Search Documents

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By R. Todd Swinderman

Variations in designs between belt cleaner systems are so wide that it is impractical to establish a dimensional stan- dard. The number of variables that affect the efficiency of belt cleaners is too great to assume a required number or style of cleaners for broad classifications of bulk solids or typical applications. The amount of carryback remaining on the belt is more dependent upon the characteristics of the bulk solid and the physical parameters of the conveyor system than it is on tonnage of material conveyed. Therefore, a performance-based standard is proposed. Three levels of cleaning performance are proposed: • Level I cleaning is general specified when concerns about carryback are not critical. Cleaning systems normally associated with achieving a Level I performance are single or double cleaner systems with one-piece blades undergoing poor to average maintenance. Frequent cleaning of the carryback that falls from the return run will likely be required. • Level II cleaning is generally specified when carry- back is of concern but does not create a safety or environmental problem. Cleaning systems normally associated with Level I1 performance are multiple cleaner systems with segmented blades undergoing the manufacturer's specified maintenance. Regular but infrequent cleaning of the carryback that falls from the return run will likely be required. • Level III cleaning is generally specified when con- cerns about carryback are critical. Concerns range from safety to environmental to product contamination. Cleaning systems normally associated with achieving a Level 111 performance are multiple cleaner systems in conjunction with at least one low- volume water spray. Scheduled inspection and the manufacturer's specified maintenance would have to be performed to maintain a high level of cleaning performance. Difficult-to-clean bulk materials may require the use of a washbox system with multiple cleaners using a combination of low-volume eater sprays to lubricate the cleaners and high-volume sprays to keep the washbox and discharge piping freely flowing. Further addition of a water and sludge recycling system reduces the amount of water that ends up in the product to a negligible amount. Very infrequent cleaning of the carryback that falls from the return run will be required. PURPOSE The purpose of this proposal is to propose a standard method for specifying belt cleaner systems based on user expectations and equipment performance over time. DEFINITION In bulk solids handling by conveyor belt, carryback is the material that adheres to the belt after the belt discharges its cargo. PROPOSED STANDARD Required Basic Good Practices There are a number of basic design and operating principles that are good practice for the selection, installation, and maintenance of belt cleaning systems on conveyors in order to achieve "standard belt cleaning performance over time. 1. The Belt Cleaning System shall be designed to meet the performance requirements based on the worst operating conditions and worst bulk solids proper- ties that are expected. 2. Each conveyor discharge point shall be designed to readily accept the manufacturer's recommended minimum number of belt cleaners. In addition, the discharge chute shall be designed to accept, with minor modifications, at least one additional cleaner if it is required.

Jan 1, 2004

By Morris Muskat

It is pointed out that the application of capillary pressure curves obtained by drainage or desaturation processes to the calculation of the fluid distribution in interphase transition zones involves a number of difficulties; namely: (I) the development of very low nonwetting phase saturations appears to be in contradiction with the lack of mobility of such distributions indicated by permeability-saturation curves, (2) dispersed nonwetting phases are thermodynamically unstable, and (3) discontinuous phases should not be subject to hydrostatic equilibrium requirements. While these difficulties could be obviated by assuming that the capillary pressure drainage curve has an initial horizontal segment, they are automatically circumvented by application of the imbibition capillary pressure curve to the lower part of the water-oil transition zone. These generally show zero displacement pressure at only partial wetting-phase saturations. The countercurrent upward flow of oil into the main oil-saturated pay and downward drainage of water also suggests that wetting phase imbibition processes will control the saturation distribution immediately above the water-saturated section. Similar considerations, with a generalized interpretation of the apparent wetting-phase behavior of the oil and gas phases, provides a basis for constructing the curve for fluid distribution in the oil-gas transition zone. In the transition zones so derived, the oil begins with a nonvanishing saturation at the water-oil contact and terminates with a similar saturation at the top of the gas-oil contact. The gas-oil transition zone begins with an equivalent nonvanishing gas saturation. Introduction It has been a common assumption for some years that the nature of the fluid dis- tribution in virgin reservoirs, and in particular that in the transition zones between the oil and water and between the oil and gas sections, can be computed by a simple application of capillary pressure data. The results of such calculations appear to have been first reported by Leverett.' The latter, however, indicated only the numerical values of the parameters used in the computations, without explicitly describing the procedure. Leverett's illustrative calculated transition zones are reproduced in Fig I. Although no critical study of the apparently obvious method of calculation has been published, one cannot proceed very far in the computation without encountering some rather fundamental questions not yet answered in the literature. This paper is not written under the pretense that the whole transition-zone problem has been fully and satisfactorily solved. Its purpose, rather, is to discuss suggestions for its treatment, much of it admittedly hypothetical, and emphasize the nature of the uncertainties arising therein; for the literature, as now available, gives little indication that there are any problems still outstanding. The Transition-zone Equation The basic equation, which presumably gives directly the fluid distribution without recourse to any further consideration, is: Ap = (r1 - r2)gh [1] where r1, y2 are the densities of the two contiguous fluids, h is the height above the "capillary-free" zone of complete saturation with fluid I, g the acceleration of gravity, and Ap is the capillary pressure across the average interface at the height

Jan 1, 1949

By J Moncrieff, P Bellairs

The Black Star Open Cut is located immediately adjacent to the township of Mt Isa and is situated in the middle of extensive pre-existing infrastructure including two concentrators, two smelters, a wet fill plant and two shafts. At any one time there are in excess of 500 people working on the surface within an industry-accepted 600 m exclusion zone from Black Star blasts. Apart from the surface operations there are also the underground operations including the lead mine (closed in December 2005) and the Enterprise and X-41 mines that must clear for all Black Star blasts. The application of industry standard blasting exclusion zones (600 m) was risk assessed as imposing operationally prohibitive constraints which could cause significant business interruption due to the logistical challenges required to ensure that all personnel from surface plants were evacuated for each blast and potential for lost production whilst these personnel were not operating the plant. In was therefore an imperative for the blast exclusion zone to be reduced. This was achieved by the: use of a QA/QC team to ensure that relevant drill and blast implementation is within an acceptable tolerance (KPIs) from design; use of high-quality stemming material called HMR, which is a by- product of the concentrating process and is generally sized at -14 mm with very little fines; implementation of appropriate training and support to Black StarÆs own blast crews, reinforcing the need to achieve the designed amount of stemming in every hole; and provision of appropriate support from Black StarÆs management for additional resources to ensure that every blast achieves design within the KPIs but especially in high-risk areas. The blast exclusion zone was successfully reduced after monitoring the flyrock results from more than 176 blasts. Black Star Open Cut now maintains a minimum blast exclusion of 200 m in critical areas; however, general blasting currently uses a 250 m exclusion as this provides additional risk management whilst still minimising the logistics associated with clearing and securing the slightly increased area.

Jan 1, 2007

By Bezuidenhout M, Moolman D. W

In the minerals industry numerous problems cannot be solved by conventional mathematical models owing to their complexity or a lack of phenomenological understanding. Neural networks provide one way of mapping the ill-defined relations between process variables and functions for such ill-defined problems. Consequently, processes such as leaching and froth flotation are mostly controlled in an empirical way by using rules of thumb. In addition, these processes involve so many independent and dependent variables that the plant operator finds it difficult to visualise or even observe a change in process conditions. The structure of froths developed on the surfaces of industrial scale froth flotation cells has a significant effect on both the grade and recovery of valuable minerals in the concentrate. Although these effects are well known at the process operational level, where considerable heuristic knowledge is available, little work has been reported on a detailed characterisation of the mechanisms and the visual characteristics of the surface froth. Recent results from an on-line observation of froths in several plants have proved the relationships between image features representing froth behaviour and metallurgical results. It will be shown how supervised and unsupervised neural nets are being used on operating plants to interpret computer vision data. In froth flotation the operator is supposed to visually observe process changes from the appearance of the froth, which is an unreasonable demand under industrial conditions. The system described here determines textural parameters on-line, and tracks the changes in process conditions via a Self-Organising Map (SOM) neural net. This monitoring system warns the operator about fluctuations in reagent addition, and gives an idea of the type of froth encountered. In another example, changes in the mineralogical characteristics of gold ores are represented on an SOM map, based on the diagnostic leaching behaviour of such ores.

Jan 1, 1997

By C. P. Fiske

The pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers, and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance come the condensers, as large numbers are used in the manufacture of spelter, and improvements in quality result in material decreases in working cost. While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are conccrned. Materials Bond Clay.—The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather it in the accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later) accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons with the clay as usually handled.

Jan 1, 1918

By F. Habashi

Magnesium is the eighth most abundant element in the earth's crust, It occurs in nature in sea water, brines, and a number of minerals, Metallic magnesium was first isolated by Humphry Davy (1778-1829) in England in 1808 via electrolysis of anhydrous magnesium chloride with a mercury cathode, Antoine Bussy (1794-1882) in France extracted the metal in 1828 by reducing fused magnesium chloride with metallic po¬tassium vapour, The first industrial production of magnesium by electrolysis of molten carnallite began in 1886 in Hemelingen in Germany, In 1940 Lloyd M, Pidgeon (1903¬1999) in Canada pioneered the first industrial metallothermic magnesium extraction plant based on the reduction of dolomite with ferrosilicon under vacuum, Since then the magnesium industry developed further and a variety of processes are presently used.

Jan 1, 2006

By Charles H. Dowding, Catherine T. Aimone

Rock particle sizes were measured at fourteen steep-slope Appalachian coal mines during production blasting. The distribution of rock sizes shows the effects of inter-hole timing, sequence of hole initiation, as well as charge distribution within each shot. Blast design parameters were selected to: (1) minimize displacement of broken rock conforming to throw control required of mining methods, (2) minimize seismic effects, and (3) create breakage at a cost economical to mining operations.

Jan 1, 1983

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.', ' Other methods employed are the drag and spiral classifiers and the hydroseparator.' These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952

By C. G. Grant, Wm. B. Price

This investigation of low copper-nickel silvers was untiertaken to check the work of Lèon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the mierostructure of the binary alloys of copper arid zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Lèon Guillet evolved his conception of "fictitious compositions." He states,' in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds. For example, if a 60:40 brass has 4 per cent. of tin substituted for 4 per cent. of zinc, the actual composition would analyze 60:36:4. Assuming that 1 per cent. of tin plays the same part as 2 per cent. of zinc, the proportions of copper and equivalent zinc may be stated as 60 parts of copper and 44 parts of zinc, which, figured to 100 per cent., gives an analysis of 57.7 per cent. of copper and 42.3 per cent. of zinc, the fictitious composition for a 60:36:4 tin brass. The relation between ternary alloys containing copper and zinc together with a third metal, and the microscopically equivalent binary alloy of copper and zinc, may be expressed mathematically.

Jan 1, 1924

By C. Watson Owings

"The mining Industry in the United States is becoming fully cognizant of the hazards of dust in underground mining as well as in surface plants. The dust problem in metal mines has been brought to focus through knowledge of the harmful effects of dust, especially silica, and through adoption of more or less stringent legislation classifying certain types of pneumoconiosis as occupational diseases. The coal-mining industry is aroused principally by the apparently great increase in the dust-explosion hazard resulting from the rapid growth of mechanized mining. The United States Department of the Interior, through the Safety. Division of the Bureau of Mines, has been requested repeatedly to recommend methods of allaying dust in both coal and metal mines. Methods adequate under hand-mining conditions fail to effect satisfactory reduction of dust in more rapid extraction with modern equipment. Studies of methods and equipment for allaying dust are being conducted in both metal and coal mines. Results of these studies are discussed, and indications of possible means of reducing dust concentrations are presented in the hope that the health and 'safety of men employed in the mining industry may be increasingly safeguarded.DUSTThe term ""dust"" is a common one, and yet the meaning is applied to widely different particle sizes. The general term means ""earth or other matter reduced to fine, dry, and powdery particles."" The root from which the word is derived means ""something that can be blown about by the wind."" As a result of tests on the explosibility of coal, the Federal Bureau of Mines has arbitrarily defined dust as being. ""that which will pass through a 20-mesh screen,"" based upon the fact that particles coarser than 20-mesh have little influence on the development of an explosion of Pittsburgh coal-bed dust. The study of dust, from a health standpoint, has given rise to still another definition of dust, namely,- according to Drinker3/, ""solid particles ranging in size from less than 1 micron to about 150 microns."" A micron is 1/25,400 inch, and 150 microns are approximately 1/1,700 inch. Atmospheric dust usually is considered as 10 microns or less, larger particles not being counted under the microscope in determination of dust concentrations."

Apr 1, 1942

By Walter Keune

Object Modeling Technique. This formal descriptive language makes it possible to formulate requirements in the real world in such a way that they can be implemented in the form of entities (cf. Entity Relationship Model[Che83]) and methods (see Figure 1). The object {Roadway} is graphically depicted by means of the Polygon method.

Jan 1, 1996

By Wayne E. Glenn

The San Miguelito Field of Ventura County, California, lies along the coast approximately five miles northwest of the city of Ventura. The structure is one of several in the Ventura anticline, a series of anticlinal folds trending northwest-southeast through the San Miguelito Field. The Ventura Avenue Field lies to the southeast along the anticline, and Padre Canyon and Rin-con Fields lie to the northwest; the series then extends beneath the Pacific Ocean. Production is obtained from the Lower Pico and Repetto formations of Pliocene age, and oil accumulation is controlled by faulting, lithology and structure. The first well in the First Grubb Pool was completed in November, 1931, and to date 48 producing wells have been drilled on the 276 productive acres. Approximately 685 ft of net pay are contained in the eight sand bodies grossing 1,220 ft of section. Production of oil to date has been 15,-600,000 bbl. A gas injection project was instigated in April, 1940, but was discontinued in September, 1949. This paper is confined to a discussion of the development and performance history of the First Grubb Pool of the San Miguelito Field. LOCATION AND GEOLOGY The San Miguelito Oil Field is located in Ventura County about five miles northwest of the city of Ventura along the coastal highway to Santa Barbara. It is located within sections 23, 24, 25, and 30 of Township 3 North, Range 24 West, San Bernardino Base and Meridian. Surface elevation in the field ranges from sea level to plus 1,200 ft, and the terrain is extremely rugged. The structure is well defined on the surface and on the wall of the Amphitheatre Canyon where appears a so-called "text book" anticlinal section. The San Miguelito structure is an asymmetrical, elongated anticline about two miles long and three-fourths of a mile wide. The trend of the axis of the anticline is northwest-southeast. Fig. 9 illustrates the contours and major faults of this structure. Dips on the southwesterly flank average about 40 degrees, whereas the northeasterly flank ranges from 60 to 75 degrees. There are several faults striking generally east and west. These faults do not appear to affect materially the area of accumulation or performance behavior. It is believed that accumulation was affected by steeply dipping beds and extremely low permeability of the northeast flank of the structure. As shown by the typical log, Fig. 1. the San Miguelito Field is divided into two stratigraphic producing intervals. The First Grubb Pool comprises the interval from the "G" to "L" markers; the Second Grubb Pool from the "L" to "M" markers. The First Grubb Pool, ranging in thickness from 1,105 to 1,680 ft, with an average of 1,220 ft, includes approximately 685 ft of oil-bearing sands. The First Grubb zone consists of eight sand intervals separated by shales. The shale bodies separating the eight sand intervals within the First Grubb Pool are continuous throughout the major part of the structure and serve as an effective barrier. Many of the thin, irregular shale or siltstone streaks within these sand bodies are discontinuous and do not affect well performance appreciably. The productive horizons in the First Grubb Pool are siltstones and sandstones of the Lower Pico and Repetto formations of Pliocene age. It is apparent from inspection of the typical log that the "G" to "L" interval might have been separated into at least six producing zones and selectively pro. duced. Unfortunately the electric log and some of our modern tools were not available or were in their infancy dur. ing the period 1931 through 1937. Not until 1937 when eight wells had been completed were there sufficient geological data to permit definition of the sand bodies. Then the problem of reservoir control in this multiple-sand field, where all sands are open to a common

Jan 1, 1950

By R. Woodward Moore

A GRAPHICAL method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application.

Jan 1, 1944

By L O. ÆNeill, J Bebek

When Kalgoorlie Consolidated Gold Mines (KCGM) purchased its fleet of 18 CaterpillarÆs dump trucks in 1999, as part of its change to owner operated mining, five CaterpillarÆs Computer Aided Earthmoving Systems (CAES) were also commissioned on Komatsu PC8000 hydraulic shovels and Caterpillar D10R bulldozers. Since then the CAES system has been installed and operational on Komatsu PC3000 hydraulic shovel, CaterpillarÆs D10R dozers and Cat 994 front-end loader while Cat 854 wheel dozer has been fitted with CAESbasic. This investment in advanced machine guidance and control technology has proven very beneficial over the years for the Super Pit with improved safety and increased operating efficiency and productivity. The paper brings into focus how the CAES system adaptation in unique mining conditions assists in production gain, equipment operatorÆs safety, flexibility and independence, personnel removal from hazardous areas, acquisition of operational information and improvements in mine planning and design, benefiting the entire mining operation.

Jan 1, 2003

By Vidal Navarro

Actualmente el enfoque sobre los problemas ambientales no se puede desligar de la seguridad y salud ocupacional. Por ello, es necesario desarrollar una reingeniería en el aspecto ambiental subterráneo, donde se introduzca el concepto ambiental que tiene plena aplicabilidad. En ese sentido, el presente trabajo introduce una metodología que consiste en la evaluación del riego ambiental subterráneo debido a factores contaminantes relacionados a la temperatura, velocidad y caudal del aire, así como señala algunos resultados de las investigaciones realizadas, donde se usaron el programa VnetPC2000 entre otros, con aplicación a minas subterráneas de Portugal y con resultados altamente positivos.

Aug 25, 2002

By KAZUKO RAMOS NISIOKA

Nesse trabalho é proposto uma investigação das propriedades eletrônicas de junções moleculares de Nanofitas ZigueZague de Grafeno (NZZG) e Phagrafeno (NZZPG) por meio da Teoria: 1- DFT/B3LYP/6-311G(d,p) para otimizar a geometria das moléculas; 2- DFT/LDA.PZ/DZP sobre a célula unitária da rede cristalina para obter as propriedades eletrônicas; 3- Teoria de Hückel Estendido/Função de Green de Não Equilíbrio (THE/FGNE) através da fórmula de Landauer-Buttiker para a região central acoplada entre 2 eletrodos. Nossos resultados exibem: (i) comportamento condutor e singularidades de Van-Hove; (ii) uma região não linear com característica de um dispositivo usual TEC para NZZG; (iii) duas regiões não lineares (RDNs) mostrando característica de um diodo túnel com 2 janelas de operação para NZZPG. Essas regiões não lineares de voltagem coincidem com os Vmin nas curvas Fowler-Nordheim (FN) e Lauritsen-Millikan (LM).

Oct 30, 2017

By William Bourcier

Geothermal Brines are a significant potential source of valuable minerals and metals. These brines are water that is heated by the natural heat flow from the depths of the earth. Hotter brines, typically with temperatures greater than 120°C, are used to generate electricity. Lower temperature brines are directly used to supply thermal energy to applications such as agriculture, aquaculture and process/domestic heat. The geothermal waters have had intimate and lengthy contact with the layers of the earth?s crust that they flow through, resulting in dissolution of minerals and metals from the rocks, and solution into the hot water. These aqueous solutions can be processed to recover minerals and metals. Some potential products include silica, zinc and lithium, along with other materials. Recovery of minerals and metals from geothermal brines can be viewed as ?solution mining by nature?, followed by application of known or new hydrometallurgical techniques for isolation and purification. This paper discusses the opportunities, the processes, the challenges, the current status, the economics and the potential for recovery of minerals and metals from geothermal brines.

Jan 1, 2006

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

By Richard L. Coleman

El trabajo de ensayo metalúrgico para desarrollar un flujograma es el que ahora describimos, comenzando con una información experimentada requerida en todo momento hasta llegar a un esquema final de flujo de un proceso. Tanto las pruebas de laboratorio como de planta piloto son revisadas adecuadamente sobre las experiencias anteriores.

Jan 1, 1982