Search Documents

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By M. Verri

The paper describes the design options available for the simultaneous production of liquid sulphur dioxide, via cryogenic condensation, and sulphuric acid in a sulphur-burning sulphuric acid plant. The impact of the operating conditions of the cryogenic condensation on plant capital and operating costs are discussed, with the main focus on the optimization of the most important economic and operative drivers of the non-ferrous mining industry, such as energy efficiency, reliability, and availability. A case history relevant to an integrated sulphurburning plant producing liquid sulphur dioxide and sulphuric acid, recently started up in the Democratic Republic of Congo, is described. Keywords sulphur burning, sulphuric acid, liquid SO2, cryogenic SO2 condensation, liquid sulphur dioxide, sulphur dioxide.

Aug 1, 2013

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By Franklin R. Carpenter

In area, the Black Hills are about equal to the State of Connecticut. As the accompanying geological map indicates, they exhibit in the main a simple structure, presenting a central mass of granite and Archæan rocks, on all sides of which the later sedimentary rocks dip

Jan 1, 1889

By D. W. Smith

THE beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.1 R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 0 phase in the system copper-zinc takes the form of needles lying parallel to a [111.] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [111] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective 0 phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum.

Jan 1, 1932

By Ignacio González, Marcos Monroy, Valerie Bertrand, Roel Cruz

Results of an electrochemical study using carbon paste electrodes of pyrite and pyrrhotite samples suggest that the mineralogical impurities associated with these minerals are the determinant factor on their reactivity under alteration systems. These results were supported by mineralogical and leachate chemistry data from leach cell tests run on these samples. Pyrite reactivity decreases in the presence of associated impurities due to a galvanic effect whereas pyrrhotite reactivity appears to be controlled by the formation of a passivating layer, which overcome impurities effect. Electrochemical responses of sulfide-bearing samples provided valuable information on the prediction of ARD generation.

Jan 1, 2000

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993

Coal Division Mineral Industry Education Division Industrial Minerals Division Minerals Beneficiation Division Mineral Economics Division Mining, Geology and Geophysics Division Council R C Stephenson, Chairman (Ind Min Div), M D Cooper (Coal), H F Yancey (Coal), S D Michaelson (MBD), Will Mitchell, Jr (MBD), J R Van Pelt, Jr (MIED), S S Cole (Ind Min Div), J D Forrester (MGGD), L E Shaffer (MIED), E L Clark (MGGD), C W Merrill (MED), E H Robie, Acting Secretary, 29 West 39 Street, New York 18, New York

Jan 1, 1955

By Robert D. Brown

"All ten Canadian provinces have now tabled their 1981 /82 budgets . Only the provinces of Ontario, Quebec and British Columbia made more than minor modifications to their tax structures, with both Ontario and Quebec imposing major tax increases. In the past year, the federal budget was also released in the spring. Not so this year: we have that to look forward to in the fall!This month, Tax Notes presents a brief summary of the more significant tax changes introduced at the provinciallevels in the last months.Summary of provincial tax rate changesThe tax changes in this year's provincial budgets were both up and down- but there were far more tax increases than tax cuts.At the corporate tax level, two provinces, New Brunswick and British Columbia, increased their general corporate income tax rate; the former by two percentage points and the latter by one percentage point. Quebec, rather unexpectedly, sharply cut its corporate tax rate on business income, but increased some of its other business taxes at the same time. British Columbia reduced its corporate tax rate on small business income by two percentage points and Saskatchewan by one percentage point."

Jan 1, 1981

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By J. J. Calaman, D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast-holes in magnetic taconite at the preliminary taconite plant of .the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing machine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1. During three months of 1949 and continuously since February 1950, production piercing took place under all pit conditions. By the end of October 1950, a total of 15,000 linear ft of hole had been pierced in an open pit handling an average of 1200 to 1800 tons of crude a day in one 8-hr shift. While it is recognized that this output does not approach the millions of tons a year planned for the developing Minnesota taconite projects, the machine as a unit has been operating under conditions probably more adverse than those that eventually will be encountered in the large operations. This pilot operation has permitted evaluation of the piercing problem in the full-scale taconite plant. This paper describes jet-piercing process funda- mentals, important features of the latest jet-piercing burners and machine, actual piercing results obtained, and new developments that give promise of materially increasing overall process efficiency. To produce the blasthole, jet-piercing utilizes thermal energy, as contrasted with the application of mechanical energy in churn drills and jackham-mers. The heart of the process may be termed a tailored flame produced by a rocket-type burner, thermodynamically similar in every respect to that of the giant rockets being developed for military purposes. The heat release in the combustion chamber of the burner is about 50x10' Btu per cu ft per hr as compared with 5x10' for most modern steam generators.* Combustion of liquid petroleum fuels (kerosine, diesel oil, or No. 2 fuel oil) with gaseous oxygen in the burner chamber at pressures of 100 to 200 psi results in temperatures of about 4300°F. Expansion of the hot combustion gases through divergent nozzles produces high-temperature supersonic jets having measured velocities of about 6000 fps. Impinging the flame jets on rock causes a thin surface layer to expand and break away from the base as a result of the thermally induced stresses. This spalling action is aided further in chert and quartzite by the 0.82 pct volume change resulting from the 6 to p quartz inversion at 1066"F.t The dynamic action of the jets whisks the spalled rock

Jan 1, 1952

By H. T. Clark, S. Feigenbaum

THE importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct- reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermo- chemistry of steelmaking. The problem is not merely one of making a small number of temperature measurements in the open-hearth furnace. This has been done by several methods to a degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open- hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800° to 3100°F. are encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protection of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of .brittle materials, unsuited for handling on the open-hearth floor. The lie of the equipment was short and maintenance was an important consideration. EARLIER WORK Any one of a number of physical proper- ties of liquid steel could conceivably be used as a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1946

By L. Vinnett, J. Yianatos, S. Flores

"A numerical conditioning analysis for mineral recovery estimation was performed for industrial flotation plants, considering the copper (Cu), molybdenum (Mo) and iron (Fe) separability. A modified relative condition number, ?, was presented that allowed sensitivity analysis to be evaluated for the component recovery by means of an analytical formula. This closed form made it possible for the error propagation to be determined from feed, concentrate and tail grades with different orders of magnitude. The ? parameter can be evaluated using available grade data from the design criteria or historical mass balances, in which the variability is typically unknown. Reconciled data from different Cu/Mo concentrators were employed to evaluate the effect of small numerical disturbances in the grade data on the mineral recovery estimation. Higher error propagation was typically observed for Fe. The Mo minerals presented numerical problems, mainly in second cleaners and in the first cell of rougher banks. Lower condition numbers were observed for Cu due to the higher flotation rates.Mass-balance data reconciliation without redundancy was evaluated for a typical Cu/Mo flotation circuit using relative error minimization. Significant relative errors in the mineral recovery estimation were obtained with nonreconciled data in ill-conditioned problems. Negligible improvements in the mineral recovery estimation because of the data reconciliation with regard to the nonreconciled approach were obtained in well-conditioned problems. In addition, the improvements in mineral recovery estimation by using Cu, Mo and Fe in the data reconciliation were nonsignificant with respect to using only the best-conditioned component in well- and ill-conditioned problems.Despite the effort in data reconciliation and data repetition, poor performance may be obtained in ill-conditioned problems, which can deteriorate the flotation rate characterization. The error propagation has a negative impact on the mineral recovery of the first cell, which may significantly bias the flotation rate characterization of both valuable and nonvaluable elements.IntroductionMass balances have been extensively used in flotation processes to determine the mass flowrates (production) and mineral recovery (efficiency) of valuable minerals. Simple relationships for steadystate processes based on the feed, concentrate and tail grades can be obtained by taking a black-box approach. However, the calculation of concentrate flowrates from different components of the system, such as size fractions, chemical elements or minerals, does not satisfy the mass-conservation principle because of measurement errors (Smith and Ichiyen, 1973; Romagnoli and Sánchez, 2000). Mass-balance data reconciliation allows for obtaining a unique solution that satisfies the total and component mass balances, making small adjustments to the process data and taking advantage of the information redundancy (Narasimhan and Jordache, 2000). This methodology, which is based on a constrained weighted least-squares minimization, has proved to be robust when measurement errors are normally distributed, in the absence of gross errors.Commercial software has been developed to conduct massbalance data reconciliation in flotation processes, including MATBAL (Algosys, 2002), BILMAT (Algosys, 2013), JKMultibal (JKTech, 2013), BILCO (Caspeo, 2013) and HSC Chemistry (Outotec, 2013), which accomplish the reconciliation using known data accuracy in the optimization problem. The data accuracy can be obtained by sampling a stream n times in a run, known as repeats, each with independent chemical assays. Some unmeasured variables can be estimated using the measuring redundancy and sensor location. At present, grade and flow rate sensors may be incorporated in flotation to conduct real-time mass balances. However, a lack of sensor calibration and maintenance for suitable online measurements hinders the quality of the information. In"

Jan 1, 2016

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In previous reports 5 results were given of a manhole investigation carried out over a period from June 1929 to July 193C in cooperation with the Edison Electric Illuminating Co. of Boston. Mass., and during 1931 in cooperation with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co., to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by the Edison Electric Illuminating Co. and to develop methods of eliminating these hazards. These investigations have demonstrated that the detection, control, and elimination of combustible hazards in manholes can best be obtained by a close cooperation of the interested parties through a systematic and continuous inspection of manholes, under proper supervision.The investigation carried out during 1932 has been along lines similar to those conducted during 1929, 1930, and 1931 test crew consisting of two men, one an employee of the Consolidated Gas Co. and the other an employee of the Edison Electric Illuminating Co., was continuously employed during the year in the testing of gases in manholes served by the Edison system. The test crew was under the direct supervision of John Campbell, superintendent of the special service department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Consolidated Gas Co.As in the previous investigations, all tests were numbered. The test-data sheets, on which the information regarding the tests was recorded, were prepared in triplicate, ono copy going to the Edison Co., one to the gas company, and the third to the Bureau of Mines at Pittsburgh, Pa. These test-data sheets were then filed (1) according to the town, (2) the street location, and (3) the manhole number; in this way a complete record of each manhole tested was immediately available. A typical test-data sheet was given in the 1931 report. These data sheets were found to entirely satisfactory and no changes were made during the 1932 investigation. The procedure of sampling manhole atmospheres, shipment of the samples to Pittsburgh, and method of analysis has been the same as that described in the 1931 report and need not be repeated here. Likewise, there has been no change in the method of calculation of explosibility of the samples analyzed or the use of charcoal filter tests given in appendix A."

Jun 1, 1933

By B. J. Scheiner

As part of its mission to reduce pollution associated with mineral production, the Bureau of Mines is developing a dewatering technique for phosphatic clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong, stable flocs, which can be partially dewatered on a static screen and dewatered further on a rotary screen. Using this technique, a field test unit (FTU) was operated at a nominal 100 gal/min. Consolidated phosphatic clay material containing 20 percent solids was produced when feed slurries of 3 percent solids were treated with 0.69 pound of PEO per ton of feed solids. Pit and column tests indicated that the PEO-treated material continued to dewater; compacted products containing 40 percent solids were obtained after 45 days.

Jan 1, 1981

By A. J. Phillips, C. G. Grant, Wm. B. Price

Admiralty nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price' described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.~ A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimorr & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various a~ilounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by iiielting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of thcsc castings was polished and etched for examination. The castings were not homogenrous solid solutions, but showed the usual cored structure associated with cast alloys. Howcvrr, frorn an exarrlination of these sections we roughly determined

By M Philip Schwarz

"This paper reviews the status of computational modelling of a variety of common metals reduction processes, namely the blast furnace, rotary kiln and fluidised bed, and one new process not yet commercialised, namely smelting-reduction as in the HIsmelt Process. In each case, the last decade has seen the emergence of the capability to simulate the processes using multi-phase reacting computational fluid dynamics techniques. In some cases this capability is still in the process of being developed, and the next few years will see the maturing of the modelling techniques. As they become established, it will be possible to apply them to further refine the older technologies such as blast furnaces and rotary kilns, and assist in the optimisation, commercialisation and acceptance of the newer technologies such as fluidised bed and molten bath reduction. The development of a computational fluid dynamic model of bath smelting-reduction is described in some detail to illustrate how a large number of complex and interacting phenomena can be successfully simulated within a CFD framework. IntroductionPyrometallurgical reduction processes, such as the iron blast furnace, have become increasing more sophisticated through the centuries, so that today they are often highly efficient. There are continuing pressures, however, to refine existing processes and develop new ones. The imperatives are often economic, given that the long-term trend in the price of metals is always downward. In recent times, there has been the additional need to improve the environmental impact of metal production. Given that they almost inevitably require the use of carbon, metal reduction processes are large sources of greenhouse gases, and even a relatively small improvement in efficiency can be valuable in reducing CO2 production. Local environmental issues, such as the need to control of particulate emissions, are also driving incremental improvements in equipment.In addition to the economic and environmental drivers mentioned above, new process development is also being driven by the need to process new ores, and the need to produce unrefined metal in a form more compatible with alternative routes for downstream processing. An example of the latter is the production of DR! (Direct Reduced Iron) as a feed for EAF Electric Arc Furnace) in mini-mills.Further improvement of processes that have already been honed by continual plant experimentation over many years is not an easy task. To deliver further gains in efficiency, throughput, or product quality requires a highly sophisticated tool: one such tool· is computational modelling."

Jan 1, 2001