along parallel planes, while the polycrystalline part deformed mainly by grain boundary flow. Some grain growth occurred in the polycrystalline part. Another high purity specimen, which had two large single crystals at the two ends and a polycrystalline zone in the middle portion, was tested at 1000 °F under a stress of 100 psi. The appearance of the sample after test is shown in Fig. 5. Even though considerable slip occurred in the single crystals, the fracture occurred in the weaker polycrystalline portion. Evidence of Grain Boundary Migration during Creep Testing: A high purity, coarse grained specimen, which had a large crystal in the middle portion (see Fig. 6) was tested at 700°F under a constant stress of 175 psi for 30 hr. The appearance of the specimen after testing (Fig. 7) indicates that the large crystal deformed by gliding along parallel planes, while the rest of the specimen deformed mainly by grain boundary flow. Microscopic examination showed clear evidence of grain boundary flow and grain boundary migration, an example of

Jan 1, 1952

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium, and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. This work presents a thermodynamic analysis of a monazite system and discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extractions and low acid consumption. Rare earth extractions as high as 80% were achieved, while iron and thorium extractions were lower than 1%, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature